Existing studies have focused on the behavior of the retaining wall equipped with expanded polystyrene(EPS)geofoam inclusions under semi-infinite surcharge loading rather than limited surcharge loading.In this paper,t...Existing studies have focused on the behavior of the retaining wall equipped with expanded polystyrene(EPS)geofoam inclusions under semi-infinite surcharge loading rather than limited surcharge loading.In this paper,the failure mode and the earth pressure acting on the rigid retaining wall with EPS geofoam inclusions and granular backfills(henceforth referred to as EPS-wall),under limited surcharge loading are investigated through two-and three-dimensional model tests.The testing results show that different from the sliding of almost all the backfill in the EPS-wall under semi-infinite surcharge loading,only an approximately triangular backfill slides in the wall under limited surcharge loading.The distribution of the lateral earth pressure on the EPS-wall under limited surcharge loading is non-linear,and the distribution changes from the increase of the wall depth to the decrease with the increase of the limited surcharge loading.An approach based on the force equilibrium of a differential element is developed to predict the lateral earth pressure behind the EPS-wall subjected to limited surcharge loading,and its performance was fully validated by the three-dimensional model tests.展开更多
The catalytic conversion of polystyrene (PS) was studied in the presence of the materials type HZSM-5, CeO<sub>2</sub>, 10% CeO<sub>2</sub>/HZSM-5 and 20% CeO<sub>2</sub>/HZSM-5, wh...The catalytic conversion of polystyrene (PS) was studied in the presence of the materials type HZSM-5, CeO<sub>2</sub>, 10% CeO<sub>2</sub>/HZSM-5 and 20% CeO<sub>2</sub>/HZSM-5, which were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD) and nitrogen adsorption at 77K. The catalytic tests were performed via thermogravimetric analysis (TG) at heating rates of 5, 10 and 20˚C min<sup>−1</sup> in a temperature range from 30˚C to 900˚C. For the tests, a ratio of 30% by mass of each catalytic material mixed with PS was used and the activation energy of the degradation process was determined by the Vyazovkin method. The obtained results showed that the addition of the catalyst to the PS in general reduced its degradation temperature. The 10% CeO<sub>2</sub>/HZSM-5 catalyst showed greater efficiency, as it resulted in lower activation energy for PS degradation. Thus, the combination of CeO<sub>2</sub> with HZSM-5 resulted in materials with potential for application in the catalytic degradation of polystyrene and the results indicate that the production of a composite material can be a good strategy to generate an increase in catalytic activity and a decrease in energy process activation.展开更多
Managing agricultural waste and expanded polystyrene (EPS) poses significant environmental and economic challenges. This study aims to create composites from millet husks, rice husks, and recycled EPS, using a manufac...Managing agricultural waste and expanded polystyrene (EPS) poses significant environmental and economic challenges. This study aims to create composites from millet husks, rice husks, and recycled EPS, using a manufacturing method that involves dissolving the polystyrene in a solvent followed by cold pressing. Various particle sizes and two binder dosages were investigated to assess their influence on the physico-mechanical properties of the composites. The mechanical properties obtained range from 2.54 to 4.47 MPa for the Modulus of Rupture (MOR) and from 686 to 1400 MPa for the Modulus of Elasticity in Bending (MOE). The results indicate that these composites have potential for applications in the construction sector, particularly for wood structures and interior decoration. Moreover, surface treatments could enhance their durability and mechanical properties. This research contributes to the valorization of agricultural and plastic waste as eco-friendly and economical construction materials.展开更多
Electrospinning is a simple technique used to fabricate polymeric nano-fibrous membranes.These nano-fibers have found a wide range of valuable applications in the biomedical field.However,it has not been utilized with...Electrospinning is a simple technique used to fabricate polymeric nano-fibrous membranes.These nano-fibers have found a wide range of valuable applications in the biomedical field.However,it has not been utilized with solid high explosives yet.Herein,the electrospinning technique has been used to fabricate polystyrene(PS)/1,3,5-trinitro-1,3,5-triazinane(RDX)composite nanofibers.The governed electrospinning parameters,voltage,distance from the collector,flow rate,mandrel rotating speed,time,and solution concentration,that greatly affect the morphology of the obtained nanofibers were optimized.The fabricated PS/RDX nano-fibers were characterized using scanning electron microscopy(SEM),X-ray diffractometer(XRD),and Fourier Transform Infrared(FTIR)spectroscopy.The impact and friction sensitivities of PS/RDX were also measured.The thermal behavior of the prepared composite and the pure materials were studied by the thermal gravimetric analysis technique(TGA).SEM results proved the fabrication of PS/RDX fibers in the nano-size via electrospinning.FTIR spectroscopy confirmed the existence of the characteristic functional groups of both PS and RDX in the composite nano-fibers.XRD sharp peaks showed the conversion of amorphous PS into crystalline shape via electrospinning and also confirmed the formation of PS/RDX composite.The PS fibers absorbed the heat and increased the onset decomposition of the pure RDX from 181.5 to 200.7℃in the case of PS/RDX fibers.Interestingly,PS/RDX nano-fibers showed the relatively low impact and friction sensitivities of 100 J and 360 N respectively.These results could introduce PS/RDX nanofibrous composite in the field of explosives detection with high levels of safety.展开更多
Thermo-responsive random copolymers,poly(2-(2-methoxyethoxy)ethoxyethyl methacrylate-co-(ethylene glycol)methyl ether methacrylate)(P(EO_(2)-co-EO_(4/5)))and poly(2-(2-methoxyethoxy)ethoxyethyl methacrylate-co-ethylen...Thermo-responsive random copolymers,poly(2-(2-methoxyethoxy)ethoxyethyl methacrylate-co-(ethylene glycol)methyl ether methacrylate)(P(EO_(2)-co-EO_(4/5)))and poly(2-(2-methoxyethoxy)ethoxyethyl methacrylate-co-ethylene glycol methacrylate(P(EO2-co-EG4/5))are synthesized via atom transfer radical polymerization(ATRP).The successful synthesis and the narrow polydispersity index(PDI)of two copolymers are indicated by 1H nuclear magnetic resonance(1H-NMR)and gel permeation chromatography(GPC)analyses.The transition behaviors of polymers in the aqueous solution are demonstrated by changes in turbidity and particle sizes.The transition behavior of P(EO2-co-EG4/5)is found to be milder than that of P(EO2-co-EO4/5).Moreover,the presence of hydrogen bonds without thermo-responsive properties established by hydroxyl groups in the end-side chain of P(EO_(2)-co-EG_(4/5))hinders the dehydration at the transition temperature(TT).Attenuated total reflection Fourier transform infrared spectrometry(ATR-FTIR)analysis along with contact angle measurements reveals that both P(EO_(2)-co-EO_(4/5))and P(EO_(2)-co-EG_(4/5))films undergo phase transitions from hydrophilicity to hydrophobicity above TT.By examining the swelling and collapse behaviors of the polymer films during phase transitions,it can be concluded that the end hydroxyl groups may establish hydrogen bonds with neighboring ether groups within the films,which remain intact throughout the phase transition process due to their strong bonding interactions.This leads to an increase in steric hindrance within swollen films thereby impeding dehydration processes and inducing hysteresis during phase transitions.展开更多
BACKGROUND Sodium polystyrene sulfonate(SPS)is commonly prescribed for the management of hyperkalemia,a critical electrolyte imbalance contributing to over 800000 annual visits to emergency departments.AIM To conduct ...BACKGROUND Sodium polystyrene sulfonate(SPS)is commonly prescribed for the management of hyperkalemia,a critical electrolyte imbalance contributing to over 800000 annual visits to emergency departments.AIM To conduct a systematic review of documented cases of SPS-induced colitis and assess its associated prognosis.METHODS Following the PRISMA-P guidelines,our study employed Medical Subject Headings and Health Sciences Descriptors,skillfully combined using Boolean operators,to conduct comprehensive searches across various electronic databases,including Scopus,Web of Science,MEDLINE(PubMed),BIREME(Biblioteca Regional de Medicina),LILACS(Latin American and Caribbean Health Sciences Literature),SciELO(Scientific Electronic Library Online),Embase,and Opengray.eu.Language criteria were confined to English,Spanish,and Portuguese,with no limitations on the publication date.Additionally,we manually scrutinized the reference lists of retrieved studies.To present our findings,we utilized simple descriptive analysis.RESULTS Our search strategy yielded a total of 442 references.After rigorous evaluation,we included 51 references,encompassing 59 documented cases of colitis.Predominant clinical presentations included abdominal pain,observed in 35(60.3%)cases,and bloating,reported in 18(31%)cases.The most frequently affected sites of inflammation were the cecum,rectum,and small intestine,accounting for 31%,25.8%,and 22.4%of cases,respectively.Colonoscopy findings were described in 28(48.2%)cases,and 29(50%)of patients required surgical intervention.Among the subset of patients for whom outcome data was available,39(67.2%)experienced favorable outcomes,while 12(20.6%)unfortunately succumbed to the condition.The mean time required for resolution was 36.7 d,with a range spanning from 1 to 120 d.CONCLUSION SPS demonstrates the capacity to effectively lower serum potassium levels within 24 h.However,this benefit is not without the risk of bowel injury.Our study highlights the absence of high-quality data pertaining to the incidence of adverse events associated with SPS usage,making it challenging to determine whether the potential risks outweigh the benefits.However,a significant mortality rate related to SPS-induced colitis was noted.Future investigations should prioritize randomized controlled trials with a sufficiently large patient cohort to ascertain the true utility and safety profile of this medication.展开更多
Chloromethylation of polystyrene (PS) with two different chloromethylating systems methylal/thionyl chloride and paraformaldehyde/trimethylchlorosilane was studied. Soluble chloromethylated polystyrene with a degree...Chloromethylation of polystyrene (PS) with two different chloromethylating systems methylal/thionyl chloride and paraformaldehyde/trimethylchlorosilane was studied. Soluble chloromethylated polystyrene with a degree of substitution of 89% was obtained. The Conant-Finkelstein reaction on the chloromethylated PS afforded soluble iodomethylated polystyrene with a degree of substitution as high as 96%. The reaction conditions of Minisci were employed to radically pyridinate PS via its iodomethylated derivative. Polyelectrolytes were formed which could be converted to normal polymers by treatment with a 20% aqueous solution of NaOH.展开更多
Atmospheric exposure tests including two experimental stages of high temperature-spraying water cycle and heating-refrigeration cycle were carried out on three currently used ETIS of expanded polystyrene(EPS) board,...Atmospheric exposure tests including two experimental stages of high temperature-spraying water cycle and heating-refrigeration cycle were carried out on three currently used ETIS of expanded polystyrene(EPS) board,polystyrene granule mortar and polyurethane foam in order to study the weatherablility of external thermal insulation system(ETIS).The change rules of adhesive strength were hereby studied at different time period of atmospheric exposure tests.The experimental results show that the adhesive strength of three kinds of ETIS changes a little during high temperature-spraying water cycle,but the adhesive strength of ETIS with EPS board decreases significantly after heating-refrigeration cycle.The lowering rate of adhesive strength with painting finishes is obviously faster than that of tile finishes for ETIS of EPS board during heating-refrigeration cycle.The weatherability of ETIS with EPS board is worse than the other two,and ETIS of polystyrene granule mortar and polyurethane foam are more suitable than ETIS of EPS board in cold area.展开更多
Fluorescent polystyrene(PS)/porphyrin(TPPA) composite nanospheres were successfully fabricated by electrospinning. The SEM images clearly show that owing to adding TPPA in PS, the averaged diameter of the composit...Fluorescent polystyrene(PS)/porphyrin(TPPA) composite nanospheres were successfully fabricated by electrospinning. The SEM images clearly show that owing to adding TPPA in PS, the averaged diameter of the composite nanospheres became smaller, from 1500 to 580 nm. Fourier-transform infrared(FTIR) spectra determined the chemical composition of the resulting PS/TPPA composite nanospheres. The photoluminescent(PL) spectral analysis indicates that the peak position of the composite nanospheres in either solid state or water is identical to that of pure TPPA, at about 652 nm, and is still unchangeable when they are left for at least 20 d, indicating the stable photoluminescent property of the fluorescent composite nanospheres.展开更多
In this paper, magnetic nanospheres coated with polystyrene (Fe3O4@PS) were prepared for the removal of organochlorine pesticides from aqueous solutions. The obtained Fe3O4@PS was round shape with diameter of 55...In this paper, magnetic nanospheres coated with polystyrene (Fe3O4@PS) were prepared for the removal of organochlorine pesticides from aqueous solutions. The obtained Fe3O4@PS was round shape with diameter of 55±11 nm. The VSM results illustrated that its higher saturated magnetization was 36.76 emu g^-1 and it could be easily separated from aqueous solutions with a permanent magnet. The adsorption results showed that pesticides could be effectively adsorbed and the adsorption equilibrium time was less than 20 mins. The pseudo-second-order model was suitable to describe the adsorption kinetics. Compared with the Freundlich adsorption model, the adsorption data fitted well with Langmuir model. The effect of salinity and humic acid was also studied and the results illustrated that they could be neglected under optimized conditions. The asobtained sorbent showed a good performance with more than 93.3% pesticides removal in treating actual water samples.展开更多
An experimental system for measuring the VLE of polymer solutions based on the staticvapor-pressure method has been established,VLE data for mixtures of toluene and polystyrene withdifferent molecular weight covering ...An experimental system for measuring the VLE of polymer solutions based on the staticvapor-pressure method has been established,VLE data for mixtures of toluene and polystyrene withdifferent molecular weight covering a wide range from 2.98×10~3 to 3.84×10~6 were obtained at 35℃.The reduced pressure p/p°versus weight fraction W plot is found to be independent on the molecularweight of the polymer within the experimental error.Calculated activity coefficients are also independenton the molecular weight.However,for the Flory-Huggins interaction parameter x,not only a strongconcentration dependence is observed,but also the molecular weight of the polymer exerts definiteinfluence.Generally,the parameter x slightly increases as the molecular weight of the polymer decreasesespecially when the molecular weight is low.The dependence of the parameter x on the molecularweight can be neglected when the molecular weight of polymer is greater than 1.00×10~4.展开更多
The highly ordered silver-coated colloidal crystals arrays and macroporous silver films were derived through an electrostatics-induced adsorption effect using polystyrene(PS) as templates. Carboxyl-modified PS microsp...The highly ordered silver-coated colloidal crystals arrays and macroporous silver films were derived through an electrostatics-induced adsorption effect using polystyrene(PS) as templates. Carboxyl-modified PS microspheres were prepared by emulsifier-free emulsion polymerization using methacrylic acid(MAA) as the functional monomer. PS microspheres were self-assembled into close packing colloidal crystals of facecentered cubic arrays to the substrate with vertical deposition method. These colloidal crystals were modified using dopamine(DA) to form poly-dopamine(PDA) during its oxidative polymerization. Through electrostatic interaction, the silver nanoparticles were deposited and adsorbed onto the surfaces of colloidal crystals templates by exposing [Ag(NH_3)_2]^+solution to infrared irradiation. Removal of the polymeric template by etching with methylbenzene solvent resulted in 3D ordered macroporous silver films. The structural and properties of the ordered silver-coated arrays and macroporous silver films were characterized by field emission scanning electron microscopy(FE-SEM), X-ray diffraction(XRD), UV-vis spectroscopy and surface-enhanced Raman spectroscopy(SERS). The results indicate that the prepared silver-coated arrays and macroporous silver films possess the features of ordered multilayer arrangement, uniformity and repeatability as well as an ideal SERS effect.展开更多
A facile and novel method for the production of a large area of well-ordered polystyrene (PS) colloidal crystal monolayer was established using the surfactant-free Langmuir-Blodgett (LB) technique. The hydrophobic...A facile and novel method for the production of a large area of well-ordered polystyrene (PS) colloidal crystal monolayer was established using the surfactant-free Langmuir-Blodgett (LB) technique. The hydrophobic property (film-forming ability) of PS spheres was improved by a thermo-rheology treatment before LB assembly, and a large film was obtained. In contrast to the traditional LB technique, no surfactant was needed in this method, which could eliminate the additional contamination of surfactants in the preparation process and provided the products with versa- tile applications in nanosphere lithography (NSL) for biosensor, surface plasmon resonance, and surface enhanced Raman spectroscopy .展开更多
In the present work,a study is made to investigate the effects of process parameters,namely,laser power,scanning speed,hatch spacing, layer thickness and powder temperature, on the tensile strength for selective laser...In the present work,a study is made to investigate the effects of process parameters,namely,laser power,scanning speed,hatch spacing, layer thickness and powder temperature, on the tensile strength for selective laser sintering( SLS) of polystyrene( PS). Artificial neural network( ANN) methodology is employed to develop mathematical relationships between the process parameters and the output variable of the sintering strength. Experimental data are used to train and test the network. The present neural network model is applied to predicting the experimental outcome as a function of input parameters within a specified range. Predicted sintering strength using the trained back propagation( BP) network model showed quite a good agreement with measured ones. The results showed that the networks had high processing speed,the abilities of error-correcting and self-organizing. ANN models had favorable performance and proved to be an applicable tool for predicting sintering strength SLS of PS.展开更多
Sulfonated syndiotactic polystyrene ionomers (SsPS) with 1.8 mol% degree of sulfonation have been studied. WAXD shows that the crystallinity of SsPS ionomers was decreased with increasing diameter size of the counter ...Sulfonated syndiotactic polystyrene ionomers (SsPS) with 1.8 mol% degree of sulfonation have been studied. WAXD shows that the crystallinity of SsPS ionomers was decreased with increasing diameter size of the counter ions and sPS > SsPS-H > SsPS-K > SsPS-Zn. Moreover, SsPS ionomers only have alpha crystal form, while original sPS has two crystal forms: alpha and beta crystal form. TGA shows that the thermal stability of SsPS ionomers is higher than that of the original sPS and SsPS-Zn > SsPS-K > SsPS-H. DSC shows that all the glass transition temperatures (T-g) of SsPS ionomers are higher than that of the neat sPS and SsPS-Zn > SsPS-Na > SsPS-K > SsPS-H. However, the melting temperature (T-m) and crystallization peak temperature (T-p) of SsPS ionomers are lower and SsPS-H > SsPS-Zn > SsPS-K > SsPS-Na, while the crystallinity (X-c) of SsPS-Zn is the lowest. Nonisothermal crystallization kinetics shows that the Avrami index of sPS and SsPS-H are both about 4, suggesting the nucleation growth of SsPS-H with lower degree of sulfonation still keeps its three-dimension form. FTIR spectra of SsPS ionomers show a splitting absorption band for asymmetric stretching vibration of sulfonation group. The CH in-plane bending vibration of benzene ring shifted to higher wavenumber and the symmetric stretching vibration of sulfonation group changed slightly with different counter ion neutralized SsPS ionomers.展开更多
Broadband Mie scattering is used to determine the parameters of polystyrene aerosol beads in air,such as size and wavelength dependence of refractive index.This method consists in the selection of such parameters of t...Broadband Mie scattering is used to determine the parameters of polystyrene aerosol beads in air,such as size and wavelength dependence of refractive index.This method consists in the selection of such parameters of the scattering object,which reproduce observed spectrum properties.That is why it is very sensitive and hence very precise.We found that there is an ambiguity of polystyrene aerosol beads properties,determined with this method.Different combinations of polystyrene particle size and its refractive index can give the same position of Mie resonances.This ambiguity leads to an increase in the error in determining the size and refractive index of the particle.The refined errors are calculated and the way of their reduction is indicated.展开更多
Arrays of noble metal nanoparticles show potential applications in (bio-)sensing, optical storage, surface-enhanced spectroscopy, and waveguides. For all such potential devices, controlling the size, morphology, and...Arrays of noble metal nanoparticles show potential applications in (bio-)sensing, optical storage, surface-enhanced spectroscopy, and waveguides. For all such potential devices, controlling the size, morphology, and interparticle spacing of the nanoparticles is very important. Here, we combine seed-mediated growth with nanosphere lithography to study the controllable growth of gold nanoparticles (Au NPs), in which the self-assembly monolayer of polystyrene (PS) on a silicon surface is used to guide the modification of allaunesilanes and the subsequent adsorption of gold seeds; seed-mediated growth is applied to controlling the morphology and size of Au NPs. The size of adsorption region (determining the number of adsorbed gold seeds) is controlled by etching PS microspheres with oxygen plasma or annealing PS microspheres at the glass transition temperature. The size and morphology of the Au NPs are controlled by changing growth conditions. In such a way, we have achieved the dual control of the obtained Au NPs. Preliminary results show that this strategy holds a great promise. This approach can also be extended to a wide range of materials and substrates.展开更多
The polystyrene/rectorite nanocomposites were prepared by free radical polymerization of styrene containing dispersed organophilic rectorite. The structures and thermal properties of these hybrids have been investigat...The polystyrene/rectorite nanocomposites were prepared by free radical polymerization of styrene containing dispersed organophilic rectorite. The structures and thermal properties of these hybrids have been investigated by X\|ray diffraction (XRD), fourier transform infrared (FT\|IR), positron annihilation spectroscopy (PAS) and thermal gravimetric analysis (TGA) techniques. It was found that exfoliation of rectorite in polystyrene (PS) matrix was achieved. The average free\|volume radius in the PS/clay nanocomposites is generally same as that in PS. Along with increment of rectorite contents, the interface between rectorite and polystyrene matrix increases, and the free\|volume concentration decreases obviously. And the polystyrene nanocomposites have higher thermal decomposition temperature than pure PS.展开更多
Microspheres coated with a perfectly conductive surface have many advantages in the applications of biosensors and micro-electromechanical systems. Polystyrene microspheres with the diameter of 10 μm were coated with...Microspheres coated with a perfectly conductive surface have many advantages in the applications of biosensors and micro-electromechanical systems. Polystyrene microspheres with the diameter of 10 μm were coated with a 50 nmthick gold layer using an electroless gold plating approach. Dielectrophoresis (DEP) for bare microspheres and shelled microspheres was theoretically analysed and the real part of the Clausius Mossotti factor was calculated for the two kinds of microspheres. The experiments on the dielectrophoretic characterisation of the uncoated polystyrene microspheres and gold coated polystyrene microspheres (GCPMs) were carried out. Experimental results showed that the gold coated polystyrene microspheres were only acted by a positive dielectrophoretic force when the frequency was below 40M Hz, while the uncoated polystyrene microspheres were governed by a negative dielectrophoretic force in this frequency range. The gold coated polystyrene microspheres were exploited to form the rnicrowire automatically according to their stable dielectrophoretic and electric characterisations.展开更多
基金funding support from National Natural Science Foundation of China(Grant No.52179109)Jiangsu Provincial Natural Science Foundation(Grant No.BK20230967)Open Research Fund of State Key Laboratory of Mechanical Behavior and System Safety of Traffic Engineering Structures,Shijiazhuang Tiedao University(Grant No.KF2022-02).
文摘Existing studies have focused on the behavior of the retaining wall equipped with expanded polystyrene(EPS)geofoam inclusions under semi-infinite surcharge loading rather than limited surcharge loading.In this paper,the failure mode and the earth pressure acting on the rigid retaining wall with EPS geofoam inclusions and granular backfills(henceforth referred to as EPS-wall),under limited surcharge loading are investigated through two-and three-dimensional model tests.The testing results show that different from the sliding of almost all the backfill in the EPS-wall under semi-infinite surcharge loading,only an approximately triangular backfill slides in the wall under limited surcharge loading.The distribution of the lateral earth pressure on the EPS-wall under limited surcharge loading is non-linear,and the distribution changes from the increase of the wall depth to the decrease with the increase of the limited surcharge loading.An approach based on the force equilibrium of a differential element is developed to predict the lateral earth pressure behind the EPS-wall subjected to limited surcharge loading,and its performance was fully validated by the three-dimensional model tests.
文摘The catalytic conversion of polystyrene (PS) was studied in the presence of the materials type HZSM-5, CeO<sub>2</sub>, 10% CeO<sub>2</sub>/HZSM-5 and 20% CeO<sub>2</sub>/HZSM-5, which were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD) and nitrogen adsorption at 77K. The catalytic tests were performed via thermogravimetric analysis (TG) at heating rates of 5, 10 and 20˚C min<sup>−1</sup> in a temperature range from 30˚C to 900˚C. For the tests, a ratio of 30% by mass of each catalytic material mixed with PS was used and the activation energy of the degradation process was determined by the Vyazovkin method. The obtained results showed that the addition of the catalyst to the PS in general reduced its degradation temperature. The 10% CeO<sub>2</sub>/HZSM-5 catalyst showed greater efficiency, as it resulted in lower activation energy for PS degradation. Thus, the combination of CeO<sub>2</sub> with HZSM-5 resulted in materials with potential for application in the catalytic degradation of polystyrene and the results indicate that the production of a composite material can be a good strategy to generate an increase in catalytic activity and a decrease in energy process activation.
文摘Managing agricultural waste and expanded polystyrene (EPS) poses significant environmental and economic challenges. This study aims to create composites from millet husks, rice husks, and recycled EPS, using a manufacturing method that involves dissolving the polystyrene in a solvent followed by cold pressing. Various particle sizes and two binder dosages were investigated to assess their influence on the physico-mechanical properties of the composites. The mechanical properties obtained range from 2.54 to 4.47 MPa for the Modulus of Rupture (MOR) and from 686 to 1400 MPa for the Modulus of Elasticity in Bending (MOE). The results indicate that these composites have potential for applications in the construction sector, particularly for wood structures and interior decoration. Moreover, surface treatments could enhance their durability and mechanical properties. This research contributes to the valorization of agricultural and plastic waste as eco-friendly and economical construction materials.
文摘Electrospinning is a simple technique used to fabricate polymeric nano-fibrous membranes.These nano-fibers have found a wide range of valuable applications in the biomedical field.However,it has not been utilized with solid high explosives yet.Herein,the electrospinning technique has been used to fabricate polystyrene(PS)/1,3,5-trinitro-1,3,5-triazinane(RDX)composite nanofibers.The governed electrospinning parameters,voltage,distance from the collector,flow rate,mandrel rotating speed,time,and solution concentration,that greatly affect the morphology of the obtained nanofibers were optimized.The fabricated PS/RDX nano-fibers were characterized using scanning electron microscopy(SEM),X-ray diffractometer(XRD),and Fourier Transform Infrared(FTIR)spectroscopy.The impact and friction sensitivities of PS/RDX were also measured.The thermal behavior of the prepared composite and the pure materials were studied by the thermal gravimetric analysis technique(TGA).SEM results proved the fabrication of PS/RDX fibers in the nano-size via electrospinning.FTIR spectroscopy confirmed the existence of the characteristic functional groups of both PS and RDX in the composite nano-fibers.XRD sharp peaks showed the conversion of amorphous PS into crystalline shape via electrospinning and also confirmed the formation of PS/RDX composite.The PS fibers absorbed the heat and increased the onset decomposition of the pure RDX from 181.5 to 200.7℃in the case of PS/RDX fibers.Interestingly,PS/RDX nano-fibers showed the relatively low impact and friction sensitivities of 100 J and 360 N respectively.These results could introduce PS/RDX nanofibrous composite in the field of explosives detection with high levels of safety.
基金Fujian External Cooperation project of Natural Science Foundation,China(No.2022I0042)。
文摘Thermo-responsive random copolymers,poly(2-(2-methoxyethoxy)ethoxyethyl methacrylate-co-(ethylene glycol)methyl ether methacrylate)(P(EO_(2)-co-EO_(4/5)))and poly(2-(2-methoxyethoxy)ethoxyethyl methacrylate-co-ethylene glycol methacrylate(P(EO2-co-EG4/5))are synthesized via atom transfer radical polymerization(ATRP).The successful synthesis and the narrow polydispersity index(PDI)of two copolymers are indicated by 1H nuclear magnetic resonance(1H-NMR)and gel permeation chromatography(GPC)analyses.The transition behaviors of polymers in the aqueous solution are demonstrated by changes in turbidity and particle sizes.The transition behavior of P(EO2-co-EG4/5)is found to be milder than that of P(EO2-co-EO4/5).Moreover,the presence of hydrogen bonds without thermo-responsive properties established by hydroxyl groups in the end-side chain of P(EO_(2)-co-EG_(4/5))hinders the dehydration at the transition temperature(TT).Attenuated total reflection Fourier transform infrared spectrometry(ATR-FTIR)analysis along with contact angle measurements reveals that both P(EO_(2)-co-EO_(4/5))and P(EO_(2)-co-EG_(4/5))films undergo phase transitions from hydrophilicity to hydrophobicity above TT.By examining the swelling and collapse behaviors of the polymer films during phase transitions,it can be concluded that the end hydroxyl groups may establish hydrogen bonds with neighboring ether groups within the films,which remain intact throughout the phase transition process due to their strong bonding interactions.This leads to an increase in steric hindrance within swollen films thereby impeding dehydration processes and inducing hysteresis during phase transitions.
文摘BACKGROUND Sodium polystyrene sulfonate(SPS)is commonly prescribed for the management of hyperkalemia,a critical electrolyte imbalance contributing to over 800000 annual visits to emergency departments.AIM To conduct a systematic review of documented cases of SPS-induced colitis and assess its associated prognosis.METHODS Following the PRISMA-P guidelines,our study employed Medical Subject Headings and Health Sciences Descriptors,skillfully combined using Boolean operators,to conduct comprehensive searches across various electronic databases,including Scopus,Web of Science,MEDLINE(PubMed),BIREME(Biblioteca Regional de Medicina),LILACS(Latin American and Caribbean Health Sciences Literature),SciELO(Scientific Electronic Library Online),Embase,and Opengray.eu.Language criteria were confined to English,Spanish,and Portuguese,with no limitations on the publication date.Additionally,we manually scrutinized the reference lists of retrieved studies.To present our findings,we utilized simple descriptive analysis.RESULTS Our search strategy yielded a total of 442 references.After rigorous evaluation,we included 51 references,encompassing 59 documented cases of colitis.Predominant clinical presentations included abdominal pain,observed in 35(60.3%)cases,and bloating,reported in 18(31%)cases.The most frequently affected sites of inflammation were the cecum,rectum,and small intestine,accounting for 31%,25.8%,and 22.4%of cases,respectively.Colonoscopy findings were described in 28(48.2%)cases,and 29(50%)of patients required surgical intervention.Among the subset of patients for whom outcome data was available,39(67.2%)experienced favorable outcomes,while 12(20.6%)unfortunately succumbed to the condition.The mean time required for resolution was 36.7 d,with a range spanning from 1 to 120 d.CONCLUSION SPS demonstrates the capacity to effectively lower serum potassium levels within 24 h.However,this benefit is not without the risk of bowel injury.Our study highlights the absence of high-quality data pertaining to the incidence of adverse events associated with SPS usage,making it challenging to determine whether the potential risks outweigh the benefits.However,a significant mortality rate related to SPS-induced colitis was noted.Future investigations should prioritize randomized controlled trials with a sufficiently large patient cohort to ascertain the true utility and safety profile of this medication.
文摘Chloromethylation of polystyrene (PS) with two different chloromethylating systems methylal/thionyl chloride and paraformaldehyde/trimethylchlorosilane was studied. Soluble chloromethylated polystyrene with a degree of substitution of 89% was obtained. The Conant-Finkelstein reaction on the chloromethylated PS afforded soluble iodomethylated polystyrene with a degree of substitution as high as 96%. The reaction conditions of Minisci were employed to radically pyridinate PS via its iodomethylated derivative. Polyelectrolytes were formed which could be converted to normal polymers by treatment with a 20% aqueous solution of NaOH.
基金Funded by the Specialized Research Fund for the Doctoral Program of Higher Education of China (No. 20050487017)
文摘Atmospheric exposure tests including two experimental stages of high temperature-spraying water cycle and heating-refrigeration cycle were carried out on three currently used ETIS of expanded polystyrene(EPS) board,polystyrene granule mortar and polyurethane foam in order to study the weatherablility of external thermal insulation system(ETIS).The change rules of adhesive strength were hereby studied at different time period of atmospheric exposure tests.The experimental results show that the adhesive strength of three kinds of ETIS changes a little during high temperature-spraying water cycle,but the adhesive strength of ETIS with EPS board decreases significantly after heating-refrigeration cycle.The lowering rate of adhesive strength with painting finishes is obviously faster than that of tile finishes for ETIS of EPS board during heating-refrigeration cycle.The weatherability of ETIS with EPS board is worse than the other two,and ETIS of polystyrene granule mortar and polyurethane foam are more suitable than ETIS of EPS board in cold area.
基金Supported by National Natural Science Foundation of China(Nos.20674023 and 20801022)
文摘Fluorescent polystyrene(PS)/porphyrin(TPPA) composite nanospheres were successfully fabricated by electrospinning. The SEM images clearly show that owing to adding TPPA in PS, the averaged diameter of the composite nanospheres became smaller, from 1500 to 580 nm. Fourier-transform infrared(FTIR) spectra determined the chemical composition of the resulting PS/TPPA composite nanospheres. The photoluminescent(PL) spectral analysis indicates that the peak position of the composite nanospheres in either solid state or water is identical to that of pure TPPA, at about 652 nm, and is still unchangeable when they are left for at least 20 d, indicating the stable photoluminescent property of the fluorescent composite nanospheres.
基金Funded by the National Natural Science Foundation of China(No.21007062)SKLECE Open Fund(No.KF2009-21)
文摘In this paper, magnetic nanospheres coated with polystyrene (Fe3O4@PS) were prepared for the removal of organochlorine pesticides from aqueous solutions. The obtained Fe3O4@PS was round shape with diameter of 55±11 nm. The VSM results illustrated that its higher saturated magnetization was 36.76 emu g^-1 and it could be easily separated from aqueous solutions with a permanent magnet. The adsorption results showed that pesticides could be effectively adsorbed and the adsorption equilibrium time was less than 20 mins. The pseudo-second-order model was suitable to describe the adsorption kinetics. Compared with the Freundlich adsorption model, the adsorption data fitted well with Langmuir model. The effect of salinity and humic acid was also studied and the results illustrated that they could be neglected under optimized conditions. The asobtained sorbent showed a good performance with more than 93.3% pesticides removal in treating actual water samples.
文摘An experimental system for measuring the VLE of polymer solutions based on the staticvapor-pressure method has been established,VLE data for mixtures of toluene and polystyrene withdifferent molecular weight covering a wide range from 2.98×10~3 to 3.84×10~6 were obtained at 35℃.The reduced pressure p/p°versus weight fraction W plot is found to be independent on the molecularweight of the polymer within the experimental error.Calculated activity coefficients are also independenton the molecular weight.However,for the Flory-Huggins interaction parameter x,not only a strongconcentration dependence is observed,but also the molecular weight of the polymer exerts definiteinfluence.Generally,the parameter x slightly increases as the molecular weight of the polymer decreasesespecially when the molecular weight is low.The dependence of the parameter x on the molecularweight can be neglected when the molecular weight of polymer is greater than 1.00×10~4.
基金supported by the National Natural Science Foundation of China (Grant Nos. 50873085 and 21375116)a project funded by the Priority Academic Program Development of Jiangsu Higher Education Institutions (PAPD)
文摘The highly ordered silver-coated colloidal crystals arrays and macroporous silver films were derived through an electrostatics-induced adsorption effect using polystyrene(PS) as templates. Carboxyl-modified PS microspheres were prepared by emulsifier-free emulsion polymerization using methacrylic acid(MAA) as the functional monomer. PS microspheres were self-assembled into close packing colloidal crystals of facecentered cubic arrays to the substrate with vertical deposition method. These colloidal crystals were modified using dopamine(DA) to form poly-dopamine(PDA) during its oxidative polymerization. Through electrostatic interaction, the silver nanoparticles were deposited and adsorbed onto the surfaces of colloidal crystals templates by exposing [Ag(NH_3)_2]^+solution to infrared irradiation. Removal of the polymeric template by etching with methylbenzene solvent resulted in 3D ordered macroporous silver films. The structural and properties of the ordered silver-coated arrays and macroporous silver films were characterized by field emission scanning electron microscopy(FE-SEM), X-ray diffraction(XRD), UV-vis spectroscopy and surface-enhanced Raman spectroscopy(SERS). The results indicate that the prepared silver-coated arrays and macroporous silver films possess the features of ordered multilayer arrangement, uniformity and repeatability as well as an ideal SERS effect.
基金Supported by the National Natural Science Foundation of China(Nos.20473029and20573041)Program for Changjiang Scholars and Innovative Research Team in the University of China(No.IRT0422)+3 种基金Program for New Century Excellent Talents in theUniversity of ChinaScientific Research Foundation for the Returned Overseas Chinese Scholars Initiated State Education Ministry of Chinathe 111 Project of China(No.B06009).
文摘A facile and novel method for the production of a large area of well-ordered polystyrene (PS) colloidal crystal monolayer was established using the surfactant-free Langmuir-Blodgett (LB) technique. The hydrophobic property (film-forming ability) of PS spheres was improved by a thermo-rheology treatment before LB assembly, and a large film was obtained. In contrast to the traditional LB technique, no surfactant was needed in this method, which could eliminate the additional contamination of surfactants in the preparation process and provided the products with versa- tile applications in nanosphere lithography (NSL) for biosensor, surface plasmon resonance, and surface enhanced Raman spectroscopy .
基金National Natural Science Foundation of China(No.51475315)Innovative Project on the Integration of Industry,Education and Research of Jiangsu Province,China(No.BY2014059-10)
文摘In the present work,a study is made to investigate the effects of process parameters,namely,laser power,scanning speed,hatch spacing, layer thickness and powder temperature, on the tensile strength for selective laser sintering( SLS) of polystyrene( PS). Artificial neural network( ANN) methodology is employed to develop mathematical relationships between the process parameters and the output variable of the sintering strength. Experimental data are used to train and test the network. The present neural network model is applied to predicting the experimental outcome as a function of input parameters within a specified range. Predicted sintering strength using the trained back propagation( BP) network model showed quite a good agreement with measured ones. The results showed that the networks had high processing speed,the abilities of error-correcting and self-organizing. ANN models had favorable performance and proved to be an applicable tool for predicting sintering strength SLS of PS.
文摘Sulfonated syndiotactic polystyrene ionomers (SsPS) with 1.8 mol% degree of sulfonation have been studied. WAXD shows that the crystallinity of SsPS ionomers was decreased with increasing diameter size of the counter ions and sPS > SsPS-H > SsPS-K > SsPS-Zn. Moreover, SsPS ionomers only have alpha crystal form, while original sPS has two crystal forms: alpha and beta crystal form. TGA shows that the thermal stability of SsPS ionomers is higher than that of the original sPS and SsPS-Zn > SsPS-K > SsPS-H. DSC shows that all the glass transition temperatures (T-g) of SsPS ionomers are higher than that of the neat sPS and SsPS-Zn > SsPS-Na > SsPS-K > SsPS-H. However, the melting temperature (T-m) and crystallization peak temperature (T-p) of SsPS ionomers are lower and SsPS-H > SsPS-Zn > SsPS-K > SsPS-Na, while the crystallinity (X-c) of SsPS-Zn is the lowest. Nonisothermal crystallization kinetics shows that the Avrami index of sPS and SsPS-H are both about 4, suggesting the nucleation growth of SsPS-H with lower degree of sulfonation still keeps its three-dimension form. FTIR spectra of SsPS ionomers show a splitting absorption band for asymmetric stretching vibration of sulfonation group. The CH in-plane bending vibration of benzene ring shifted to higher wavenumber and the symmetric stretching vibration of sulfonation group changed slightly with different counter ion neutralized SsPS ionomers.
文摘Broadband Mie scattering is used to determine the parameters of polystyrene aerosol beads in air,such as size and wavelength dependence of refractive index.This method consists in the selection of such parameters of the scattering object,which reproduce observed spectrum properties.That is why it is very sensitive and hence very precise.We found that there is an ambiguity of polystyrene aerosol beads properties,determined with this method.Different combinations of polystyrene particle size and its refractive index can give the same position of Mie resonances.This ambiguity leads to an increase in the error in determining the size and refractive index of the particle.The refined errors are calculated and the way of their reduction is indicated.
基金Project supported by the National Natural Science Foundation of China (Grant No 10334060) and The State Key Development Program for Basic Research of China (Grant No 2005CB623602).
文摘Arrays of noble metal nanoparticles show potential applications in (bio-)sensing, optical storage, surface-enhanced spectroscopy, and waveguides. For all such potential devices, controlling the size, morphology, and interparticle spacing of the nanoparticles is very important. Here, we combine seed-mediated growth with nanosphere lithography to study the controllable growth of gold nanoparticles (Au NPs), in which the self-assembly monolayer of polystyrene (PS) on a silicon surface is used to guide the modification of allaunesilanes and the subsequent adsorption of gold seeds; seed-mediated growth is applied to controlling the morphology and size of Au NPs. The size of adsorption region (determining the number of adsorbed gold seeds) is controlled by etching PS microspheres with oxygen plasma or annealing PS microspheres at the glass transition temperature. The size and morphology of the Au NPs are controlled by changing growth conditions. In such a way, we have achieved the dual control of the obtained Au NPs. Preliminary results show that this strategy holds a great promise. This approach can also be extended to a wide range of materials and substrates.
文摘The polystyrene/rectorite nanocomposites were prepared by free radical polymerization of styrene containing dispersed organophilic rectorite. The structures and thermal properties of these hybrids have been investigated by X\|ray diffraction (XRD), fourier transform infrared (FT\|IR), positron annihilation spectroscopy (PAS) and thermal gravimetric analysis (TGA) techniques. It was found that exfoliation of rectorite in polystyrene (PS) matrix was achieved. The average free\|volume radius in the PS/clay nanocomposites is generally same as that in PS. Along with increment of rectorite contents, the interface between rectorite and polystyrene matrix increases, and the free\|volume concentration decreases obviously. And the polystyrene nanocomposites have higher thermal decomposition temperature than pure PS.
基金Project supported by the National Natural Science Foundation of China (Grant No. 51075087)the State Key Laboratory of Fluid Power Transmission and Control,ZheJiang University of China (Grnat No. GZKF-201004)the China Scholarship Council(Grant No. 2009612129)
文摘Microspheres coated with a perfectly conductive surface have many advantages in the applications of biosensors and micro-electromechanical systems. Polystyrene microspheres with the diameter of 10 μm were coated with a 50 nmthick gold layer using an electroless gold plating approach. Dielectrophoresis (DEP) for bare microspheres and shelled microspheres was theoretically analysed and the real part of the Clausius Mossotti factor was calculated for the two kinds of microspheres. The experiments on the dielectrophoretic characterisation of the uncoated polystyrene microspheres and gold coated polystyrene microspheres (GCPMs) were carried out. Experimental results showed that the gold coated polystyrene microspheres were only acted by a positive dielectrophoretic force when the frequency was below 40M Hz, while the uncoated polystyrene microspheres were governed by a negative dielectrophoretic force in this frequency range. The gold coated polystyrene microspheres were exploited to form the rnicrowire automatically according to their stable dielectrophoretic and electric characterisations.