High speed cutting of AZ31 magnesium alloy

Using LBR-370 numerical control lathe,high speed cutting was applied to AZ31 magnesium alloy.The influence of cutting parameters on microstructure,surface roughness and machining hardening were investigated by using the methods of single factor and orthogonal experiment.The results show that the cutting parameters have an important effect on microstructure,surface roughness and machine hardening.The depth of stress layer,roughness and hardening present a declining tendency with the increase of the cutting speed and also increase with the augment of the cutting depth and feed rate.Moreover,we established a prediction model of the roughness,which has an important guidance on actual machining process of magnesium alloy.

High Speed Cutting Inconel 718 with Coated Carbide and Ceramic Inserts

High speed machining (HSM) technology is one of important aspects of advanced manufacturing technology. Nickel-based superalloys have been widely used in the aircraft and nuclear industry due to their exceptional thermal resistance and the ability to retain mechanical properties at elevated temperatures of service environment over 700 ℃. However, they are classified as difficult-to-cut materials due to their high shear strength, work hardening tendency, highly abrasive carbide particles in the microstructure, strong tendency to weld and form built-up edge and low thermal conductivity. They have a tendency to maintain their strength at high temperature that is generated during machining. The Inconel 718 workpiece material used in the experiment was in the hot forged and annealed condition. The commercially available inserts (all inserts were made by Kennametal Inc.) were selected for the tests, a PVD TiAlN coated carbide, a CVD/PVD TiN/TiCN/TiN coated carbide and a CVD Al 2O 3/TiC/TiCN coated carbide were used at the cutting speed range about 50～100 m/min. Three kinds Sialon grade inserts with various geometry and cutting angles were used at the cutting speed range from 100 m/min to 300 m/min. For evaluating the inserts machinability when high speed cutting Inconel 718, Taylor Formula within certain cutting speeds, an high speed cutting experiment of tool life was carried out to establish the models of tool life by means of rapid facing turning test. The conclusions drawn from the turning of Inconel 718 with silicon nitride based ceramic; PVD and CVD coated carbide inserts are as follows: Studies on tool wear in high speed machining. The thorough investigations and studies were made on the tool wear form, wear process and wear mechanism in high speed cutting of difficult-to-machine materials with ceramic tools and with coated carbides. The major wear mechanisms of nickel-based alloys are interactions of abrasive wear, adhesion wear, micro-breakout and chipping. Optimization analysis on the application of high speed machining. Based on the experimental results, the optimal cutting parameters were determined for machining of Inconel 718 at high speed. The recommendation of tool inserts for high speed cutting inconel 718 were ceramic inserts of KY2000 with negative rake angle and KY2100 with round type, the PVD coated carbide insert KC7310 was recommended for its lower price.

CUTTING REGULARITY AND DISCHARGE CHARACTERISTICS BY USING COMPOSITE COOLING LIQUID IN WIRE CUT ELECTRICAL DISCHARGE MACHINE WITH HIGH WIRE TRAVELING SPEED

The analysis of cutting regularity is provided through using and comparing two typical cooling liquids. It is proved that cutting regularity is greatly affected by cooling liquid＇s washing ability. Discharge characteristics and theoretic analysis between two electrodes are also discussed based on discharge waveform. By using composite cooling liquid which has strong washing ability, the efficiency in the first stable cutting phase has reached more than 200 mm^2/min, and the roughness of the surface has reached Ra〈0.8 μm after the fourth cutting with more than 50 mm^2/min average cutting efficiency. It is pointed out that cutting situation of the wire cut electrical discharge machine with high wire traveling speed （HSWEDM） is better than the wire cut electrical discharge machine with low wire traveling speed （LSWEDM） in the condition of improving the cooling liquid washing ability. The machining indices of HSWEDM will be increased remarkably by using the composite cooling liquid.

Tool wear during high speed turning in situ TiC_p/TiB_w hybrid reinforced Ti-6Al-4V matrix composite

Chipping, adhesive wear, abrasive wear and crater wear are prevalent for both the polycrystalline diamond （PCD） and the carbide tools during high speed turning of TiCp/TiBw hybrid reinforced Ti-6Al-4V （TC4） matrix composite （TMCs）. The combined effects of abrasive wear and diffusion wear caused the big crater on PCD and carbide tool rake face. Compared to the PCD, bigger size of crater was found on the carbide tool due to much higher cutting temperature and the violent chemical reaction between the Ti element in the workpiece and the WC in the tool. However, the marks of the abrasive wear looked much slighter or even could not be observed on the carbide tool especially when low levels of cutting parameters were used, which attributes to much lower hardness and smaller size of WC combined with more significant chemical degradation of carbide. When cutting TC4 using PCD tool, notch wear was the most significant wear pattern which was not found when cutting the TMCs. However, chipping, adhesive wear and crater wear were much milder when compared to the cutting of titanium matrix composite. Due to the absence of abrasive wear when cutting TC4, the generated titanium carbide on the PCD protected the tool from fast wear, which caused that the tool life for TC4 was 6-10 times longer than that for TMCs.

LOOK-AHEAD ALGORITHM FOR VELOCITY CONTROL BASED ON PARAMETERIZED CURVE INTERPOLATOR

To avoid suffering gouge and transient overshooting in high speed cutting machining, a novel parametefized curve interpolator model with velocity look-ahead algorithm is proposed. Based on a prearrangement step interpolation algorithm for parameterized curves and considering high curvature points, parameterized curve tool path is divided into acceleration segments and deceleration segments by look-ahead algorithm. Under condition of characteristics of acceleration and deceleration stored in control system, deceleration before high curvature points and acceleration after high curvature points are realized in real-time in high speed cutting machining. Based on new parameterized curve interpolator model with velocity look-ahead algorithm, a real cubic spline is machined simulativly. The simulation results show that velocity look-ahead algorithm improves velocity changing more smoothly.