GHz burst-mode femtosecond(fs)laser,which emits a series of pulse trains with extremely short intervals of several hundred picoseconds,provides distinct characteristics in materials processing as compared with the con...GHz burst-mode femtosecond(fs)laser,which emits a series of pulse trains with extremely short intervals of several hundred picoseconds,provides distinct characteristics in materials processing as compared with the conventional irradiation scheme of fs laser(single-pulse mode).In this paper,we take advantage of the moderate pulse interval of 205 ps(4.88 GHz)in the burst pulse for high-quality and high-efficiency micromachining of single crystalline sapphire by laser induced plasma assisted ablation(LIPAA).Specifically,the preceding pulses in the burst generate plasma by ablation of copper placed behind the sapphire substrate,which interacts with the subsequent pulses to induce ablation at the rear surface of sapphire substrates.As a result,not only the ablation quality but also the ablation efficiency and the fabrication resolution are greatly improved compared to the other schemes including single-pulse mode fs laser direct ablation,single-pulse mode fs-LIPAA,and nanosecond-LIPAA.展开更多
An experiment of a 500-fs KrF laser pulse incident upon a high density supersonic O2 gas jet synchronously with an ns frequency-doubled Nd:YAG laser pulse is performed in orthogonal configuration. Significant atomic ...An experiment of a 500-fs KrF laser pulse incident upon a high density supersonic O2 gas jet synchronously with an ns frequency-doubled Nd:YAG laser pulse is performed in orthogonal configuration. Significant atomic emission enhancement of over forty-fold is observed with an optical multi-channel analyser. The enhancement effect is probably attributed to the different ionization mechanisms between fs and ns laser pulses.展开更多
We report spectroscopic studies on plasma electron number density of laser-induced plasma produced by ns-Nd:YAG laser light pulses on an aluminum sample in air at atmospheric pressure. The effect of different laser e...We report spectroscopic studies on plasma electron number density of laser-induced plasma produced by ns-Nd:YAG laser light pulses on an aluminum sample in air at atmospheric pressure. The effect of different laser energy and the effect of different laser wavelengths were compared. The experimentally observed line profiles of neutral aluminum have been used to extract the excitation temperature using the Boltzmann plot method, whereas the electron number density has been determined from the Stark broadened as well as using the Saha-Boltzmann equation (SBE). Each approach was also carried out by using the AI emission line and Mg emission lines. It was observed that the,SBE method generated a little higher electron number density value than the Stark broadening, method, but within the experimental uncertainty range. Comparisons of Ne determined by the two methods show the presence of a linear relation which is independent of laser energy or laser wavelength. These results show the applicability of the SBE method for Are determination, especially when the system does not have any pure emission lines whose electron impact factor is known, Also use of Mg lines gives superior results than Al lines.展开更多
An experimental setup of laser-induced graphite plasma was built and the spectral characteristics and properties of graphite plasma were studied. From the temporal behavior of graphite plasma, the duration of CN parti...An experimental setup of laser-induced graphite plasma was built and the spectral characteristics and properties of graphite plasma were studied. From the temporal behavior of graphite plasma, the duration of CN partials (B2 ∑+ →-X2 ∑+) emission was two times longer than that of atomic carbon, and all intensities reached the maximum during the early stage from 0.2 μs to 0.8 μs. The electron temperature decreased from 11807 K to 8755 K, the vibration temperature decreased from 8973 K to 6472 K, and the rotational temperature decreased from 7288 K to 4491 K with the delay time, respectively. The effect of the laser energy was also studied, and it was found that the thresholds and spectral characteristics of CN molecular and C atomic spectroscopy presented great differences. At lower laser energies, the electron excited temperature, the electron density, the vibrational temperature and rotational temperature of CN partials increased rapidly. At higher laser energies, the increasing of electron excited temperature and electron density slow down, and the vibrational temperature and rotational temperature even trend to saturation due to plasma shielding and dissociation of CN molecules. The relationship among the three kinds of temperatures was Telec〉Tvib〉Trot at the same time. The electron density of the graphite plasma was in the order of 1017 cm-3 and 1018 cm-3.展开更多
Chemical effects in different aqueous solutions induced by plasma with glow discharge electrolysis (GDE) and contact glow discharge electrolysis (CGDE) are described in this paper. The experimental and discharge char...Chemical effects in different aqueous solutions induced by plasma with glow discharge electrolysis (GDE) and contact glow discharge electrolysis (CGDE) are described in this paper. The experimental and discharge characteristics are also reviewed. These are followed by a discussion of their mechanisms of both anodic and cathodic CGDE..展开更多
A novel fibre-coupling zig-zag beam deflection technology is developed to investigate the attenuation process of laser-induced shock waves in air. Utilizing ordinal reflections of probe beams by a pair of parallel mir...A novel fibre-coupling zig-zag beam deflection technology is developed to investigate the attenuation process of laser-induced shock waves in air. Utilizing ordinal reflections of probe beams by a pair of parallel mirrors, a zig-zag beam field is formed, which has eleven probe beams in the horizontal plane. When a laser-induced shock wave propagates through the testing field, it causes eleven deflection signals one after another. The whole attenuation process of the shock wave in air can be detected and illuminated clearly on one experimental curve.展开更多
This work reports spectroscopic studies of uranium containing plasma generated in air and argon environments. The 532 nm Q-switched Nd:YAG laser generates the optical breakdown plasma, which was recorded by a spectro...This work reports spectroscopic studies of uranium containing plasma generated in air and argon environments. The 532 nm Q-switched Nd:YAG laser generates the optical breakdown plasma, which was recorded by a spectrometer and an intensified charge coupled device having a resolution of 25 pm. Neutral and ionized uranium lines in the wavelength range of 385.8-391.9 nm indicate significant width and shift variations during the first few microseconds. Electron temperature and density of the plasma are determined using the Boltzmann plot and the Saha-Boltzmann equation at various time delay. The study reveals the power law decay pattern of electron temperature and density, which changes to exponential decay pattern if large gate- width is used to acquire the signal, due to an averaging effect.展开更多
The poloidal rotation of the magnetized edge plasma in tokamak driven by the ponderomotive force which is generated by injecting lower hybrid wave(LHW) electric field has been studied. The LHW is launched from a waveg...The poloidal rotation of the magnetized edge plasma in tokamak driven by the ponderomotive force which is generated by injecting lower hybrid wave(LHW) electric field has been studied. The LHW is launched from a waveguide in the plasma edge, and by Brambilla's grill theory, analytic expressions for the wave electric field in the slab model of an inhomogeneous cold plasma have been derived. It is shown that a strong wave electric field will be generated in the plasma edge by injecting LH wave of the power in MW magnitude, and this electric field will induce a poloidal rotation with a sheared poloidal velocity.展开更多
Optical emission from TiO2 plasma, generated by a nanosecond laser is spectroscopically analysed. The main chemical species are identified and the spatio-temporal distribution of the plasma parameters such as electron...Optical emission from TiO2 plasma, generated by a nanosecond laser is spectroscopically analysed. The main chemical species are identified and the spatio-temporal distribution of the plasma parameters such as electron temperature and density are characterized based on the study of spectral distribution of the line intensities and their broadening characteristics. The parameters of laser induced plasma vary quickly owing to its expansion at low background pressure and the possible deviations from local thermodynamic equilibrium conditions are tested to show its validity.展开更多
In general, atomic emission spectrometry (AES) is an excellent technique for determination of metal elements. However, its capability of determining nonmetals has not been developed well. The major reasons are the res...In general, atomic emission spectrometry (AES) is an excellent technique for determination of metal elements. However, its capability of determining nonmetals has not been developed well. The major reasons are the resonance lines of most nonmetals lie in the vacuum ultraviolet spectral region and the ionic lines of these elements are difficult to be used because the ionization potentials of the elements are very high. And furthermore only He plasma can efficiently excit those ionic resonance lines. The practical application of HeICP-AES to determining the nonmetals is also difficult because its operating and perchace costs are very high. In contrast to HeICPAES, the costs of He microwave induced plasma (MIP)-AES are relatively low, HeMIP has a high excitation capability which can excite ionic lines of various nonmetals and the nonmetals can be determined by HeMIP-AES with a high sensitivity.展开更多
The determination of copper by MIP-AES was investigated in detail. Aqueous samples were introduced from an ultrasonic nebulizer and the solvent was removed by a desolvation device before introduction of the aerosol in...The determination of copper by MIP-AES was investigated in detail. Aqueous samples were introduced from an ultrasonic nebulizer and the solvent was removed by a desolvation device before introduction of the aerosol into the MIP. The desolvation system consisted of a condenser associated with a concentrated H2SO4 absorption cell. Various experimental conditions and interferences from easily ionised elements (EIEs) were also studied and some practical samples were analyzed.展开更多
Based on the fluid theory of plasma, a model is built to study the characteristics of nitrogen discharge at high pressure with induced argon plasma. In the model, species such as electrons, N2+, N4+, Ar+, and two m...Based on the fluid theory of plasma, a model is built to study the characteristics of nitrogen discharge at high pressure with induced argon plasma. In the model, species such as electrons, N2+, N4+, Ar+, and two metastable states (N2 (A3 ∑ u+), N2 (a1 ∑ u)) are taken into account. The model includes the particle continuity equation, the electron energy balance equation, and Poisson抯iequation. The model ’s solved with a finite difference method. The numerical results are obtained and used to investigate the effect of time taken to add nitrogen gas and initially-induced argon plasma pressure. It is found that lower speeds of adding the nitrogen gas and varying the gas pressure can induce higher plasma density, and inversely lower electron temperature. At high-pressure discharge, the electron density increases when the proportion of nitrogen component is below 4070, while the electron density will keep constant as the nitrogen component further increases. It is also shown that with the increase of initially-induced argon plasma pressure, the density of charged particles increases~ and the electron temperature as well as the electric field decreases.展开更多
An innovative in-flight glass melting technology with induced thermal plasmas was developed for the purpose of energy conservation and environmental protection. Two-dimensional modeling was used to simulate the thermo...An innovative in-flight glass melting technology with induced thermal plasmas was developed for the purpose of energy conservation and environmental protection. Two-dimensional modeling was used to simulate the thermofluid fields in the plasma torch. The in-flight melting behavior of glass raw material was investigated by various analysis methods. Results showed that the plasma temperature was up to 10000 K with a maximum velocity over 30 m/s, which made it possible to melt the granulated glass raw material within milliseconds. The carbonates in the raw material decomposed completely and the compounds in the raw material attainted 100% vitrification during the in-flight time from the nozzle exit to substrate. The particle melting process is similar to the unreacted-core shrinking model.展开更多
Using a low power microwave generator and a surfatron discharge cavity, Ti3O5 was synthesized via the hydrogenation of TiO2 in surface wave induced microwave plasma. Besides, the chemical behavior of hydrogen in the p...Using a low power microwave generator and a surfatron discharge cavity, Ti3O5 was synthesized via the hydrogenation of TiO2 in surface wave induced microwave plasma. Besides, the chemical behavior of hydrogen in the plasma and its influence on the formation of Ti3O5 were preliminarily studied.展开更多
We report an optical spectroscopy study on LaSb, a compound recently identified to exhibit extremely large magnetoresistance. Our optieal measurement indicates that the material has a low carrier density. More inter- ...We report an optical spectroscopy study on LaSb, a compound recently identified to exhibit extremely large magnetoresistance. Our optieal measurement indicates that the material has a low carrier density. More inter- estingly, the study reveals that the plasma frequency increases with decreasing temperature. This phenomenon suggests either an increase of the conducting carrier density or/and a decrease of the effective mass of carriers with decreasing temperature. We attribute it primarily to the latter effect. Two possible scenarios on its physical origin are examined and discussed. The study offers new insight into the electronic structure of this compound.展开更多
Keyhole is the most important characteristic for laser deep penetration welding, and its formation indicates the beginning of laser deep penetration welding mode. The keyhole developing process was analyzed and the ke...Keyhole is the most important characteristic for laser deep penetration welding, and its formation indicates the beginning of laser deep penetration welding mode. The keyhole developing process was analyzed and the keyhole formation time was calculated according to welding speed and the length of weld bead formed in the keyhole formation process. The results showed that the keyhole forms in 40 -70 ms at different rate of change of laser power. In laser deep penetration welding process, the variation of light intensity radiated by laser induced plasma can identify the keyhole formation, but it can not be used to estimate the keyhole formation time because of delay effect.展开更多
Atmospheric pressure plasmas are not only powerful sources for excitation but also very good atomizers. In the early developing stage, the inductively coupled plasma (ICP) was investigated as an atomizer for atomic ab...Atmospheric pressure plasmas are not only powerful sources for excitation but also very good atomizers. In the early developing stage, the inductively coupled plasma (ICP) was investigated as an atomizer for atomic absorption spectrometry (AAS). A multiple pass system,a T-shaped plasma cell,and a long-path torch was used to increase the absorption path length. But all these ICP-AAS systems gave low sensitivities for most展开更多
Based on the fluid theory of plasma, a model is built to study the characteristics of nitrogen discharge at high pressure with induced argon plasma. In the model, species such as electrons, N2+, N4+, Ar+, and two meta...Based on the fluid theory of plasma, a model is built to study the characteristics of nitrogen discharge at high pressure with induced argon plasma. In the model, species such as electrons, N2+, N4+, Ar+, and two metastable states (N 2(A3∑u+), N2 (a1 ∑u-)) are taken into account. The model includes the particle continuity equation, the electron energy balance equation, and Poisson抯equation. The model is solved with a finite difference method. The numerical results are obtained and used to investigate the effect of time taken to add nitrogen gas and initially-induced argon plasma pressure. It is found that lower speeds of adding the nitrogen gas and varying the gas pressure can induce higher plasma density, and inversely lower electron temperature. At high-pressure discharge, the electron density increases when the proportion of nitrogen component is below 40%, while the electron density will keep constant as the nitrogen component further increases. It is also shown that with the increase of initially-induced argon plasma pressure, the density of charged particles increases, and the electron temperature as well as the electric field decreases.展开更多
Microwave induced plasma torches find wide applications in material and chemical analysis.Investigation of a coaxial electrode microwave induced plasma(CE–MIP)torch is conducted in this study,making it available for ...Microwave induced plasma torches find wide applications in material and chemical analysis.Investigation of a coaxial electrode microwave induced plasma(CE–MIP)torch is conducted in this study,making it available for glass surface modification and polishing.A dedicated nozzle is designed to inject secondary gases into the main plasma jet.This study details the adaptation of a characterisation process for CE–MIP technology.Microwave spectrum analysis is used to create a polar plot of the microwave energy being emitted from the coaxial electrode,where the microwave energy couples with the gas to generate the plasma jet.Optical emission spectroscopy analysis is also employed to create spatial maps of the photonic intensity distribution within the plasma jet when different additional gases are injected into it.The CE–MIP torch is experimentally tested for surface energy modification on glass where it creates a super-hydrophilic surface.展开更多
.Laser-induced breakdown spectroscopy(LIBS)is a useful tool for determination of elements in solids,liquids,and gases.For nanosecond LIBS(ns-LIBS),the plasma shielding effect limits its reproducibility,repeatability,a....Laser-induced breakdown spectroscopy(LIBS)is a useful tool for determination of elements in solids,liquids,and gases.For nanosecond LIBS(ns-LIBS),the plasma shielding effect limits its reproducibility,repeatability,and signal-to-noise ratios.Although femtosecond laser filament induced breakdown spectroscopy(FIBS)has no plasma shielding effects,the power density clamping inside the filaments limits the measurement sensitivity.We propose and demonstrate plasma-grating-induced breakdown spectroscopy(GIBS).The technique relies on a plasma excitation source-a plasma grating generated by the interference of two noncollinear femtosecond filaments.We demonstrate that GIBS can overcome the limitations of standard techniques such as ns-LIBS and FIBS.Signal intensity enhancement with GIBS is observed to be greater than 3 times that of FIBS.The matrix effect is also significantly reduced with GIBS,by virtue of the high power and electron density of the plasma grating,demonstrating great potential for analyzing samples with complex matrix.展开更多
基金supported by MEXT Quantum Leap Flagship Program(MEXT Q-LEAP)Grant Number JPMXS0118067246.
文摘GHz burst-mode femtosecond(fs)laser,which emits a series of pulse trains with extremely short intervals of several hundred picoseconds,provides distinct characteristics in materials processing as compared with the conventional irradiation scheme of fs laser(single-pulse mode).In this paper,we take advantage of the moderate pulse interval of 205 ps(4.88 GHz)in the burst pulse for high-quality and high-efficiency micromachining of single crystalline sapphire by laser induced plasma assisted ablation(LIPAA).Specifically,the preceding pulses in the burst generate plasma by ablation of copper placed behind the sapphire substrate,which interacts with the subsequent pulses to induce ablation at the rear surface of sapphire substrates.As a result,not only the ablation quality but also the ablation efficiency and the fabrication resolution are greatly improved compared to the other schemes including single-pulse mode fs laser direct ablation,single-pulse mode fs-LIPAA,and nanosecond-LIPAA.
基金Supported by the National Natural Science Foundation of China under Grant No 10474081.
文摘An experiment of a 500-fs KrF laser pulse incident upon a high density supersonic O2 gas jet synchronously with an ns frequency-doubled Nd:YAG laser pulse is performed in orthogonal configuration. Significant atomic emission enhancement of over forty-fold is observed with an optical multi-channel analyser. The enhancement effect is probably attributed to the different ionization mechanisms between fs and ns laser pulses.
文摘We report spectroscopic studies on plasma electron number density of laser-induced plasma produced by ns-Nd:YAG laser light pulses on an aluminum sample in air at atmospheric pressure. The effect of different laser energy and the effect of different laser wavelengths were compared. The experimentally observed line profiles of neutral aluminum have been used to extract the excitation temperature using the Boltzmann plot method, whereas the electron number density has been determined from the Stark broadened as well as using the Saha-Boltzmann equation (SBE). Each approach was also carried out by using the AI emission line and Mg emission lines. It was observed that the,SBE method generated a little higher electron number density value than the Stark broadening, method, but within the experimental uncertainty range. Comparisons of Ne determined by the two methods show the presence of a linear relation which is independent of laser energy or laser wavelength. These results show the applicability of the SBE method for Are determination, especially when the system does not have any pure emission lines whose electron impact factor is known, Also use of Mg lines gives superior results than Al lines.
基金supported by National Natural Science Foundation of China(No.61205149)Scientific Research Foundation for the Returned Overseas Chinese Scholars of State Education Ministry,Science Research Funds of Chongqing Municipal Education Commission(KJ1500436)+2 种基金Scientific and Technological Talents Training Project of Chongqing(CSTC2013kjrc-qnrc40002)Key Project of Foundation and Advanced Technology Research Project of Chongqing(CSTC2015jcyj B0358)Visiting Scholarship of State Key Laboratory of Power Transmission Equipment & System Security and New Technology(2007DA10512714409)
文摘An experimental setup of laser-induced graphite plasma was built and the spectral characteristics and properties of graphite plasma were studied. From the temporal behavior of graphite plasma, the duration of CN partials (B2 ∑+ →-X2 ∑+) emission was two times longer than that of atomic carbon, and all intensities reached the maximum during the early stage from 0.2 μs to 0.8 μs. The electron temperature decreased from 11807 K to 8755 K, the vibration temperature decreased from 8973 K to 6472 K, and the rotational temperature decreased from 7288 K to 4491 K with the delay time, respectively. The effect of the laser energy was also studied, and it was found that the thresholds and spectral characteristics of CN molecular and C atomic spectroscopy presented great differences. At lower laser energies, the electron excited temperature, the electron density, the vibrational temperature and rotational temperature of CN partials increased rapidly. At higher laser energies, the increasing of electron excited temperature and electron density slow down, and the vibrational temperature and rotational temperature even trend to saturation due to plasma shielding and dissociation of CN molecules. The relationship among the three kinds of temperatures was Telec〉Tvib〉Trot at the same time. The electron density of the graphite plasma was in the order of 1017 cm-3 and 1018 cm-3.
文摘Chemical effects in different aqueous solutions induced by plasma with glow discharge electrolysis (GDE) and contact glow discharge electrolysis (CGDE) are described in this paper. The experimental and discharge characteristics are also reviewed. These are followed by a discussion of their mechanisms of both anodic and cathodic CGDE..
基金Supported by the National Natural Science Foundation of China under Grant No 60378003.
文摘A novel fibre-coupling zig-zag beam deflection technology is developed to investigate the attenuation process of laser-induced shock waves in air. Utilizing ordinal reflections of probe beams by a pair of parallel mirrors, a zig-zag beam field is formed, which has eleven probe beams in the horizontal plane. When a laser-induced shock wave propagates through the testing field, it causes eleven deflection signals one after another. The whole attenuation process of the shock wave in air can be detected and illuminated clearly on one experimental curve.
基金supported by the fund obtained from DAE-BARC(ⅫPlan)
文摘This work reports spectroscopic studies of uranium containing plasma generated in air and argon environments. The 532 nm Q-switched Nd:YAG laser generates the optical breakdown plasma, which was recorded by a spectrometer and an intensified charge coupled device having a resolution of 25 pm. Neutral and ionized uranium lines in the wavelength range of 385.8-391.9 nm indicate significant width and shift variations during the first few microseconds. Electron temperature and density of the plasma are determined using the Boltzmann plot and the Saha-Boltzmann equation at various time delay. The study reveals the power law decay pattern of electron temperature and density, which changes to exponential decay pattern if large gate- width is used to acquire the signal, due to an averaging effect.
基金the Nuclear Science Foundation under Grant! No. H7196c0302.
文摘The poloidal rotation of the magnetized edge plasma in tokamak driven by the ponderomotive force which is generated by injecting lower hybrid wave(LHW) electric field has been studied. The LHW is launched from a waveguide in the plasma edge, and by Brambilla's grill theory, analytic expressions for the wave electric field in the slab model of an inhomogeneous cold plasma have been derived. It is shown that a strong wave electric field will be generated in the plasma edge by injecting LH wave of the power in MW magnitude, and this electric field will induce a poloidal rotation with a sheared poloidal velocity.
文摘Optical emission from TiO2 plasma, generated by a nanosecond laser is spectroscopically analysed. The main chemical species are identified and the spatio-temporal distribution of the plasma parameters such as electron temperature and density are characterized based on the study of spectral distribution of the line intensities and their broadening characteristics. The parameters of laser induced plasma vary quickly owing to its expansion at low background pressure and the possible deviations from local thermodynamic equilibrium conditions are tested to show its validity.
文摘In general, atomic emission spectrometry (AES) is an excellent technique for determination of metal elements. However, its capability of determining nonmetals has not been developed well. The major reasons are the resonance lines of most nonmetals lie in the vacuum ultraviolet spectral region and the ionic lines of these elements are difficult to be used because the ionization potentials of the elements are very high. And furthermore only He plasma can efficiently excit those ionic resonance lines. The practical application of HeICP-AES to determining the nonmetals is also difficult because its operating and perchace costs are very high. In contrast to HeICPAES, the costs of He microwave induced plasma (MIP)-AES are relatively low, HeMIP has a high excitation capability which can excite ionic lines of various nonmetals and the nonmetals can be determined by HeMIP-AES with a high sensitivity.
基金Supported by the Natinoal Natural Science Foundation of China.
文摘The determination of copper by MIP-AES was investigated in detail. Aqueous samples were introduced from an ultrasonic nebulizer and the solvent was removed by a desolvation device before introduction of the aerosol into the MIP. The desolvation system consisted of a condenser associated with a concentrated H2SO4 absorption cell. Various experimental conditions and interferences from easily ionised elements (EIEs) were also studied and some practical samples were analyzed.
基金Project supported by the National Science Foundation of China (Grant No. 10675029)the National Basic Research Program of China (Grant Nos. 2008CB717801, 2008CB787103, 2009GB105004, and 2010GB106002)FRFCU (Grant No. DUT12ZD201)
文摘Based on the fluid theory of plasma, a model is built to study the characteristics of nitrogen discharge at high pressure with induced argon plasma. In the model, species such as electrons, N2+, N4+, Ar+, and two metastable states (N2 (A3 ∑ u+), N2 (a1 ∑ u)) are taken into account. The model includes the particle continuity equation, the electron energy balance equation, and Poisson抯iequation. The model ’s solved with a finite difference method. The numerical results are obtained and used to investigate the effect of time taken to add nitrogen gas and initially-induced argon plasma pressure. It is found that lower speeds of adding the nitrogen gas and varying the gas pressure can induce higher plasma density, and inversely lower electron temperature. At high-pressure discharge, the electron density increases when the proportion of nitrogen component is below 4070, while the electron density will keep constant as the nitrogen component further increases. It is also shown that with the increase of initially-induced argon plasma pressure, the density of charged particles increases~ and the electron temperature as well as the electric field decreases.
基金the New Energy and Industrial Technology Development Organization of Japan(No.A0006)
文摘An innovative in-flight glass melting technology with induced thermal plasmas was developed for the purpose of energy conservation and environmental protection. Two-dimensional modeling was used to simulate the thermofluid fields in the plasma torch. The in-flight melting behavior of glass raw material was investigated by various analysis methods. Results showed that the plasma temperature was up to 10000 K with a maximum velocity over 30 m/s, which made it possible to melt the granulated glass raw material within milliseconds. The carbonates in the raw material decomposed completely and the compounds in the raw material attainted 100% vitrification during the in-flight time from the nozzle exit to substrate. The particle melting process is similar to the unreacted-core shrinking model.
文摘Using a low power microwave generator and a surfatron discharge cavity, Ti3O5 was synthesized via the hydrogenation of TiO2 in surface wave induced microwave plasma. Besides, the chemical behavior of hydrogen in the plasma and its influence on the formation of Ti3O5 were preliminarily studied.
基金Supported by the National Natural Science Foundation of China under Grant Nos 11327806 and GZ1123the National Key Research and Development Program of China under Grant No 2016YFA0300902
文摘We report an optical spectroscopy study on LaSb, a compound recently identified to exhibit extremely large magnetoresistance. Our optieal measurement indicates that the material has a low carrier density. More inter- estingly, the study reveals that the plasma frequency increases with decreasing temperature. This phenomenon suggests either an increase of the conducting carrier density or/and a decrease of the effective mass of carriers with decreasing temperature. We attribute it primarily to the latter effect. Two possible scenarios on its physical origin are examined and discussed. The study offers new insight into the electronic structure of this compound.
基金Supported by National Natural Science Foundation of China ( Grant No. 50905099 ) and the Joint Foundation of the National Natural Science Foundation of China and China Academy of Engineering Physics (Grant No. 10776020).
文摘Keyhole is the most important characteristic for laser deep penetration welding, and its formation indicates the beginning of laser deep penetration welding mode. The keyhole developing process was analyzed and the keyhole formation time was calculated according to welding speed and the length of weld bead formed in the keyhole formation process. The results showed that the keyhole forms in 40 -70 ms at different rate of change of laser power. In laser deep penetration welding process, the variation of light intensity radiated by laser induced plasma can identify the keyhole formation, but it can not be used to estimate the keyhole formation time because of delay effect.
文摘Atmospheric pressure plasmas are not only powerful sources for excitation but also very good atomizers. In the early developing stage, the inductively coupled plasma (ICP) was investigated as an atomizer for atomic absorption spectrometry (AAS). A multiple pass system,a T-shaped plasma cell,and a long-path torch was used to increase the absorption path length. But all these ICP-AAS systems gave low sensitivities for most
基金Project supported by the National Science Foundation of China (Grant No. 10675029)the National Basic Research Program of China (Grant Nos. 2008CB717801, 2008CB787103, 2009GB105004, and 2010GB106002)FRFCU (Grant No. DUT12ZD201)
文摘Based on the fluid theory of plasma, a model is built to study the characteristics of nitrogen discharge at high pressure with induced argon plasma. In the model, species such as electrons, N2+, N4+, Ar+, and two metastable states (N 2(A3∑u+), N2 (a1 ∑u-)) are taken into account. The model includes the particle continuity equation, the electron energy balance equation, and Poisson抯equation. The model is solved with a finite difference method. The numerical results are obtained and used to investigate the effect of time taken to add nitrogen gas and initially-induced argon plasma pressure. It is found that lower speeds of adding the nitrogen gas and varying the gas pressure can induce higher plasma density, and inversely lower electron temperature. At high-pressure discharge, the electron density increases when the proportion of nitrogen component is below 40%, while the electron density will keep constant as the nitrogen component further increases. It is also shown that with the increase of initially-induced argon plasma pressure, the density of charged particles increases, and the electron temperature as well as the electric field decreases.
基金funded by the Centre for Innovative Manufacturing in Ultra Precision of the Engineering and Physical Sciences Research Council,UK(Grant No.EP/I033491/1)the Centre for Doctoral Training in Ultra Precision Engineering of the Engineering and Physical Sciences Research Council,UK(Grant No.EP/K503241/1)+2 种基金the Science Foundation Ireland(SFI)(Grant No.15/RP/B3208)Irish Research Council(Grant No.CLNE/2018/1530)the National Natural Science Foundation of China(Grant No.51705462).
文摘Microwave induced plasma torches find wide applications in material and chemical analysis.Investigation of a coaxial electrode microwave induced plasma(CE–MIP)torch is conducted in this study,making it available for glass surface modification and polishing.A dedicated nozzle is designed to inject secondary gases into the main plasma jet.This study details the adaptation of a characterisation process for CE–MIP technology.Microwave spectrum analysis is used to create a polar plot of the microwave energy being emitted from the coaxial electrode,where the microwave energy couples with the gas to generate the plasma jet.Optical emission spectroscopy analysis is also employed to create spatial maps of the photonic intensity distribution within the plasma jet when different additional gases are injected into it.The CE–MIP torch is experimentally tested for surface energy modification on glass where it creates a super-hydrophilic surface.
基金We acknowledge the support fromthe National Key Research and Development Program(No.2018YFB0407100)the National Natural Science Foundation of China(No.11621404)the Key Project of Shanghai Education Commission(No.2017-01-07-00-05-E00021).
文摘.Laser-induced breakdown spectroscopy(LIBS)is a useful tool for determination of elements in solids,liquids,and gases.For nanosecond LIBS(ns-LIBS),the plasma shielding effect limits its reproducibility,repeatability,and signal-to-noise ratios.Although femtosecond laser filament induced breakdown spectroscopy(FIBS)has no plasma shielding effects,the power density clamping inside the filaments limits the measurement sensitivity.We propose and demonstrate plasma-grating-induced breakdown spectroscopy(GIBS).The technique relies on a plasma excitation source-a plasma grating generated by the interference of two noncollinear femtosecond filaments.We demonstrate that GIBS can overcome the limitations of standard techniques such as ns-LIBS and FIBS.Signal intensity enhancement with GIBS is observed to be greater than 3 times that of FIBS.The matrix effect is also significantly reduced with GIBS,by virtue of the high power and electron density of the plasma grating,demonstrating great potential for analyzing samples with complex matrix.