Safety estimation of high-pressure hydraulic cylinder using FSI method

Hydraulic cylinder is a primary component of the hydraulic valve systems.The numerical study of hydraulic cylinder to evaluate the stress analysis,the life assessment and the performance of operation characteristics in hydraulic cylinder were described.The calculation of safety factor,fatigue life,piston chamber pressure,rod chamber pressure and the change of velocity of piston with flow time after the beginning of hydraulic cylinder were incorporated.Numerical analysis was performed using the commercial CFD code,ANSYS with unsteady,dynamic mesh model,two-way FSI(fluid-structure interaction)method and k-εturbulent model.The internal pressure in hydraulic cylinder through stress analysis show higher than those of the yield strength.

Analysis and Optimization of Inside-Cushion Structure in High-Speed Hydraulic Cylinders

An inside-cushion structure with sidestep and taper-shaped plungers is studied to address the problems of high impact and vibration in high-speed hydraulic cylinders.First,the three stages of cushion processes are discussed according to the varying flow area as the piston moves.Then,to establish a precise mathematical model,the states of the flow field are estimated in terms of the Reynolds number.Accordingly,the simulation model parameterized against measured data is developed and verified by experiment.Last,the average velocity,peak cushion pressure,and terminal velocity are defined to evaluate cushion performance.According to these optimized objectives,the non-linear programming by quadratic Lagrange(NLPQL)algorithm is applied to optimize the structure parameters.The optimization results indicate that the peak cushion pressure is reduced by 28%and terminal velocity is reduced by 21%without reduction of average velocity.

Trajectory synchronization of multi-cylinder electrohydraulic lift system with huge load

A kind of four degree-of-freedom （DOF） electrohydraulic lift system is studied in this pa- per, after analyzing the motion characteristics and the mathematic model of the hydraulic cylinders, a cross-coupled synchronization method with load force and synchronization error feedback had been proposed to solve the synchronization problem encountered when realizing the needed roll and pitch attitude of the lift system. In this paper, mathematic model of asymmetric hydraulic cylinder was es- tablished and the lift system had been simplified to a dual-cylinder system. By incorporating the load force and the displacement of each cylinder, a cross-coupled synchronized control method was pro- posed to fit each cylinder＇ s tracking performance and multi-cylinder＇ s trajectory synchronization property. The proposed method not only solved the synchronization problem when multi-cylinder had a same trajectory, but also could fit the coordinated synchronization need when different trajectories of multi-cylinder were desired. Simulations and experiments on a four DOF electrohydraulic lift sys- tem with load of 100 tons verified the effectiveness of the proposed method.

A design constraint for a double-acting telescopic hydraulic cylinder in a hydraulic erecting system

Hydraulic erecting systems are widely used in missile and rocket launchers because of their high power density.The double-acting telescopic hydraulic cylinder(DATHC)plays a decisive role in the safe and proper operation of such systems.In particular,improper design of effective areas of a DATHC could potentially lead to an overspeed descent with severe damage for the erecting system.Unfortunately,there is no design constraint for DATHC to prevent this.Therefore,in this paper,a simplified and practical design constraint is proposed.Based on a developed mathematical model of a typical erecting system,we simulated and analyzed not only six cases meeting and not meeting the design constraint,but also the effectiveness of the design constraint under different loads.Experiments were then carried out under four cases.Simulation and experimental results validate the simplified design constraint,a constraint inequation guiding the design of diameters of effective areas for a DATHC.

Study on Oil Cavity Number of Hydrostatic Guide Sleeve of Electro-hydraulic Servo Cylinder

The electro-hydraulic servo drive hydraulic cylinder has many unique advantages, such as fast response, high load stiffness, high control power, strong anti-eccentric load ability and so on, so it has been widely used in industrial control. Based on the guide sleeve of hydrostatic seal of hydraulic cylinder, the reasonable number of oil chamber of guide sleeve is studied in this paper. ICEM CFD software and FLUENT simulation software are used to calculate and analyze the number of different oil chambers of guide sleeve of hydrostatic seal. The temperature field of piston rod with different moving speed, different initial pressure of oil chamber and oil film under different number of oil chambers is analyzed. The relationship between the pressure field and temperature field provides a better basis for optimizing the design of hydrostatic guide sleeve and helps to improve the servo drive cylinder.

Hydraulic Self Servo Swing Cylinder Structure Optimization and Dynamic Characteristics Analysis Based on Genetic Algorithm

The dynamic characteristics of hydraulic self servo swing cylinder were analyzed according to the hydraulic system natural frequency formula. Based on that,a method of the hydraulic self servo swing cylinder structure optimization based on genetic algorithm was proposed in this paper. By analyzing the four parameters that affect the dynamic characteristics, we had to optimize the structure to obtain as larger the Dm( displacement) as possible under the condition with the purpose of improving the dynamic characteristics of hydraulic self servo swing cylinder. So three state equations were established in this paper. The paper analyzed the effect of the four parameters in hydraulic self servo swing cylinder natural frequency equation and used the genetic algorithm to obtain the optimal solution of structure parameters. The model was simulated by substituting the parameters and initial value to the simulink model. Simulation results show that: using self servo hydraulic swing cylinder natural frequency equation to study its dynamic response characteristics is very effective.Compared with no optimization,the overall system dynamic response speed is significantly improved.

Dynamics of luffing motion of a hydraulically driven shell manipulator with revolute clearance joints

In this study,a modeling method for investigating the dynamic characteristics of a hydraulically driven shell manipulator with revolute clearance joints is presented.This model accounts for the effect of the clearance,the flexibility of the rotating beam,and the coupled dynamic characteristics of the hydraulic cylinder.A modified contact force model was developed to simulate the physical properties of realistic revolute joints with small clearances,heavy loads,and variable contact stiffnesses and damping coefficients with variations of the indentations.Considering the strong coupling relationship between the hydraulic cylinder and the flexible beam,a system equation of motion combining the state variables of the hydraulic cylinder and mechanical system was established.The complex nonlinear friction force of the hydraulic cylinder motion was constructed using a modified Lu Gre model,and the parameters of the friction model were identified using intelligent identification algorithms.Moreover,a test system for the shell manipulator was established to achieve experimental validation.Finally,the effects of the clearance size and the stiffness of the cylinder support on the dynamic response were investigated.

Full Power Hydraulic Brake System Based on Double Pipelines for Heavy Vehicles

The hydraulic caliper disc brake system with air-over-oil is widely adopted at present for heavy vehicles,which makes use of air pressure system propelling the hydraulic pressure system acting on friction plates divided and combined for braking.There are some disadvantages such as pneumatic components failure,dust polluted and produce lots of heat in hydraulic caliper disc brake system.Moreover,considering the demands of the high speed,heavy weight,heavy load and fast brake of heavy vehicles,the full power hydraulic brake system based on double pipelines for heavy vehicles is designed and analyzed in this paper.The scheme of the full power hydraulic brake system,in which the triloculare cylinder is controlled by dual brake valve,is adopted in the brake system.The full power hydraulic brake system can accomplish steering brake,parking brake and emergent brake for heavy vehicles.Furthermore,electronic control system that is responsible for coordinating the work of hydraulic decelerator and hydraulic brake system is developed for different speed brakes.Based on the analysis of the influence of composed unit and connecting pipeline on braking performance,the nonlinear mathematic model is established for the full power hydraulic brake system.The braking completion time and braking pressure in braking performance of the double-pipeline steering brake and parking brake are discussed by means of simulation experiments based on Matlab/Simulink,and the simulation results prove that the braking performance of steering brake and parking brake meets the designing requirement of the full power hydraulic brake system.Moreover,the test-bed experiments of the brake system for heavy vehicles are carried out.The experimental data prove that the braking performance achieves the goal of the design,and that the full power hydraulic brake system based on double pipelines can effectively enhance braking performance,ensure braking reliability and security for heavy vehicles.

Model Design and Development of a Telescopic Palm Fruit Harvester

This research paper presents a comprehensive conceptual design approach for the development of a telescopic machine system, which is portable and will provide a safe method of harvesting palm fruits. For this machine system development, the material for each component of the machine system was first selected, the boom length, maximum boom angle, force and stroke length of each hydraulic cylinder, the hydraulic pump pressure, base weight, permissible weight of the cutting system and power required were then calculated in the design analysis. Furthermore, from the calculated parameters, the model of the system was created using SolidWorks engineering software, the model was developed and tested. The result shows that the cutting time of the system for one bunch of palm fruit was longer when compared to conventional systems. It was concluded that though the machine is maintenance friendly and portable, further improvements in its design are necessary so as to develop a system that will give desirable economic output at a shorter time.