Energy field-assisted high-speed dry milling green machining technology for difficult-to-machine metal materials

Energy field-assisted machining technology has the potential to overcome the limitations of machining difficult-to-machine metal materials,such as poor machinability,low cutting efficiency,and high energy consumption.High-speed dry milling has emerged as a typical green processing technology due to its high processing efficiency and avoidance of cutting fluids.However,the lack of necessary cooling and lubrication in high-speed dry milling makes it difficult to meet the continuous milling requirements for difficult-to-machine metal materials.The introduction of advanced energy-field-assisted green processing technology can improve the machinability of such metallic materials and achieve efficient precision manufacturing,making it a focus of academic and industrial research.In this review,the characteristics and limitations of high-speed dry milling of difficult-to-machine metal materials,including titanium alloys,nickel-based alloys,and high-strength steel,are systematically explored.The laser energy field,ultrasonic energy field,and cryogenic minimum quantity lubrication energy fields are introduced.By analyzing the effects of changing the energy field and cutting parameters on tool wear,chip morphology,cutting force,temperature,and surface quality of the workpiece during milling,the superiority of energy-field-assisted milling of difficult-to-machine metal materials is demonstrated.Finally,the shortcomings and technical challenges of energy-field-assisted milling are summarized in detail,providing feasible ideas for realizing multi-energy field collaborative green machining of difficult-to-machine metal materials in the future.

Chip formation in high speed milling of Ti-6Al-4V alloy under nitrogen-oil-mist

High speed milling experiments using nitrogen-oil-mist as the cutting medium were carried out to investigate the characteristics of chip formation for Ti-6Al-4V alloy.Within the range of conditions employed(cutting speed,vc=190-300 m/min;cutting depth of axial,ap=5,7 mm),saw-tooth chips were produced in these experiments.During the macro and micro analysis of the Ti-6Al-4V chips,an optical microscope and a scanning electron microscope(SEM)were used to study the microstructure and the morphology of the chips,and the X-ray photoelectron spectroscopy(XPS)was employed for chemical analysis.Comparisons were made to study the influence of different cutting media(nitrogen-oil-mist,air-oil-mist and dry cutting condition)on chip formation.Results indicate that cutting media have significant effects on chip formation.Nitrogen-oil-mist is more suitable for improving the contact condition at chip-tool interface and increasing the tool life in high speed milling of Ti-6Al-4V alloy than air-oil-mist and dry cutting.

Prediction and Analysis of Surface Quality of Northeast China Ash Wood during Water-Jet Assisted CO_(2) Laser Cutting

As a natural and environmentally friendly renewable material,Northeast China ash wood(NCAW)(Fraxinus mandshurica Rupr.)was cut by water-jet assisted CO_(2) laser(WACL),the surface quality was evaluated by surface roughness of cut section.The surface roughness was measured by three-dimensional(3D)profilometry.Furthermore,the micromorphology of machined surface was observed by scanning electronic microscopy(SEM).Carbon content changes of machined surface were measured by energy dispersive spectrometer(EDS).A relationship between surface roughness and cutting parameters was established using response surface methodology(RSM).It is concluded that the cutting speed,laser power and water pressure played an important role in surface roughness of cut section.The surface roughness increased as an increase in laser power.It decreased caused by increasing of cutting speed and water pressure.Measurements revealed that the surface quality of NCAW part was improved using the optimized combination of cutting parameters.The established quadratic mathematical model of a good prediction is helpful for matching suitable cutting parameters to obtain expected surface quality.

Investigation of MQL-Employed Hard-Milling Process of S60C Steel Using Coated-Cermented Carbide Tools

The application of cutting fluids in machining brings out many benefits, but their use is accompanied by health and enviroment hazards. MQL （Minimum Quantity Lubricant） has become a preciously alternative solution for lubrication against dry machinning and flood cooling lubricant, and this is a step toward green machining. This paper presents a comprehensively experiemental study on investigation of MQL performance in hard milling of S60C steel for multiple responses, including surface quality, cutting forces and tool wear. Compared to dry milling, even-enhanced surfaces finish quality, 20% less cutting force （Ft） and almost 112% prolonged tool lifetime are achieved by using MQL with 5% Emulsion in hard milling. In addition, this study compared the performances of MQL milling by using 5% Emulsion to the peanut oil completely harmless to the enviroment. This encouraging result, therefore, reveals that the MQL-employed hard milling can enable significant improvement in productivity, product quality, and overall machining economy even after covering the additional cost of designing and implementing MQL system. Moreover, this study also shows the limitation of peanut oils employed in MQL and proposes the further research in novel additives to enhance the performance of cooling lubricant for vegetable oils.