Multifunctional interlayer with simultaneously capturing and catalytically converting polysulfides for boosting safety and performance of lithium-sulfur batteries at high-low temperatures

Lithium-sulfur(Li-S) batteries as extremely promising high-density energy storage devices have attracted extensive concern. However, practical applications of Li-S batteries are severely restricted by not only intrinsic polysulfides shuttle resulting from their concentration gradient diffusion and sluggish conversion kinetics but also serious safety issue caused by thermolabile and combustible polymer separators.Herein, it is presented for the first time that a robust and multifunctional separator with urchin-like Co-doped Fe OOH microspheres and multiwalled carbon nanotubes(MWCNTs) as an interlayer simultaneously achieves to suppress polysulfides shuttle as well as improves thermotolerance and nonflammability of commercial PP separator. Accordingly, Li-S batteries with modified separator exhibit remarkable performance in a wide range temperatures of-25–100 ℃. Typically, under 25 ℃, ultrahigh initial capacities of 1441 and 827.29 m A h g-1 at 1 C and 2 C are delivered, and remained capacities of 936 and 663.18 mA h g-1 can be obtained after 500 cycles, respectively. At 0.1 C, the S utilization can reach up to 97%. Significantly, at 1 C, the batteries also deliver an excellent performance with remained capacities of high to862.3, 608.4 and 420.6 m A h g-1 after 100, 300 and 450 cycles under 75, 0 and-25 ℃, respectively. This work provides a new insight for developing stable and safe high-performance Li-S batteries.

Development and performance evaluation of high temperature resistant strong adsorption rigid blocking agent

As drilling wells continue to move into deep ultra-deep layers,the requirements for temperature resistance of drilling fluid treatments are getting higher and higher.Among them,blocking agent,as one of the key treatment agents,has also become a hot spot of research.In this study,a high temperature resistant strong adsorption rigid blocking agent(QW-1)was prepared using KH570 modified silica,acrylamide(AM)and allyltrimethylammonium chloride(TMAAC).QW-1 has good thermal stability,average particle size of 1.46μm,water contact angle of 10.5.,has a strong hydrophilicity,can be well dispersed in water.The experimental results showed that when 2 wt%QW-1 was added to recipe A(4 wt%bentonite slurry+0.5 wt%DSP-1(filtration loss depressant)),the API filtration loss decreased from 7.8to 6.4 m L.After aging at 240.C,the API loss of filtration was reduced from 21 to 14 m L,which has certain performance of high temperature loss of filtration.At the same time,it is effective in sealing 80-100mesh and 100-120 mesh sand beds as well as 3 and 5μm ceramic sand discs.Under the same conditions,the blocking performance was superior to silica(5μm)and calcium carbonate(2.6μm).In addition,the mechanism of action of QW-1 was further investigated.The results show that QW-1 with amide and quaternary ammonium groups on the molecular chain can be adsorbed onto the surface of clay particles through hydrogen bonding and electrostatic interaction to form a dense blocking layer,thus preventing further intrusion of drilling fluid into the formation.

Effect of linear carboxylic ester on low temperature performance of LiMn_2O_4-graphite cells

To improve the low-temperature performances of Li-ion cells, three types of linear carboxylic ester-based electrolyte, such as EC/EMC/EA（1：1：2, mass ratio）, EC/EMC/EP（1：1：2, mass ratio） and EC/EMC/EB（1：1：2, mass ratio）, were prepared to substitute for industrial electrolyte（EC/EMC/DMC）. Then, 18650-type Li Mn2O4-graphite cells（nominal capacity of 1150 mA ·h） were assembled and studied. Results show that the cells containing three types of electrolyte are able to undertake 5C discharging current with above 93% capacity retention at-20 °C. Electrochemical impedance spectra show that the discharge capacity fading of Li-ion cells at low temperature is mainly ascribed to the charge transfer resistance increasing with temperature decreasing. In comparison, the cells containing electrolyte of 1.0 mol/L LiPF6 in EC/EMC/EA（1：1：2, mass ratio） have the highest capacity retention of 90% at-40 °C and 44.41% at-60 °C, due to its lowest charge-transfer resistance.

Effect of sintering temperature on cycling performance and rate performance of LiNi_(0.8)Co_(0.1)Mn_(0.1)O_2

LiNi0.8Co0.1Mn0.1O2 powder was prepared by mixing LiOH·H2O and co-precipitated Ni0.8Co0.1Mn0.1（OH）2 at a molar ratio of 1：1.05, followed by sintering at different temperatures. The effects of temperature on the morphology, structure and electrochemical performance were extensively studied. SEM and XRD results demonstrate that the sintering temperature has large influence on the morphology and structure and suitable temperature is very important to obtain spherical materials and suppresses the ionic distribution. The charge-discharge tests show that the electrochemical performance of LiNi0.8Co0.1Mn0.1O2 powders becomes better with the increase of temperature from 700 ℃ to 750 ℃ and higher temperature will deteriorate the performance. Although both of materials obtained at 750 ℃ and 780 ℃ demonstrate almost identical cyclic stability at 2C rate, which delivers 71.9%retention after 200 cycles, the rate performance of powder calcined at 780 ℃ is much poorer than that at 750 ℃. The XRD results demonstrate that the poor performance is ascribed to more severe ionic distribution caused by higher temperature.

Study on low temperature performance of Gussasphalt on steel decks with hard bitumen

Using a Hamburg wheel-track test device, the resistance to rutting of Gussasphalt is tested and compared. Gussasphalt with hard bitumen has good resistance to rutting. The related resistance abilities to cracking at low temperature of Gussasphalt are tested and compared through flexural experiments and the composite structure fatigue test with temperature dropping. Gussasphalt with high performance polymer modified bitumen has a longer fatigue life and a lower breaking temperature; they can be used in the future surfaces for steel bridge decks in Germany.

Impact of Illumination and Temperature Performance of Blanket-Inside Solar Greenhouse and CO_2 Enrichment on Cucumber Growth and Development

To evaluate the effects of solar greenhouse with different structure and CO2 enrichment on illumination and temperature performance of greenhouse and cucumber growth and development in the central region of Inner Mongolia, the research used traditional solar greenhouse （A） and blanket-inside solar greenhouse（B）, and set 4 treatments： AE （traditional solar greenhouse A with CO2 enrichment）, AN （traditional solar greenhouse A without CO2 enrichment）, BE （blanket-inside solar greenhouse B with CO2 enrichment） and BN （blanket-inside solar greenhouse B without CO2 enrichment）, to explore the influence of cucumber growth, photosynthetic property, quality and yield in different structure solar greenhouses with CO2 enrichment. The results showed that the illumination and temperature in blanket-inside solar greenhouse was superior to traditional solar greenhouse, and the average light intensity in blanket-inside solar greenhouse increased by 21.05%, compared with traditional solar greenhouse. Under the condition of same greenhouse structure, stem height ,average stem diameter, contents of soluble sugar, vitamin C, net photosynthetic rate and yield showed any significant difference between the treatments with CO2 enrichment or not. Under the condition of same CO2 concentration, BE cucumber average stem height, average stem diameter, contents of soluble sugar, net photosynthetic rate and yield in BE was higher than which in AE. Therefore, the optimization in structure of blanket-inside solar greenhouse remarkably improved illumination and temperature property, combining with CO2 enrichment as application technology, there was crucial significance to promote the greenhouse performance and improve the efficiency of greenhouse vegetable production.

Temperature Dependence of Performance of 6H-SiC Unipolar Power Devices

The temperature dependence of some performance of 6H SiC unipolar power devices is analyzed theoretically.By employing the temperature dependent ionization coefficient and mobility of a silicon carbide,the analytical expressions of the temperature dependent performance,such as breakdown characteristics and on resistance of 6H SiC unipolar power devices are derived in a closed form.The analytical results are compared with the experimental results,with good accordance found in the breakdown characteristics.

Performance of Sn-Cu Alloy Anode at Low Temperature

Sn-Cu alloy anode was prepared by pulsed electrodeposition for lithium ion batteries, and its electrochemical performance was tested at low temperature. When temperature decreased from 25℃ to -20℃, the Sn-Cu alloy anode provided the capacity retentions of 76% in the electrolyte of 1 mol/L LiBF4/EC＋EMC＋γBL and 51% in the electrolyte of 1 mol/L LiPF6/EC＋DMC＋DEC. Under the same conditions, the graphite anode presented the capacity retentions of only 41% and 18%, respectively. The Sn-Cu alloy anode showed better performance in the electrolyte of 1 mol/L LiBF4/EC＋EMC＋γBL than in the electrolyte of 1 mol/L LiPF6/EC＋DMC＋DEC, and kept much higher capacity retention than that of graphite at -20℃. The Sn-Cu alloy anode in the electrolyte of 1mol/L LiBF4/EC＋EMC＋γBL （1：1：1, volume ratio） is promising for low temperature application of lithium batteries.

The Effect of Thermal Exfoliation Temperature on the Structure and Supercapacitive Performance of Graphene Nanosheets

Graphene nanosheets(GSs) were prepared from graphite oxide by thermal exfoliation method. The effect of thermal exfoliation temperature on the structure and supercapacitive performance of GSs has been investigated. The results show that the GSs with pore sizes center around 4.0 nm. With an increase of thermal reduction temperature, the number of stacking layers and the structure disorder degree increase, while the oxygen-containing groups content, BET surface area,and electrical resistivity of GSs decrease. The results indicate that 673 K is the preferable thermal exfoliation temperature to acquire good supercapacitive performance. In this case, the GSs have the best supercapacitive performance(233.1 F g-1) in a 6 mol L-1KOH electrolyte. The prepared GSs at the preferable thermal exfoliation temperature have good rate performance and cycle stability.

Effects of Reduced Nocturnal Temperature on Performance and Behavior of Nursery Pigs

Previous studies suggested that pigs prefer lower environmental temperatures during nighttime compared to daytime. So reducing nocturnal temperature in nursery barns may not jeopardize performance or welfare of pigs, but can save energy for heating the barn. A study was conducted to investigate growth performance and behavioral response of nursery pigs to reduced nocturnal temperature. This study was conducted in four replicates, each utilizing 270 newly weaned pigs and lasting for 5 wk. Temperature setpoint in the control room （CON） was started at 30℃ and decreased by 2℃ per week. In the treatment room （RNT）, temperature setpoint was maintained same as in CON between 7：00 h and 19：00 h, and reduced by 8~C between 19：00 h and 7：00 h starting from d 5. Growth performance （15 pens/room, 9 pigs/pen, BW=（6.3±0.61） kg） was monitored for 5 wk, and behaviors in 6 pens in each room were video-recorded for 24 h 3 d after being exposed to the experimental temperature. Instantaneous scan sampling was performed to determine time budgets for standing, sitting, eating, drinking, belly nosing, three postures of lying, and huddling. Two focal pigs were continuously viewed to record duration and occurrence of eating and drinking. Reduced nocturnal temperature did not affect the growth performance of the pigs, time spent standing, sitting, total lying and eating or duration and frequencies of eating and drinking （all P〉0.10）. However, RNT increased time spent lying sternal （83 vs. 72%, P〈0.001） and number of pigs that were huddling （70 vs. 50% of lying pigs, P〈0.001）, and decreased time spent lying laterally （0.8 vs. 4.6%, P〈0.001）, lying half laterally （5.3 vs. 11.0%, P〈0.001）, and belly nosing （0.9 vs. 1.7%, P=0.01） during nighttime. These results indicate that nursery pigs adopted the posture of lying sternal and huddled together to reduce heat loss from their body surface to maintain thermal balance and growth performance in RNT. Such mild reduction in nocturnal temperature in the nursery barn can save energy for heating the barn without negative effects on performance and behavior of nursery pigs.

Effects of flaky rare earth oxide additives on the high temperature performance of nickel electrodes

Effects of flaky rare earth oxide additives including Er2O3,Tm2O3,and Yb2O3,Lu2O3 on high temperature and high rate discharge performance of nickel electrodes were investigated.The discharge efficiency at 0.2C reached 96% at 60 oC for electrodes with 1 at.% flaky rare earth oxides.The high rate discharge performance for electrodes with flaky rare earth oxides were improved significantly,for example,discharge efficiency at 5C improved from 50% to 70%.The results showed that the end charging potential of the ...

Physiological performance of three calcifying green macroalgae Halimeda species in response to altered seawater temperatures

The effects of seawater temperature on the physiological performance of three Halimeda species were studied for a period of 28 d.Five treatments were established for Halimeda cylindracea,Halimeda opuntia and Halimeda lacunalis,in triplicate aquaria representing a factorial temperature with 24°C,28°C,32°C,34°C and 36°C,respectively.The average Fv/Fm of these species ranged from 0.732 to 0.756 between 24°C and 32°C but declined sharply between 34°C(0.457±0.035)and 36°C(0.122±0.014).Calcification was highest at 28°C,with net calcification rates(Gnet)of(20.082±2.482)mg/(g·d),(12.825±1.623)mg/(g·d)and(6.411±1.029)mg/(g·d)for H.cylindracea,H.opuntia and H.lacunalis,respectively.Between 24°C and 32°C,the specific growth rate(SGR)of H.lacunalis(0.079%–0.110%d–1)was lower than that of H.cylindracea(0.652%–1.644%d–1)and H.opuntia(0.360%–1.527%d–1).Three Halimeda species gradually bleached at 36°C during the study period.Malondialdehyde(MDA)and proline levels in tissues of the three Halimeda were higher in 34–36°C than those in 24–32°C.The results indicate that seawater temperature with range of 24–32°C could benefit the growth and calcification of these Halimeda species,however,extreme temperatures above 34°C have negative impacts.The measured physiological parameters also revealed that H.cylindracea and H.opuntia displayed broader temperature tolerance than H.lacunalis.

Shrinkage Behavior of High Performance Concrete at Different Elevated Temperatures under Different Sealing Conditions

The shrinkage behavior of high performance cement concrete made from Portland cement, ultra fine granulated blast furnace slag and pulverized fly ash with addition of superplasticizer at different temperatures from ambient temperature to 120 ℃ under different seuliug conditions was investigated by means of length change measurement on cylindrical concrete specimens along with curing age. Results show that drying shrinkage deformations of titled concrete specimens increased rapidly as the curing temperature rose. The development of dryiing shrinkage deformatian can be efficiently controlled with the aid of aluminum tape sealing as compared with the unsealed specimens, especially when the curing temperature is below 60℃ , although it will increase dramatically when the curing temperature is elevated to above 90%＂ . Polymer coating on concrete specimens showed a similar effect on the control of drying shrinkage as the sealing operation with aluminum tape.

High Temperature Performances of Spherical Nickel Hydroxide with Additive Y_2O_3

The effect Of Y2O3 as additive to the positive electrode on the high-temperature performances of the Ni-MH batteries was studied. The specific capacities of the positive electrode in Ni-MH battery at higher temperatures are much lower than usual. In order to improve high-temperature performances, charge/discharge curves of the Ni(OH)(2) electrodes with different amounts Of Y2O3 it different temperatures were studied. It is found that the specific capacities of the spherical Ni (OH)(2) with Y2O3 as additive are much higher than those of the regular at higher temperatures. The specific capacity of Ni (OH)(2) containing 1% Y2O3 at 0.2C C/D rate is 35% higher than that of the regular. The specific capacity of Ni (OH)(2) containing 0.2% Y2O3 at 1C C/D rate is 15% higher than that of the regular. Mechanism Of Y2O3 improving high temperature performances of Ni(OH)(2) electrode was also discussed in detail.

Effect of aggregate gradation on low temperature performance of asphalt paving mixtures

Low temperature cracking has become one of the important factors that diminish asphalt pavement's ride quality and service life.Especially in cold region,cracking caused by low temperature is the main distress form.This paper discussed the effect of aggregate gradation on the low temperature performance in asphalt paving mixtures.A total of 11 asphalt mixtures with 11 different aggregate gradations and one asphalt binder content were studied.Volumetric properties of the coarse aggregate and asphalt mixtures showed aggregate grading has a significant impact on the degree of aggregate interlock in asphalt mixtures.A trend is existed in the low temperature performance with the change of gradation.With the aid of mathematic statistics,it indicates gradation affects the low temperature performance significantly.The findings also indicate the relationship between the degree of aggregate interlock in asphalt mixtures and the low temperature performance:With the stone-to-stone contact developed,the mixture has a high energy to resist contract and deformation at low temperature.The properties of fine aggregate and asphalt play an important part in resisting low temperature cracking in floating structure.But it provides lower energy to resist low temperature cracking compared to the skeleton structure.

Experimental Performance of Moderate and High Temperature Heat Pump Charged with Refrigerant Mixture BY-3

Theoretical and experimental analysis of a new refrigerant mixture BY-3 was conducted based on a single-stage vapor compression refrigeration system. The water-water heat pump system used BY-3 to produce hot water when the low temperature was 20 ℃. The following results were obtained: the highest temperature at the condenser outlet reached about 85 ℃; when the difference between the water temperatures at the condenser outlet and the evaporator inlet was less than 40 ℃, the coefficient of performance (COP) was larger than 4; when the difference reached 55 ℃, the COP still kept 3; the discharge temperature of BY-3 was lower than 100 ℃, and the refrigerant vapor pressure kept lower than 1.8 MPa. When the water temperature at the condenser outlet reached over 85 ℃, nearly a 5 ℃ superheating temperature was maintained.

Comprehensive Analysis of High Temperature Performance of SBS-modified Asphalt Mixture

Evaluation of high temperature performance of SBS-modified asphalt mixture was presented.Both wheel loaded method and creep method were adopted for two different mixtures and two kinds of specimens with different height,and corresponding indicators were measured.Meanwhile,the correlation between these indicators was thoroughly analyzed and two kinds of mixtures were compared.The experimental results show that there is a good linear relationship between LWT indicators and CT indicators for M-13,while a relatively poor relationship for M-25,especially that between dynamic stiffness and static stiffness and that between dynamic stability and static creep stiffness.Besides,logarithmic relationship between DS and RD has a higher determination coefficient than that for linear relationship.Thus,multi-index evaluation should be taken for synthetically assessing high temperature performance of asphalt mixture.

High-temperature electrochemical performance and phase composition of Ti_(0.7) Zr_(0.5) V_(0.2) Mn_(1.8-x)Ni_x hydrogen storage electrode alloys

The rapid development of electric vehicles demands the development of high performance nickel metal hydride battery that is able to endure high temperature. The discharge properties of Ti 0.7 Zr 0.5 V 0.2 Mn 1.8- x Ni x ( x =0.4, 0.8, 1.1, 1.4, 1.7)hydrogen storage alloys was investigated and its phase composition was analyzed using X ray diffraction. The results show that the cycling life was improved as the content of nickel increases. When x =0.4, 0.8, 1.1 and 1.4, the main phase is MgZn 2 type C14 Laves phase and the second one is cubic TiNi phase. When x =1.7, the Laves phase structure disappears. EDAS analysis shows that the increase of nickel content is effective in suppressing the dissolution of vanadium component in alloys. [

Effect of irradiation on temperature performance of dispersioncompensation no-core cascade optical-fiber sensor coated with polydimethylsiloxane film

A temperature measurement device can produce data deviations and can even be damaged in a high-dose radiation environment.To reduce the radiation damage to such a device and improve the temperature measurement accuracy in a radiation environment,a temperature sensor based on optical-fiber sensing technology is proposed.This sensor has a cascade structure composed of a single-mode fiber(SMF),a dispersion-compensation fiber(DCF),a nocore fiber(NCF),and another SMF(SDNS).The DCF and NCF are coated with a polydimethylsiloxane(PDMS)film,which is a heat-sensitive material with high thermal optical and thermal expansion coefficients.In experiments,PDMS was found to produce an irradiation crosslinking effect after irradiation,which improved the temperature sensitivity of the SDNS sensor.The experimental results showed that within a range of 30–100℃,the maximum temperature sensitivity after irradiation was 62.86 pm/℃,and the maximum transmission sensitivity after irradiation was 3.353×10^(-2)dB/℃,which were 1.22 times and 2.267 times the values before irradiation,respectively.In addition,repeated temperature experiments verified that the SDNS sensor coated with the PDMS film had excellent temperature repeatability.Furthermore,it was found that with an increase in the irradiation intensity,the irradiation crosslinking degree of PDMS increased,and the temperature sensitivity of the sensor was improved.The proposed sensor could potentially be applied to temperature measurement in a nuclear-radiation environment.

The Temperature Variation of a Solar Cell in Relation to Its Performance

The temperature of a solar cell subjected to the incident global solar radiation as a function of the local day time is determined. A heat balance equation is solved considering the heat losses due to convection and thermal radiation. The cell efficiency is estimated as a measure of its performance. The results reveal that the temperature within the cell attains significant values. Nevertheless, the temperature dependence of its efficiency along the day time is not pronouncing. It slightly decreases with temperature.