The hot deformation behavior of powder met- allurgical （PM） TiAI alloys was investigated on Gleeble- 3500 thermomechanical simulator, at a temperature range of 1050-1200 ℃ with an interval of 50℃ and a strain rate...The hot deformation behavior of powder met- allurgical （PM） TiAI alloys was investigated on Gleeble- 3500 thermomechanical simulator, at a temperature range of 1050-1200 ℃ with an interval of 50℃ and a strain rate range of 0.001-1.000 s-1. The results show that the flow stress of PM TiAI alloy is sensitive to deformation tem- perature and strain rate, the peak stress decreases with the increase in deformation temperature and decrease in strain rate, and dynamic recrystallization occurs during the hot compression. The deformation active energy was calcu- lated and the flow stress model during high-temperature deformation was established based on the Arrhenius equations and Zener-Hollomon parameter. The deformed microstructure consists of refined homogeneous γ and α2/γ grains.展开更多
The disproportionated phases of Nd Hx, Fe2B,and a-Fe from Nd2Fe14B were applied to prepare Nd Fe B magnets by two different routes. The results show that the route of annealing in horizontal vacuum sintering furnace c...The disproportionated phases of Nd Hx, Fe2B,and a-Fe from Nd2Fe14B were applied to prepare Nd Fe B magnets by two different routes. The results show that the route of annealing in horizontal vacuum sintering furnace cannot reach the purpose of complete recombination after the hot pressing and hot deformation process due to the lack of dehydrogenation channel. The route of applying low pressure of 4–25 MPa on the as-disproportionated green compact during the desorption recombination process in situ hot deformation in a spark plasma sintering（SPS）system can obtain completely recombined Nd Fe B magnet with good anisotropy and magnetic properties. The maximum magnetic properties,（BH）max= 201 kJ m^-3,Br= 1.142 T and Hcj= 469 k A m^-1, are obtained after being treated for 15 min at 750 ℃ under low pressure.展开更多
It is approved that grain boundary diffusion is an effective method to increase the coercivity of hot-deformed NdFeB magnet.In this paper,a new rare earth-free grain boundary diffusion source of hot-deformed magnet wa...It is approved that grain boundary diffusion is an effective method to increase the coercivity of hot-deformed NdFeB magnet.In this paper,a new rare earth-free grain boundary diffusion source of hot-deformed magnet was studied.AlCuZn powders blended with commercial NdFeB powders were hot-compacted to obtain fully dense magnets,hot-deformed into anisotropic magnets and finally annealed to gain better homogeneity.Initially,the influences of annealing temperature and time on the magnetic properties of the specimens were studied and the optimal parameters of 600℃ and 60 min were achieved.Then,by changing the proportions of AlCuZn grain boundary diffusion,the coercivity,remanence and maximum energy product of the hot-deformed NdFeB magnets were examined.The result showed that with 1.0 wt%AlCuZn grain boundary diffusion and annealing at 600℃ for 60 min,the coercivity rose from 828 to 987 kA·m^(-1) without deteriorating the remanence.Microstructural analysis confirmed that AlCuZn diffused into the intergranular boundaries and the magnet diffused with AlCuZn possessed finer grains than that of without AlCuZn grain boundary diffusion.展开更多
基金supported by the National Natural Science Foundation of China (Nos. 51301157 and 51105102)the National High Technology Research and Development Program (No. 2013AA031103)
文摘The hot deformation behavior of powder met- allurgical （PM） TiAI alloys was investigated on Gleeble- 3500 thermomechanical simulator, at a temperature range of 1050-1200 ℃ with an interval of 50℃ and a strain rate range of 0.001-1.000 s-1. The results show that the flow stress of PM TiAI alloy is sensitive to deformation tem- perature and strain rate, the peak stress decreases with the increase in deformation temperature and decrease in strain rate, and dynamic recrystallization occurs during the hot compression. The deformation active energy was calcu- lated and the flow stress model during high-temperature deformation was established based on the Arrhenius equations and Zener-Hollomon parameter. The deformed microstructure consists of refined homogeneous γ and α2/γ grains.
基金financially supported by the National Natural Science Foundation of China (No. 51171122)
文摘The disproportionated phases of Nd Hx, Fe2B,and a-Fe from Nd2Fe14B were applied to prepare Nd Fe B magnets by two different routes. The results show that the route of annealing in horizontal vacuum sintering furnace cannot reach the purpose of complete recombination after the hot pressing and hot deformation process due to the lack of dehydrogenation channel. The route of applying low pressure of 4–25 MPa on the as-disproportionated green compact during the desorption recombination process in situ hot deformation in a spark plasma sintering（SPS）system can obtain completely recombined Nd Fe B magnet with good anisotropy and magnetic properties. The maximum magnetic properties,（BH）max= 201 kJ m^-3,Br= 1.142 T and Hcj= 469 k A m^-1, are obtained after being treated for 15 min at 750 ℃ under low pressure.
基金This study was financially supported by the National Key Research and Development Program(No.2016YFB0700902).
文摘It is approved that grain boundary diffusion is an effective method to increase the coercivity of hot-deformed NdFeB magnet.In this paper,a new rare earth-free grain boundary diffusion source of hot-deformed magnet was studied.AlCuZn powders blended with commercial NdFeB powders were hot-compacted to obtain fully dense magnets,hot-deformed into anisotropic magnets and finally annealed to gain better homogeneity.Initially,the influences of annealing temperature and time on the magnetic properties of the specimens were studied and the optimal parameters of 600℃ and 60 min were achieved.Then,by changing the proportions of AlCuZn grain boundary diffusion,the coercivity,remanence and maximum energy product of the hot-deformed NdFeB magnets were examined.The result showed that with 1.0 wt%AlCuZn grain boundary diffusion and annealing at 600℃ for 60 min,the coercivity rose from 828 to 987 kA·m^(-1) without deteriorating the remanence.Microstructural analysis confirmed that AlCuZn diffused into the intergranular boundaries and the magnet diffused with AlCuZn possessed finer grains than that of without AlCuZn grain boundary diffusion.
