The existence of a significant electron drift instability(EDI) in the Hall thruster is considered as one of the possible causes of the abnormal increase in axial electron mobility near the outlet of the channel. In re...The existence of a significant electron drift instability(EDI) in the Hall thruster is considered as one of the possible causes of the abnormal increase in axial electron mobility near the outlet of the channel. In recent years, extensive simulation research on the characteristics of EDI has been conducted, but the excitation mechanism and growth mechanism of EDI in linear stage and nonlinear stage remain unclear. In this work, a one-dimensional PIC model in the azimuthal direction of the thruster near-exit region is established to gain further insights into the mechanism of the EDI in detail, and the effects of different types of propellants on EDI characteristics are discussed. The changes in axial electron transport caused by EDI under different types of propellants and electromagnetic field strengths are also examined. The results indicate that EDI undergoes a short linear growth phase before transitioning to the nonlinear phase and finally reaching saturation through the ion Landau damping. The EDI drives a significant ion heating in the azimuthal direction through electron–ion friction before entering the quasi-steady state, which increases the axial mobility of the electrons. Using lighter atomic weight propellant can effectively suppress the oscillation amplitude of EDI, but it will increase the linear growth rate, frequency, and phase velocity of EDI. Compared with the classical mobility, the axial electron mobility under the EDI increases by three orders of magnitude, which is consistent with experimental phenomena. The change of propellant type is insufficient to significantly change the axial electron mobility. It is also found that the collisions between electrons and neutral gasescan significantly affect the axial electron mobility under the influence of EDI, and lead the strength of the electric field to increase and the strength of the magnetic field to decrease, thereby both effectively suppressing the axial transport of electrons.展开更多
Previous studies have shown that there is an obvious coupling relationship between the installation location of the external cathode and the magnetic separatrix in the plume region of a Hall thruster.In this paper,the...Previous studies have shown that there is an obvious coupling relationship between the installation location of the external cathode and the magnetic separatrix in the plume region of a Hall thruster.In this paper,the particle-in-cell simulation method is used to compare the thruster discharge process under the conditions of different position relationships between the cathode and the magnetic separatrix.By comparing the distribution of electron conduction,potential,plasma density and other microscopic parameters,we try to explain the formation mechanism of the discharge difference.The simulation results show that the cathode inside and outside the magnetic separatrix has a significant effect on the distribution of potential and plasma density.When the cathode is located on the outer side of the magnetic separatrix,the potential above the plume region is relatively low,and there is a strong potential gradient above the plume region.This potential gradient is more conducive to the radial diffusion of ions above the plume,which is the main reason for the strong divergence of the plume.The distribution of ion density is also consistent with the distribution of potential.When the cathode is located on the outer side of the magnetic separatrix,the radial diffusion of ions in the plume region is enhanced.Meanwhile,by comparing the results of electron conduction,it is found that the traiectories of electrons emitted from the cathode are significantly different between the inner and outer sides of the magnetic separatrix.This is mainly because the electrons are affected by the magnetic mirror effect of the magnetic tip,which makes it difficult for the electrons to move across the magnetic separatrix.This is the main reason for the difference in potential distribution.In this paper,the simulation results of macroscopic parameters under several conditions are also compared,and they are consistent with the experimental results.The cathode is located on the inner side of the magnetic separatrix,which can effectively reduce the plume divergence angle and improve the thrust.In this paper,the cathode moves from R=50 mm to R=35 mm along the radial direction,the thrust increases by 3.6 mN and the plume divergence angle decreases by 23.77%.Combined with the comparison of the ionization region and the peak ion density,it is found that the main reason for the change in thrust is the change in the radial diffusion of ions in the plume region.展开更多
Low-power Hall thruster(LHT) generally has poor discharge efficiency characteristics due to the large surface-to-volume ratio.Aiming to further refine and improve the performance of 300 W class LHT in terms of thrust ...Low-power Hall thruster(LHT) generally has poor discharge efficiency characteristics due to the large surface-to-volume ratio.Aiming to further refine and improve the performance of 300 W class LHT in terms of thrust and efficiency,and to obtain the most optimal operating point,the experimental study of the discharge characteristics for three different anode positions was conducted under the operation of various discharge voltages(100-400 V) and anode mass flow rates(0.65 mg·s-1and 0.95 mg·s-1).The experimental results indicated that the thruster has the most excellent performance in terms of thrust and efficiency etc at a channel length of 27 mm for identical operating conditions.In addition,particle in cell simulations,employed to reveal the underlying physical mechanisms,show that the ionization and acceleration zone is pushed downwards towards the channel exit as the anode moves towards the exit.At the identical operating point,when the channel length is reduced from 32 to 27 mm,the ionization and acceleration zone moves towards the exit,and the parameters such as thrust and efficiency increase due to the high ionization rate,ion number density,and axial electric field.When the channel length is further moved to 24 mm,the parameters in terms of thrust(F) and efficiency(ηa) are reduced as a result of the decreasing ionization efficiency(ηm) and the larger plume divergence angle(α).In this paper,the results indicated that an optimum anode position(ΔL=27 mm) exists for the optimum performance.展开更多
A two-and three-dimensional velocity space axisymmetric hybrid-PIC model of Hall thruster discharge called Hybrid2D has been developed.The particle-in-cell(PIC) method was used for neutrals and ions(heavy species),and...A two-and three-dimensional velocity space axisymmetric hybrid-PIC model of Hall thruster discharge called Hybrid2D has been developed.The particle-in-cell(PIC) method was used for neutrals and ions(heavy species),and fluid dynamics on a magnetic field-aligned(MFA) mesh was used for electrons.A time-saving method for heavy species moment interpolation on a MFA mesh was developed.The method comprises using regular rectangle and irregular triangle meshes,connected to each other on a pre-processing stage.The electron fluid model takes into account neither inertia terms nor viscous terms and includes an electron temperature equation with a heat flux term.The developed model was used to calculate all heavy species moments up to the third one in a stationary case.The analysis of the viscosity and the heat flux impact on the force and energy balance has shown that for the calculated geometry of the Hall thruster,the viscosity and the heat flux terms have the same magnitude as the other terms and could not be omitted.Also,it was shown that the heat flux is not proportional to the temperature gradient and,consequently,the highest moments should be calculated to close the neutral fluid equation system.At the same time,ions can only be modeled as a cold non-viscous fluid when the sole aim of modeling is the calculation of the operating parameters or distribution of the local parameters along the centerline of the discharge channel.This is because the magnitude of the viscosity and the temperature gradient terms are negligible at the centerline.However,when a simulation’s focus is either on the radial divergence of the plume or on magnetic pole erosion,three components of the ion temperature should be taken into consideration.The non-diagonal terms of ion pressure tensor have a lower impact than the diagonal terms.According to the study,a zero heat flux condition could be used to close the ion equation system in calculated geometry.展开更多
The accurate knowledge of the thrust vector eccentricity and beam divergence characteristics of Hall thrusters are of significant engineering value for the beneficial integration and successful application of Hall thr...The accurate knowledge of the thrust vector eccentricity and beam divergence characteristics of Hall thrusters are of significant engineering value for the beneficial integration and successful application of Hall thrusters on spacecraft.For the characteristics of the plume bipolar diffusion due to the annular discharge channel of the Hall thruster,a Gaussian-fitted method for thrust vector deviation angle and beam divergence of Hall thrusters based on dual Faraday probe array planes was proposed in respect of the Hall thruster beam characteristics.The results show that the ratios of the deviation between the maximum and minimum values of the beam divergence angle and the thrust vector eccentricity angle using a Gaussian fit to the optimized Faraday probe dual plane to the mean value are 1.4%and 11.5%,respectively.The optimized thrust vector eccentricity angle obtained has been substantially improved,by approximately 20%.The beam divergence angle calculated using a Gaussian fitting to the optimized Faraday probe dual plane is approximately identical to the non-optimized one.The beam divergence and thrust vector eccentricity angles for different anode mass flow rates were obtained by averaging the beam divergence and thrust vector eccentricity angles calculated by the dual-plane,Gaussian-fitted ion current density method for different cross-sections.The study not only allows for an immediate and effective tool for determining the design of thrust vector adjustment mechanisms of spacecraft with different power Hall thrusters but also for characterizing the 3D spatial distribution of the Hall thruster plume.展开更多
In this work,we have carried out a simulation study on the discharge process of Hall thrusters under the conditions of different neutral gas radial supply positions based on the particle-in-cell(PIC)and Monte Carlo co...In this work,we have carried out a simulation study on the discharge process of Hall thrusters under the conditions of different neutral gas radial supply positions based on the particle-in-cell(PIC)and Monte Carlo collision(MCC)methods.This paper compares the two-dimensional(2D)distributions of neutral gas,plasma and wall erosion-related parameters under different neutral gas supply positions.The comparison results show that the change of the neutral gas supply position affects the radial distribution uniformity of the neutral gas and plasma in the channel.From the comparison of the density peaks,it can be found that the neutral gas density and the plasma density peak under the upper gas supply condition are relatively low,and the plasma density peak is 22.49%lower than the density peak under the middle gas supply condition.Meanwhile,as the radial position of the gas supply moves from the lower gas supply to the upper gas supply,the position of the ionization zone also gradually moves toward the anode.The results of erosion-related parameter distribution comparison show that the change of gas supply location has an obvious influence on erosion rate and erosion range.In terms of erosion rate,the wall erosion rate is relatively low under the upper gas supply condition,and the peak erosion rates of the inner and outer walls are 33.3%and 29.9%lower than those under the other two conditions.In terms of erosion range,as the gas supply position moves from the lower gas supply position to the upper gas supply position,the erosion range gradually increases from5 to 7.5 mm.展开更多
Hall thruster has the advantages of simple structure, high specific impulse, high efficiency, and long service life, and so on. It is suitable for spacecraft attitude control, North and South position keeping, and oth...Hall thruster has the advantages of simple structure, high specific impulse, high efficiency, and long service life, and so on. It is suitable for spacecraft attitude control, North and South position keeping, and other track tasks. The anode layer Hall thruster is a kind of Hall thruster. The thruster has a longer anode area and a relatively short discharge channel. In this paper, the effect of the channel length on the performance of the anode layer Hall thruster is simulated by the PIC simulation method. The simulation results show that the change of the channel length has significant effect on the plasma parameters, such as potential and plasma density and so on. The ionization region mainly concentrates at the hollow anode outlet position, and can gradually move toward the channel outlet as the channel length decreases. The collision between the ions and the wall increases with the channel length increasing. So the proper shortening of the channel length can increase the life of the thruster. Besides, the results show that there is a best choice of the channel length for obtaining the best performance. In this paper, thruster has the best performance under a channel length of 5 mm.展开更多
The highest deposition of power and temperature is always near the cusp of the ATON-type Hall thruster.This shows that when there are electrons gathering at the cusp,the distribution of heat load will be uniform,which...The highest deposition of power and temperature is always near the cusp of the ATON-type Hall thruster.This shows that when there are electrons gathering at the cusp,the distribution of heat load will be uniform,which will potentially damage the reliability.Therefore,we optimize the magnetic field near the anode.We changed the magnetic field characteristics in the near-anode region with an additional magnetic screen,and performed numerical simulation with particle-incell simulation.The simulation results show that the magnetic field of the thruster with the additional magnetic screen can alleviate the over-concentration of power deposition on the anode and reduce the power deposition in the anode by 20%,while ensuring that the overall magnetic field characteristics do not change significantly.展开更多
Numerical simulation of the effect of the anode magnetic shielding on the magnetic field and ion beam in a cylindrical Hall thruster is presented. The results show that after the anode is shielded by the magnetic shie...Numerical simulation of the effect of the anode magnetic shielding on the magnetic field and ion beam in a cylindrical Hall thruster is presented. The results show that after the anode is shielded by the magnetic shield, the magnetic field lines near the anode surface are obviously convex curved, the ratio of the magnetic mirror is enhanced, the width of the positive magnetic field gradient becomes larger than that without the anode magnetic shielding, the radial magnetic field component is enhanced, and the discharge plasma turbulence is reduced as a result of keeping the original saddle field profile and the important role the other two saddle field profiles play in restricting electrons. The results of the particle in cell (PIC) numerical simulation show that both the ion number and the energy of the ion beam increase after the anode is shielded by the magnetic shield. In other words, the specific impulse of the cylindrical Hall thruster is enhanced.展开更多
Experimental investigations into the effects of the magnetic field configuration near the channel exit on the plume of Hall thrusters were conducted. The magnetic field configuration near the channel exit is character...Experimental investigations into the effects of the magnetic field configuration near the channel exit on the plume of Hall thrusters were conducted. The magnetic field configuration near the channel exit is characterized by the inclination angle between the magnetic field lines and the thruster radial direction. Different inclination angles were obtained by varying the current ratio in the coils. The plume divergence angles were measured by a dual-directed probe. The results showed that the plume divergence angle increased obviously with the increase in the magnitude of the inclination angle near the channel exit. Therefore, in order to optimize the magnetic field for reducing plume divergence, the magnitude of the inclination angle should be reduced as much as possible. It suggests that the magnetic field configuration near the channel exit is another important factor that affects plume divergence.展开更多
The influences of the low-emissive graphite segmented electrode t)laeed near the channel exit on the discharge characteristics of a Hall thruster are studied using the particle- in-cell method. A two-dimensional phys...The influences of the low-emissive graphite segmented electrode t)laeed near the channel exit on the discharge characteristics of a Hall thruster are studied using the particle- in-cell method. A two-dimensional physical model is established according to the Hall thruster discharge channel configuration. The effects of electrode length on the potential, ion density, electron temperature, ionization rate and discharge current are investigated. It is found that, with tile increasing of the segmented electrode length, the equipotential lines bend towards the channel exit. and approximately parallel to the wall at the channel surface, the radial velocity and radial flow of ions are increased, and the electron temperature is also enhanced. Due to the conductive characteristic of electrodes, the radial electric field and the axial electron conductivity near the wall are enhanced, and the probability of the electron-atom ionization is reduced, which leads to the degradation of the ionization rate in the discharge channel. However, the interaction between electrons and the wall enhances the near wall conductivity, therefore the discharge current grows along with the segmented electrode length, and the performance of the thruster is also affected.展开更多
In this paper, we summarize the research development of low-frequency oscillations in the last few decades. The findings of physical mechanism, characteristics and stabilizing methods of low-frequency oscillations are...In this paper, we summarize the research development of low-frequency oscillations in the last few decades. The findings of physical mechanism, characteristics and stabilizing methods of low-frequency oscillations are discussed. It shows that it is unreasonable and incomplete to model an ionization region separately to analyze the physical mechanism of low-frequency oscillations. Electro-dynamics as well as the formation conditions of ionization distribution play an important role in characteristics and stabilizing of low-frequency oscillations. Understanding the physical mechanism and characteristics of low- frequency oscillations thoroughly and developing a feasible method stabilizing this instability are still important research subjects.展开更多
A discharge channel with a chamfered wall not only has application in the design of modern Hall thrusters, but also exists where the channel wall is eroded, and so is a common status for these units. In this paper, th...A discharge channel with a chamfered wall not only has application in the design of modern Hall thrusters, but also exists where the channel wall is eroded, and so is a common status for these units. In this paper, the laws and mechanisms that govern the effect of the chamfered wall on the performance of a Hall thruster are investigated. By applying both experimental measurement and particle-in-cell simulation, it is determined that there is a moderate chamfer angle that can further improve the optimal performance obtained with a straight channel. This is because the chamfering of the wall near the channel exit can enhance ion acceleration and effectively reduce ion recombination on the wall, which is favorable to the promotion of the thrust and efficiency. However, the chamfer angle should not be too large; otherwise, both the density of the propellant gas and the distribution of the plasma potential in the channel are influenced, which is undesirable for efficient propellant utilization and beam concentration. Therefore, it is suggested that the chamfer shape of the channel wall is an important factor that must be carefully considered in the design of Hall thrusters.展开更多
Considering the actual magnetic field configuration in a Hall thruster, the effect of magnetic mirror on the radial profile of near-wall conductivity (NWC) is studied in this paper. The plasma electron dynamic proce...Considering the actual magnetic field configuration in a Hall thruster, the effect of magnetic mirror on the radial profile of near-wall conductivity (NWC) is studied in this paper. The plasma electron dynamic process is described by the test particle method. The Monte Carlo scheme is used to solve this model. The radial profile of electron mobility is obtained and the role of magnetic mirror in NWC is analysed both theoretically and numerically. The numerical results show that the electron mobility peak due to NWC is inversely proportional to the magnetic mirror ratio and the asymmetry of electron mobility along the radial direction gets greater when the magnetic mirror is considered. This effect indicates that apart from the disparity in the magnetic field strength, the difference in the magnetic mirror ratio near the inner and outer walls would actually augment the asymmetry of the radial profile of NWC in Hall thrusters.展开更多
In this paper, a direct connection between the discharge current amplitude and the thruster performance is established by varying solely the capacitance of the filter unit of the Hall thrusters. To be precise, the var...In this paper, a direct connection between the discharge current amplitude and the thruster performance is established by varying solely the capacitance of the filter unit of the Hall thrusters. To be precise, the variation characteristics of ion current, propellant utilization efficiency, and divergence angle of plume at different low-frequency oscillation amplitudes are measured. The findings demonstrate that in the case of the propellant in the discharge channel just meets or falls below the full ionization condition, the increase of low-frequency oscillation amplitude can significantly enhance the ionization degree of the neutral gas in the channel and increase the thrust and anode efficiency of thruster. On the contrary, the increase in the amplitude of low-frequency oscillation will lead to increase the loss of plume divergence, therefore the thrust and anode efficiency of thruster decrease.展开更多
In this study,the neutral gas distribution and steady-state discharge under different discharge channel lengths were studied via numerical simulations.The results show that the channel with a length of 22 mm has the a...In this study,the neutral gas distribution and steady-state discharge under different discharge channel lengths were studied via numerical simulations.The results show that the channel with a length of 22 mm has the advantage of comprehensive discharge performance.At this time,the magnetic field intensity at the anode surface is 10%of the peak magnetic field intensity.Further analysis shows that the high-gas-density zone moves outward due to the shortening of the channel length,which optimizes the matching between the gas flow field and the magnetic field,and thus increases the ionization rate.The outward movement of the main ionization zone also reduces the ion loss on the wall surface.Thus,the propellant utilization efficiency can reach a maximum of 96.8%.Moreover,the plasma potential in the main ionization zone will decrease with the shortening of the channel.The excessively short-channel will greatly reduce the voltage utilization efficiency.The thrust is reduced to a minimum of 46.1 m N.Meanwhile,because the anode surface is excessively close to the main ionization zone,the discharge reliability is also difficult to guarantee.It was proved that the performance of Hall thrusters can be optimized by shortening the discharge channel appropriately,and the specific design scheme of short-channel of HEP-1350 PM was defined,which serves as a reference for the optimization design of Hall thruster with large height–radius ratio.The shortchannel design also helps to reduce the thruster axial dimension,further consolidating the advantages of lightweight and large thrust-to-weight ratio of the Hall thruster with large height–radius ratio.展开更多
In order to investigate the effects of secondary electrons, which are emitted from the wall, on the performance of a thruster, a one-dimensional fluid model of the plasma sheath in double walls is applied to study the...In order to investigate the effects of secondary electrons, which are emitted from the wall, on the performance of a thruster, a one-dimensional fluid model of the plasma sheath in double walls is applied to study the characteristics of a magnetized sheath. The effects of secondary electron emission (SEE) coefficients and trapping coefficients, as well as magnetic field, on the structure of the plasma sheath are investigated. The results show that sheath potential and wall potential rise with the increment of SEE coefficient and trapping coefficient which results in a reduced sheath thickness. In addition, magnetic field strength will influence the sheath potential distributions.展开更多
The cylindrical Hall thruster has the good prospect of serving as a miniaturized electric propulsion device.A 2 D-3 V particle-in-cell plus Monte Carlo(PIC-MCC) method is used to study the effect of the magnetic cus...The cylindrical Hall thruster has the good prospect of serving as a miniaturized electric propulsion device.A 2 D-3 V particle-in-cell plus Monte Carlo(PIC-MCC) method is used to study the effect of the magnetic cusp on discharge characteristics of a cylindrical Hall thruster.The simulation results show that the main ionization region and the main potential drop of the thruster are located at the upstream of the discharge channel.When the magnetic cusp moves toward the anode side,the main ionization region is compressed and weakened,moving upstream correspondingly.The ionization near the cusp is enhanced,and the interaction between the plasma and the wall increases.The simulation results suggest that the magnetic cusp should be located near the channel exit.展开更多
To achieve a better insight into the far-field plasma spatial distribution and evolution characteristics of the 300 W class low-power Hall thruster(LHT)for commercial aerospace applications,a dedicated and integrated ...To achieve a better insight into the far-field plasma spatial distribution and evolution characteristics of the 300 W class low-power Hall thruster(LHT)for commercial aerospace applications,a dedicated and integrated plasma diagnostic system composed of seventeen Faraday cups(FC)and two triple Langmuir probes(TLP)is established to investigate the timeaveraged in situ spatial distribution characteristics of far-field ions and electrons.The ion current density(ICD),plasma potential,plasma density,and electron temperature at 1000 mm downstream of 300 W class LHT for commercial aerospace applications in the azimuthal angle range of-90°to 90°were investigated under the conditions of different anode mass flow rates and discharge voltages.The results demonstrated that ICD,beam divergence angle,and mass utilization efficiency increased with increasing anode mass rate.The double-wings phenomenon was observed in the spatial distribution of ICD at large angles from the thruster axis,which is attributed to charge exchange collisions at increasing vacuum backpressure.The plasma electron temperature,electron density,and plasma potential parameters derived from the TLP decreased rapidly in the angle range from 0°to 30°and did not exhibit significant variations above 30°,which was also in good agreement with the results of the measured divergence angle of the FC.The discrepancy of average ion speed was calculated.The maximum error is better than 31.5%which checks the consistency between the TLP’s results and that of FC to some extent.展开更多
The intersection point of the characteristic magnetic field line(CMFL) crossing the anode boundary with the discharge channel wall, and its influence on thruster performance and the energy and flux of ions bombardin...The intersection point of the characteristic magnetic field line(CMFL) crossing the anode boundary with the discharge channel wall, and its influence on thruster performance and the energy and flux of ions bombarding the channel wall, have been studied numerically. The simulation results demonstrate that with the increase in distance from the crossover point of the CMFL with the channel wall to the bottom of the thruster channel, the ionization rate in the discharge channel gradually increases; meanwhile, the ion energy and ion current density bombarding the channel wall decreases. When the point of the CMFL with the channel wall is at the channel outlet, the thrust, specific impulse, and efficiency are at a maximum, while the ion energy and ion current density bombarding the channel wall are at a minimum. Therefore, to improve the performance and lifetime of the thruster, it is important to control the point of intersection of the CMFL with the channel wall.展开更多
基金Project supported by the National Natural Science Foundation of China (Grant Nos.11975062 and 11605021)the Fundamental Research Funds for the Central Universities (Grant No.3132023192)。
文摘The existence of a significant electron drift instability(EDI) in the Hall thruster is considered as one of the possible causes of the abnormal increase in axial electron mobility near the outlet of the channel. In recent years, extensive simulation research on the characteristics of EDI has been conducted, but the excitation mechanism and growth mechanism of EDI in linear stage and nonlinear stage remain unclear. In this work, a one-dimensional PIC model in the azimuthal direction of the thruster near-exit region is established to gain further insights into the mechanism of the EDI in detail, and the effects of different types of propellants on EDI characteristics are discussed. The changes in axial electron transport caused by EDI under different types of propellants and electromagnetic field strengths are also examined. The results indicate that EDI undergoes a short linear growth phase before transitioning to the nonlinear phase and finally reaching saturation through the ion Landau damping. The EDI drives a significant ion heating in the azimuthal direction through electron–ion friction before entering the quasi-steady state, which increases the axial mobility of the electrons. Using lighter atomic weight propellant can effectively suppress the oscillation amplitude of EDI, but it will increase the linear growth rate, frequency, and phase velocity of EDI. Compared with the classical mobility, the axial electron mobility under the EDI increases by three orders of magnitude, which is consistent with experimental phenomena. The change of propellant type is insufficient to significantly change the axial electron mobility. It is also found that the collisions between electrons and neutral gasescan significantly affect the axial electron mobility under the influence of EDI, and lead the strength of the electric field to increase and the strength of the magnetic field to decrease, thereby both effectively suppressing the axial transport of electrons.
基金supported by the Shanghai 2022 Science and Technology Innovation Action Plan(No.22YF1446800)。
文摘Previous studies have shown that there is an obvious coupling relationship between the installation location of the external cathode and the magnetic separatrix in the plume region of a Hall thruster.In this paper,the particle-in-cell simulation method is used to compare the thruster discharge process under the conditions of different position relationships between the cathode and the magnetic separatrix.By comparing the distribution of electron conduction,potential,plasma density and other microscopic parameters,we try to explain the formation mechanism of the discharge difference.The simulation results show that the cathode inside and outside the magnetic separatrix has a significant effect on the distribution of potential and plasma density.When the cathode is located on the outer side of the magnetic separatrix,the potential above the plume region is relatively low,and there is a strong potential gradient above the plume region.This potential gradient is more conducive to the radial diffusion of ions above the plume,which is the main reason for the strong divergence of the plume.The distribution of ion density is also consistent with the distribution of potential.When the cathode is located on the outer side of the magnetic separatrix,the radial diffusion of ions in the plume region is enhanced.Meanwhile,by comparing the results of electron conduction,it is found that the traiectories of electrons emitted from the cathode are significantly different between the inner and outer sides of the magnetic separatrix.This is mainly because the electrons are affected by the magnetic mirror effect of the magnetic tip,which makes it difficult for the electrons to move across the magnetic separatrix.This is the main reason for the difference in potential distribution.In this paper,the simulation results of macroscopic parameters under several conditions are also compared,and they are consistent with the experimental results.The cathode is located on the inner side of the magnetic separatrix,which can effectively reduce the plume divergence angle and improve the thrust.In this paper,the cathode moves from R=50 mm to R=35 mm along the radial direction,the thrust increases by 3.6 mN and the plume divergence angle decreases by 23.77%.Combined with the comparison of the ionization region and the peak ion density,it is found that the main reason for the change in thrust is the change in the radial diffusion of ions in the plume region.
基金National Natural Science Foundation of China (No.12005087)Science and Technology Program of Gansu Province (Nos.2006ZCTF0054, HTKJ2019KL510003,and 20JR10RA478)。
文摘Low-power Hall thruster(LHT) generally has poor discharge efficiency characteristics due to the large surface-to-volume ratio.Aiming to further refine and improve the performance of 300 W class LHT in terms of thrust and efficiency,and to obtain the most optimal operating point,the experimental study of the discharge characteristics for three different anode positions was conducted under the operation of various discharge voltages(100-400 V) and anode mass flow rates(0.65 mg·s-1and 0.95 mg·s-1).The experimental results indicated that the thruster has the most excellent performance in terms of thrust and efficiency etc at a channel length of 27 mm for identical operating conditions.In addition,particle in cell simulations,employed to reveal the underlying physical mechanisms,show that the ionization and acceleration zone is pushed downwards towards the channel exit as the anode moves towards the exit.At the identical operating point,when the channel length is reduced from 32 to 27 mm,the ionization and acceleration zone moves towards the exit,and the parameters such as thrust and efficiency increase due to the high ionization rate,ion number density,and axial electric field.When the channel length is further moved to 24 mm,the parameters in terms of thrust(F) and efficiency(ηa) are reduced as a result of the decreasing ionization efficiency(ηm) and the larger plume divergence angle(α).In this paper,the results indicated that an optimum anode position(ΔL=27 mm) exists for the optimum performance.
文摘A two-and three-dimensional velocity space axisymmetric hybrid-PIC model of Hall thruster discharge called Hybrid2D has been developed.The particle-in-cell(PIC) method was used for neutrals and ions(heavy species),and fluid dynamics on a magnetic field-aligned(MFA) mesh was used for electrons.A time-saving method for heavy species moment interpolation on a MFA mesh was developed.The method comprises using regular rectangle and irregular triangle meshes,connected to each other on a pre-processing stage.The electron fluid model takes into account neither inertia terms nor viscous terms and includes an electron temperature equation with a heat flux term.The developed model was used to calculate all heavy species moments up to the third one in a stationary case.The analysis of the viscosity and the heat flux impact on the force and energy balance has shown that for the calculated geometry of the Hall thruster,the viscosity and the heat flux terms have the same magnitude as the other terms and could not be omitted.Also,it was shown that the heat flux is not proportional to the temperature gradient and,consequently,the highest moments should be calculated to close the neutral fluid equation system.At the same time,ions can only be modeled as a cold non-viscous fluid when the sole aim of modeling is the calculation of the operating parameters or distribution of the local parameters along the centerline of the discharge channel.This is because the magnitude of the viscosity and the temperature gradient terms are negligible at the centerline.However,when a simulation’s focus is either on the radial divergence of the plume or on magnetic pole erosion,three components of the ion temperature should be taken into consideration.The non-diagonal terms of ion pressure tensor have a lower impact than the diagonal terms.According to the study,a zero heat flux condition could be used to close the ion equation system in calculated geometry.
基金the Key Laboratory Funds for Science and Technology on Vacuum Technology and Physics Laboratory(No.HTKJ2022KL510002)the Military Test Instruments Program(No.2006ZCTF0054)。
文摘The accurate knowledge of the thrust vector eccentricity and beam divergence characteristics of Hall thrusters are of significant engineering value for the beneficial integration and successful application of Hall thrusters on spacecraft.For the characteristics of the plume bipolar diffusion due to the annular discharge channel of the Hall thruster,a Gaussian-fitted method for thrust vector deviation angle and beam divergence of Hall thrusters based on dual Faraday probe array planes was proposed in respect of the Hall thruster beam characteristics.The results show that the ratios of the deviation between the maximum and minimum values of the beam divergence angle and the thrust vector eccentricity angle using a Gaussian fit to the optimized Faraday probe dual plane to the mean value are 1.4%and 11.5%,respectively.The optimized thrust vector eccentricity angle obtained has been substantially improved,by approximately 20%.The beam divergence angle calculated using a Gaussian fitting to the optimized Faraday probe dual plane is approximately identical to the non-optimized one.The beam divergence and thrust vector eccentricity angles for different anode mass flow rates were obtained by averaging the beam divergence and thrust vector eccentricity angles calculated by the dual-plane,Gaussian-fitted ion current density method for different cross-sections.The study not only allows for an immediate and effective tool for determining the design of thrust vector adjustment mechanisms of spacecraft with different power Hall thrusters but also for characterizing the 3D spatial distribution of the Hall thruster plume.
文摘In this work,we have carried out a simulation study on the discharge process of Hall thrusters under the conditions of different neutral gas radial supply positions based on the particle-in-cell(PIC)and Monte Carlo collision(MCC)methods.This paper compares the two-dimensional(2D)distributions of neutral gas,plasma and wall erosion-related parameters under different neutral gas supply positions.The comparison results show that the change of the neutral gas supply position affects the radial distribution uniformity of the neutral gas and plasma in the channel.From the comparison of the density peaks,it can be found that the neutral gas density and the plasma density peak under the upper gas supply condition are relatively low,and the plasma density peak is 22.49%lower than the density peak under the middle gas supply condition.Meanwhile,as the radial position of the gas supply moves from the lower gas supply to the upper gas supply,the position of the ionization zone also gradually moves toward the anode.The results of erosion-related parameter distribution comparison show that the change of gas supply location has an obvious influence on erosion rate and erosion range.In terms of erosion rate,the wall erosion rate is relatively low under the upper gas supply condition,and the peak erosion rates of the inner and outer walls are 33.3%and 29.9%lower than those under the other two conditions.In terms of erosion range,as the gas supply position moves from the lower gas supply position to the upper gas supply position,the erosion range gradually increases from5 to 7.5 mm.
文摘Hall thruster has the advantages of simple structure, high specific impulse, high efficiency, and long service life, and so on. It is suitable for spacecraft attitude control, North and South position keeping, and other track tasks. The anode layer Hall thruster is a kind of Hall thruster. The thruster has a longer anode area and a relatively short discharge channel. In this paper, the effect of the channel length on the performance of the anode layer Hall thruster is simulated by the PIC simulation method. The simulation results show that the change of the channel length has significant effect on the plasma parameters, such as potential and plasma density and so on. The ionization region mainly concentrates at the hollow anode outlet position, and can gradually move toward the channel outlet as the channel length decreases. The collision between the ions and the wall increases with the channel length increasing. So the proper shortening of the channel length can increase the life of the thruster. Besides, the results show that there is a best choice of the channel length for obtaining the best performance. In this paper, thruster has the best performance under a channel length of 5 mm.
基金the financial support from National Natural Science Foundation of China (Nos. 51777045, 51736003)supply of the Hunan Science and Technology Innovation Project (No. 2019RS1102)supply of the Shenzhen Technology Projects (No. JCYJ20170307151117299)。
文摘The highest deposition of power and temperature is always near the cusp of the ATON-type Hall thruster.This shows that when there are electrons gathering at the cusp,the distribution of heat load will be uniform,which will potentially damage the reliability.Therefore,we optimize the magnetic field near the anode.We changed the magnetic field characteristics in the near-anode region with an additional magnetic screen,and performed numerical simulation with particle-incell simulation.The simulation results show that the magnetic field of the thruster with the additional magnetic screen can alleviate the over-concentration of power deposition on the anode and reduce the power deposition in the anode by 20%,while ensuring that the overall magnetic field characteristics do not change significantly.
基金supported by National Natural Science Foundation of China (No. 10675040)College Scientific Research and Development Fund (No. C122009015) of China
文摘Numerical simulation of the effect of the anode magnetic shielding on the magnetic field and ion beam in a cylindrical Hall thruster is presented. The results show that after the anode is shielded by the magnetic shield, the magnetic field lines near the anode surface are obviously convex curved, the ratio of the magnetic mirror is enhanced, the width of the positive magnetic field gradient becomes larger than that without the anode magnetic shielding, the radial magnetic field component is enhanced, and the discharge plasma turbulence is reduced as a result of keeping the original saddle field profile and the important role the other two saddle field profiles play in restricting electrons. The results of the particle in cell (PIC) numerical simulation show that both the ion number and the energy of the ion beam increase after the anode is shielded by the magnetic shield. In other words, the specific impulse of the cylindrical Hall thruster is enhanced.
基金supported by National Natural Science Foundation of China(No.50676026)the Program for Chair Professors of"Cheung Kong Scholars Program"of China in 2008
文摘Experimental investigations into the effects of the magnetic field configuration near the channel exit on the plume of Hall thrusters were conducted. The magnetic field configuration near the channel exit is characterized by the inclination angle between the magnetic field lines and the thruster radial direction. Different inclination angles were obtained by varying the current ratio in the coils. The plume divergence angles were measured by a dual-directed probe. The results showed that the plume divergence angle increased obviously with the increase in the magnitude of the inclination angle near the channel exit. Therefore, in order to optimize the magnetic field for reducing plume divergence, the magnitude of the inclination angle should be reduced as much as possible. It suggests that the magnetic field configuration near the channel exit is another important factor that affects plume divergence.
基金supported by National Natural Science Foundation of China(Nos.11375039 and 11275034)the Key Project of Science and Technology of Liaoning Province,China(No.2011224007)the Fundamental Research Funds for the Central Universities,China(No.3132014328)
文摘The influences of the low-emissive graphite segmented electrode t)laeed near the channel exit on the discharge characteristics of a Hall thruster are studied using the particle- in-cell method. A two-dimensional physical model is established according to the Hall thruster discharge channel configuration. The effects of electrode length on the potential, ion density, electron temperature, ionization rate and discharge current are investigated. It is found that, with tile increasing of the segmented electrode length, the equipotential lines bend towards the channel exit. and approximately parallel to the wall at the channel surface, the radial velocity and radial flow of ions are increased, and the electron temperature is also enhanced. Due to the conductive characteristic of electrodes, the radial electric field and the axial electron conductivity near the wall are enhanced, and the probability of the electron-atom ionization is reduced, which leads to the degradation of the ionization rate in the discharge channel. However, the interaction between electrons and the wall enhances the near wall conductivity, therefore the discharge current grows along with the segmented electrode length, and the performance of the thruster is also affected.
基金supported by the National Natural Science Foundation of China(Grant No.51477035)the Fundamental Research Funds for the Central Universities,China(Grant No.HIT.NSRIF 2015064)the Open Research Fund Program of State Key Laboratory of Cryogenic Vacuum Technology and Physics,China(Grant No.ZDK201304)
文摘In this paper, we summarize the research development of low-frequency oscillations in the last few decades. The findings of physical mechanism, characteristics and stabilizing methods of low-frequency oscillations are discussed. It shows that it is unreasonable and incomplete to model an ionization region separately to analyze the physical mechanism of low-frequency oscillations. Electro-dynamics as well as the formation conditions of ionization distribution play an important role in characteristics and stabilizing of low-frequency oscillations. Understanding the physical mechanism and characteristics of low- frequency oscillations thoroughly and developing a feasible method stabilizing this instability are still important research subjects.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.51507040,51777045 and 51736003)the Fundamental Research Funds for the Central Universities,China(Grant No.HIT.NSRIF.2015079)the Research Program,China(Grant No.JSZL2016203C006)
文摘A discharge channel with a chamfered wall not only has application in the design of modern Hall thrusters, but also exists where the channel wall is eroded, and so is a common status for these units. In this paper, the laws and mechanisms that govern the effect of the chamfered wall on the performance of a Hall thruster are investigated. By applying both experimental measurement and particle-in-cell simulation, it is determined that there is a moderate chamfer angle that can further improve the optimal performance obtained with a straight channel. This is because the chamfering of the wall near the channel exit can enhance ion acceleration and effectively reduce ion recombination on the wall, which is favorable to the promotion of the thrust and efficiency. However, the chamfer angle should not be too large; otherwise, both the density of the propellant gas and the distribution of the plasma potential in the channel are influenced, which is undesirable for efficient propellant utilization and beam concentration. Therefore, it is suggested that the chamfer shape of the channel wall is an important factor that must be carefully considered in the design of Hall thrusters.
基金supported by Changjiang Scholars and Innovative Research Team in University of China (PCSIRT)(No.IRT0520)National Natural Science Foundation of China (No.60671012)
文摘Considering the actual magnetic field configuration in a Hall thruster, the effect of magnetic mirror on the radial profile of near-wall conductivity (NWC) is studied in this paper. The plasma electron dynamic process is described by the test particle method. The Monte Carlo scheme is used to solve this model. The radial profile of electron mobility is obtained and the role of magnetic mirror in NWC is analysed both theoretically and numerically. The numerical results show that the electron mobility peak due to NWC is inversely proportional to the magnetic mirror ratio and the asymmetry of electron mobility along the radial direction gets greater when the magnetic mirror is considered. This effect indicates that apart from the disparity in the magnetic field strength, the difference in the magnetic mirror ratio near the inner and outer walls would actually augment the asymmetry of the radial profile of NWC in Hall thrusters.
基金support of National Natural Science Foundation of China(Grant Nos.51477035 and 51777045)
文摘In this paper, a direct connection between the discharge current amplitude and the thruster performance is established by varying solely the capacitance of the filter unit of the Hall thrusters. To be precise, the variation characteristics of ion current, propellant utilization efficiency, and divergence angle of plume at different low-frequency oscillation amplitudes are measured. The findings demonstrate that in the case of the propellant in the discharge channel just meets or falls below the full ionization condition, the increase of low-frequency oscillation amplitude can significantly enhance the ionization degree of the neutral gas in the channel and increase the thrust and anode efficiency of thruster. On the contrary, the increase in the amplitude of low-frequency oscillation will lead to increase the loss of plume divergence, therefore the thrust and anode efficiency of thruster decrease.
基金This work is funded by the Defense Industrial Technology Development Program(No.JCKY2019603B005)National Natural Science Foundation of China(Nos.52076054,51777045)the Hunan Science and Technology Innovation Project(No.2019RS1102).
文摘In this study,the neutral gas distribution and steady-state discharge under different discharge channel lengths were studied via numerical simulations.The results show that the channel with a length of 22 mm has the advantage of comprehensive discharge performance.At this time,the magnetic field intensity at the anode surface is 10%of the peak magnetic field intensity.Further analysis shows that the high-gas-density zone moves outward due to the shortening of the channel length,which optimizes the matching between the gas flow field and the magnetic field,and thus increases the ionization rate.The outward movement of the main ionization zone also reduces the ion loss on the wall surface.Thus,the propellant utilization efficiency can reach a maximum of 96.8%.Moreover,the plasma potential in the main ionization zone will decrease with the shortening of the channel.The excessively short-channel will greatly reduce the voltage utilization efficiency.The thrust is reduced to a minimum of 46.1 m N.Meanwhile,because the anode surface is excessively close to the main ionization zone,the discharge reliability is also difficult to guarantee.It was proved that the performance of Hall thrusters can be optimized by shortening the discharge channel appropriately,and the specific design scheme of short-channel of HEP-1350 PM was defined,which serves as a reference for the optimization design of Hall thruster with large height–radius ratio.The shortchannel design also helps to reduce the thruster axial dimension,further consolidating the advantages of lightweight and large thrust-to-weight ratio of the Hall thruster with large height–radius ratio.
基金supported by National Natural Science Foundation of China(Nos.10975026,10875024,11005025,11275034)the Scientific Research Program of the Education Bureau of Liaoning Province,China(No.2009A047)the State Key Development for Basic Research of China(Nos.2009GB105004,2009GB106002)
文摘In order to investigate the effects of secondary electrons, which are emitted from the wall, on the performance of a thruster, a one-dimensional fluid model of the plasma sheath in double walls is applied to study the characteristics of a magnetized sheath. The effects of secondary electron emission (SEE) coefficients and trapping coefficients, as well as magnetic field, on the structure of the plasma sheath are investigated. The results show that sheath potential and wall potential rise with the increment of SEE coefficient and trapping coefficient which results in a reduced sheath thickness. In addition, magnetic field strength will influence the sheath potential distributions.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.11505041 and 51776047)
文摘The cylindrical Hall thruster has the good prospect of serving as a miniaturized electric propulsion device.A 2 D-3 V particle-in-cell plus Monte Carlo(PIC-MCC) method is used to study the effect of the magnetic cusp on discharge characteristics of a cylindrical Hall thruster.The simulation results show that the main ionization region and the main potential drop of the thruster are located at the upstream of the discharge channel.When the magnetic cusp moves toward the anode side,the main ionization region is compressed and weakened,moving upstream correspondingly.The ionization near the cusp is enhanced,and the interaction between the plasma and the wall increases.The simulation results suggest that the magnetic cusp should be located near the channel exit.
基金National Natural Science Foundation of China(Nos.12005087 and 61901204)the Science and Technology Plan of Gansu Province(No.20JR10RA478)+1 种基金the Military Test Instruments Program(No.2006ZCTF0054)the Key Laboratory Funds for Science and Technology on Vacuum Technology and Physics Laboratory(No.HTKJ2019KL510003)。
文摘To achieve a better insight into the far-field plasma spatial distribution and evolution characteristics of the 300 W class low-power Hall thruster(LHT)for commercial aerospace applications,a dedicated and integrated plasma diagnostic system composed of seventeen Faraday cups(FC)and two triple Langmuir probes(TLP)is established to investigate the timeaveraged in situ spatial distribution characteristics of far-field ions and electrons.The ion current density(ICD),plasma potential,plasma density,and electron temperature at 1000 mm downstream of 300 W class LHT for commercial aerospace applications in the azimuthal angle range of-90°to 90°were investigated under the conditions of different anode mass flow rates and discharge voltages.The results demonstrated that ICD,beam divergence angle,and mass utilization efficiency increased with increasing anode mass rate.The double-wings phenomenon was observed in the spatial distribution of ICD at large angles from the thruster axis,which is attributed to charge exchange collisions at increasing vacuum backpressure.The plasma electron temperature,electron density,and plasma potential parameters derived from the TLP decreased rapidly in the angle range from 0°to 30°and did not exhibit significant variations above 30°,which was also in good agreement with the results of the measured divergence angle of the FC.The discrepancy of average ion speed was calculated.The maximum error is better than 31.5%which checks the consistency between the TLP’s results and that of FC to some extent.
基金financially supported by National Natural Science Foundation of China(Grant Nos.51777045 and51477035)Shenzhen Technology Project(Project Nos.JCYJ20160226201347750 and JCYJ20150529115038093)
文摘The intersection point of the characteristic magnetic field line(CMFL) crossing the anode boundary with the discharge channel wall, and its influence on thruster performance and the energy and flux of ions bombarding the channel wall, have been studied numerically. The simulation results demonstrate that with the increase in distance from the crossover point of the CMFL with the channel wall to the bottom of the thruster channel, the ionization rate in the discharge channel gradually increases; meanwhile, the ion energy and ion current density bombarding the channel wall decreases. When the point of the CMFL with the channel wall is at the channel outlet, the thrust, specific impulse, and efficiency are at a maximum, while the ion energy and ion current density bombarding the channel wall are at a minimum. Therefore, to improve the performance and lifetime of the thruster, it is important to control the point of intersection of the CMFL with the channel wall.