Fuzzy Control Method for Gasoline Engine Idle Speed Control

In order to improve the steady and dynamic characteristic of the idle speed control and study the performance of the fuzzy control method for the idle speed control, a fuzzy control system is developed to control the idle speed of gasoline engine. The construction and working principle of the fuzzy controller are described, and the design procedure of the fuzzy controller is given in detail. The control parameters are determined by computer simulation. The simulation and experiments on the engine test bench show that the idle speed is controlled accurately both in stationary and in dynamic states, and the fuzzy control method is robust to the changes of engine parameters.

STUDY ON INJECTION AND IGNITION CONTROL OF GASOLINE ENGINE BASED ON BP NEURAL NETWORK

According to advantages of neural network and characteristics of operatingprocedures of engine, a new strategy is represented on the control of fuel injection and ignitiontiming of gasoline engine based on improved BP network algorithm. The optimum ignition advance angleand fuel injection pulse band of engine under different speed and load are tested for the samplestraining network, focusing on the study of the design method and procedure of BP neural network inengine injection and ignition control. The results show that artificial neural network technique canmeet the requirement of engine injection and ignition control. The method is feasible for improvingpower performance, economy and emission performances of gasoline engine.

Effects of working parameters on gasoline engine exergy balance

To improve the energy utilization efficiency of internal combustion （IC） engine, exergy analysis was conducted on a passenger car gasoline engine. According to the thermodynamic theory of IC engine, in-cylinder exergy balance model was built. The working processes of gasoline engine were simulated by using the GT-power. In this way, the required parameters were calculated and then gasoline engine exergy balance was obtained by programming on computer. On this basis, the influences of various parameters on exergy balance were analyzed. Results show that, the proportions of various forms of exergy in gasoline engine from high to low are irreversible loss, effective work, exhaust gas exergy and heat transfer exergy. Effective exergy proportion fluctuates with cylinder volumetric efficiency at full load, while it always increases with break mean effective pressure （BMEP） at part load. Exhaust gas exergy proportion is more sensitive to speed, and it increases with speed increasing except at the highest speed. The lower proportion of heat transfer exergy appears at high speed and high load. Irreversible loss is mainly influenced by load. At part load, higher BMEP results in lower proportion of irreversible loss; at full load, the proportion of irreversible loss changes little except at the highest speed.

Monolithic Catalysts with Low Noble-Metal Content for Exhaust Purification of Small Gasoline Engines

A series of low noble-metal coment monolithic catalysts for exhaust purification of small gasoline engines was investigated, and it was found that the Pt/Rh-OSM/Al2O3 （where OSM was oxygen storage material） catalyst with Ce0.5Zr0.5-MnOx（3%MnOx） OSM held low light-off temperature for CO, HC, and NO; quite wide three-way window, and outstanding thermal stability. The catalyst could efficiently comrol exhaust emission of small gasoline engines.

Turbocharging the DA465 gasoline engine

In order to improve performance of the DA465Q gasoline engine, a substantial amount of research was done to optimize its turbocharging system. The research led to the GT12 turbocharger being selected and its turbocharging parameters being settled. Based on these tests, rational matching was worked out for respective components of the turbocharging system. Results show that this turbocharger allows the engine to easily meet the proposed requirements for power and economic performance, giving insight into further performance improvements for gasoline engines.

Auto-Ignition and Heat Release Correlations for Controlled Auto-Ignition Combustion in Gasoline Engines

Auto-ignition and heat release correlations for controlled auto-ignition(CAI)combustion were derived from extensive in-cylinder pressure data of a four-stroke gasoline engine operating in CAI combustion mode.Abundant experiments were carried out under a wide range of air/fuel ratio,speed and residual gas fraction to ensure that the combustion correlations can be used in the entire CAI engine operation range.Furthermore,a more accurate method to compute the residual gas fraction was proposed by calculating the working fluid temperature at the exhaust valve close timing in the experiments.The heat release correlation was described in two parts,one is for the first slower heat release process at low temperature,and the other is for the second faster heat release process at high temperature.Finally the heat release correlation was evaluated on the single cylinder gasoline engine running with CAI combustion by comparing the experimental data with the 1-D engine simulation results obtained with the aid of the GT-Power simulation program.The results show that the predicted loads and ignition timings match closely with the measurements.

Framework for fault-tolerant speed tracking control of gasoline engines using the first principle-based engine model

Optimal engine torque management,a fundamental objective,depends predominantly on engine speed tracking performance.It ensures to attain desired speed profile in the presence of uncertainties,disturbances and malfunctions.On the other hand,certain requirements such as emissions control,fuel efficiency and drivability are degraded in case of poorspeed tracking.Furthermore,constraints on engine speed tracking performance are even more stringent for hybrid power-train architecture as crankshaft speed and engine torque are the basic variables for coordinated control.Speed tracking is also considered essential for gearshift control ofthe automatic transmission.In this research work,a framework for fault-tolerant speed tracking of the gasoline engine is proposed using the First Principle-based Engine Model(FPEM).A high-fidelity direct relationship between fuel injection input and engine speed is derived by the transformation of FPEM.Fault is induced in the fuel injection subsystem to generate the torque imbalance.Using the proposed framework,a second-order sliding mode-based control technique is applied to track desired speed profile by mitigating the faultsin the fuel injection subsystem.Reference data acquired from the engine test rig is used to demonstrate the offline validity and fault tolerance capabilities of the proposed framework in MATLAB/Simulink.

Experimental study of stratified lean burn characteristics on a dual injection gasoline engine

Due to increasingly stringent fuel consumption and emission regulation,improving thermal efficiency and reducing particulate matter emissions are two main issues for next generation gasoline engine.Lean burn mode could greatly reduce pumping loss and decrease the fuel consumption of gasoline engines,although the burning rate is decreased by higher diluted intake air.In this study,dual injection stratified combustion mode is used to accelerate the burning rate of lean burn by increasing the fuel concentration near the spark plug.The effects of engine control parameters such as the excess air coefficient(Lambda),direct injection(DI)ratio,spark interval with DI,and DI timing on combustion,fuel consumption,gaseous emissions,and particulate emissions of a dual injection gasoline engine are studied.It is shown that the lean burn limit can be extended to Lambda=1.8 with a low compression ratio of 10,while the fuel consumption can be obviously improved at Lambda=1.4.There exists a spark window for dual injection stratified lean burn mode,in which the spark timing has a weak effect on combustion.With optimization of the control parameters,the brake specific fuel consumption(BSFC)decreases 9.05%more than that of original stoichiometric combustion with DI as 2 bar brake mean effective pressure(BMEP)at a 2000 r/min engine speed.The NO_(x) emissions before threeway catalyst(TWC)are 71.31%lower than that of the original engine while the particle number(PN)is 81.45%lower than the original engine.The dual injection stratified lean burn has a wide range of applications which can effectively reduce fuel consumption and particulate emissions.The BSFC reduction rate is higher than 5%and the PN reduction rate is more than 50%with the speed lower than 2400 r/min and the load lower than 5 bar.

Characterization of Particle Emissions of Turbocharged Direct Injection Gasoline Engine in Transients and Hot Start Conditions

Reducing pollutant emissions,particularly soot particles emitted by internal combustion engines,is a major challenge for car manufacturers.In this paper,the experimental setup is a turbocharged three-cylinders gasoline direct injection engine installed on a HORIBA dynamic test driven by a HORIBA STARS computer.The particle-measuring device is a Pegasor Particles Sensor that measures the current carried by previously electrically charged particles.The hot engine stabilized tests,with lambda parameter lower or equal to one,have very low emission levels,unlike dynamic tests.As a consequence,the present paper deals with experiments in transient conditions.Unlike diesel engine,cycle tests show that particulate emissions vary widely.To understand the phenomenon,a simple transient was created and reproduced a hundred times in order to obtain enough data to analyze and compare these different tests.This transient starts from idle to reach the speed of 2000 r/min and 60 N·m in 5 s.To reach this point,it is necessary to stay in full load for about 3 s.The maximum deviations of particles reaches 85%with the standard deviationσ=18%.The cylinder pressure sensor shows significant variations at the very beginning of each transient,i.e.,during the first 500 ms.This kind of result was observed for Worldwide harmonized Light vehicles Test Cycles(WLTC)with a maximum deviations of particles reaching 75%withσ=30%,on Real Drive Emissions Cycle(RDE)with a maximum deviations of particles reaching 45%withσ=22%and for a 300 s Mini-Cycle with a maximum deviations of particles reaching 70%withσ=17%.The Mini-cycle is made up of the five largest accelerations of the WLTP cycle.A complete analysis highlights the importance of filling the first engine cycles.This depends on the opening speed of the throttle,the position of the crankshaft at the beginning of the transient,and the acceleration of the first cycles.But,the NO_(x) sensor shows very slight variations between each test.As a consequence,it appears that the variation of particles emissions is not only related to variation of equivalence ratio but with another setting,which may be the oil consumption.Finally,from these results,it is possible to determine a particle characterization function.It consists of two functions.The first one is the average of the emitted particles level which depends on the engine speed,engine acceleration,engine torque and torque acceleration.The second function,which corresponds to dynamic variations in emissions,mainly depends on oil consumption in the cylinder and on the combustion quality of the first transient engine cycles.

Optical characterization of nano-sized organic carbon particles emitted from a small gasoline engine

The nano-sized organic carbon （NOC） particles emitted from a small gasoline engine were characterized using various ex situ optical techniques to assess their hazardous impact. The exhaust gas was sampled iso-kinetically by a quartz probe and passed through de-ionized water to gather the hydrophilic car- bonaceous particulates as hydrosol. The hydrodynamic diameter of the particles ranged between 1.7 and 3.6 nm at no load, with a mean diameter of 2.4 nm. The particle size in the engine exhaust was found to increase at higher loads, which is attributed to coagulation of the particles. The chemical structure of the particles was analyzed using UV-vis and infra-red spectroscopy. Both the band gap energy and oscillator strength data evaluated from the UV-vis absorbance showed that the NOC particles contained polyaromatic hydrocarbon structures with three to five aromatic rings. Infra-red spectroscopy analysis further confirmed the presence of aliphatic and carbonyl functionalities in the aromatic structures of the particles. The fine size of the particles, their high number concentration for the type of the engine under study and their structural features, make the particles extremely hazardous for environment and health.

Estimation of Residual Exhaust Gas of Homogeneous Charge Compression Ignition Gasoline Engine Operating Under Negative Valve Overlap Strategy

To meet the requirements of the homogeneous charge compression ignition gasoline engine’s rapid cylinder exhaust gas rate and accurate control of combustion phasing,a residual exhaust gas rate model was proposed.A heat dissipation model for gas flow in the exhaust passage and exhaust pipe was established,and the exhaust gas was established.Flow through the exhaust valve was considered as an adiabatic expansion process,the exhaust temperature was used to estimate the temperature in the cylinder at the time that the valve was closed,and the cylinder exhaust gas rate was calculated.To meet the requirements of transient operating conditions,a first-order inertial link was used to correct the thermocouple temperature measurement.Addressing this delay problem and modification of the exhaust wall temperature according to different conditions effectively improved the accuracy of the model.The relative error between the calculated results of this model and the simulation results determined using GT-POWER software was within 3.5%.

Potential of secondary aerosol formation from Chinese gasoline engine exhaust

Light-duty gasoline vehicles have drawn public attention in China due to their significant primary emissions of particulate matter and volatile organic compounds（VOCs）. However,little information on secondary aerosol formation from exhaust for Chinese vehicles and fuel conditions is available. In this study, chamber experiments were conducted to quantify the potential of secondary aerosol formation from the exhaust of a port fuel injection gasoline engine. The engine and fuel used are common in the Chinese market, and the fuel satisfies the China V gasoline fuel standard. Substantial secondary aerosol formation was observed during a 4–5 hr simulation, which was estimated to represent more than 10 days of equivalent atmospheric photo-oxidation in Beijing. As a consequence, the extreme case secondary organic aerosol（SOA） production was 426 ± 85 mg/kg-fuel, with high levels of precursors and OH exposure. The low hygroscopicity of the aerosols formed inside the chamber suggests that SOA was the dominant chemical composition. Fourteen percent of SOA measured in the chamber experiments could be explained through the oxidation of speciated single-ring aromatics. Unspeciated precursors, such as intermediate-volatility organic compounds and semi-volatile organic compounds, might be significant for SOA formation from gasoline VOCs. We concluded that reductions of emissions of aerosol precursor gases from vehicles are essential to mediate pollution in China.

A comparison of hydrocarbons emission from engine running 85￣＃gasoline and M－100 methanol fuel

Increasing global interest in methanoi fuel has led us to investigate the exhaust emissionsof its engine. Analysis of its inorganic and organic emissions. such as CO. NO_x and hydrocarbons(total HC) have been widely reported. This paper presents an analysis of more than 20 kinds ofhydrocarbons in the emissions obtained from a spark-ignition Shanghai car running 85# gasoline anda comparison with emission from a Santana test car running M-100 methanol fuel. A set ofenrichment method has also been described. Test results show that at the current stage of methanolengine development the concentration of individual hydrocarbon including some poisonous substancesis lower than those of normal gasoline engine.

Application of the Computer Simulation Technique to Developing EFI Engine

The application of computer simulation technique to electronic controlled fuel injection(EFI) engine was studied to increase the development speed and improve the overall performance of the engine and car. On the basis of an EFI system developed by ourselves, the simulation model of the initial control data and engine operation points during a driving cycle and the car performance pridiction model were established. This method was applied to a mini car. The experiment showed that the simulated control data has good accuracy; and the engine test points and car performances obtained by simulation are useful for the matching of EFI system with gasoline engine and the development speed is increased.

Fuel Burning Rate Model for Stratified Charge Engine

A zero-dimensional single-zone double-curve model is presented to predict fuel burning rate in stratified charge engines, and it is integrated with GT-Power to predict the overall performance of the stratified charge engines. The model consists of two exponential functions for calculating the fuel burning rate in different charge zones. The model factors are determined by a non-linear curve fitting technique, based on the experimental data obtained from 30 cases in middle and low loads. The results show good agreement between the measured and calculated cylinder pressures, and the deviation between calculated and measured cylinder pressures is less than 5%. The zerodimensional single-zone double-curve model is successful in the combustion modeling for stratified charge engines.

Research on drilling parameters of engine-powered auger ice drill

Drilling operations in polar regions and mountainous areas are complicated by nature of the extreme environment. Yet conventional rotary drilling technologies can be used to drill ice for scientific samples and oth- er research. Due to such reasons as power consumption and weight complications, it is hard to apply a conven- tional rotary drilling rig for glacial exploration. Use of small, relatively lightweight, portable engine-powered drilling systems in which the drill lifting from the borehole is carried by the winch. It is reasonable enough for near-surface shallow ice-drilling down to 50 m. Such systems can be used for near-surface ablation-stakes in- stallation, also temperature measurements at the bottom of active strata layer, revealing of anthropogenie pollu- tion, etc. The specified used in this research is an auger ice drill powered by a gasoline engine. At this stage, it is crucial to choose effective drilling parameters such as weight on bit （WOB） and drill bit rotation rate. Sen- sors equipped on the rig have measured the main parameters of the drilling process, such as drill speed, WOB, drill rotation speed, torque and temperature. This paper addresses research on drilling parameters of engine powered auger ice drill and supplies some recommendations for optimization of any ice-core drilling process.

COMPOSITIVE EMISSION CONTROL SYSTEM OF GASOLINE VEHICLE

The working principle of a kind of compositive emission control system is inquired into, which includes exhaust heater, secondary air supplement, exhaust gas recirculation （EGR）, thermal reactor and catalytic converter, etc. The purification effect of CO, HC and NOx emission of the gasoline spark ignite （S.I.） engine is studied. The entire vehicle driving cycle tests based on the national emission standard and a series of the gasoline engine-testing bench tests including full load characteristic experiment, load characteristic experiment and idle speed experiment are done. The results show that the system has a very good emission control effect to CO, HC and NOx of gasoline engine. The construction of the system is very simple and can be mounted on the exhaust pipe conveniently without any alteration of the vehicle-use gasoline engine.