为了研究表面纳米化对7055铝合金耐磨性能的影响,利用高能喷丸(high energy shot peening,HESP)技术对7055铝合金材料进行表面纳米化处理;在7055铝合金表面获得纳米结构。利用透射电镜分析纳米化前后微观组织的变化,同时对纳米化材料表...为了研究表面纳米化对7055铝合金耐磨性能的影响,利用高能喷丸(high energy shot peening,HESP)技术对7055铝合金材料进行表面纳米化处理;在7055铝合金表面获得纳米结构。利用透射电镜分析纳米化前后微观组织的变化,同时对纳米化材料表层进行残余应力及显微硬度测定,并采用球盘磨损试验机研究了纳米化表面对固定载荷条件下7055铝合金材料磨损性能的影响。结果表明:表面纳米化使7055铝合金材料表面发生严重塑性变形,材料表面分布较高幅值残余压应力,最大可达到-369 MPa,残余压应力层深度达0.6 mm;纳米化后试样显微硬度较基体提高了50%。摩擦磨损实验表明:表面纳米化从一定程度降低了7055铝合金材料表面摩擦系数,且磨损失重是未处理试样的32%,表明高能喷丸表面纳米化有效改善了7055铝合金材料的耐磨性能。展开更多
Isothermal and isochronal annealing was conducted to study the thermal stability of the nanocrystalline in the surface layer of Mg alloy AZ91D induced by high-energy shot peening(HESP) .Field emission scanning electro...Isothermal and isochronal annealing was conducted to study the thermal stability of the nanocrystalline in the surface layer of Mg alloy AZ91D induced by high-energy shot peening(HESP) .Field emission scanning electron microscope(FESEM) and X-ray diffractometer were used to characterize the microstructure.Results showed that nanocrystalline produced by HESP on the surface layer of the magnesium alloy AZ91D was 60-70 nm on average.The nanocrystalline could remain stable at about 100℃,and grew up slowly between 100℃ and 200℃.When the annealing temperature reached 300℃,the growth rate of the nanocrystalline increased significantly.The kinetic coefficient n of the nanocrystalline growth was calculated to be 2-3 and the grain growth activation energy Q=39.7 kJ/mol,far less than the self-diffusion activation energy of magnesium atoms in the coarse polycrystalline material.展开更多
High-energy shot peening （HESP）, a method to produce severe plastic deformation by high velocity flying balls, was applied on die cast magnesium alloy AZ91D. Effects of surface nanocrystallization by HESP and heat t...High-energy shot peening （HESP）, a method to produce severe plastic deformation by high velocity flying balls, was applied on die cast magnesium alloy AZ91D. Effects of surface nanocrystallization by HESP and heat treatment at different temperatures were investigated. The mi- crostructure evolution was conducted using X-ray diffraction （XRD） and field emission scanning electronic microscopy （FESEM）. The hardness was measured by microhardness tester. The experimental results show that surface nanocrystrallization of AZ91D obtained by HESP would lead to the increase of microhardness. Low temperature heated at 100℃ for 1 h do not change the property obviously. However, both the microstructure and microhardness vary greatly after heat treatment at 400℃ for 1 h.展开更多
A nanostructured surface layer was fabricated on a AZ91D magnesium alloy by using a high-energy shot peening(HESP).HESP induced structure along the depth of the treated sample surface layer was characterized by means ...A nanostructured surface layer was fabricated on a AZ91D magnesium alloy by using a high-energy shot peening(HESP).HESP induced structure along the depth of the treated sample surface layer was characterized by means of X-ray diffractometer (XRD),transmission electron microscope(TEM) and high resolution transmission electron microscope(HRTEM).The experimental results show that a deformed layer of about 50 μm has formed after HESP treatment and the average grain size increases from about 40 nm in the surface layer to about 200 nm at the depth of 40 μm.The surface nanocrystallization can realize intercoordination of the dislocations slipping and dynamic recrystallization.The nanocrystalline grains have stacking faults and dislocation in their interiors.The microhardness of the top surface is about triplicate that of the coarse-grained matrix.展开更多
文摘Isothermal and isochronal annealing was conducted to study the thermal stability of the nanocrystalline in the surface layer of Mg alloy AZ91D induced by high-energy shot peening(HESP) .Field emission scanning electron microscope(FESEM) and X-ray diffractometer were used to characterize the microstructure.Results showed that nanocrystalline produced by HESP on the surface layer of the magnesium alloy AZ91D was 60-70 nm on average.The nanocrystalline could remain stable at about 100℃,and grew up slowly between 100℃ and 200℃.When the annealing temperature reached 300℃,the growth rate of the nanocrystalline increased significantly.The kinetic coefficient n of the nanocrystalline growth was calculated to be 2-3 and the grain growth activation energy Q=39.7 kJ/mol,far less than the self-diffusion activation energy of magnesium atoms in the coarse polycrystalline material.
基金Funded by the National Ministry of Education (No.207095)Beijing Key Laboratory for Corrosion Erosion and Surface Technology
文摘High-energy shot peening （HESP）, a method to produce severe plastic deformation by high velocity flying balls, was applied on die cast magnesium alloy AZ91D. Effects of surface nanocrystallization by HESP and heat treatment at different temperatures were investigated. The mi- crostructure evolution was conducted using X-ray diffraction （XRD） and field emission scanning electronic microscopy （FESEM）. The hardness was measured by microhardness tester. The experimental results show that surface nanocrystrallization of AZ91D obtained by HESP would lead to the increase of microhardness. Low temperature heated at 100℃ for 1 h do not change the property obviously. However, both the microstructure and microhardness vary greatly after heat treatment at 400℃ for 1 h.
基金Projects(50471070,50644041) supported by the National Natural Science Foundation of ChinaProject(20041023) supported by Youth Science and Technology Foundation of Shanxi Province, ChinaProject(200503005) supported by Key Laboratory Opening Foundation of Shanxi Province, China
文摘A nanostructured surface layer was fabricated on a AZ91D magnesium alloy by using a high-energy shot peening(HESP).HESP induced structure along the depth of the treated sample surface layer was characterized by means of X-ray diffractometer (XRD),transmission electron microscope(TEM) and high resolution transmission electron microscope(HRTEM).The experimental results show that a deformed layer of about 50 μm has formed after HESP treatment and the average grain size increases from about 40 nm in the surface layer to about 200 nm at the depth of 40 μm.The surface nanocrystallization can realize intercoordination of the dislocations slipping and dynamic recrystallization.The nanocrystalline grains have stacking faults and dislocation in their interiors.The microhardness of the top surface is about triplicate that of the coarse-grained matrix.
