Investigation on the Novel High-performance Copper/Graphene Composite Conductor for High Power Density Motor

High-performance Cu/Graphene composite wire synergistically strengthened by nano Cr_(3)C_(2) phase was directly synthesized via hot press sintering followed by severe cold plastic deformation, using liquid paraffin and CuCr alloy powder as the raw materials. Since graphene is in situ formed under the catalysis of copper powder during the sintering process, the problem that graphene is easy to agglomerate and difficult to disperse uniformly in the copper matrix has been solved. The nano Cr_(3)C_(2)-particles nailed at the interface favor to improve the interface bonding. The Cu/Graphene composite possesses high electrical conductivity, hardness, and plasticity. The composite wire exhibits high electrical conductivity of 96.93% IACS, great tensile strength of 488MPa, and excellent resistance to softening. Even after annealing at 400℃ for 1 h, the tensile strength can still reach 268 MPa with a conductivity of about 99.14% IACS.The wire's temperature coefficient of resistance(TCR) is largely reduced to 0.0035/℃ due to the complex structure,which leads the wire to present low resistivity at higher temperatures. Such Cu/Graphene composite wire with excellent comprehensive performance has a good application prospect in high-power density motors.

Two-Step Synthesis of Sulfur/Graphene Composite Cathode for Rechargeable Lithium Sulfur Batteries

Sulfur/graphene composites with different sulfur contents were prepared by two-step synthesis, where graphene was regarded as a carrier of sulfur active substance. The surface structure and crystal form of the composites obtained were characterized and compared by X-ray diffraction （XRD）, scanning electron microscopy （SEM）, and transmission electron microscopy （TEM）. It was found that sulfur was partially coated by graphene. The graphene folds provided more nano-pores and electron transport channels for sulfur. From TGA results, the sulfur contents of the sulfur/graphene compositcs measured were about 42.32 wt%, 54.94 wt%, and 65.23 wt%. Electrochemical tests demonstrated that sulfur/graphene composite （x=54.94 wt%） cathode exhibited better capacity retention （40.13%） compared with the pure cathode （20.46%）, where an initial discharge capacity was up to 1 500 mAh.g-t and it remained about 600 mAh·g-1 after 30 cycles. Furthermore, the electrochemical reaction mechanism and the state of reaction interface for Li/S battery were analyzed by cyclic voltammogram and AC-impedance spectra. The results indicated that the sulfur/graphene composite with a sulfur content of 54.94 wt%, based on a two-step synthesis, contributed to improving electrochemical properties of lithium/sulfur battery

Preparation of TiO2 Nanocrystals/Graphene Composite and Its Photocatalytic Performance

TiO2 nanocrystals/graphene （TiO2/GR） composite are prepared by combining flocculation and hydrothermal reduction technology using graphite oxide and TiO2 colloid as precursors. The obtained materials are examined by scanning electron microscopy, transition electron microscopy, X-ray diffraction, N2 adsorption desorption, and ultraviolet-visible diffuse spectroscopy. The results suggest that the presence of TiO2 nanocrystals with diameter of about 15 nm prevents GR nanosheets from agglomeration. Owing to the uniform distribution of TiO2 nanocrystals on the GR nanosheets, TiO2/GR composite exhibits stronger light absorption in the visible region, higher adsorption capacity to methylene blue and higher efficiency of charge separation and transportation compared with pure TiO2. Moreover, the TiO2/GR composite with a GR content of 30% shows higher photocatalytic removal efficiency of MB from water than that of pure TiO2 and commercial P25 under both UV and sunlight irradiation.

Ultralow detection limit of giant magnetoresistance biosensor using Fe3O4–graphene composite nanoparticle label

A special Fe3O4nanoparticles–graphene（Fe3O4–GN） composite as a magnetic label was employed for biodetection using giant magnetoresistance（GMR） sensors with a Wheatstone bridge. The Fe3O4–GN composite exhibits a strong ferromagnetic behavior with the saturation magnetization MS of approximately 48 emu/g, coercivity HC of 200 Oe, and remanence Mr of 8.3 emu/g, leading to a large magnetic fringing field. However, the Fe3O4 nanoparticles do not aggregate together, which can be attributed to the pinning and separating effects of graphene sheet to the magnetic particles. The Fe3O4–GN composite is especially suitable for biodetection as a promising magnetic label since it combines two advantages of large fringing field and no aggregation. As a result, the concentration x dependence of voltage difference ｜？V｜ between detecting and reference sensors undergoes the relationship of ｜？V｜ = 240.5 lgx ＋ 515.2 with an ultralow detection limit of 10 ng/mL（very close to the calculated limit of 7 ng/mL） and a wide detection range of 4 orders.

Supposition of graphene stacks to estimate the contact resistance and conductivity of nanocomposites

In this study,the effects of stacked nanosheets and the surrounding interphase zone on the resistance of the contact region between nanosheets and the tunneling conductivity of samples are evaluated with developed equations superior to those previously reported.The contact resistance and nanocomposite conductivity are modeled by several influencing factors,including stack properties,interphase depth,tunneling size,and contact diameter.The developed model's accuracy is verified through numerous experimental measurements.To further validate the models and establish correlations between parameters,the effects of all the variables on contact resistance and nanocomposite conductivity are analyzed.Notably,the contact resistance is primarily dependent on the polymer tunnel resistivity,contact area,and tunneling size.The dimensions of the graphene nanosheets significantly influence the conductivity,which ranges from 0 S/m to90 S/m.An increased number of nanosheets in stacks and a larger gap between them enhance the nanocomposite's conductivity.Furthermore,the thicker interphase and smaller tunneling size can lead to higher sample conductivity due to their optimistic effects on the percolation threshold and network efficacy.

Nanocellulose/nitrogen and fluorine co-doped graphene composite hydrogels for high-performance supercapacitors

Three-dimensional graphene materials have been studied as typical supercapacitors electrode materials by virtue of their ultrahigh specific surface area and good ion transport capacity.However,improvement of the poor volumetric electrochemical performance of these graphene materials has been required although they have high gravimetric energy density.In this work,nanocellulose/nitrogen and fluorine co-doped graphene composite hydrogels(NC-NFGHs)were prepared through a convenient hydrothermal approach utilizing ammonium fluoride as the heteroatom source.Nanocellulose(NC)and high concentration of graphene oxide(GO)were utilized to adjust the structure of NC-NFGHs and increase their packing density.Subsequently,the aqueous symmetric supercapacitor based on NC-NFGH-80 exhibits remarkable gravimetric(286.6 F·g^(-1))and volumetric(421.3 F·cm^(-3))specific capacitance at 0.3 A·g^(-1),good rate performance,and remarkable cycle stability up to 10,000 cycles.Besides,the all-solid-state flexible symmetric supercapacitors(ASSC)fabricated by NC-NFGH-80 also delivered a large specific capacitance of 117.1 F·g^(-1)at 0.3 A·g^(-1)and long service life over 10,000 cycles at 10 A·g^(-1).This compact porous structure and heteroatom co-doped graphene material supply a favorable strategy for high-performance supercapacitors.

Direct synthesis of highly conductive poly（3,4- ethylenedioxythiophene）：poly（4-styrenesulfonate） （PEDOT：PSS）/graphene composites and their applications in energy harvesting systems

We report for the first time highly conductive poly（3,4-ethylenedioxythiophene）： poly（4-styrenesulfonate） （PEDOT：PSS）/graphene composites fabricated by in situ polymerization and their applications in a thermoelectric device and a platinum （Pt）-free dye-sensitized solar cell （DSSC） as energy harvesting systems. Graphene was dispersed in a solution of poly（4-styrenesulfonate） （PSS） and polymerization was directly carried out by addition of 3,4-ethylenedioxythiophene （EDOT） monomer to the dispersion. The content of the graphene was varied and optimized to give the highest electrical conductivity. The composite solution was ready to use without any reduction process because reduced graphene oxide was used. The fabricated film had a conductivity of 637 S.cm-1, corresponding to an enhancement of 41%, after the introduction of 3 wt.% graphene without any further complicated reduction processes of graphene being required. The highly conductive composite films were employed in an organic thermoelectric device, and the device showed a power factor of 45.7 μW·m^-1K^-2 which is 93% higher than a device based on pristine PEDOT：PSS. In addition, the highly conductive composite films were used in Pt-free DSSCs, showing an energy conversion efficiency of 5.4%, which is 21% higher than that of a DSSC based on PEDOT：PSS.

A Facile One-Step Synthesis of TiOe/Graphene Composites for Photodegradation of Methyl Orange

TiO2/graphene composite photocatalysts have been prepared by a simple liquid phase deposition method using titanium tetrafluoride and electron beam （EB） irradiation-pretreated graphene as the raw materials. The products were characterized by X-ray diffraction, transmission electron microscopy, X-ray photoelectron spectroscopy, and thermogravimetric analysis. The effects of varying the synthesis parameters such as graphene content, concentration of titanium tetrafluoride solution and irradiation dose were investigated. It was found that the preparation conditions had a significant effect on the structure and properties of the final products. The irradiated graphene was covered with petal-like anatase TiO2 nanoparticles, which were more uniform and smaller in size than those in products synthesized without EB irradiation-pretreated graphene. The photocatalytic activities of the products were evaluated using the photocatalytic degradation of methyl orange as a probe reaction. The results showed that the products synthesized using EB irradiation-pretreated graphene exhibited higher photocatalytic activities than those using graphene without EB irradiation pretreatment.

Nonlinear vibration of functionally graded graphene platelet-reinforced composite truncated conical shell using first-order shear deformation theory

In this study,the first-order shear deformation theory(FSDT)is used to establish a nonlinear dynamic model for a conical shell truncated by a functionally graded graphene platelet-reinforced composite(FG-GPLRC).The vibration analyses of the FG-GPLRC truncated conical shell are presented.Considering the graphene platelets(GPLs)of the FG-GPLRC truncated conical shell with three different distribution patterns,the modified Halpin-Tsai model is used to calculate the effective Young’s modulus.Hamilton’s principle,the FSDT,and the von-Karman type nonlinear geometric relationships are used to derive a system of partial differential governing equations of the FG-GPLRC truncated conical shell.The Galerkin method is used to obtain the ordinary differential equations of the truncated conical shell.Then,the analytical nonlinear frequencies of the FG-GPLRC truncated conical shell are solved by the harmonic balance method.The effects of the weight fraction and distribution pattern of the GPLs,the ratio of the length to the radius as well as the ratio of the radius to the thickness of the FG-GPLRC truncated conical shell on the nonlinear natural frequency characteristics are discussed.This study culminates in the discovery of the periodic motion and chaotic motion of the FG-GPLRC truncated conical shell.

Mechanical and tribological behaviors of graphene/Inconel 718 composites

Graphene/Inconel 718 composites were innovatively synthesized through selective laser melting,and the mechanical and tribological performances of the grapheme-reinforced Inconel 718 matrix composites were evaluated.The composite microstructures were characterized by XRD,SEM and Raman spectroscopy.The results show that selective laser melting is a viable method to fabricate Inconel 718 matrix composite and the addition of graphene nanoplatelets leads to a significant strengthening of Inconel 718 alloy,as well as the improvement of tribological performance.The yield strength and ultimate tensile strength of 1.0%graphene/Inconel 718 composites(mass fraction)are 42%and 53%higher than those of pure material,and the friction coefficient and wear rate are 22.4%and 66.8%lower than those of pure material.The decrease of fraction coefficient and wear rate is attributed to the improved hardness of composites and the formation of graphene nanoplatelet protective layer on the worn surfaces.

Graphene-reinforced aluminum matrix composites prepared by spark plasma sintering

Graphene-reinforced 7055 aluminum alloy composites with different contents of graphene were prepared by spark plasma sintering（SPS）. The structure and mechanical properties of the composites were investigated. Testing results show that the hardness, compressive strength, and yield strength of the composites are improved with the addition of 1wt% graphene. A clean, strong interface is formed between the metal matrix and graphene via metallurgical bonding on atomic scale. Harmful aluminum carbide（Al_4C_3） is not formed during SPS processing. Further addition of graphene（above 1wt%） results in the deterioration in mechanical properties of the composites. The agglomeration of graphene plates is exacerbated with increasing graphene content, which is the main reason for this deterioration.

Deformation treatment and microstructure of graphene-reinforced metal matrix nanocomposites: A review of graphene post-dispersion

Graphene/aluminum(Gr/Al)composites have attracted the attention of researchers all over the world due to their excellent properties.However,graphene agglomerates easily because of the van der Waals force between graphite sheets,thereby affecting the performance of the composites.Decreasing the agglomeration of graphene and dispersing it uniformly in the Al matrix is a key challenge.In the preparation process,predispersion treatment and deformation treatment can play important roles in graphene dispersion.Researchers have conducted a series of research and literature reviews of the graphene predispersion and consolidation of composites.However,they paid less attention to post-deformation processing.This review summarizes different deformation treatments involved in the preparation process of Gr/Al composites and the evolution of the microstructure during the process.Research on deformation parameters is expected to further improve the properties of Gr/Al composites and would provide a deep understanding of the strengthening effect of graphene.

Protection and Functionalizing of Stainless Steel Surface by Graphene Oxide-Polypyrrole Composite Coating

The corrosion inhibition of metallic substrates is a prime issue for many potential applications where corrosion plays a crucial role. The development of carbon based on functionalized coatings could increase the lifetime of metallic substrates by inhibiting the corrosion process. Present work is an effort to develop a corrosion inhibiting composite coating of graphene oxide and polypyrrole for AISI （American Iron and Steel Institute） type 304 stainless steel substrates. The electrochemical galvanostatic deposition process was applied for coating development. The coating morphology and ability to cover the substrate surface was analyzed with a high-resolution scanning electron microscope. The coating＇s structural and electronic properties were analyzed with Raman spectroscopy. The investigation of corrosion inhibition involved open circuit potential, Tafel, and voltammetry analysis. The standard salt test ASTM （American Society for Testing and Materials） G48A for stainless steel substrate has also been studied. Significant enhancement of corrosion potential as well as pitting potential for the composite coated substrates has been noted. Furthermore, corrosion and breakdown potential increased upon changing the material from graphene oxide to its composite coating. During the salt test analysis, the durability of the composite coating was noted up to 72 h, which is the standard time scale. Based on experimental analysis, this composite material can be used as an effective carbon based on functionalized corrosion inhibitor for stainless steel substrates to increase their lifetime.

Narrow and Dual-Band Tunable Absorption of a Composite Structure with a Graphene Metasurface

A tunable absorber, composed of a graphene ribbon on two layers of TiO2-Au between two slabs of dielectric material all on a metal substrate, is designed and numerically investigated. The absorption of the composite structure varies with the geometrical parameters of the structure and the physical parameters of graphene at mid-infrared frequencies. The numerical simulation shows that a near-perfect absorption with single and alum bands can be achieved in a certain frequency range. We also analyze the electric and surface current distributions to study the dual-band absorber. The results show that the absorber can be tuned by the chemical potential and electron phonon relaxation time of graphene, and electromagnetically induced transparency phenomenon can be obtained. The results of this study may be beneficial in the fields of infrared communication, perfect absorbers, sensors and filters.

Synthesis and electrochemical properties of three-dimensional graphene/polyaniline composites for supercapacitor electrode materials

To improve the specific capacitance and rate capability of electrode material for supercapacitors, a three-dimensional graphene/polyaniline （3DGN/PANI） composite is prepared via in situ polymerization on GN hydrogel. PANI grows on the GN surface as a thin film, and its content in the composite is controlled by the concentration of the reaction monomer. The specific capacitance of the 3DGN/PANI composite containing 10 wt% PANI reaches 322.8 F.g-1 at a current density of 1 A.g-1, nearly twice as large as that of the pure 3DGN （162.8 F.g-1）. The capacitance of the composite is 307.9 F.g-1 at 30 A.g-1 （maintaining 95.4%）, and 89% retention after 500 cycles. This study demonstrates the exciting potential of 3DGN/PANI with high capacitance, excellent rate capability and long cycling life for supercapacitors.

Nickel Sulfide/Graphene/Carbon Nanotube Composites as Electrode Material for the Supercapacitor Application in the Sea Flashing Signal System

This work presents NiS/graphene/carbon nanotube （NiS/GNS/CNT） composites as electrode material for the supercapacitor application in sea flashing signal systems. NiS nanosheets were closely anchored on the conductive GNS-CNT networks. As a result, the NiS/GNS/CNT electrode showed a high specific capacitance of 2 377 F.g^-1 at 2 mV.s^-1 and good cycling stability compared with the pure NiS （1 599F.g^-1）. The enhanced electrochemical performances are attributed to the synergetic effect between the conductive carbon and the pseudo-capacitive NiS. The high performance supercapacitor may provide application in the sea flashing signal system.

Li Storage Performance for the Composite Structure Of Graphene and Boron Fullerene

We study the stability and performance of Li absorption on the composite structure （B80 C72） of boron fullerene and graphene by first-principles calculations. Our results show that the Li storage capacity of the composite structure is estimated to be at least Li54B80C72, which is steady with improved dispersibility and electronic conductivity. The composite structure could have the potential application as the anode material of Li-ion batteries with high Li storage capacity and great mechanical property.

Torsional postbuckling characteristics of functionally graded graphene enhanced laminated truncated conical shell with temperature dependent material properties

Buckling and postbuckling characteristics of laminated graphene-enhanced composite(GEC)truncated conical shells exposed to torsion under temperature conditions using finite element method(FEM)simulation are presented in this study.In the thickness direction,the GEC layers of the conical shell are ordered in a piece-wise arrangement of functionally graded(FG)distribution,with each layer containing a variable volume fraction for graphene reinforcement.To calculate the properties of temperaturedependent material of GEC layers,the extended Halpin-Tsai micromechanical framework is used.The FEM model is verified via comparing the current results obtained with the theoretical estimates for homogeneous,laminated cylindrical,and conical shells,the FEM model is validated.The computational results show that a piece-wise FG graphene volume fraction distribution can improve the torque of critical buckling and torsional postbuckling strength.Also,the geometric parameters have a critical impact on the stability of the conical shell.However,a temperature rise can reduce the crucial torsional buckling torque as well as the GEC laminated truncated conical shell’s postbuckling strength.

A graphene-enhanced high-barrier and fast-curing film for deep in situ condition preserved coring in coal seams

Scientific research on deep in situ resources is highly important to the theory and technology system construction for deep in-situ resource exploitation.To obtain high-condition preserved core samples,it is vital to maintain the original material,humidity and luminous flux information inside the core.Therefore,this study proposes a research and development strategy for a high-toughness and highbarrier sealing film based on the molecular structure design and filler synergistic enhancement via a deep solid-state sealing film using in situ substance preservation(ISP),in situ moisture preservation(IMP)and in situ light preservation(ILP)coring principles.A graphene/epoxy composite sealing film with a high barrier,high strength and high toughness was developed.The oxygen permeability of the film was 0.23 cm^(3)/(m^(2)·d),the water vapor permeability was 1.26 g/(m^(2)·d),and the light transmittance was 0.The tensile strength reached 15.4 MPa,and the toughness was 5242.9 kJ/m^(3).The results from the film substance and moisture preservation performance verification experiments showed that the sealing film had an excellent sealing effect on small molecules,such as water,alkanes and even ions,which further verified that the sealing film greatly contributed to the maintenance and preservation of deep in-situ resource reserves and abundance.

3D hierarchically porous NiO/Graphene hybrid paper anode for long-life and high rate cycling flexible Li-ion batteries

With the rapid emergence of wearable devices, flexible lithium-ion batteries(LIBs) are much more needed than ever. Free-standing graphene-based composite paper electrodes with various active materials have appealed wide applications in flexible LIBs. However, due to the prone-to-restacking feature of graphene layers, a long cycle life at high current densities is rather difficult to be achieved. Herein, a unique threedimensional(3D) hierarchically porous NiO micro-flowers/graphene paper(fNiO/GP) electrode is successfully fabricated. The resulting fNiO/GP electrode shows superior long-term cycling stability at high rates(e.g., storage capacity of 359 mAh/g after 600 cycles at a high current density of 1 A/g). The facile 3D porous structure combines both the advantages of the graphene that is highly conductive and flexible to ensure rapid electrons/ions transfer and buffer the volume expansion of NiO during charge/discharge,and of the micro-sized NiO flowers that induces hierarchical between-layer pores ranging from nanomicro meters to promote the penetration of the electrolyte and prevent the re-stacking of graphene layers. Such structural design will inspire future manufacture of a wide range of active materials/graphene composite electrodes for high performance flexible LIBs.