A review of ultra-high temperature heat-resistant energetic materials

Heat-resistant energetic materials refer to a type of energetic materials that possess a high melting point,high stability and operational safety. By studying the structures of these energetic materials has showed that the thermal stability can be enhanced by introducing amino groups to form intra/inter-molecular hydrogen bonds, constructing conjugate systems and designing symmetrical structures. This article aims to review the physical and chemical properties of ultra-high temperature heat-resistant energetic compounds and provide valuable theoretical insights for the preparation of ultra-high temperature heatresistant energetic materials. We also analyze the selected 20 heat-resistant energetic materials with decomposition temperatures higher than 350℃, serving as templates for the synthesis of various highperformance heat-resistant energetic materials.

Microstructures and mechanical properties of Mg-Al-Sm series heat-resistant magnesium alloys

The microstructures and phase compositions of the as-cast and die-cast Mg-6.02Al-1.03 Sm, Mg-6.05Al-0.98Sm-0.56 Bi and Mg-5.95Al-1.01Sm-0.57 Zn alloys were investigated. Meanwhile, the tensile mechanical and flow properties were tested. The results show that the as-cast microstructure of Mg-6.02Al-1.03 Sm alloy is composed of δ-Mg matrix, discontinuous δ-Mg17Al12 phase and small block Al2 Sm phase with high thermal stability. Rod Mg3Bi2 phase precipitates when Bi is added, while the added metal Zn dissolves into δ-Mg matrix and δ-Mg17Al12 phase. The as-cast alloys exhibit the excellent tensile mechanical property. The tensile strength（δb） and elongation（δ） can reach 205-235 MPa and 8.5%-16.0% at ambient temperature, respectively. Meanwhile, they can also exceed 160 MPa and 14.0% at 423 K, respectively. The die-cast microstructures are refined obviously, and meanwhile the broken second phases distribute dispersedly. The die-cast alloys exhibit better tensile mechanical properties with the values of δb and δ of 240-285 MPa and 8.5%-16.5% at ambient temperature, respectively, and excellent flow property with the flow length of 1870-2420 mm. The die-cast tensile fractures at ambient temperature exhibit a typical character of ductile fracture.

Studies on the Triterpenoid Constituents of the Spores from Ganoderma lucidum Karst

Five compounds were isolated from the ether-soluble fraction of the spores of Gano- derma lucidum.On the basis of their chemical properties and spectral data(MS,UV,IR,~1H and ^(13)CNMR),they were identified as 3,7,11,12,15,23-hexaoxo-5α-lanosta-8-en-26-oic acid(Ⅰ),gano- deric acid B(Ⅱ),C(Ⅲ),D(Ⅳ)and ganodermanontriol(Ⅴ).Compound Ⅰ is a new natural product, named ganosporeric acid A.Compounds Ⅱ,Ⅲ,Ⅳ and Ⅴ are known compounds and were obtained for the first time from the spores of Ganoderma lucidum.Pharmacological experiments showed that ganosporeric acid A has an activity for lowering the levels GPT in mice with liver injury by CCl_4 and GaNI and exhibits heptoprotective effects.

Isolation and Structural Determination of a Glucan from the Spores of Ganoderma lucidum

A water soluble, (1 -->6)-branched, (1 -->4) linked D-glucan (LB-B1), [alpha](D)(21) = +174.2 degrees (c 0.87, H2O), was obtained from a hot-water extract of the sporoderm-broken spores of Ganoderma lucidun (Fr.) Karst by HPSEC, with 0.001 mol/L sodium hydroxide as the eluant, the molecular weight (Mw) of LB-B1 was estimated to be 9.3 x 10(3). From the results of total hydrolysis, methylation analysis, acetolysis and 1D, 2D-NMR experimentation, it was concluded that LB-B1 was composed of repeating units with the following structure: alpha -D-Glc(p)-(1 -->6)-alpha -D-Glc(p)-(1 -->6)-alpha -D-Glc(p) 1 down arrow 6 (-->4)-alpha -D-Glc(p)-(1 -->4)-alpha -D-Glc(p)-(1 -->4)-alpha -D-Glc(p)-(1 -->4)-alpha -D-Glc(p)-(1 -->4-)-alpha -D-Glc(p)-(1 -->)(n)

Control Efficacy of Validamycin A·(0.2 Billion Spores/ml) Paenibacillus polymyxa DN-1 3% AS for Rice Sheath Blight

With validamycin A.（0.2 billion spores/ml） Paenibacillus polymyxa DN-1 3% AS as the test agent, the effects of different dosage and different application time on the control efficacy for＇ rich sheath blight were investigated. The results of two- year test showed that when the application amount was in the range of 45-90 g.a.i/ hm^2, the field efficacy of validamycin A-（0.2 billion spores/ml） P. polymyxa DN-1 3% AS in the initial infection stage of rich sheath blight （Le., the diseased plant rate was below 5%） reached 80.38%-89.06%, and that in the peak infection stage （i.e., the diseased plant rate was higher than 10%） reached only 41.12%-53.26%. The field efficacy of validamycin A.（0.2 billion spores/ml） P. polymyxa DN-1 3% AS at the early onset of rich sheath blight was significantly better than that at the onset, so that the application time of validamycin A .（0.2 billion spores/ml） P. polymyxa DN-1 3% AS should be appropriately brought forward in the prevention and control of rice sheath blight.

Cuticles and Spores in Situ of Coniopteris hymenophylloides from the Middle Jurassic in Gansu, Northwestern China

Coniopteris was a ubiquitous plant of the Jurassic and Cretaceous periods and played an important role in the flora of the time. However, its anatomical structure is relatively poorly known. The specimens of Coniopteris hymenophylloides(Brongniart) Seward described here were collected from the Yaojie Formation in Gansu Province, northwestern China. The sterile fronds are characterized as being at least bipinnate with alternate arranged linear pinnae covered by thin cuticles. Fertile fronds are linear-lanceolate, with single sorus at the margin of each fertile pinnule. In situ spores are typically trilete, triangle to subcircular in polar view, cap-shaped in equatorial view, and 37 μm in average diameter. The trilete marking is straight and narrow, generally extends to 4/5 of the spore radius. The spore surface is smooth, and parts of the exine are granulated. The epidermal cells of cuticles are irregular in shape, approximately 40-60μm long and 10-20 μm wide. The elliptical stomatal complexes are paracytic,approximately 30 μm long and 19 μm wide,and irregularly distributed. On the basis of its epidermal structures and comparisons with extant ferns, we consider that Coniopteris displays combined features of the related extant genera.

Influence of Ganoderma lucidum spores on the levels of neuropeptide Y and somatostatin in brains of seizure rats

BACKGROUND： Previous research has revealed that somatostatin can induce epilepsy, and that the levels of neuropeptide Y may increase and become more active in brain areas with epileptic seizures. OBJECTIVE： To observe the effect of Ganoderma luciclum spore powder on the neuropeptide Y and somatostatin content in the cerebral cortex and hippocampal regions of seizure rats induced by pentylenetetrazol （PTZ）. Furthermore, to verify any effect of Ganoderma lucidum spore powder on inhibition of epileptic seizures. DESIGN, TIME AND SETTING： A randomized group animal study was performed in August 2007 in the School of Basic Medical Sciences, Jiamusi University （Jiamusi, Heilongjiang, China）. MATERIALS： Thirty healthy, male, Wistar rats, aged 12 weeks and weighing 180-220 g, were taken as the experimental animals. PTZ （Sigma Company, United States） was used to induce epilepsy. Ganoderma lucidum spores （Leyss, ex Fr variety） were purchased from Jiamusi City Wild Growing Case of the Ganoderma Lucidum （China）. Rabbit anti-somatostatin antibodies and secondary antibodies were purchased from Wuhan Boster Company （China）. Neuropeptide Y radioimmunoassay kit was purchased from Beijing Furui Biotechnology Company （China）. METHODS： Thirty rats were randomly divided into three groups： a control group, an epilepsy model group and a Ganoderma lucidum spore-treated group. Each group contained 10 animals. Rats in the epilepsy model group were treated with intraperitoneal injections of PTZ and gastric perfusion of physiologic saline. In the Ganoderma lucidum spore-treated group, intraperitoneal injection of PTZ and gastric perfusion of Ganoderma lucidum spore powder were administered. The blank control group was only administered with the physiological saline by intraperitoneal injection and gastric perfusion. MAIN OUTCOME MEASURES： Immunohistochemical staining and radioimmunoassay methods were used to observe the changes of somatostatin and neuropeptide Y content in brain tissue of epileptic rats, as well as the morphology of neurons. RESULTS： All 30 rats were involved in the result analysis, without any loss. The number of somatostatin immunoreacted positive cells in the cerebral cortex and hippocampus was significantly increased in the epilepsy model group compared to the blank control group （P 〈 0.01）. The number of somatostatin immunoreacted positive cells in cerebral cortex and hippocampus was significantly decreased in the Ganoderma lucidum spore-treated group compared to the epilepsy model group （P 〈 0.01）. The contents of neuropeptide Y in cerebral cortex and hippocampus were significantly increased in the epilepsy model group compared to the blank control group （P 〈 0.01）. The contents of neuropeptide Y in the cerebral cortex and hippocampus were significantly decreased in the Ganoderma lucidum spore-treated group compared to the epilepsy model group （P 〈 0.05）. The epilepsy seizures in the Ganoderma lucidum spore-treated group were obviously reduced compared to the epilepsy model group. CONCLUSION： Ganoderma lucidum spore powder was able to reduce the somatostatin and neuropeptide Y content in the cerebral cortex and hippocampus effectively, so as to achieve an anti-epileptic function and protect neurons from being damaged.

Construction of Electrocatalytic and Heat-Resistant Self-Supporting Electrodes for High-Performance Lithium–Sulfur Batteries

Boosting the utilization efficiency of sulfur electrodes and suppressing the“shuttle effect”of intermediate polysulfides remain the critical challenge for high-performance lithium-sulfur batteries(LSBs).However,most of reported sulfur electrodes are not competent to realize the fast conversion of polysulfides into insoluble lithium sulfides when applied with high sulfur loading,as well as to mitigate the more serious shuttle effect of polysulfides,especially when worked at an elevated temperature.Herein,we reported a unique structural engineering strategy of crafting a unique hierarchical multifunctional electrode architecture constructed by rooting MOF-derived CoS2/carbon nanoleaf arrays(CoS2-CNA)into a nitrogen-rich 3D conductive scaffold(CTNF@CoS2-CNA)for LSBs.An accelerated electrocatalytic effect and improved polysulfide redox kinetics arising from CoS2-CNA were investigated.Besides,the strong capillarity effect and chemisorption of CTNF@CoS2-CNA to polysulfides enable high loading and efficient utilization of sulfur,thus leading to high-performance LIBs performed not only at room temperature but also up to an elevated temperature(55°C).Even with the ultrahigh sulfur loading of 7.19 mg cm?2,the CTNF@CoS2-CNA/S cathode still exhibits high rate capacity at 55°C.

Effect of RE addition on solidification process and high-temperature strength of Al-12%Si-4%Cu-1.6%Mn heat-resistant alloy

The effect of RE addition on solidification process and high-temperature strength of Al-12%Si-4%Cu-1.6%Mn(in wt.%)heat-resistant alloy was investigated by microstructure observation and tensile test.A great number of fine needle-like RE-rich phases are observed in the alloys with RE addition. Solutionizing treatment does not change their morphologies and sizes, indicating that they have good thermal stability. The addition of RE totally alters the solidification process of eutectic CruAl2 phase, from network-like phase in the form of segregation at the final eutectic grain boundaries to discretely blocky phase growing on the hair-filamentous RE-rich needles. In the alloys with Ce addition, blocky CuAl2, particulate Al15Mn3Si2 and needle-like RE-rich needle phases grow together, but they did not occur in the alloy with only La addition. The addition of RE does not considerably improve the strength of the alloy at high temperatures. The formation of RE-rich phases also does not significantly alter the originating and propagating of micro-cracks in the alloy during tensile test.

Breaking and Characteristics of Ganoderma Lucidum Spores by High Speed Entrifugai Shearing Pulverizer

The spores of Ganoderma lucidum were ground and broken to ultrafine particles by high speed centrifugal shearing（HSCS） pulverizer. The characteristics of Ganoderma lucidum spores were analyzed by scanning electron microscope （SEM）, Fourier transform infrared spectrophotometry （FTIR）. Ultraviolet-visible pectrophotometer was used to determine the extraction ratio of aqueous solubility polysaccharide between the raw and broken spores. The immunological function on the mice before and after the breaking of spores wan investigated. The experimental results show that after being ground, the sporoderm-broken ratio reachs 100%, the original active ingredients of ganoderma lucidum spores do not change, and the extraction ratio of aqueous solubility polysaccharide is greatly increased by 40.08%. The broken spores show much higher immunological activity comparing with original spores of Ganoderma lucidum.

Influence of Long Chain Free Fatty Acids on the Thermal Resistance Reduction of Bacterial Spores

Aims: The objective of this study was to investigate the effect of free fatty acid length chain and unsaturated bond number on the heat resistance and recovery media of bacterial spores. Methods and results: For 6 species, bacterial spore heat resistances were estimated at different free fatty acid concentrations added to heating media or in recovery media. The addition of free fatty acids to heating media has a slight influence on the heat resistance of bacterial spores whatever the species or type of acid studied. On the contrary, the addition of free fatty acids to the recovery medium after the heat treatment greatly reduces the ability to bacterial spores to recover and form colonies. This effect varies depending on chain length, unsaturated bond number of fatty acid and on the bacterial strain studied. Conclusion: The presence of free acids in the recovery media is an additive stress which decreases the capability of injured spores to germinate and grow thereafter. Significance and impact of this study: The impact of free fatty acids presented in this study can be taken into account to reduce the thermal intensity of food sterilization in relation to their availability in food matrix.

The study of airborne pollen and spores inTaoyuan, Hunan Province of China

In order to study the airborne pollen and Spores, a circular year airborne Samples werecollected at 10m height above ground from Taoyuan ecological station, which is located in TaoyuanCounty of Hunan Province. The analytical results showed that there are 188 plant families and generain airborne pollen and spores. of them, 102 are xylophyte plants, 68 are herbase plat, and 18are pteridophyta plants. The plant families and genera account for 80% of the local plant families andgenera. Among them, 54 are specific families and genera, Which are peculiar tO tropics andsubtropics. The main pollen and spore families and genera are Pinus. Cunninghamia Juglans,Quercus, Cupressaceae, Urticaceac, and Gleicheniaceae. There are two peak stages of airbornepollen and spore concentration throughout the year. One is the peak stage of xylophyte plants fromMarch to May and the other, herbaceous plants from niddle dekad of August to early October. Themaximum year round value is 850 000 grains/1000m3.air in middle dekad of September and theminimum is 1500 grains/1000m3.air in early December. In the local district, the airbome pollen andSpores which can induce respiratory tract disease in spring are Taxodiaceae, Cupresaseeae, CastrieaCastanopsis, Queme, Juglans, Platycarya, and that can induce disease in autumn are Canabis,Gramineae, and Artmisia.

New Discovery of Reproductive Organs and Spores in Situ of Ginkgoales and Czekanowskiales from the Middle Jurassic of Shaanxi, China

Objective Ginkgoales and Czekanowskiales are important components of Mesozoic flora and were widely distributed in the Northern Hemisphere. They are usually preserved together in the stratum. Their fossils are abundant in the Middle Jurassic of Shaanxi Province, but there are no reports on their reproductive organs. Here, we report two male gymnospermous pollen cones from the Middle Jttrassic Yan＇an Formation of the northeast Yulin City, Shaanxi Province, China. The characteristics of the fossils, including those of pollens, have been described in detail. The new specimens were compared with fossils closely similar in morphology, and the taxonomic affinity and systematies were established. The present results offer new fossil materials for the study of taxonomy, evolution, and phytogeography of Ginkgoales and Czekanowskiales.

Achieving a high-strength dissimilar joint of T91 heat-resistant steel to 316L stainless steel via friction stir welding

The reliable welding of T91 heat-resistant steel to 316L stainless steel is a considerable issue for ensuring the safety in service of ultrasupercritical power generation unit and nuclear fusion reactor,but the high-quality dissimilar joint of these two steels was difficult to be obtained by traditional fusion welding methods.Here we improved the structure-property synergy in a dissimilar joint of T91 steel to 316L steel via friction stir welding.A defect-free joint with a large bonding interface was produced using a small-sized tool under a relatively high welding speed.The bonding interface was involved in a mixing zone with both mechanical mixing and metallurgical bonding.No obvious material softening was detected in the joint except a negligible hardness decline of only HV~10 in the heat-affected zone of the T91 steel side due to the formation of ferrite phase.The welded joint exhibited an excellent ultimate tensile strength as high as that of the 316L parent metal and a greatly enhanced yield strength on account of the dependable bonding and material renovation in the weld zone.This work recommends a promising technique for producing high-strength weldments of dissimilar nuclear steels.

Influence of Creep Strength of Weld on Interfacial Creep Damage of Dissimilar Welded Joint between Martensitic and Bainitic Heat-Resistant Steel

The mechanical properties, creep rupture strength, creep damage and failure characteristics of dissimilar metal welded joint （DMWJ） between martensitic （SA213T91） and bainitic heat-resistant steel （12Cr2MoWVTiB（G102）） have been investigated by means of pulsed argon arc welding, high temperature accelerated simulation, mechanical and creep rupture test, and scanning electronic microscope （SEM）. The results show that there is a marked drop of mechanical properties of undermatching joint, and low ductility cracking along weld/G102 interface is induced due to creep damage. Creep rupture strength of overmatching joint is the least. The mechanical properties of medium matching joint are superior to those of overmatching and undermatching joint, and creep damage and failure tendency along the interface of weld/G102 are lower than those of overmatching and undermatching joint after accelerated simulation for 500 h, 1 000 h, 1 500 h, and the creep rupture strength of medium matching joint is the same as that of undermatching joint. Therefore, it is reasonable that the medium matching material is used for dissimilar welded joint between martensitic and bainitic steel.

Dissolution Behavior of Delta Ferrites in Martensitic Heat-resistant Steel for Ultra Supercritical Units Blades

The dissolution behavior of delta ferrites in martensitic heat-resistant steel was studied.And the reason why the dissolution rate of delta ferrites decreased with dissolution time was discussed.The experimental results show that the chemical compositions of delta ferrites negligibly change with dissolution time.The decrease of dissolution rate of delta ferrites with dissolution time should be attributed to the change of shape and distribution of delta ferrites.The shape of delta ferrites tends to transfer from polygon to sphere with dissolution time,causing the decrease of specific surface area of delta ferrites.The distribution position of delta ferrites tends to transfer from boundaries of austenite grains to interior of austenite grains with dissolution time,decreasing the diffusion coefficient of alloy atoms.Both them decrease the dissolution rate of delta ferrites.

High-temperature oxidation behavior of 9Cr‒5Si‒3Al ferritic heat-resistant steel

To improve the oxidation properties of ferritic heat-resistant steels,an Al-bearing 9Cr‒5Si‒3Al ferritic heat-resistant steel was designed.We then conducted cyclic oxidation tests to investigate the high-temperature oxidation behavior of 9Cr‒5Si and 9Cr‒5Si‒3Al ferritic heat-resistant steels at 900 and 1000℃.The characteristics of the oxide layer were analyzed by X-ray diffraction,scanning electron microscopy,and energy dispersive spectroscopy.The results show that the oxidation kinetics curves of the two tested steels follow the parabolic law,with the parabolic rate constant kp of 9Cr‒5Si‒3Al steel being much lower than that of 9Cr‒5Si steel at both 900 and 1000℃.The oxide film on the surface of the 9Cr‒5Si alloy exhibits Cr2MnO4 and Cr2O3 phases in the outer layer after oxidation at 900 and 1000℃.However,at oxidation temperatures of 900 and 1000℃,the oxide film of the 9Cr‒5Si‒3Al alloy consists only of Al2O3 and its oxide layer is thinner than that of the 9Cr‒5Si alloy.These results indicate that the addition of Al to the 9Cr‒5Si steel can improve its high-temperature oxidation resistance,which can be attributed to the formation of a continuous and compact Al2O3 film on the surface of the steel.

Microstructure and mechanical properties of a cast heat-resistant rare-earth magnesium alloy

Microstructure,mechanical properties and phase transformation of a heat-resistant rare-earth(RE)Mg-16.1Gd-3.5Nd-0.38Zn-0.26Zr-0.15Y(wt.%)alloy were investigated.The as-cast alloy is composed of equiaxedα-Mg matrix,net-shaped Mg5RE and Zr-rich phases.According to aging hardening curves and tensile properties variation,the optimized condition of solution treatment at 520℃for 8 h and subsequent aging at 204℃for 12 h was selected.The continuous secondary Mg5RE phase predominantly formed at grain boundaries during solidification transforms to residual discontinuousβ-Mg5RE phase and fine cuboid REH2particles after heat treatment.The annealed alloy exhibits good comprehensive tensile property at 350℃,with ultimate tensile strength of 153 MPa and elongation to fracture of 6.9%.Segregation of RE elements and eventually RE-rich precipitation at grain boundaries are responsible for the high strength at elevated temperature.

Energy status regulated umami compound metabolism in harvested shiitake mushrooms(Lentinus edodes)with spores triggered to release

The molecular mechanisms of energy status related to the umami taste of postharvest shiitake mushrooms during spore release remain poorly understood.In this study,the variations of energy status and umami taste of mushrooms were measured at 25℃.At 24 h storage,slight spore prints of mushrooms were first pictured,respiration peaked.Significant ATP decrease and ADP increase were also observed as the initiation of postharvest senescence(P<0.05).Meanwhile,the activities of phosphohexose isomerase,succinate dehydrogenase,glucose-6-phosphate dehydrogenase and cytochrome c oxidase and the contents of umami nucleotides and amino acids were maintained at higher levels in mushrooms with spore release.Notably,the equivalent umami concentration(EUC)was strongly correlated with energy levels(R=0.80).Fifteen related gene expression levels in the energy metabolism pathway were downregulated.LecpdP1 and LeAK were significantly expressed in the conversion of ATP into AMP and played key roles in connecting the energy state and umami level.These results provided valuable insights on the umami taste associated with energy metabolism mechanism during postharvest mushroom spore release.

Microstructure and Corrosion Resistance of CrN and CrN/TiN Coated Heat-Resistant Steels in Molten Aluminum Alloy

The components of the equipment for processing the Al melts into the molded parts can be markedly corroded by the molten Al. In this study, a 4 μm CrN coating or CrN/TiN multilayer coating for providing the physical and chemical barriers between the molten reactive Al and the steel substrate were deposited by Cathodic Arc Evaporation onto 10 mm-thick heat-resistant steel plates. The dipping tests were conducted in a 700℃ A356 melt for 1 to 21 h at intervals of 3 h. The damage of the coated steel was eva...