Micro-tubes manufactured by hydro-forming techniques have now been widely used in medical and microelectronics applica- tions. One of the difficulties in forming such parts is the control of localized necking in the i...Micro-tubes manufactured by hydro-forming techniques have now been widely used in medical and microelectronics applica- tions. One of the difficulties in forming such parts is the control of localized necking in the initial stages of the deformation/forming process. A lack of microstructural information causes conventional macro-mechanics finite element（FE） tools to break down when used to investigate the localized microstructure evolution and necking encountered in micro-forming. An effort has been made to create an integrated crystal plasticity finite element（CPFE） system that enables micro-forming process simulations to be carried out easily, with the important features in forming micro-parts captured by the model. Based on Voronoi tessellation and probability theory, a virtual GRAIN（VGRAIN） system is created for generating grains and grain boundaries for micro-materials. Numerical procedures are devel- oped to link the physical parameters of a material to the control variables in a Gamma distribution. A script interface is developed so that the virtual microstructure can be input to the commercial FE code, ABAQUS, for mesh generation. A simplified plane strain CPFE modeling technique is developed and used to capture localized thinning and failure features for hydro-forming of micro-tubes. Grains within the tube workpiece, their distributions and orientations are generated automatically by using the VGRAIN system. A set of crystal viscoplasticity constitutive equations are implemented in ABAQUS/Explicit by using the user-defined material subroutine, VUMAT. Lo- calized thinning is analyzed for different microstructures and deformation conditions of the material using the CPFE modeling technique. The research results show that locations of thinning in forming micro-tubes can be random, which are related to microstructure and grain orientations of the material. The proposed CPFE technique can be used to predict the locations of thinning in forming micro-tubes.展开更多
The process of soft-punch hydro-forming was use.d to form some workpieces. However, it has not been completely understood until now. In this paper, based on some primary experiments, in which cups have been tried unde...The process of soft-punch hydro-forming was use.d to form some workpieces. However, it has not been completely understood until now. In this paper, based on some primary experiments, in which cups have been tried under different working conditions with the soft-punch hydro-forming process, systematical know-how about why the LDR of a metal sheet is different, how working conditions influence qualities of a work-piece, and how the deformation takes place has been achieved when simulations are employed. All these results claim that the cup depth heavily weighs on the cup wall thinning rate, and a satisfied complex part can be achieved when the contacting time between the sheet and the female die is under our control well by a movable slider, which is fixed as the bottom of the female die.展开更多
The dome hydro-forming was studied theoretically and experimentally. The theoretical analysis shows that the process of dome hydro-forming can be divided into two stages, i.e., firstly forming a hemi-sphere and second...The dome hydro-forming was studied theoretically and experimentally. The theoretical analysis shows that the process of dome hydro-forming can be divided into two stages, i.e., firstly forming a hemi-sphere and secondly forming a hemi-toroidal. Theoretically, being larger than those in the outer area of a hemi-toroidal shell, the radial tensile stresses take place in the inner area where fracture is more likely to occur in the forming process. The required hydraulic pressure to form the dome should be determined by the deformation in the outer area, hitting about 12 MPa in theory. The experimental results show that the dome could be produced in one operation by hydro-forming which needs a hydraulic pressure of about 9 MPa. The experimental results prove to agree well with the theoretical analysis. In order to avoid wrinkling and fracture, the closing force acted on the die should be adjusted properly in accordance with the hvdraulic nressure.展开更多
The mechanically bonded CRA-lined pipe is developed to meet the need forcorrosion-resistant alloy steel pipe. Residual contact pressure at the interface of lined pipe isimportant factor that governs the quality of lin...The mechanically bonded CRA-lined pipe is developed to meet the need forcorrosion-resistant alloy steel pipe. Residual contact pressure at the interface of lined pipe isimportant factor that governs the quality of lined pipe. A simplified theoretical method ispresented to predict the residual contact pressure created by hydraulic pressure. The calculatingequation related hydro-forming pressure to the residual contact pressure between two metal faces isderived. And the validation of the proposed equation is accomplished by comparing its result tothose obtained by experimental investigation.展开更多
基金supported by the EuropeanFP6-IP Project"Integration of Manufacturing Systems for Mass-manufacture of Miniature/Micro-Products(MASMICRO)"
文摘Micro-tubes manufactured by hydro-forming techniques have now been widely used in medical and microelectronics applica- tions. One of the difficulties in forming such parts is the control of localized necking in the initial stages of the deformation/forming process. A lack of microstructural information causes conventional macro-mechanics finite element（FE） tools to break down when used to investigate the localized microstructure evolution and necking encountered in micro-forming. An effort has been made to create an integrated crystal plasticity finite element（CPFE） system that enables micro-forming process simulations to be carried out easily, with the important features in forming micro-parts captured by the model. Based on Voronoi tessellation and probability theory, a virtual GRAIN（VGRAIN） system is created for generating grains and grain boundaries for micro-materials. Numerical procedures are devel- oped to link the physical parameters of a material to the control variables in a Gamma distribution. A script interface is developed so that the virtual microstructure can be input to the commercial FE code, ABAQUS, for mesh generation. A simplified plane strain CPFE modeling technique is developed and used to capture localized thinning and failure features for hydro-forming of micro-tubes. Grains within the tube workpiece, their distributions and orientations are generated automatically by using the VGRAIN system. A set of crystal viscoplasticity constitutive equations are implemented in ABAQUS/Explicit by using the user-defined material subroutine, VUMAT. Lo- calized thinning is analyzed for different microstructures and deformation conditions of the material using the CPFE modeling technique. The research results show that locations of thinning in forming micro-tubes can be random, which are related to microstructure and grain orientations of the material. The proposed CPFE technique can be used to predict the locations of thinning in forming micro-tubes.
文摘The process of soft-punch hydro-forming was use.d to form some workpieces. However, it has not been completely understood until now. In this paper, based on some primary experiments, in which cups have been tried under different working conditions with the soft-punch hydro-forming process, systematical know-how about why the LDR of a metal sheet is different, how working conditions influence qualities of a work-piece, and how the deformation takes place has been achieved when simulations are employed. All these results claim that the cup depth heavily weighs on the cup wall thinning rate, and a satisfied complex part can be achieved when the contacting time between the sheet and the female die is under our control well by a movable slider, which is fixed as the bottom of the female die.
文摘The dome hydro-forming was studied theoretically and experimentally. The theoretical analysis shows that the process of dome hydro-forming can be divided into two stages, i.e., firstly forming a hemi-sphere and secondly forming a hemi-toroidal. Theoretically, being larger than those in the outer area of a hemi-toroidal shell, the radial tensile stresses take place in the inner area where fracture is more likely to occur in the forming process. The required hydraulic pressure to form the dome should be determined by the deformation in the outer area, hitting about 12 MPa in theory. The experimental results show that the dome could be produced in one operation by hydro-forming which needs a hydraulic pressure of about 9 MPa. The experimental results prove to agree well with the theoretical analysis. In order to avoid wrinkling and fracture, the closing force acted on the die should be adjusted properly in accordance with the hvdraulic nressure.
文摘The mechanically bonded CRA-lined pipe is developed to meet the need forcorrosion-resistant alloy steel pipe. Residual contact pressure at the interface of lined pipe isimportant factor that governs the quality of lined pipe. A simplified theoretical method ispresented to predict the residual contact pressure created by hydraulic pressure. The calculatingequation related hydro-forming pressure to the residual contact pressure between two metal faces isderived. And the validation of the proposed equation is accomplished by comparing its result tothose obtained by experimental investigation.
