Circular impinging jet, which is widely used in accelerated control cooling （ACC） equipment to accelerate the cooling of hot rolled plates, is subject to breakup, and may result in undesirable cooling effect. Theref...Circular impinging jet, which is widely used in accelerated control cooling （ACC） equipment to accelerate the cooling of hot rolled plates, is subject to breakup, and may result in undesirable cooling effect. Therefore, the jet breakup should be avoided as possible in industrial production. The objective of this study is to find the relation of the processing parameters of the ACC equipment versus the breakup length of jet with weaker turbulence. To obtain quantitative findings, not only relative experimental study but also numerical simulation was carded out. For a weaker turbulent water jet, the breakup length increases with the increase of jet diameter, as well as with the jet velocity; jet diameter has a significant effect on the breakup length for a certain flow rate when compared with jet velocity; finally a suggested correlation of the jet breakup length versus jet Weber number is presented in this study.展开更多
Heat transfer was researched from a perspective of the industry application. On the basis of the first law of thermodynamics, the cooling efficiency was deduced from the change of enthalpy inside hot plate. The relati...Heat transfer was researched from a perspective of the industry application. On the basis of the first law of thermodynamics, the cooling efficiency was deduced from the change of enthalpy inside hot plate. The relationship between the cooling efficiency and its influencing parameters was regressed from plenty of data collected from the worksite and discussed in detail. The temperature profiles resulting from the online model and the model modified by regressed formulas were presented and compared. The results indicated that the control accuracy of the modified model was increased obviously.展开更多
The influence of hot rolling on the microstructure and subsequent mechanical characteristics of explosive-welded ferritic stainless steel （FSS）/carbon steel （CS） laminate was investigated. The results indicate tha...The influence of hot rolling on the microstructure and subsequent mechanical characteristics of explosive-welded ferritic stainless steel （FSS）/carbon steel （CS） laminate was investigated. The results indicate that by hot rolling, decarburization layer disappears and a uniform structure is gained in CS side, but ferrite grains and carbides in constituent FSS form an uneven band microstructure which is denser at superficial zone than near the interface. The transmission electron microscopy results indicate that the layers adhering to the interface show typical deformed microstructure features, i.e., stream-like strips and elongated grains in FSS plates, carbide precipitates and bended cementite fragments in CS plates; and high-density dislocations in both plates, With hot rolling, various mechanical strengths and hardness are increased, while the elongation percentage is diminished. Examination of fractographs from tensile tests reveals predominately small dimples for explosive-welded specimens, whereas both big dimples and cleavage fracture for rolled specimens. Stereomicroscopic fractographs taken on shear samples indicate that the surfaces of explosive-welded specimens exhibit uniform deformation, but uneven deformation is displayed for that of rolled specimens. These results indicate that hot rolling is beneficial to improve the strength of explosive-welded FSS/CS laminate but not good for enhancing its plasticity.展开更多
文摘Circular impinging jet, which is widely used in accelerated control cooling （ACC） equipment to accelerate the cooling of hot rolled plates, is subject to breakup, and may result in undesirable cooling effect. Therefore, the jet breakup should be avoided as possible in industrial production. The objective of this study is to find the relation of the processing parameters of the ACC equipment versus the breakup length of jet with weaker turbulence. To obtain quantitative findings, not only relative experimental study but also numerical simulation was carded out. For a weaker turbulent water jet, the breakup length increases with the increase of jet diameter, as well as with the jet velocity; jet diameter has a significant effect on the breakup length for a certain flow rate when compared with jet velocity; finally a suggested correlation of the jet breakup length versus jet Weber number is presented in this study.
基金National Natural Science Foundation of China (50634030)
文摘Heat transfer was researched from a perspective of the industry application. On the basis of the first law of thermodynamics, the cooling efficiency was deduced from the change of enthalpy inside hot plate. The relationship between the cooling efficiency and its influencing parameters was regressed from plenty of data collected from the worksite and discussed in detail. The temperature profiles resulting from the online model and the model modified by regressed formulas were presented and compared. The results indicated that the control accuracy of the modified model was increased obviously.
基金This research was funded by the National Natural Science Foundation of China under Grant No. U 1510131, the Key Research and Development Program of Shanxi Province under Grant Nos. 201603D121010 and 201603D111004 and Shanxi Young Scholars Program.
文摘The influence of hot rolling on the microstructure and subsequent mechanical characteristics of explosive-welded ferritic stainless steel （FSS）/carbon steel （CS） laminate was investigated. The results indicate that by hot rolling, decarburization layer disappears and a uniform structure is gained in CS side, but ferrite grains and carbides in constituent FSS form an uneven band microstructure which is denser at superficial zone than near the interface. The transmission electron microscopy results indicate that the layers adhering to the interface show typical deformed microstructure features, i.e., stream-like strips and elongated grains in FSS plates, carbide precipitates and bended cementite fragments in CS plates; and high-density dislocations in both plates, With hot rolling, various mechanical strengths and hardness are increased, while the elongation percentage is diminished. Examination of fractographs from tensile tests reveals predominately small dimples for explosive-welded specimens, whereas both big dimples and cleavage fracture for rolled specimens. Stereomicroscopic fractographs taken on shear samples indicate that the surfaces of explosive-welded specimens exhibit uniform deformation, but uneven deformation is displayed for that of rolled specimens. These results indicate that hot rolling is beneficial to improve the strength of explosive-welded FSS/CS laminate but not good for enhancing its plasticity.
