Ultrafast dynamics of femtosecond laser-induced high spatial frequency periodic structures on silicon surfaces

Femtosecond laser-induced periodic surface structures(LIPSS)have been extensively studied over the past few decades.In particular,the period and groove width of high-spatial-frequency LIPSS(HSFL)is much smaller than the diffraction limit,making it a useful method for efficient nanomanufacturing.However,compared with the low-spatial-frequency LIPSS(LSFL),the structure size of the HSFL is smaller,and it is more easily submerged.Therefore,the formation mechanism of HSFL is complex and has always been a research hotspot in this field.In this study,regular LSFL with a period of 760 nm was fabricated in advance on a silicon surface with two-beam interference using an 800 nm,50 fs femtosecond laser.The ultrafast dynamics of HSFL formation on the silicon surface of prefabricated LSFL under single femtosecond laser pulse irradiation were observed and analyzed for the first time using collinear pump-probe imaging method.In general,the evolution of the surface structure undergoes five sequential stages:the LSFL begins to split,becomes uniform HSFL,degenerates into an irregular LSFL,undergoes secondary splitting into a weakly uniform HSFL,and evolves into an irregular LSFL or is submerged.The results indicate that the local enhancement of the submerged nanocavity,or the nanoplasma,in the prefabricated LSFL ridge led to the splitting of the LSFL,and the thermodynamic effect drove the homogenization of the splitting LSFL,which evolved into HSFL.

Tunable wideband absorber based on resistively loaded lossy high-impedance surface

A lossy high-impedance surface comprised of two layers of resistive frequency selective surfaces is employed to design a tunable electromagnetic absorber. The tunability is realized through changing the composite unit cell by moving the top layer mechanically. To explain the absorbing mechanism, an equivalent circuit model with an interacting coefficient is proposed. Then, simulations and measurements are carried out and agree well with each other. Results show that the complex structure with a thickness less than λ0/4 is able to achieve a wideband absorption in a frequency range from5.90 GHz to 19.73 GHz. Moreover, it is tunable in the operation frequency band.

High surface area biocarbon monoliths for methane storage

New energy sources that reduce the volume of harmful gases such as SO_(x)and NO_(x)released into the atmosphere are in constant development.Natural gas,primarily made up of methane,is being widely used as one reliable energy source for heating and electricity generation due to its high combustion value.Currently,natural gas accounts for a large portion of electricity generation and chemical feedstock in manufacturing plastics and other commercially important organic chemicals.In the near future,natural gas will be widely used as a fuel for vehicles.Therefore,a practical storage device for its storage and transportation is very beneficial to the deployment of natural gas as an energy source for new technologies.In this tutorial review,biomaterials-based carbon monoliths(CMs),one kind of carbonaceous material,was reviewed as an adsorbent for natural gas(methane)adsorption and storage.

High impedance fault detection in distribution network based on S-transform and average singular entropy

When a high impedance fault(HIF)occurs in a distribution network,the detection efficiency of traditional protection devices is strongly limited by the weak fault information.In this study,a method based on S-transform(ST)and average singular entropy(ASE)is proposed to identify HIFs.First,a wavelet packet transform(WPT)was applied to extract the feature frequency band.Thereafter,the ST was investigated in each half cycle.Afterwards,the obtained time-frequency matrix was denoised by singular value decomposition(SVD),followed by the calculation of the ASE index.Finally,an appropriate threshold was selected to detect the HIFs.The advantages of this method are the ability of fine band division,adaptive time-frequency transformation,and quantitative expression of signal complexity.The performance of the proposed method was verified by simulated and field data,and further analysis revealed that it could still achieve good results under different conditions.

Dynamic surface control-backstepping based impedance control for 5-DOF flexible joint robots

A new impedance controller based on the dynamic surface control-backstepping technique to actualize the anticipant dynamic relationship between the motion of end-effector and the external torques was presented.Comparing with the traditional backstepping method that has "explosion of terms" problem,the new proposed control system is a combination of the dynamic surface control technique and the backstepping.The dynamic surface control(DSC) technique can resolve the "explosion of terms" problem that is caused by differential coefficient calculation in the model,and the problem can bring a complexity that will cause the backstepping method hardly to be applied to the practical application,especially to the multi-joint robot.Finally,the validity of the method was proved in the laboratory environment that was set up on the 5-DOF(degree of freedom) flexible joint robot.Tracking errors of DSC-backstepping impedance control that were 2.0 and 1.5 mm are better than those of backstepping impedance control which were 3.5 and 2.5 mm in directions X,Y in free space,respectively.And the anticipant Cartesian impedance behavior and compliant behavior were achieved successfully as depicted theoretically.

Efficient Computation of Scattering from Targets with Negative Impedance Surface

Current surface integral equations used for computing scattering from targets with negative impedance boundary condition(IBC)are not efficient.A modified surface dual integral equation(M-SDIE)for targets with negative IBC is presented.A pure imaginary number is used to balance the formulations.It is proved that the M-SDIE is accurate and efficient with three numerical examples.The first numerical example shows that the M-SDIE is accurate compared with Mie.The second example shows that the presented SIE is efficient.In the third example,a missile head is selected to present the computing power of the M-SDIE.All the examples show that the M-SDIE is an efficient algorithm for negative IBC.

ANALYSIS OF DYNAMIC INSTABILITY OF INTERFACIAL SLIP WAVES BASED ON THE SURFACE IMPEDANCE TENSOR

A new method relying on the Stroh formulism and the theory of the surface impedance tensor was developed to investigate the dynamic instability of interfacial slip waves.The concept of the surface impedance tensor was extended to the case where the wave speed is of a complex value,and the boundary conditions at the frictionally contacting interface were expressed by the surface impedance tensor.Then the boundary value problem was transformed to searching for zeroes of a complex polynomial in the unit circle.As an example,the steady frictional sliding of an elastic half-space in contact with a rigid flat surface was considered in details.A quartic complex characteristic equation was derived and its solution behavior in the unit circle was discussed.An explicit expression for the instability condition of the interfacial slip waves was presented.

Surface Dissociation Properties of Short Chain Carboxyl Mercaptan Self-Assembled Monolayers by Impedance Titration

Impedance titration was used to determine the surface dissociation characteristics of short-chain carboxyl mercaptan self-assembled monolayers (SAMs). Based on the change of the cyclic voltammetric peak current and the charge-transfer resistance,which was related to pH value of the solution,the surface pKα of mercaptoacetic acid(MA),3-mercaptopropionic acid(MPA) and ω-mercaptohexanic acid(MHA) self-assembled membranes,with ionic strength being 0.1 mol/L,were determined to be 5.20,4.80,7.40,respectively. In addition,factors such as time needed for assembling,structure of monolayers and ionic strength,which effected the surface pKα,were studied as well. Such surface pKα shifts were sufficiently explained by interactions between interfacial molecules and hydrophobicity.

Optimization of High-Protein Glutinous Rice Flour Production Using Response Surface Method

A response surface method was employed to study the effect of α-amylase concentration, hydrolysis temperature and time on the production of high protein glutinous rice flour(HPGRF). The suspension of glutinous rice flour(15%) that contained 6.52% protein was gelatinized and subsequently hydrolyzed by thermostable α-amylase. The hydrolysis yielded 0.144–0.222 g/g HPGRF with 29.4%–45.4% protein content. Hydrolysis time exerted a significant effect, while enzyme concentration and hydrolysis temperature showed insignificant effect on the protein content and production yield of HPGRF. The result of response surface method showed that the optimum condition for the production of HPGRF that contained at least 36% protein was treating gelatinized 15% glutinous rice flour suspension with 0.90 Kilo Novo α-amylase Unit(KNU)/g α-amylase at 80 oC for 99 min. By carrying out the predicted hydrolysis condition, HPGRF with 35.9% protein and 61.8% carbohydrates was resulted. The process yielded 0.172 g/g HPGRF. HPGRF contained higher amount of essential amino acids compared to glutinous rice flour. HPGRF had higher solubility and lower swelling power, and also showed no pasting peak compared with glutinous rice flour.

Hierarchical microstructures with high spatial frequency laser induced periodic surface structures possessing different orientations created by femtosecond laser ablation of silicon in liquids

High spatial frequency laser induced periodic surface structures(HSFLs)on silicon substrates are often developed on flat surfaces at low fluences near ablation threshold of 0.1 J/cm2,seldom on microstructures or microgrooves at relatively higher fluences above 1 J/cm^2.This work aims to enrich the variety of HSFLs-containing hierarchical microstructures,by femtosecond laser(pulse duration:457 fs,wavelength:1045 nm,and repetition rate:100 kHz)in liquids(water and acetone)at laser fluence of 1.7 J/cm^2.The period of Si-HSFLs in the range of 110–200 nm is independent of the scanning speeds(0.1,0.5,1 and 2 mm/s),line intervals(5,15 and 20μm)of scanning lines and scanning directions(perpendicular or parallel to light polarization direction).It is interestingly found that besides normal HSFLs whose orientations are perpendicular to the direction of light polarization,both clockwise or anticlockwise randomly tilted HSFLs with a maximal deviation angle of 50°as compared to those of normal HSFLSs are found on the microstructures with height gradients.Raman spectra and SEM characterization jointly clarify that surface melting and nanocapillary waves play important roles in the formation of Si-HSFLs.The fact that no HSFLs are produced by laser ablation in air indicates that moderate melting facilitated with ultrafast liquid cooling is beneficial for the formation of HSFLs by LALs.On the basis of our findings and previous reports,a synergistic formation mechanism for HSFLs at high fluence was proposed and discussed,including thermal melting with the concomitance of ultrafast cooling in liquids,transformation of the molten layers into ripples and nanotips by surface plasmon polaritons(SPP)and second-harmonic generation(SHG),and modulation of Si-HSFLs direction by both nanocapillary waves and the localized electric field coming from the excited large Si particles.

Preparation of Zirconia-Ceria Powders with High Specific Surface Area

Zirconia-ceria mixed oxide powders were prepared by high temperature aging method.The effects of the temperature and the time of aging, cerium content and calcination on powder performance were studied.The result shows that high temperature aging is an efficient way of preparation of ZrO2-CeO2 mixed oxide powders with high specific surface area and good thermal stability, and that addition of a small amount of cerium to hydrous zirconia can promote the preparation of high specific surface area powders.

Effect of Quenching Parameters on Mechanical Property of Ultra High Strength Steel BR1500HS Based on Response Surface Methodology

Hot stamping of high strength steels is defined as a process in which blank is heated to the temperature of the austenite stabilization region for a definite time and then formed and quenched simultaneously in a mold with cooling channels. During this process,the processing parameters of austenite temperature and soaking time have strong effects on the mechanical properties such as quenching hardness,tensile strength and elongation. Hence,it is necessary to investigate the relationship between the mechanical properties and the two processing parameters. In this paper,the orthogonal experiment with two factors and five levels was applied, and the experimental data based on the orthogonal experiment was acquired. Based on the data,regression models were set up and the results of the analysis of variance( ANOVA) showed that it is reliable to predict the quenching hardness,tensile strength and elongation by the regression models. Besides,the optimal results of each single object were obtained based on response surface methodology( RSM),and global optimums was gained by employing ideal point method in which the quenching hardness,and tensile strength and elongation were considered simultaneously.

Experimental Investigation on the Bush Inner Surface Temperature of a High Speed Spiral Oil Wedge Sleeve Bearing

The temperature of bush inner surface temperature is measured by using infrared thermometer and transparent bearing,and temperature rise is measured by using thermocouple. The influence of rotating speed and axial location on the bush inner surface temperature is studied,and the influence of supply pressure and rotating speed on the temperature rise is analyzed. The results show the bush inner surface temperature and temperature rise of spiral oil wedge hydrodynamic bearing increase with the increase of rotation speed. In axial direction,the temperature is higher around the oil return hole. The temperature rise decreases with the increase of supply pressure. The highest temperature of bush inner surface and temperature rise are higher at higher speed,so the temperature rise is the fundamental reason which restricts the increase of rotation speed for high speed sleeve bearing.

Surface segregation of InGaAs films by the evolution of reflection high-energy electron diffraction patterns

Surface segregation is studied via the evolution of reflection high-energy electron diffraction (RHEED) patterns under different values of As 4 BEP for InGaAs films. When the As 4 BEP is set to be zero, the RHEED pattern keeps a 4×3/(n×3) structure with increasing temperature, and surface segregation takes place until 470 C. The RHEED pattern develops into a metal-rich (4×2) structure as temperature increases to 495 C. The reason for this is that surface segregation makes the In inside the InGaAs film climb to its surface. With the temperature increasing up to 515 C, the RHEED pattern turns into a GaAs(2×4) structure due to In desorption. While the As 4 BEP comes up to a specific value (1.33×10 4 Pa–1.33×10 3 Pa), the surface temperature can delay the segregation and desorption. We find that As 4 BEP has a big influence on surface desorption, while surface segregation is more strongly dependent on temperature than surface desorption.

Adiabatic cooling for cold polar molecules on a chip using a controllable high-efficiency electrostatic surface trap

We propose a controllable high-efficiency electrostatic surface trap for cold polar molecules on a chip by using two insulator-embedded charged rings and a grounded conductor plate. We calculate Stark energy structure pattern of ND3 molecules in an external electric field using the method of matrix diagonalization. We analyze how the voltages that are applied to the ring electrodes affect the depth of the efficient well and the controllability of the distance between the trap center and the surface of the chip. To obtain a better understanding, we simulate the dynamical loading and trapping processes of ND3 molecules in a |J, KM = |1,-1 state by using classical Monte–Carlo method. Our study shows that the loading efficiency of our trap can reach ～ 88%. Finally, we study the adiabatic cooling of cold molecules in our surface trap by linearly lowering the potential-well depth(i.e., lowering the trapping voltage), and find that the temperature of the trapped ND3 molecules can be adiabatically cooled from 34.5 m K to ～ 5.8 m K when the trapping voltage is reduced from-35 k V to-3 k V.

New technologies in the gastrointestinal clinic and research: Impedance and high-resolution manometry

The last five years have been an exciting time in the study of esophageal motor disorders due to the recent advances in esophageal function testing. New technologies have emerged, such as intraluminal impedance, while conventional techniques, such as manometry, have enjoyed many improvements due to advances in transducer technology, computerization and graphic data presentation. While these techniques provide more detailed information regarding esophageal function, our understanding of whether they can improve our ability to diagnose and treat patients more effectively is evolving. These techniques are also excellent research tools and they have added substantially to our understanding of esophageal motor function in dysphagia. This review describes the potential benefits that these new technologies may have over conventional techniques for the evaluation of dysphagia.

Relationship of Initiator Length with Fractal Dimension of Fractured Surfaces of High Strength Steels

Length-yardstick relation was used for measurement of the fractal dimension and the length of the initiator of Koch curves. It was found that the higher the fractal dimension and then the fracture toughness, the shorter the length of the initiator of the Koch curve for the crack lines would be.

Surface Topography and Roughness of High-speed Milled AlMn1Cu

The aluminum alloy Al Mn1 Cu has been broadly applied for functional parts production because of its good properties. But few researches about the machining mechanism and the surface roughness were reported. The high-speed milling experiments are carried out in order to improve the machining quality and reveal the machining mechanism. The typical topography features of machined surface are observed by scan electron microscope(SEM). The results show that the milled surface topography is mainly characterized by the plastic shearing deformation surface and material piling zone. The material flows plastically along the end cutting edge of the flat-end milling tool and meanwhile is extruded by the end cutting edge, resulting in that materials partly adhere to the machined surface and form the material piling zone. As the depth of cut and the feed per tooth increase, the plastic flow of materials is strengthened and the machined surface becomes rougher. However, as the cutting speed increases, the plastic flow of materials is weakened and the milled surface becomes smoother. The cutting parameters(e.g. cutting speed, feed per tooth and depth of cut)influencing the surface roughness are analyzed. It can be concluded that the roughness of the machined surface formed by the end cutting edge is less than that by the cylindrical cutting edge when a cylindrical flat-end mill tool is used for milling. The proposed research provides the typical topography features of machined surface of the anti-rust aluminum alloy Al Mn1 Cu in high speed milling.

Internal Friction and Elastic Study on Surface Nanocrystallized 304 Stainless Steel Induced by High-energy Shot Peening

The 304 stainless steel with nanostructured surface layer was successfully obtained by using the high-energy shot peening (HESP) method. The internal friction and Young's modulus of this kind of surface nanocrystallized material were dynamically measured by means of the vibrating reed apparatus. The results implied that different treatment time could induce different microstructure and distribution characteristic of defects in this kind of materials. It is also demonstrated that there is a transition layer between the nano-layer on surface and the coarse grain region inside. The transition layer obviously has certain influence on the overall mechanical properties.