Preparation of high-purity straight silicon nanowires by molten salt electrolysis

Silicon nanowires of high purity and regular morphology are of prime importance to ensure high specific capacities of lithium-ion batteries and reproducible electrode assembly process.Using nickel formate as a metal catalyst precursor,straight silicon nanowires(65–150 nm in diameter)were directly prepared by electrolysis from the Ni/SiO2 porous pellets with 0.8 wt%nickel content in molten CaCl2 at 900℃.Benefiting from their straight appearance and high purity,the silicon nanowires therefore offered an initial coulombic efficiency of 90.53% and specific capacity of 3377 m Ah/g.In addition,the silicon nanowire/carbon composite exhibited excellent cycle performance,retaining 90.38%of the initial capacity after 100 cycles.Whilst further study on the charge storage performance is still ongoing,these preliminary results demonstrate that nickel formate is an efficient and effective metal catalyst precursor for catalytic preparation of high purity straight silicon nanowires via the molten salt electrolysis,which is suitable for large-scale production.

Multiple factors influencing high-purity indium electrolytic refining

The effects of various contaminants in the electrolytic refinement of indium were investigated using a glow discharge mass spectrometer(GDMS).The effects of several factors such as the indium ion(In3+)concentration,the sodium chloride(NaCl)concentration,the current density,the gelatin concentration,the pH,and the electrode distance,were examined.Significant variations in impurity levels concerning gelatin concentration were observed.Both the gelatin and In3+concentration were moderately positively correlated with the Pb content.The Sb concentration was associated positively with the NaCl concentration,while the Ti concentration had an adverse correlation with the NaCl concentration.The Bi element content was positively linked to the electrode distance.As the current density increased,Cu,Pb,and Bi impurities initially rose and then eventually declined.Notably,a critical current density of 45 A·m^(-2) was identified in this behavior.

Polydopamine-modified metal-organic frameworks nanoparticles enhance the corrosion resistance and bioactivity of polycaprolactone coating on high-purity magnesium

Biodegradable magnesium(Mg)and its alloys exhibit excellent biocompatibility and mechanical compatibility,demonstrating tremendous potential for applications in orthopedics.However,the rapid degradation rate has limited their clinical application.Polycaprolactone(PCL)is commonly employed as a polymer coating to impede the rapid degradation of Mg.Unfortunately,its long-term anti-corrosion capability and bioactivity are inadequate.To address these issues,polydopamine(PDA)-modified zeolitic imidazolate framework-8(PZIF-8)bioactive nanoparticles are fabricated and incorporated into the PCL coating.The PZIF-8 particles,featuring catechol motifs,can enhance the compactness of the PCL coating,reduce its defects,and possess biomineralization ability,thereby effectively improving its anti-corrosive and bioactive properties.Moreover,the active substances released from the degradation of the PZIF-8 particles such as Zn^(2+)and PDA are beneficial for osteogenesis.The corrosion tests indicate that the corrosion current density of PCL-treated sample decreases by more than one order of magnitude and the amount of H_(2)released decreases from 0.23±0.12 to 0.08±0.08 ml cm^(-2)after doping with the PZIF-8.Furthermore,the improved corrosion resistance and released PDA and Zn^(2+)from the coating can promote osteogenic differentiation by up-regulating the expression of alkaline phosphatase activity,related osteogenic genes,and proteins.In addition,in vivo implantation experiments in rabbit femur defects further offer strong evidence that the doping of PZIF-8 nanoparticles accelerates bone reconstruction of the PCL coating.In summary,this work implies a new strategy to fabricate a PCL-based coating on Mg-based implants by introducing the PZIF-8 particles for orthopedic applications.

Enhanced recovery of high-purity Fe powder from iron-rich electrolytic manganese residue by slurry electrolysis

Iron-rich electrolytic manganese residue(IREMR)is an industrial waste produced during the processing of electrolytic metal manganese,and it contains certain amounts of Fe and Mn resources and other heavy metals.In this study,the slurry electrolysis technique was used to recover high-purity Fe powder from IREMR.The effects of IREMR and H2SO4 mass ratio,current density,reaction temper-ature,and electrolytic time on the leaching and current efficiencies of Fe were studied.According to the results,high-purity Fe powder can be recovered from the cathode plate,and the slurry electrolyte can be recycled.The leaching efficiency,current efficiency,and purity of Fe reached 92.58%,80.65%,and 98.72wt%,respectively,at a 1:2.5 mass ratio of H2SO4 and IREMR,reaction temperature of 60℃,electric current density of 30 mA/cm^(2),and reaction time of 8 h.In addition,vibrating sample magnetometer(VSM)analysis showed that the coercivity of electrolytic iron powder was 54.5 A/m,which reached the advanced magnetic grade of electrical pure-iron powder(DT4A coercivity standard).The slurry electrolytic method provides fundamental support for the industrial application of Fe resource recovery in IRMER.

Artificial neural network-based method for discriminating Compton scattering events in high-purity germaniumγ-ray spectrometer

To detect radioactive substances with low activity levels,an anticoincidence detector and a high-purity germanium(HPGe)detector are typically used simultaneously to suppress Compton scattering background,thereby resulting in an extremely low detection limit and improving the measurement accuracy.However,the complex and expensive hardware required does not facilitate the application or promotion of this method.Thus,a method is proposed in this study to discriminate the digital waveform of pulse signals output using an HPGe detector,whereby Compton scattering background is suppressed and a low minimum detectable activity(MDA)is achieved without using an expensive and complex anticoincidence detector and device.The electric-field-strength and energy-deposition distributions of the detector are simulated to determine the relationship between pulse shape and energy-deposition location,as well as the characteristics of energy-deposition distributions for fulland partial-energy deposition events.This relationship is used to develop a pulse-shape-discrimination algorithm based on an artificial neural network for pulse-feature identification.To accurately determine the relationship between the deposited energy of gamma(γ)rays in the detector and the deposition location,we extract four shape parameters from the pulse signals output by the detector.Machine learning is used to input the four shape parameters into the detector.Subsequently,the pulse signals are identified and classified to discriminate between partial-and full-energy deposition events.Some partial-energy deposition events are removed to suppress Compton scattering.The proposed method effectively decreases the MDA of an HPGeγ-energy dispersive spectrometer.Test results show that the Compton suppression factors for energy spectra obtained from measurements on ^(152)Eu,^(137)Cs,and ^(60)Co radioactive sources are 1.13(344 keV),1.11(662 keV),and 1.08(1332 keV),respectively,and that the corresponding MDAs are 1.4%,5.3%,and 21.6%lower,respectively.

Valence states, impurities and electrocrystallization behaviors during molten salt electrorefining for preparation of high-purity titanium powder from sponge titanium

High-purity titanium powder was prepared by molten salt electrorefining from sponge titanium in NaCl-KCl-TiClx salts. The titanium valence, purity and electrocrystallization during electrolysis process were studied. The XPS analysis showed that the titanium valences are mainly ＋4, ＋3 and ＋2 at the earlier, medium and later stages of electrolysis, respectively. During the electrolysis process, the contents of impurities Si, Cr, Mn, Al vary little, and the contents of impurities Fe, Cu, Ni decrease markedly, while the contents of impurities O, N, H increase obviously. The residual impurities are usually distributed in small tunnel of dendritic crystals. Enhancing the electrolysis temperature and prolonging the electrolysis time can increase the titanium particle size. The TEM analysis showed that the electrodeposited titanium is not a single crystal, but contains many nanostructured grains and subgrains, with grain size of 100-500 nm. The electrolysis mechanisms were also discussed.

Timing of granite pegmatite-type high-purity quartz deposit in the Eastern Qinling,China:constraints from in-situ LA-ICP-MS trace analyses of quartz and monazite U–Pb dating

Eastern Qinling,China is one of the important rare metal metallogenic provinces with extensively distributed granite pegmatite dikes.The No.5 granite pegmatite intruded into the granitic gneiss of the Qinling Group,and the major minerals are quartz(39.8%),K-feldspar(18.8%),albite(36.3%),muscovite(3.4%),and garnet(1.1%).Monazite U–Pb isotopic dating indicates that the No.5 pegmatite from the Eastern Qinling was emplaced at ca.420.2±2.2 Ma,which confirms that highpurity quartz mineralization probably formed during the Early Devonian.In-situ laser ablation inductively coupled plasma mass spectrometry analysis of quartz show that quartz samples from Eastern Qinling have total trace element concentrations(Al,Ti,Sc,Li,B,Cr,Mn,and Fe)ranging from 23.2 to 52.8 ppm,slightly higher than the quartz(impurity element content from 13.4 to 25.9 ppm)of the Spruce Pine high-purity quartz deposit in western North Carolina.The No.5 pegmatite of Eastern Qinling could be defined as one high-purity quartz deposit of China.

Preparing high-purity iron by direct reduction?smelting separation of ultra-high-grade iron concentrate

A new process for preparing high-purity iron(HPI)was proposed,and it was investigated by laboratory experiments and pilot tests.The results show that under conditions of a reduced temperature of 1075°C,reduced time of 5 h,and CaO content of 2.5wt%,a DRI with a metallization rate of 96.5%was obtained through coal-based direct reduction of ultra-high-grade iron concentrate.Then,an HPI with a Fe purity of 99.95%and C,Si,Mn,and P contents as low as 0.0008wt%,0.0006wt%,0.0014wt%,and 0.0015wt%,respectively,was prepared by smelting separation of the DRI using a smelting temperature of 1625°C,smelting time of 45 min,and CaO content of 9.3wt%.The product of the pilot test with a scale of 0.01 Mt/a had a lower impurity content than the Chinese industry standard.An HPI with a Fe purity of 99.98wt%can be produced through the direct reduction?smelting separation of ultra-high-grade iron concentrate at relatively low cost.The proposed process shows a promising prospect for application in the future.

Synthesis and Characterization of High-purity Aluminum Titanate with Water Quenching Method

High-purity aluminum titanate was synthesized via a water quenching method with waste-residue in the aluminum factory and industrial TiO2 as the main raw materials, which belongs to the comprehensive utilization of solid wastes. Compared with the conventional method, it can reduce synthesis temperature, effectively inhibit decomposition and raise the content of AT; the addition of tiny silicon powder can improve the sintering and optimize the properties of AT. The crystalline phase structure and microstructure of each sample were characterized with XRD and SEM methods; the content of each crystalline phase in each sample was confirmed with Rietveld Quantification method; the properties of each sample were also tested. The experimental results showed that No. 4 is the optimum specimen, with the corresponding mass ratio of Al2O3/TiO2 to be 1.27 and the content of AT of 97.2 wt%. The addition of optimum tiny silicon powder is confirmed to be 8wt%; its corresponding bulk density is 2.63 g/cm^3, bending strength is 46.34 MPa, and the retention of one thermal vibration bending strength is 71.5%.

The Status Quo and Development Trend of High-purity Gold Sputtering Targets

This article gives a brief introduction to manufacturers and markets of sputtering targets as well as the manufacturing technology thereof. Then, it analyzes the application of high-purity gold sputtering targets in the fields of integrated circuit, information storage, flat panel display, etc. Based on the above, the article analyzes the processing development trend for the high-purity gold sputtering targets in aspects of ultra-high purity, manufacturing technology, analysis and testing technologies.

Flow stress behavior of high-purity Al-Cu-Mg alloy and microstructure evolution

The flow stress behavior of high-purity Al-Cu-Mg alloy under hot deformation conditions was studied by Gleeble-1500,with the deformation temperature range from 300 to 500 °C and the strain rate range from 0.01 to 10 s-1. From the true stress-true strain curve, the flow stress increases with the increasing of strain and tends to be constant after a peak value, showing dynamic recover, and the peak value of flow stress increases with the decreasing of deformation temperature and the increasing of strain rate.When the strain rate is 10 s-1 and the deformation temperature is higher than 400 °C, the flow stress shows dynamic recrystallization characteristic. TEM micrographs were used to reveal the evolution of microstructures. According to the processing map at true strain of 0.7, the feasible deformation conditions are high strain rate(>0.5 s-1) or 440-500 °C and 0.01-0.02 s-1.

Use of various MgO resources for high-purity Mg metal production through molten salt electrolysis and vacuum distillation

A green and effective electrolytic process was developed to produce high-purity Mg metal using primary and secondary resources containing Mg O as a feedstock. The electrolysis of various Mg O resources was conducted using a Cu cathode in MgF2– LiF – KCl molten salt at 1043 K by applying an average current of 1.44 A for 12.5 h. The electrolysis of calcined North Korean magnesite and seawater Mg O clinker yielded Mg alloys of MgCu2and(Cu) phases with current efficiencies of 89.6–92.4%. The electrolysis of oxidized Mg O-C refractory brick, aged ferronickel slag, and ferronickel slag yielded Mg alloys of MgCu2and(Cu) phases with current efficiencies of 59.3–92.3%. The vacuum distillation of Mg alloys obtained was conducted at 1300 K for 10 h to produce high-purity Mg metal. After vacuum distillation, Mg metal with a purity of above 99.994% was obtained. Therefore, this study demonstrates the feasibility of the production of high-purity Mg metal from various Mg O resources using a novel electrolytic process with a Cu cathode, followed by vacuum distillation.

Atomic Emission Spectrographic Analysis of High-purity Gallium with Prior Partial Dissolution of Matrix

An improved method has been developed for enriching and determining trace In,Pt,Sn,Co,Hg,Pb,Ni, Bi,Pd,Cu and Ag in high-purity gallium.Sample was treated by PDM(partial dissolution of matrix)with HCl(11mol/L)-HNO_3(0.5mol/L)to a small residue of which Ga was then removed by extraction with 1 ml isopropyl ether.The concentrated impurities were determined by AES procedure.The recoveries for the ele- ments at the range of 0.02～0.2 μg are 95～103％;the relative standard deviations for determined impurities overa rangeofn.10^(-7)～n·10^(-8)％ are 4.3～12％;the detection limit of most elements can reach n·10^(-7)～ n·10^(-8)％ level with the exception of Hg and Pt.This method has been successfully used to analyze many sam- ples sent by factories and institutes.

Minimizing pest aluminum in magnesium for the production of high-purity titanium

It is practically difficult to find titanium sponges with low and stable aluminum impurities on the market even though it is the precondition to prepare high-purity titanium. Analysis indicates that almost all the aluminum impurities in the titanium sponge are inherited from the magnesium used to reduce titanium tetrachloride. However, it remains elusive for decades why magnesium produced through the silicothermic reduction method contains a high content of aluminum impurities with large fluctuations. By recourse to thermodynamic calculations and comparative experiments, we demonstrate that fluorite, a material used as a catalyst in the silicothermic reduction method to produce magnesium, is the chief culprit for the pest aluminum and propose a mechanism to rationalize the observed phenomena. Our findings indicate that one practical way to produce qualified magnesium for the production of high-purity titanium is to abandon fluorite during the production of magnesium with the silicothermic reduction method.

基于In Silicon模拟消化的北极虾DPP-Ⅳ抑制肽活性分析

北极虾具有很高的营养价值,在食品领域已引起越来越多的关注。对北极虾蛋白进行In Silicon模拟消化获得寡肽,通过PeptideRanker活性评分及理化性质分析,从中筛选出具有潜在生物活性的寡肽。使用ToxinPred分析和BIOPEP-UWM生物活性预测,发现部分寡肽具有二肽基肽酶-Ⅳ(dipeptidyl peptidase-Ⅳ,DPP-Ⅳ)抑制活性,最终确定WFP(一种三肽,Trp-Phe-Pro)具有最优的DPP-Ⅳ抑制活性肽。分子对接表明,WFP和DPP-Ⅳ能够形成稳定的复合物,其结合能为-6.93 kcal/mol,进一步研究表明,WFP通过与DPP-Ⅳ S1、S2、S3三个活性口袋中的9个氨基酸残基发生相互作用而抑制其活性。本研究为阐释北极虾营养价值及生物活性肽的开发提供了理论依据。

Innovative Solutions for High-Performance Silicon Anodes in Lithium-Ion Batteries:Overcoming Challenges and Real-World Applications

Silicon(Si)has emerged as a potent anode material for lithium-ion batteries(LIBs),but faces challenges like low electrical conductivity and significant volume changes during lithiation/delithiation,leading to material pulverization and capacity degradation.Recent research on nanostructured Si aims to mitigate volume expansion and enhance electrochemical performance,yet still grapples with issues like pulverization,unstable solid electrolyte interface(SEI)growth,and interparticle resistance.This review delves into innovative strategies for optimizing Si anodes’electrochemical performance via structural engineering,focusing on the synthesis of Si/C composites,engineering multidimensional nanostructures,and applying non-carbonaceous coatings.Forming a stable SEI is vital to prevent electrolyte decomposition and enhance Li^(+)transport,thereby stabilizing the Si anode interface and boosting cycling Coulombic efficiency.We also examine groundbreaking advancements such as self-healing polymers and advanced prelithiation methods to improve initial Coulombic efficiency and combat capacity loss.Our review uniquely provides a detailed examination of these strategies in real-world applications,moving beyond theoretical discussions.It offers a critical analysis of these approaches in terms of performance enhancement,scalability,and commercial feasibility.In conclusion,this review presents a comprehensive view and a forward-looking perspective on designing robust,high-performance Si-based anodes the next generation of LIBs.

Present Situation and Prospects of High-purity Elements in China

1.IntroductionHigh-purity elements are the basic materials in electronics,communication,aerospace,atomicenergy and semiconductor material industries.Its development is a decisive factor for high-tech in-dustries.The high-purification of non-ferrous metals is of great significance.It conduces to determining

Production of high-purity Mg metal from dolomite through novel molten salt electrolysis and vacuum distillation

In this study,a novel Mg production process for producing high-purity Mg metal from dolomite was developed.When the electrolysis of calcined dolomite was conducted using Cu cathode and C anode in MgF_(2)–LiF molten salt at 1083–1173 K by applying an average current of 1.42–1.46 A for 9.50–21.0 h,the current efficiency of 66.4–88.6%was obtained.The produced Mg alloys consisted of MgCu_(2)and Cu(Mg)or MgCu_(2)and CuMg_(2)phases,depending on the Mg concentration in the Mg alloy.When the electrolysis of calcined dolomite was conducted in MgF_(2)–LiF–CaF_(2)molten salt at 1083 K,the current efficiency was 40.9–71.4%,owing to undesired reactions such as electroreduction of Ca^(2+)or/and CO_(3)^(2−)ions.Meanwhile,the current efficiency increased from 40.9%to 63.2%by utilizing a Pt anode,because the occurrence of CO_(3)^(2−)ions in the molten salt was prevented.After vacuum distillation of the obtained Mg alloys at 1300 K for 10 h,Mg metal with a purity of 99.9996–99.9998%was produced.Therefore,the feasibility of this novel process for the production of high-purity Mg metal from dolomite was demonstrated.

Production of high-purity hydrogen from paper recycling black liquor via sorption enhanced steam reforming

Environmentally friendly and energy saving treatment of black liquor(BL),a massively produced waste in Kraft papermaking process,still remains a big challenge.Here,by adopting a NieCaOeCa_(12)Al_(14)O_(33) bifunctional catalyst derived from hydrotalcite-like materials,we demonstrate the feasibility of producing high-purity H_(2)(~96%)with 0.9 mol H_(2) mol^(-1) C yield via the sorption enhanced steam reforming(SESR)of BL.The SESRBL performance in terms of H_(2) production maintained stable for 5 cycles,but declined from the 6th cycle.XRD,Raman spectroscopy,elemental analysis and energy dispersive techniques were employed to rationalize the deactivation of the catalyst.It was revealed that gradual sintering and agglomeration of Ni and CaO and associated coking played important roles in catalyst deactivation and performance degradation of SESRBL,while deposition of Na and K from the BL might also be responsible for the declined performance.On the other hand,it was demonstrated that the SESRBL process could effectively reduce the emission of sulfur species by storing it as CaSO_(3).Our results highlight a promising alternative for BL treatment and H_(2) production,thereby being beneficial for pollution control and environment governance in the context of mitigation of climate change.

Silicone oil as a corneal lubricant to reduce corneal edema and improve visualization during

AIM:To evaluate the efficacy and safety of silicone oil(SO)as a corneal lubricant to improve visualization during vitrectomy.METHODS:Patients who underwent vitreoretinal surgery were divided into two groups.Group 1 was operated on with initial SO(Oxane 5700)as a corneal lubricant.Group 2 was operated on with initial lactated ringer’s solution(LRS)and then replaced with SO as required.Fundus clarity was scored during the surgery.Fluorescein staining was performed to determine the damage to corneal epithelium.RESULTS:Totally 114 eyes of 114 patients were included.Single SO use maintained a clear cornea and provided excellent visualization of surgical image.In group 1,the fundus clarity was grade 3 in 41/45 eyes and grade 2 in 4/45 eyes.In group 2,corneal edema frequently occurred after initial LRS use.The fundus clarity was grade 3 in 19/69 eyes,2 in 37/69 eyes and 1 in 13/69 eyes(P<0.05).SO was applied in 29 eyes of initial LRS use with subsequent corneal edema,which eliminated the corneal edema in 26 eyes.Corneal fluorescein staining score in group 1 was 0 in 28 eyes,1 in 11 eyes and 2 in 6 eyes,and 40,20 and 9,respectively,in group 2(all P>0.05).CONCLUSION:The use of SO as a corneal lubricant is effective and safe for preserving and improving corneal clarity and providing clear surgical field during vitrectomy.