Optimization Mechanism of Mechanical Properties of Basalt Fiber-Epoxy Resin Composites by Interfacially Enriched Distribution of Nano-Starch Crystals

Fibre reinforced polymer composites have become a new generation of structural materials due to their unique advantages such as high specific strength,designability,good dimensional stability and ease of large-area monolithic forming.However,the problem of interfacial bonding between the resin matrix and the fibres limits the direct use of reinforcing fibres and has become a central difficulty in the development of basalt fibre-epoxy composites.This paper proposes a solution for enhancing the strength of the fibre-resin interface using maize starch nanocrystals,which are highly yield and eco-friendly.Firstly,in this paper,corn starch nanocrystals(SNC)were prepared by hydrolysis,and were deposited on the surface of basalt fibers by electrostatic adsorption.After that,in order to maximize the modification effect of nano-starch crystals on the interface,the basalt fiber-epoxy resin composite samples were prepared by mixing in a pressureless molding method.The test results shown that the addition of basalt fibers alone led to a reduction in the strength of the sample.Deposition of 0.1 wt%SNC on the surface of basalt fibers can make the strength consistent with pure epoxy resin.When the adsorption amount of SNC reached 0.5 wt%,the tensile strength of the samples was 23.7%higher than that of pure epoxy resin.This is due to the formation of ether bond homopolymers between the SNC at the fibre-epoxy interface and the epoxy resin,which distorts the originally smooth interface,leading to increased stress concentration and the development of cracks.This enhances the binding of basalt fibers.The conclusions of this paper can provide an effective,simple,low-cost and non-polluting method of interfacial enhancement modification.

Effect of glass fibre(GF) addition on microstructure and tensile property of GF/Pb composites fabricated by powder metallurgy

GF/Pb compositeswerefabricated by the method of powder metallurgy, and the density, microstructure and tensile propertywerecharacterized considering the size and content ofglass fibre （GF）. The results show that relative densities decrease with increasing GF fraction, and the 50μm-GF reinforced specimens exhibit a better densification than the 300μm-GF reinforced ones. The GF particles distribute quite uniformly inPb matrix, and the composites fabricated at low sintering temperature （〈200℃） possess fine-grain microstructure. The addition of GF significantly improves the strength of the Pb composites, and the ultimate tensile strength of the Pb composite reinforcedwith the addition of 50μm-0.5% GF（mass fraction）is about 30MPa higher than that of GF-free sample. For all composites groups, increasing the reinforcement content from 0.5%to 2%（mass fraction）results in a decrease in both tensile strength and ductility.

Damping properties of fly ash/epoxy composites

An inexpensive fly ash （FA）, which is from a waste product, was employed to prepare fly ash/epoxy composites. The purpose of this study is to characterize the contributions of matrix viscoelasticity, hollow structure characteristic （porosity）, and filler/matrix interface friction to the high vibration damping capacity of such composites. The damping properties of the composites were investigated in the temperature range of-40 to 150℃ and in the frequency range of 10 to 800 Hz by using a tension-compression mode. The results indicate that the peak value of damping loss factor （tan3） for the fly ash/epoxy composites can reach 0.70-0.90 in test specification, and the attenuation of damping loss factor is inconspicuous with increasing frequency. In addition, scanning electron microscope （SEM） was used to observe the morphology of the fly ash as well as its distribution in the matrix, which will help to analyze the effect of fly ash on the damping properties of the fly ash/epoxy composites.

Recent progress on thermal conductivity of graphene filled epoxy composites

With the rapid development of the electronic industry, the requirements for packaging materials with high thermal conductivity(TC) are getting higher and higher. Epoxy is widely used as package material for electronic package applications. But it’s intrinsic TC can’t meets the increasing demands. Adding high TC graphene into epoxy matrix is a proper way to reinforce epoxy composites. This review focuses on the filler modification,preparation process and thermal properties of graphene-filled epoxy resin composites. Different ways of covalent and non-covalent modification methods are discussed. The various kinds of graphene coating layer are also summarized. Then we analysis the hybrid filler system in epoxy composite. We hope this review will provide guidance for the development and application of graphene-filled epoxy resin composites.

Fabrication of BaTiO3/Epoxy Composites Exhibiting Large Dielectric Constant, Low Dielectric Loss and High Flexural Strength

BaTiO3/epoxy composites consisting of two three-dimensionally interpenetrating networks of BaTiO3 and epoxy phases were prepared using a new approach. The BaTiO3/epoxy composites exhibit a colossal dielectric constant, low dielectric loss and high flexural strength. In the BaTiO3 networks, chemically bonded grain boundaries between neighboring BaTiO3 grains were established, and they are responsible for the colossal dielectric constant and high flexural strength of the BaTiO3/epoxy composites. Furthermore, unlike the conventional ceramic/polymer composites, this approach also makes high loadings of BaTiO3 contents possible for the BaTiO3/epoxy composites without compromising their high flexural strength.

Epoxy Resin/Nano Ni@C Composites Exhibiting NTC Effect with Tunable Resistivity

Epoxy resin/Ni@C nanoparticle composites with aligned microstructure were prepared by using a procedure of magnetic field assisted curing. The results show that the resistivity of composites exhibits negative temperature coefficient （NTC） effect above room temperature, and can be adjusted by varying the content filler and the magnitude of magnetic field applied. Hill＇s quantum tunneling model was modified to understand the electrical conduction mechanism in the composites. It shows that the NTC effect ascribes to the dominant thermal activated tunneling transport of electron across adjacent nanoparticles, as well as the low thermal expansivity of epoxy resin matrix.

Microwave Absorption Properties of Carbon Nanotubes-Epoxy Composites in a Frequency Range of 2 - 20 GHz

In this work, multi-walled carbon nanotubes (MWCNTs)-epoxy composites with MWCNTs (outer diameter less 8 nm) loadings from 1 to 10 wt% were fabricated. The microstructures, dielectric constant, and microwave absorption properties of the MWCNTs-epoxy composite samples were investigated. The measurement results showed that the microwave absorption ratio of the MWCNTs-epoxy composite strongly depend on the MWCNT loading in the composites. The microwave absorption ratio up to 20%-26% around 18-20 GHz was reached for the samples with 8-10 wt% MWCNT loadings. The high absorption performance is mainly attributed to the microwave absorption of MWCNTs and the dielectric loss of MWCNTs-epoxy composites.

Research on properties of hollow glass microspheres/epoxy resin composites applied in deep rock in-situ temperature-preserved coring

Deep petroleum resources are in a high-temperature environment.However,the traditional deep rock coring method has no temperature preserved measures and ignores the effect of temperature on rock porosity and permeability,which will lead to the distortion of the petroleum resources reserves assessment.Therefore,the hollow glass microspheres/epoxy resin(HGM/EP)composites were innovatively proposed as temperature preserved materials for in-situ temperature-preserved coring(ITP-Coring),and the physical,mechanical,and temperature preserved properties were evaluated.The results indicated that:As the HGM content increased,the density and mechanical properties of the composites gradually decreased,while the water absorption was deficient without hydrostatic pressure.For composites with 50 vol%HGM,when the hydrostatic pressure reached 60 MPa,the water absorption was above 30.19%,and the physical and mechanical properties of composites were weakened.When the hydrostatic pressure was lower than 40 MPa,the mechanical properties and thermal conductivity of composites were almost unchanged.Therefore,the composites with 50 vol%HGM can be used for ITPCoring operations in deep environments with the highest hydrostatic pressure of 40 MPa.Finally,to further understand the temperature preserved performance of composites in practical applications,the temperature preserved properties were measured.An unsteady-state heat transfer model was established based on the test results,then the theoretical change of the core temperature during the coring process was obtained.The above tests results can provide a research basis for deep rock in-situ temperature preserved corer and support accurate assessment of deep petroleum reserves.

Strength, Fatigue Strength and Stiffness of High-Tech Bamboo/Epoxy Composites

A major problem in the strength data available for cellulose fibre-based materials is that the moisture content of the test specimens is rarely measured, and yet it is the dominant variable in the tests. Detailed strength and stiffness results are presented for Brazilian Dendrocalamus Giganteus bamboo at a wide range of moisture contents down to 2% and the fatigue curve is given for Chinese Moso bamboo at 4% moisture content. Techniques are described for handling the variability of these natural materials, both in design and in manufacturing quality control, for the mass production of large, high-tech composites wind turbine blades.

The Reinforcing Effect of Graphene on the Mechanical Properties of Carbon-Epoxy Composites

Graphene nanoplatelets (GNPs) are novel nanofillers holding attractive characteristics, including vigorous compatibility with majority polymers, outstanding mechanical, thermal, and electrical properties. In this study, the outstanding GNPs filler was reinforced to the epoxy matrix and carbon fabric/epoxy hybrid composite slabs to enrich their mechanical properties. Graphene nanoplatelets of 0.5, 1, 1.5 and 2 weight percentages were integrated into the epoxy and the physico-mechanical (microstructure, density, tensile, flexural and impact strength) properties were investigated. Furthermore, the mechanical properties of unfilled and 1 wt% GNPs filled carbon fabric/epoxy hybrid composite slabs were investigated. Subsequently, noteworthy improvement in the mechanical properties was conquered for the carbon fabric/epoxy hybrid composites.

Toughness and Fracture Mechanism of Carbon Fiber Reinforced Epoxy Composites

The fracture toughness of carbon fiber reinforced epoxy composite(CFRP)was investigated through mode I and mode II shaped fracture system in this paper.A novel polyimide with trifluoromethyl groups and grafted nanosilica were used to modify epoxy resin.Effect of modified resin and unmodified resin on fracture toughness of CFRP was compared and discussed.Lay-up angles and thicknesses effects on fracture toughness of composites were also investigated.The fracture toughness of CFRP was obtained through double cantilever beam(DCB)and end notched flexure(ENF)tests.The results showed that the composites prepared by modified resin exhibited high fracture toughness compared with unmodified composites.The fracture toughness value of mode I increased from 1.83 kJ/m2 to 4.55 kJ/m2.The fracture toughness value of mode II increased from 2.30 kJ/m2 to 6.47 kJ/m2.

Processing and Characterization of PMMA Nanofiber Reinforced Epoxy Composites

Growing demand for high-performance materials is driving the development of composites with nano material reinforcement. The use of nano reinforcement can provide a distinct advantage due to high surface area of the material. There are still many challenges in achieving the full potential of nanocomposites. In this paper, we investigate the performance of epoxy nanocomposites reinforced with short polymethyl methacrylate (PMMA) nanofibers. PMMA nanofibers were chopped and mixed with the epoxy resin and then the mixture was poured into a mould. Samples were cut to an appropriate size after cure and mechanical testing was carried out. Tensile and flexural strength and modulus were evaluated for samples with various fiber volume fractions to determine changes in mechanical performance. Also Scanning Electron Microscopy was utilized to investigate fracture surface and fiber-matrix interface. Results indicated that mechanical performance dropped as volume fraction of fibers increased, namely poor fiber-matrix adhesion and presence of porosity resulted in deterioration in strength and modulus. Further research is required to develop fiber coating system to enhance performance of the nanocomposite by improving fiber-matrix adhesion and fiber wet-out.

Detecting Impact Damage in Carbon Fabric/epoxy-matrix Composites by Ultrasonic F-scan and Electrical Resistance Measurement

The status and the variation of electrical resistance of impacted carbon fiber/epoxy-matrix composites were studied by ultrasonic F-scan and electrical resistance measurement The experimental results shows that impact damage energy threshold value of carbon fabric/epoxy-matrix composites can determine by using ultrasonic F-scan. When the impact energy exceeds the threshold value, damage is generated in composites. Electrical resistance of impacted composites is changed owing to the contact of each carbon fiber unit in composites, which cause a change of the series-parallel in conductors. The veracity of detecting impact damage in composites can be improved in this case.

High microwave absorption performances for single-walled carbon nanotube–epoxy composites with ultra-low loadings

Microwave-absorbing polymeric composites based on single-walled carbon nanotubes （SWNTs） are fabricated via a simple yet versatile method, and these SWNT-epoxy composites exhibit very impressive microwave absorption perfor- mances in a range of 2 GHz-18 GHz. For instance, a maximum absorbing value as high as 28 dB can be achieved for each of these SWNT-epoxy composites （1.3-mm thickness） with only 1 wt% loading of SWNTs, and about 4.8 GHz bandwidth, corresponding to a microwave absorption performance higher than 10 dB, is obtained. Furthermore, such low and appro- priate loadings of SWNTs also enhance the mechanical strength of the composite. It is suggested that these remarkable results are mainly attributable to the excellent intrinsic properties of SWNTs and their homogeneous dispersion state in the polymer matrix.

Synthesis, Characterization and Flame-retardant Properties of Epoxy Resins and AACHH Composites

Flame retardant epoxy resins were prepared by a simple mixed method using ammonium aluminum carbonate hydroxy hydrate （AACHH） as a halogen-free flame retardant. The prepared samples were characterized by X-ray diffraction, thermogravimetric and differential scanning calorimetry, scanning electron microscope and limiting oxygen index（LOI） experiments. Effects of AACHH content on LOI of epoxy resins/AACHH composite and flame retardant mechanism were investigated and discussed. Results show that AACHH exhibites excellent flame-retardant properties in epoxy resin（EP）. When the content of AACHH was 47.4%, the LOI of EP reached 32.2%. Moreover, the initial and terminal decomposition temperature of EP increased by 48 ℃ and 40 ℃, respectively. The flame retarded mechanism of AACHH is due to the synergic flame retardant effects of diluting, cooling, decomposition resisting and obstructing.

Phosphorylated Salicylic Acid as Flame Retardant in Epoxy Resins and Composites

A novel,versatile flame retardant substructure based on phosphorylated salicylic acid(SCP)is described and used in the synthesis of new flame retardants for HexFlow
RTM6,a high-performance epoxy resin used in resin transfer molding processes as composite matrix.The starting material salicylic acid can be obtained from natural sources.SCP as reactive phosphorus chloride is converted with a novolak,a novolak containing 9,10-dihydro-9-oxa-10-phospha-phenanthrene-10-oxide(DOPO)substituents or DOPO-hydroquinone to flame retardants with sufficient thermal stability and high char yield.Additionally,these flame retardants are soluble in the resin as well as react into the epoxy network.The determined thermal stability and glass transition temperatures of flame retarded neat resin samples as well as the interlaminar shear strength of corresponding carbon fiber reinforced composite materials showed the applicability of these flame retardants.Neat resin samples and composites were tested for their flammability by UL94 and/or flame-retardant performance by cone calorimetry.All tested flame retardants decrease the peak of heat release rate by up to 54%for neat resin samples.A combination of DOPO and SCP in one flame retardant shows synergistic effects in char formation and the mode of action adapts to neat resin or fiber-reinforced samples,so there is efficient flame retardancy in both cases.Therefore,a tailoring of SCP based flame retardants is possible.Additionally,these flame retardants efficiently reduce fiber degradation during combustion of carbon fiber-reinforced epoxy resins as observed by scanning electron microscopy and energy dispersive X-ray spectroscopy.

Preparation and Properties of Epoxy Piezoelectric Vibration Reduction Composites

The epoxy resin (E-51) was used as polymer matrix,conductive carbon black (CB) as conductive filler,and PZT was used to prepare a composite by curing.The effects of PZT and CB content on the properties of PZT/ CB/ EP piezoelectric composite were studied.When the PZT content reaches 40 wt%,the optimized vibration attenuation properties of PZT/CB/EP materials could be achieved with a loss factor of 0.9 from room temperature to 60 ℃.With the increase of PZT content,the bending strength of PZT/CB/EP piezoelectric composite vibration reduction material firstly increased from 45 MPa to 65 MPa and then decreased to 38 MPa.At room temperature,the dielectric constant increased from 7 to 50,and the dielectric loss increased from 0.1 to 0.5.

Optical and Mechanical Properties of Ramie Fiber/Epoxy Resin Transparent Composites

The residual resources of ramie fiber-based textile products were used as raw materials.Ramie fiber felt(RF)was modified by NaClO_(2) aqueous solution and then impregnated with water-based epoxy resin(WER).RF/WER transparent composite materials were prepared by lamination hot pressing process.The composite materials’color difference,transmittance,haze,density,water absorption,and mechanical properties were determined to assess the effects of NaClO_(2) treatment and the number of ramie fiber layers on the properties of the prepared composites.The results showed significantly improved optical and mechanical properties of the RF/WER transparent composites after NaClO_(2) treatment.With the increase of ramie fiber layers,the composites’whiteness,transmittance,and water absorption decreased while the haze increased.For material with three layers,the optical transmittance in the visible light region was 82%,and the haze was 96%,indicating the material has both high transmittance and high haze characteristics.The tensile strength increases with the increase of the number of layers,and the tensile strength of the composite with six layers is 243 MPa.This study broadens the scope of application of ramie fiber as a new option for home decoration materials.

Preparation of Three-Dimensional Carbon Network Reinforced Epoxy Composites and Their Thermal Conductivity

As a thermosetting resin with excellent properties,epoxy resin is used in many areas such as electronics,transportation,aerospace,and other fields.However,its relatively low thermal conductivity limits its wide application in more demanding fields.Here,a three-dimensional carbon(3DC)network was prepared through NaCl template-assisted in situ chemical vapor deposition(CVD)and used to reinforce epoxy resin for enhancing its thermal conductivity.The 3DC was prepared with a molar ratio of sodium atom to carbon atom of 100:20,and argon atmosphere in CVD led to an optimal improvement in the thermal conductivity of epoxy resin.The thermal conductivity of epoxy resin increased by 18%when the filling content was 3 wt.%of 3DC network because of the high contact area,uniform dispersion,and enhanced formation of conductive paths with epoxy resin.As the amount of 3DC addition increases,the thermal conductivity of composites also increases.As an innovative exploration,the work presented in this paper is of great significance for the thermal conductivity application of epoxy resin in the future.

Value-Added Utilization of Agro-Waste Derived Oil Palm Ash in Epoxy Composites

Oil palm ash(OPA)is an agro-industry waste and it has disposable problems.In the present study,an effort was made for value addition to OPA by incorporating it as a micro-filler in different concentration(0,10,20,30,40,and 50%)and sizes(100,200,and 300 mesh size particles)in the epoxy matrix.Prepared micro OPA was having a crystallinity index of 65.4%,high inorganic elements,and smooth surface morphology.Fabricated composites had higher void content as compared to neat epoxy matrix.Mechanical properties of fabricated composites had a maximum value at 30%loading of 300 mesh-size filler due to its low void content and size as compared to filler of 100 and 200 mesh size.Further increase in the concentration of OPA filler after 30 wt%of loading leads to the agglomeration of OPA microparticles and thereby resulted in the reduction of mechanical characteristics such as tensile strength,tensile modulus,flexural strength and flexural modulus of the composites.However,elongation at break decreased with increase in filler content at all percentage.Thermal stability and char residue percentage of composite increased with the concentration of filler at all percentage.Surface morphology of composite showed that OPA incorporation lead towards its roughness and cracks were originated from the site of OPA embedded in the epoxy matrix.The 300 mesh-size particles were having the best effect on composite as compared to 100 and 200 mesh-size filler.