The analytical structures and the corresponding mathematical properties of the one dimensional and two dimensional fuzzy controllers are first investigated in detail. The nature of these two kinds of fuzzy controllers...The analytical structures and the corresponding mathematical properties of the one dimensional and two dimensional fuzzy controllers are first investigated in detail. The nature of these two kinds of fuzzy controllers is next probed from the perspective of control engineering. For the one dimensional fuzzy controller, it is concluded that this controller is a combination of a saturation element and a nonlinear proportional controller, and the system that employs the one dimensional fuzzy controller is the combination of an open-loop control system and a closedloop control system. For the latter case, it is concluded that it is a hybrid controller, which comprises the saturation part, zero-output part, nonlinear derivative part, nonlinear proportional part, as well as nonlinear proportional-derivative part, and the two dimensional fuzzy controller-based control system is a loop-varying system with varying number of control loops.展开更多
Fused deposition modeling （FDM） is an additive manufacturing technique used to fabricate intricate parts in 3D, within the shortest possible time without using tools, dies, fixtures, or human intervention. This arti...Fused deposition modeling （FDM） is an additive manufacturing technique used to fabricate intricate parts in 3D, within the shortest possible time without using tools, dies, fixtures, or human intervention. This article empiri- cally reports the effects of the process parameters, i.e., the layer thickness, raster angle, raster width, air gap, part orientation, and their interactions on the accuracy of the length, width, and thicknes, of acrylonitrile-butadiene- styrene （ABSP 400） parts fabricated using the FDM tech- nique. It was found that contraction prevailed along the directions of the length and width, whereas the thickness increased from the desired value of the fabricated part. Optimum parameter settings to minimize the responses, such as the change in length, width, and thickness of the test specimen, have been determined using Taguchi＇s parameter design. Because Taguchi＇s philosophy fails to obtain uniform optimal factor settings for each response, in this study, a fuzzy inference system combined with the Taguchi philosophy has been adopted to generate a single response from three responses, to reach the specific target values with the overall optimum factor level settings. Further, Taguchi and artificial neural network predictive models are also presented in this study for an accuracy evaluation within the dimensions of the FDM fabricated parts, subjected to various operating conditions. The pre- dicted values obtained from both models are in good agreement with the values from the experiment data, with mean absolute percentage errors of 3.16 and 0.15, respectively. Finally, the confirmatory test results showed an improvement in the multi-response performance index of 0.454 when using the optimal FDM parameters over the initial values.展开更多
基金This project was supported by the fundation of the Academy of Finland (201353)
文摘The analytical structures and the corresponding mathematical properties of the one dimensional and two dimensional fuzzy controllers are first investigated in detail. The nature of these two kinds of fuzzy controllers is next probed from the perspective of control engineering. For the one dimensional fuzzy controller, it is concluded that this controller is a combination of a saturation element and a nonlinear proportional controller, and the system that employs the one dimensional fuzzy controller is the combination of an open-loop control system and a closedloop control system. For the latter case, it is concluded that it is a hybrid controller, which comprises the saturation part, zero-output part, nonlinear derivative part, nonlinear proportional part, as well as nonlinear proportional-derivative part, and the two dimensional fuzzy controller-based control system is a loop-varying system with varying number of control loops.
文摘Fused deposition modeling （FDM） is an additive manufacturing technique used to fabricate intricate parts in 3D, within the shortest possible time without using tools, dies, fixtures, or human intervention. This article empiri- cally reports the effects of the process parameters, i.e., the layer thickness, raster angle, raster width, air gap, part orientation, and their interactions on the accuracy of the length, width, and thicknes, of acrylonitrile-butadiene- styrene （ABSP 400） parts fabricated using the FDM tech- nique. It was found that contraction prevailed along the directions of the length and width, whereas the thickness increased from the desired value of the fabricated part. Optimum parameter settings to minimize the responses, such as the change in length, width, and thickness of the test specimen, have been determined using Taguchi＇s parameter design. Because Taguchi＇s philosophy fails to obtain uniform optimal factor settings for each response, in this study, a fuzzy inference system combined with the Taguchi philosophy has been adopted to generate a single response from three responses, to reach the specific target values with the overall optimum factor level settings. Further, Taguchi and artificial neural network predictive models are also presented in this study for an accuracy evaluation within the dimensions of the FDM fabricated parts, subjected to various operating conditions. The pre- dicted values obtained from both models are in good agreement with the values from the experiment data, with mean absolute percentage errors of 3.16 and 0.15, respectively. Finally, the confirmatory test results showed an improvement in the multi-response performance index of 0.454 when using the optimal FDM parameters over the initial values.
