During the process of liquid forging, a host of hot cracking defects were found in the Al-CuMg-Zn aluminum alloy. Therefore, mechanical tests and analyses by optical microscope, scanning electron microscope, and X-ray...During the process of liquid forging, a host of hot cracking defects were found in the Al-CuMg-Zn aluminum alloy. Therefore, mechanical tests and analyses by optical microscope, scanning electron microscope, and X-ray diffraction were performed to research the influences of zinc, magnesium, and copper(three main alloying elements) on hot cracking tendency and mechanical properties. It was concluded that all the three alloying elements exerted different effects on the performances of newly designed alloys. And the impact of microstructures on properties of alloys was stronger than that of solution strengthening. Among new alloys, Al-5 Cu-4.5 Mg-2.5 Zn alloy shows better properties as follows: σb=327 MPa, δ=2.7%, HB=107 N/mm^2, and HCS=40.展开更多
The severity of the hot and humid conditions to which miners are exposed increases as the depth of the work site increases.This can cause heat stress that can greatly affect the health and safety of workers.To resolve...The severity of the hot and humid conditions to which miners are exposed increases as the depth of the work site increases.This can cause heat stress that can greatly affect the health and safety of workers.To resolve this,a cooling garment has been developed that uses an atmospheric discharge of liquid CO2 to create a cool microclimate with an average temperature of 12.5(±0.4)℃ beneath the garment.To evaluate the garment's cooling efficiency,19 male subjects participated in an experimental procedure.The two modes,cooling on and off,were compared.Significant physiological differences were found between the two modes after minute 27(p<0.05)until the end of the recovery phase for the heart rate(maximum difference of 10 beats per minute)and the internal body temperature(maximum difference of 0.33℃).It was found that the modes also affected the subjects'perceptions.The ON-mode was associated with better well-being and thermal comfort,and reduced humidity sensation.Perceptions of exertion were lower in the ON-mode condition from minute 2.The findings provide strong evidence of the ability of this cooling garment to reduce heat stress in hot and humid conditions similar to those encountered in deep mines.展开更多
There is an increasing trend for producing copper-containing steels, with copper being either a residual element from scraps or an intentional addition, i. e. , in weathering steel. The issue of surface hot shortness ...There is an increasing trend for producing copper-containing steels, with copper being either a residual element from scraps or an intentional addition, i. e. , in weathering steel. The issue of surface hot shortness occurs during the hot working of steels containing copper, and a significant amount of work has been performed on this topic. This paper provides a review of related studies on this phenomenon. The formation mechanism, as analyzed, is the liquid metal embrittlement caused by the liquid copper penetration into austenite grain boundaries at the metal surface, where the copper originates from the selective oxidation of the steel at high temperature. On the basis of the mechanism, more importance is placed on analyzing the effect on the phenomenon by varying the controlling factors, including the heating process, alloying additions, and deformation conditions. Possible solutions to the problem are finalized, and some further work must be performed in the future.展开更多
The liquid phase turbulent structure of an air-water bubbly horizontal flow in a circular pipe has been investigated experimentally. Three-dimensional measurements were implemented with two "X" type probes o...The liquid phase turbulent structure of an air-water bubbly horizontal flow in a circular pipe has been investigated experimentally. Three-dimensional measurements were implemented with two "X" type probes oriented in different planes, and local liquid-phase velocities and turbulent stresses were simultaneously obtained. Systematic measurements were conducted covering a range of local void fraction from 0 to 11.7%. The important experiment results and parametric trends are summarized and discussed.展开更多
基金Funded by the International Cooperation Project of the Ministry of Science and Technology of China(No.2014DFR50320)the National Natural Science Foundation of China(No.51174064).
文摘During the process of liquid forging, a host of hot cracking defects were found in the Al-CuMg-Zn aluminum alloy. Therefore, mechanical tests and analyses by optical microscope, scanning electron microscope, and X-ray diffraction were performed to research the influences of zinc, magnesium, and copper(three main alloying elements) on hot cracking tendency and mechanical properties. It was concluded that all the three alloying elements exerted different effects on the performances of newly designed alloys. And the impact of microstructures on properties of alloys was stronger than that of solution strengthening. Among new alloys, Al-5 Cu-4.5 Mg-2.5 Zn alloy shows better properties as follows: σb=327 MPa, δ=2.7%, HB=107 N/mm^2, and HCS=40.
基金funded by the Fonds de Recherche du QuébecNature et Technologies (FRQNT)
文摘The severity of the hot and humid conditions to which miners are exposed increases as the depth of the work site increases.This can cause heat stress that can greatly affect the health and safety of workers.To resolve this,a cooling garment has been developed that uses an atmospheric discharge of liquid CO2 to create a cool microclimate with an average temperature of 12.5(±0.4)℃ beneath the garment.To evaluate the garment's cooling efficiency,19 male subjects participated in an experimental procedure.The two modes,cooling on and off,were compared.Significant physiological differences were found between the two modes after minute 27(p<0.05)until the end of the recovery phase for the heart rate(maximum difference of 10 beats per minute)and the internal body temperature(maximum difference of 0.33℃).It was found that the modes also affected the subjects'perceptions.The ON-mode was associated with better well-being and thermal comfort,and reduced humidity sensation.Perceptions of exertion were lower in the ON-mode condition from minute 2.The findings provide strong evidence of the ability of this cooling garment to reduce heat stress in hot and humid conditions similar to those encountered in deep mines.
文摘There is an increasing trend for producing copper-containing steels, with copper being either a residual element from scraps or an intentional addition, i. e. , in weathering steel. The issue of surface hot shortness occurs during the hot working of steels containing copper, and a significant amount of work has been performed on this topic. This paper provides a review of related studies on this phenomenon. The formation mechanism, as analyzed, is the liquid metal embrittlement caused by the liquid copper penetration into austenite grain boundaries at the metal surface, where the copper originates from the selective oxidation of the steel at high temperature. On the basis of the mechanism, more importance is placed on analyzing the effect on the phenomenon by varying the controlling factors, including the heating process, alloying additions, and deformation conditions. Possible solutions to the problem are finalized, and some further work must be performed in the future.
基金Supported by the National Natural Science Foundation of China(Grant No.59995460)
文摘The liquid phase turbulent structure of an air-water bubbly horizontal flow in a circular pipe has been investigated experimentally. Three-dimensional measurements were implemented with two "X" type probes oriented in different planes, and local liquid-phase velocities and turbulent stresses were simultaneously obtained. Systematic measurements were conducted covering a range of local void fraction from 0 to 11.7%. The important experiment results and parametric trends are summarized and discussed.
