HIL Simulation of a Mixed Islanded Power Network with External DSP Regulator

The present paper deals with the development of a modular, flexible and structured block to block approach for the study of regulators by implementing the different blocks on a DSP （digital signal processor）. The proposed low-cost approach has been applied and validated by the implementation of an industrial regulator in a real time hardware-in-the-loop simulation of a mixed islanded power network including precise models of the hydraulic system. The studied network is constituted of three different types of electrical power generation systems and a consumer.

Development of a Low-cost Hardware-in-the-loop Simulation System as a Test Bench for Anti-lock Braking System

Nowadays validation of anti-lock braking systems（ABS） relies mainly on a large amount of road tests.An alternative means with higher efficiency is employing the hardware-in-the-loop simulation（HILS） system to substitute part of road tests for designing,testing,and tuning electronic control units（ECUs） of ABS.Most HILS systems for ABS use expensive digital signal processor hardware and special purpose software,and some fail-safe functions with regard to wheel speeds cannot be evaluated since artificial wheel speed signals are usually provided.In this paper,a low-cost ABS HILS test bench is developed and used for validating the anti-lock braking performance and tuning control parameters of ABS controllers.Another important merit of the proposed test bench is that it can comprehensively evaluate the fail-safe functions with regard to wheel speed signals since real tone rings and sensors are integrated in the bench.A 5-DOF vehicle model with consideration of longitudinal load transfer is used to calculate tire forces,wheel speeds and vehicle speed.Each of the four real-time wheel speed signal generators consists of a servo motor plus a ring gear,which has sufficient dynamic response ability to emulate the rapid changes of the wheel speeds under strict braking conditions of very slippery roads.The simulation of braking tests under different road adhesion coefficients using the HILS test bench is run,and results show that it can evaluate the anti-lock braking performance of ABS and partly the fail-safe functions.This HILS system can also be used in such applications as durability test,benchmarking and comparison between different ECUs.The test bench developed not only has a relatively low cost,but also can be used to validate the wheel speed-related ECU design and all its fail-safe functions,and a rapid testing and proving platform with a high efficiency for research and development of the automotive ABS is therefore provided.

Hardware-in-the-Loop Simulation System for Space Manipulator Docking: Model,Stability and Experimental Evaluation

A manipulator-type docking hardware-in-the-loop(HIL)simulation system is proposed in this paper,with further development of the space docking technology and corresponding requirements of the engineering project.First,the structure of the manipulator-type HIL simulation system is explained.The mass and the flexibility of the manipulator has an important influence on the stability of the HIL system,which is the premise of accurately simulating actual space docking.Thus,the docking HIL simulation models of rigid,flexible and flexible-light space manipulators are established.The characteristics of the three HIL systems are studied from three important aspects:the system parameter configuration relation,the system stability condition and the dynamics frequency simulation ability.The key conclusions obtained were that the system satisfies stability or reproduction accuracy.Meanwhile,the influence of different manipulators on the system stability is further analyzed.The accuracy of the calculated results is verified experimentally.

Hardware-in-the-Loop Simulation of Vibration Control of Stay Cables with Damper Based on dSPACE System

A simple and economical method based on dSPACE system is developed to measure the effect of cable vibration control.The experiments,numerical simulation and hardware-in-the-loop(HIL)simulation are carried out for the vibration control of stay cables with dampers.Firstly,the test results of solid cable vibration under harmonic excitation are compared with the numerical simulation results of cable vibration to ensure the correctness of the simulation of cable module.Then,the vibration test results of solid cable with damper under harmonic excitation are compared with the numerical simulation results of solid cable with damper to ensure the correctness of the relevant modules.Finally,the external load and the cable are imported into the real-time simulation system to simulate the control effect of the damper under the current excitation in real time.The results show that the simulation is correct and the HIL simulation is feasible in the bridge engineering.

激光制导武器半实物仿真系统的设计与实现

首先,以某激光制导弹药为背景,提出了室内半实物仿真系统的总体设计方案,介绍了一种激光半主动导引头的工作原理。其次,在室内局限环境下,建立了弹目几何关系的数学模型,研究了导引头入瞳光学特性,并根据制导与控制系统的工作原理,设计了末制导段弹道的半实物仿真模型。最后,设置两种末端制导的初始条件,引入导引头和角速率陀螺等弹上部件进行多次弹道仿真试验。试验结果表明,基于该导引头和角速率陀螺的制导与控制系统设计合理,可以实现精确打击。

MODEL REFERENCE ADAPTIVE CONTROL BASED ON NONLINEAR COMPENSATION FOR TURBOFAN ENGINE

The design of a turbofan rotor speed control system, using model reference adaptive control（MRAC） method with input and output measurements, is discussed for the purpose of practical application. The nonlinear compensator based on functional link neural network is used to deal with the engine nonlinearity and the hardware-in-loop simulation is also developed. The results show that the nonlinear MRAC controller has the adequate performance of compensating and adapting nonlinearity arising from the change of engine state or working environment. Such feature demonstrates potential practical applications of MRAC for aeroengine control system.

基于硬件在环仿真系统的整车经济性仿真

硬件在环仿真系统已经成为发动机控制器开发过程中非常重要的工具和平台,对于提高控制器开发效率发挥着重要的作用。分析某发动机硬件在环仿真台架结构及如何使用仿真台架进行整车发动机经济性仿真计算,并通过实例体现硬件在环仿真系统在汽车整车经济性仿真的应用及相比传统实体台架的优势。

FPGA-based hardware-in-the-loop for multi-domain simulation

In this paper,we present a new approach for complex system design,which allows rapid,efficient and low-cost prototyping.This approach can simplify designing tasks and go faster from system modeling to effective hardware implementation.Designing multi-domain systems requires different engineering competences and several tools,our approach gives a unique design environment,based on the use of VHDL-AMS modeling language and FPGA device within the same design tool.This approach is intended to enhance hardware-in-the-loop(HIL)practices with a more realistic simulation which improve the verification process in the system design flow.This paper describes the implementation of a software/hardware platform as a practical support for our approach,the feasibility and the benefits of this approach are demonstrated through a practical case study for power converter control.The obtained results show that the developed method achieves significant speed-up compared with conventional simulation,with a minimum used resources and minimum latency.

An experimental study of the dual-loop control of electro-hydraulic load simulator (EHLS)

This paper investigates motion coupling disturbance（the so called surplus torque）in the hardware-in-the-loop（HIL）experiments.The＇＇velocity synchronization scheme＇＇was proposed by Jiao for an electro-hydraulic load simulator（EHLS）in 2004.In some situations,however,the scheme is limited in the implementation for certain reasons,as is the case when the actuator＇s valve signal is not available or it is seriously polluted by noise.To solve these problems,a＇＇dual-loop scheme＇＇is developed for EHLS.The dual-loop scheme is a combination of a torque loop and a position synchronization loop.The role of the position synchronization loop is to decouple the motion disturbance caused by the actuator system.To verify the feasibility and effectiveness of the proposed scheme,extensive simulations are performed using AMESim.Then,the performance of the developed method is validated by experiments.