In order to improve the control performance of strip rolling mill, theoretical model of the hydraulic gap control(HGC) system was established. HGC system offline identification scheme was designed for a tandem cold st...In order to improve the control performance of strip rolling mill, theoretical model of the hydraulic gap control(HGC) system was established. HGC system offline identification scheme was designed for a tandem cold strip mill, the system model parameters were identified by ARX model, and the identified model was verified. Taking the offline identified parameters as the initial values, online identification using recursive least square was carried out with model parameters changing. For the purpose of improving system robustness and decreasing the sensitivity due to model errors, the HGC system based on generalized predictive control(GPC) was designed, and simulation experiments for traditional controller and GPC controller were conducted. The results show that both controllers acquire good control effect with model matching. When the model mismatches, for the traditional controller, the overshot will increase to 76.7% and the rising time will increase to 165.7 ms, which cannot be accepted by HGC system; for the GPC controller, the overshot is less than 8.5%, and the rising time is less than 26 ms in any case.展开更多
The concept of control system of acceptable gap in the entrance ramp, the construction of the minimum acceptable gap and the method of determining it are introduced. On the above-mentioned basis and by taking the Chin...The concept of control system of acceptable gap in the entrance ramp, the construction of the minimum acceptable gap and the method of determining it are introduced. On the above-mentioned basis and by taking the Chinas reality into consideration, the issues on the design of control system of acceptable gap are approached in this paper.展开更多
A one dimensional model is developed for defective gap mode（DGM）with two types of boundary conditions：conducting mesh and conducting sleeve.For a periodically modulated system without defect,the normalized width of...A one dimensional model is developed for defective gap mode（DGM）with two types of boundary conditions：conducting mesh and conducting sleeve.For a periodically modulated system without defect,the normalized width of spectral gaps equals to the modulation factor,which is consistent with previous studies.For a periodic system with local defects introduced by the boundary conditions,it shows that the conducting-mesh-induced DGM is always well confined by spectral gaps while the conducting-sleeve-induced DGM is not.The defect location can be a useful tool to dynamically control the frequency and spatial periodicity of DGM inside spectral gaps.This controllability can be potentially applied to the interaction between gap eigenmodes and energetic particles in fusion plasmas,and optical microcavities and waveguides in photonic crystals.展开更多
双母管式机组较为广泛地应用于热电联产机组中,但由于多炉多机和2根大容量母管互相影响,导致热电负荷跟踪不及时,母管压力控制自动化水平较低。为此,针对双母管系统的非线性、强耦合、大迟延特性,设计了基于广义扩张状态观测器的多模型...双母管式机组较为广泛地应用于热电联产机组中,但由于多炉多机和2根大容量母管互相影响,导致热电负荷跟踪不及时,母管压力控制自动化水平较低。为此,针对双母管系统的非线性、强耦合、大迟延特性,设计了基于广义扩张状态观测器的多模型预测控制(generalized extended state observer based muti-model predictive control,GESOMMPC)方法。首先,建立了基于间隙度量(gap-metric)的多模型控制对象用于逼近非线性系统;其次,设计了扩张状态观测器估计系统耦合的集总扰动,并作为前馈信号输入到预测控制器中;最后,设计基于扰动前馈的多模型预测控制器实现对双母管系统的控制。实验结果表明,相对于PID方法,所提方法在满足电热负荷的同时,可以在允许范围内保持母管压力稳定,且动态偏差更小,过渡过程时间更短。展开更多
基金Project(51074051)supported by the National Natural Science Foundation of ChinaProject(20131033)supported by the Ph D Start-up Fund of Natural Science Foundation of Liaoning Province,ChinaProject(N140704001)supported by the Fundamental Research Funds for the Central Universities,China
文摘In order to improve the control performance of strip rolling mill, theoretical model of the hydraulic gap control(HGC) system was established. HGC system offline identification scheme was designed for a tandem cold strip mill, the system model parameters were identified by ARX model, and the identified model was verified. Taking the offline identified parameters as the initial values, online identification using recursive least square was carried out with model parameters changing. For the purpose of improving system robustness and decreasing the sensitivity due to model errors, the HGC system based on generalized predictive control(GPC) was designed, and simulation experiments for traditional controller and GPC controller were conducted. The results show that both controllers acquire good control effect with model matching. When the model mismatches, for the traditional controller, the overshot will increase to 76.7% and the rising time will increase to 165.7 ms, which cannot be accepted by HGC system; for the GPC controller, the overshot is less than 8.5%, and the rising time is less than 26 ms in any case.
文摘The concept of control system of acceptable gap in the entrance ramp, the construction of the minimum acceptable gap and the method of determining it are introduced. On the above-mentioned basis and by taking the Chinas reality into consideration, the issues on the design of control system of acceptable gap are approached in this paper.
基金supported by National Natural Science Foundation of China(No.11405271)
文摘A one dimensional model is developed for defective gap mode（DGM）with two types of boundary conditions：conducting mesh and conducting sleeve.For a periodically modulated system without defect,the normalized width of spectral gaps equals to the modulation factor,which is consistent with previous studies.For a periodic system with local defects introduced by the boundary conditions,it shows that the conducting-mesh-induced DGM is always well confined by spectral gaps while the conducting-sleeve-induced DGM is not.The defect location can be a useful tool to dynamically control the frequency and spatial periodicity of DGM inside spectral gaps.This controllability can be potentially applied to the interaction between gap eigenmodes and energetic particles in fusion plasmas,and optical microcavities and waveguides in photonic crystals.
文摘双母管式机组较为广泛地应用于热电联产机组中,但由于多炉多机和2根大容量母管互相影响,导致热电负荷跟踪不及时,母管压力控制自动化水平较低。为此,针对双母管系统的非线性、强耦合、大迟延特性,设计了基于广义扩张状态观测器的多模型预测控制(generalized extended state observer based muti-model predictive control,GESOMMPC)方法。首先,建立了基于间隙度量(gap-metric)的多模型控制对象用于逼近非线性系统;其次,设计了扩张状态观测器估计系统耦合的集总扰动,并作为前馈信号输入到预测控制器中;最后,设计基于扰动前馈的多模型预测控制器实现对双母管系统的控制。实验结果表明,相对于PID方法,所提方法在满足电热负荷的同时,可以在允许范围内保持母管压力稳定,且动态偏差更小,过渡过程时间更短。
