Assessing efficacy of standard impregnation techniques on die-cast aluminum alloys using X-ray micro-CT

Utilizing lightweight Al alloys in various industrial applications requires achieving precise pressure tightness and leak requirements.Vacuum pressure impregnation(VPI)with thermosetting polymers is commonly used to address leakage defects in die-cast Al alloys.In this study,the efficacy of the VPI technique in sealing alloy parts was investigated using a combination of nondestructive micro X-ray computed tomography(micro XCT)and a standard leak test.The results demonstrate that the commonly used water leak test is insufficient for determining the sealing performance.Instead,micro XCT shows distinct advantages by enabling more comprehensive analysis.It reveals the presence of a low atomic number impregnates sealant within casting defects,which has low grey contrast and allows for visualizing primary leakage paths in 3D.The effective atomic number of impregnated resin is 6.75 and that of Al alloy is 13.69 by dual-energy X-ray CT.This research findings will contribute to enhancing the standard VPI process parameters and the properties of impregnating sealants to improve quality assurance for impregnation in industrial metals.

Preparation of activated carbon from sunflower straw through H_(3)PO_(4) activation and its application for acid fuchsin dye adsorption

With the development circular economy, the use of agricultural waste to prepare biomass materials to remove pollutants has become a research hotspot. In this study, sunflower straw activated carbon (SSAC) was prepared by the one-step activation method, with sunflower straw (SS) used as the raw material and H3PO4 used as the activator. Four types of SSAC were prepared with impregnation ratios (weight of SS to weight of H3PO4) of 1:1, 1:2, 1:3, and 1:5, corresponding to SSAC1, SSAC2, SSAC3, and SSAC4, respectively. The adsorption process of acid fuchsin (AF) in water using the four types of SSAC was studied. The results showed that the impregnation ratio significantly affected the structure of the materials. The increase in the impregnation ratio increased the specific surface area and pore volume of SSAC and improved the adsorption capacity of AF. However, an impregnation ratio that was too large led to a decrease in specific surface area. SSAC3, with an impregnation ratio of 1:3, had the largest specific surface area (1 794.01 m2/g), and SSAC4, with an impregnation ratio of 1:5, exhibited the smallest microporosity (0.052 7 cm3/g) and the largest pore volume (2.549 cm3/g). The adsorption kinetics of AF using the four types of SSAC agreed with the quasi-second-order adsorption kinetic model. The Langmuir isotherm model was suitable to describe SSAC3 and SSAC4, and the Freundlich isotherm model was appropriate to describe SSAC1 and SSAC2. The result of thermodynamics showed that the adsorption process was spontaneous and endothermic. At 303 K, SSAC4 showed a removal rate of 97.73% for 200-mg/L AF with a maximum adsorption capacity of 2 763.36 mg/g, the highest among the four types of SSAC. This study showed that SAAC prepared by the H3PO4-based one-step activation method is a green and efficient carbon material and has significant application potential for the treatment of dye-containing wastewater.

Selecting the Technology of Sodium Silicate Modified Poplar with the Highest Performance by Fuzzy Orthogonal Method

Sodium silicate modification can improve the overall performance of wood.The modification process has a great influence on the properties of modified wood.In this study,a new method was introduced to analyze the wood modification process,and the properties of modified wood were studied.Poplar wood was modified with sodium silicate by vacuum-pressure impregnation.After screening using single-factor experiments,an orthogonal experiment was carried out with solution concentration,impregnation time,impregnation pressure,and the cycle times as experimental factors.The modified poplar with the best properties was selected by fuzzy mathematics and characterized by SEM,FT-IR,XRD and TG.The results showed that some lignin and hemicellulose were removed from the wood due to the alkaline action of sodium silicate,and the orderly crystal area of poplar became disorderly,resulting in the reduction of crystallinity of the modified poplar wood.FT-IR analysis showed that sodium silicate was hydrolyzed to form polysilicic acid in wood,and structural analysis revealed the formation of Si-O-Si and Si-O-C,indicating that sodium silicate reacted with fibers on the wood cell wall.TG-DTG curves showed that the final residual mass of modified poplar wood increased from 25%to 67%,and the temperature of the maximum loss rate decreased from 343℃ to 276℃.The heat release and smoke release of modified poplar wood decreased obviously.This kind of material with high strength and fire resistance can be used in the outdoor building and indoor furniture.

Research on Fe-based impregnated diamond drill bits strengthened by Nano-NbC and Nano-WC

In order to improve the matrix performance of impregnated diamond drill bit to better meet the drilling needs,the effects of the addition of nano-WC and nano-NbC particles on the matrix material together with the mechanical properties and microstructure of the diamond-matrix composite material of the Fe-based diamond drill bit were studied by using the method of uniform formula design,regression analysis and solution finding.An indoor drilling test was also carried out using the fabricated impregnated diamond drill bit.The results showed that after the addition of nano-NbC and nano-WC,the hardness and flexural strength of the matrix material got improved,as the flexural strength of the diamond composite material increased to 4.29%,the wear-resistance ratio increased to 8.75%,and the tighter the chemical bonding between the diamond and the matrix.This,indicates that the addition of nanoparticles has a positive significance in improving the performance of the diamond composite.The results of the drilling test showed that the mechanical drilling speed of the impregnated diamond drill bit after nanoparticle strengthening is 25.85%higher than that of the conventional drill bit,and the matrix wear was increased by 17.5%.It proves that nanoparticles can improve the drilling performance and efficiency of drill bit.

Mechanism, behaviour and application of iron nitrate modified carbon nanotube composites for the adsorption of arsenic in aqueous solutions

In this study,ferric nitrate modified carbon nanotube composites (FCNT) were prepared by isovolumetric impregnation using carbon nanotubes (CNTs) as the carrier and ferric nitrates the active agent.The batch experiments showed that FCNT could effectively oxidize As(III) to As(V) and react with it to form stable iron arsenate precipitates.When the dosage of FCNT was 0.1 g·L^(–1),pH value was 5–6,reaction temperature was 35℃ and reaction time was 2 h,the best arsenic removal effect could be achieved,and the removal rate of As(V) could reach 99.1%,which was always higher than 90%under acidic conditions.The adsorption results of FCNT were found to be consistent with Langmuir adsorption by static adsorption isotherm fitting,and the maximum adsorption capacity reached 118.3 mg·g^(-1).The material phase and property analysis by scanning electron microscopy,Brunauer–Emmett–Teller,Fourier transform infrared spectoscopy,X-ray photoelectron spectroscopy and other characterization methods,as well as adsorption isotherm modeling,were used to explore the adsorption mechanism of FCNT on arsenic.It was found that FCNT has microporous structure and nanostructure,and iron nanoparticles are loosely distributed on CNTs,which makes the material have good oxidation,adsorption and magnetic separation properties.Arsenic migrates on the surface of FCNT composites is mainly removed by forming insoluble compounds and co-precipitation.All the results show that FCNT treats arsenic at low cost with high adsorption efficiency,and the results also provide the experimental data basis and theoretical basis for arsenic contamination in groundwater.

Facile synthesis of hydrochar-supported catalysts from glucose and its catalytic activity towards the production of functional amines

Since the utilization of abundant biomass to develop advanced materials has become an utmost priority in recent years,we developed two sustainable routes(i.e.,the impregnation method and the one-pot synthesis)to prepare the hydrochar-supported catalysts and tested its catalytic performance on the reductive amination.Several techniques,such as TEM,XRD and XPS,were adopted to characterize the structural and catalytic features of samples.Results indicated that the impregnation method favors the formation of outer-sphere surface complexes with porous structure as well as well-distributed metallic nanoparticles,while the one-pot synthesis tends to form the inner-sphere surface complexes with relatively smooth appearance and amorphous metals.This difference explains the better activity of catalysts prepared by the impregnation method which can selectively convert benzaldehyde to benzylamine with an excellent yield of 93.7%under the optimal reaction conditions;in contrast,the catalyst prepared by the one-pot synthesis only exhibits a low selectivity near to zero.Furthermore,the gram-scale test catalyzed by the same catalysts exhibits a similar yield of benzylamine in comparison to its smaller scale,which is comparable to the previously reported heterogeneous noble-based catalysts.More surprisingly,the prepared catalysts can be expediently recycled by a magnetic bar and remain the satisfying catalytic activity after reusing up to five times.In conclusion,these developed catalysts enable the synthesis of functional amines with excellent selectivity and carbon balance,proving cost-effective and sustainable access to the wide application of reductive amination.

Preparation and Characterization of Stellera Chamaejasme-Based Carbon Molecular Sieves

The activation effect of boric acid as an activator is good,and we investigate the best activation conditions for the boric acid impregnation method.To represent the structural characteristics and adsorption performance of the Stellera Chamaejasme based carbon molecular sieves,we use Brunner-Emmet-Teller(BET)measurements,scan-ning electron microscope(SEM),Raman spectra(Raman),X-ray diffraction(XRD),and adsorption property measurement.When the loading ratio was 0.68:1,the specific surface area was 532.21 m^(2)/g,the total pore volume was 0.24 cm 3/g,the average pore size was 1.81 nm,the adsorption value of methylene blue was 145.28 mg/g,and the adsorption value of iodine was 713.33 mg/g,the results showed that boric acid had better activation effect.The carbon molecular sieves made from Stellera Chamaejasme and activated with boric acid produce two peaks on the aperture distribution graph that are densely distributed in the micropore range.This indicates that boric acid’s pore-forming tendency is primarily micropore.

Scale and Associated Factors of Using Pyrethroid-Impregnated Mosquito Nets as Fishing Tools on Nokoué Lake within Sô-Ava Municipality in Benin, 2020

Background: In lacustrine communities, whether in Benin or elsewhere, populations use impregnated mosquito nets (IMNs) as fishing nets. This depletes the lake of its fishery resources, which in turn are contaminated by the pyrethroids impregnated in the nets. This study aims to determine the scale and factors associated with the use of pyrethroid-impregnated mosquito nets as fishing tools in the municipality of Sô-Ava in Benin. Methods: This is a cross-sectional and analytical study with two components. First, a quantitative component was made up of 280 volunteers who were interviewed in the seven districts of the city. Data collection was done in two phases: the first from September to October 2020, and the second in August 2022. Data were analyzed with Stata and logistic regression was used. Another qualitative component was made up of forty participants chosen by reasoned choice, of which 32 were split into four focus groups of eight members each, and the rest participated in semi-structured interviews. Triangulation of the different sources was used to analyze the data. Results: Around 67% of the population reported using impregnated mosquito nets as fishing tools and 33% exclusively for malaria. Seasonal fishermen (ORa = 2.03, CI = 1.35 - 4.97, P = 0.004) and years of professional experience (ORa = 1.53, CI = 1.00 - 2.05, P = 0.021) increase the risk of using these nets as fishing tools. The use of insecticide-treated mosquito nets against mosquitoes causes skin scratching and impairs breathing because of the impregnation products, as reported by respondents. Conclusion: A high prevalence of inappropriate use of impregnated mosquito nets in fishing practices is highlighted in this study. Interviews in the field revealed that nets are diverted for fishing purposes to increase the volume of catches. Consequently, it will be appropriate to assess the pyrethroid content in water and fishery products.

Discussion of reasonable drilling parameters in impregnated diamond bit drilling

The impregnated diamond(ID)bit drilling is one of the main rotary drilling methods in hard rock drilling and it is widely used in mineral exploration,oil and gas exploration,mining,and construction industries.In this study,the quadratic polynomial model in ID bit drilling process was proposed as a function of controllable mechanical operating parameters,such as weight on bit(WOB)and revolutions per minute(RPM).Also,artificial neural networks(ANN)model for predicting the rate of penetration(ROP)was developed using datasets acquired during the drilling operation.The relationships among mechanical operating parameters(WOB and RPM)and ROP in ID bit drilling were analyzed using estimated quadratic polynomial model and trained ANN model.The results show that ROP has an exponential relationship with WOB,whereas ROP has linear relationship with RPM.Finally,the optimal regime of mechanical drilling parameters to achieve high ROP was confirmed using proposed model in combination with rock breaking principal.

Green Superhydrophobic Paper with Self-cleaning Properties Prepared via One-step Impregnation

In this study,a green and pollution-free multifunctional superhydrophobic paper-based material was prepared using a simple and efficient dipping method.The superhydrophobic paper with a water contact angle(WCA)of 160°was prepared by attaching micro-and nanocomposite particles,made of stearic acid-modified chitosan and two kinds of titanium dioxide(TiO_(2))nanoparticles of different sizes,to a paper substrate.The surface morphology,elemental composition,and wetting properties of the coatings were examined using scanning electron microscopy(SEM),X-ray photoelectron spectroscopy(XPS),Fourier transform infrared spectroscopy(FT-IR),and contact angle measurements.Additionally,superhydrophobic coatings exhibited good self-cleaning properties,liquid repellency,ease of repair,and antifouling properties in organic solutions.

Preparation of hierarchical mesoporous Zn/HZSM-5 catalyst and its application in MTG reaction

The hierarchical mesoporous Zn/ZSM-5 zeolite catalyst was prepared by NaOH treatment and Zn impregnation, and its application in the conversion of methanol to gasoline （MTG） was studied. N2 adsorption-desorption results showed that the mesopores with sizes of 2-20 nm in HZ5/0.3AT was formed by 0.3 M NaOH alkali treatment. The zeolite samples after modification were also characterized by XRF, AAS, XRD, SEM and NH3-TPD methods. Zn impregnated catalyst Zn/HZ5/0.3AT exhibited dramatic improvements in catalytic lifetime and liquid hydrocarbons yield. The selectivity of aromatic hydrocarbons was also improved after Zn impregnation. It is suggested that the mesopores of Zn/HZ5/0.3AT enhanced the synergetic effect of Zn species and acid sites and the capability to coke tolerance, which were confirmed by the results of catalytic test and TGA analysis, respectively.

伏羲文化──中国传统文化之源

伏羲指上古畜牧业时融合许多部落文化的一个时代．伏羲文化指涵盖伏羲时代精神及物化的精神为主要内容、由后世不断丰富、对后世产生深远影响的远古文化，对中国传统哲学、婚姻家庭形态、生产力的发展、华夏民族的融合都产生了极大影响，成为中国传统文化的源泉．本文从伏羲文化的价值及其对中国传统文化的影响两个方面探讨了以上问题．

Dry Friction and Wear Characteristics of Impregnated Graphite in a Corrosive Environment

Tribological properties of impregnated graphite are greatly influenced by preparation technology and working conditions and it’s highly susceptible to corrosion environmental impacts,but the experimental research about it are few.In this paper,three kinds of impregnated graphite samples are prepared with different degree of graphitization,the tribological properties of these samples in the dry friction environment and in a corrosive environment are analyzed and contrasted.The tribo-test results show that the friction coefficient of samples is reduced and the amount of wear of samples increase when the graphitization degree of samples increases in dry friction condition.While in a corrosive environment（samples are soaked N2O4）,the friction coefficient and amount of wear are changed little if the graphitization degree of samples are low.If the degree of graphitization increase,the friction coefficient and amount of wear of samples increase too,the amount of wear is 2 to 3 times as the samples tested in the non-corrosive environment under pv value of 30MPa？m/s.The impregnated graphite,which friction coefficient is stable and graphitization degree is in mid level,such#2,is more appropriate to have a work in the corrosion conditions.In this paper,preparation and tribological properties especially in corrosive environment of the impregnated graphite is studied,the research conclusion can provide an experimental and theoretical basis for the selection and process improvement of graphite materials,and also provide some important design parameters for contact seal works in a corrosive environment.

Effects of impregnation sequence on the microstructure and performances of Cu-Co based catalysts for the synthesis of higher alcohols

Silica-supported CuCo catalysts were prepared by impregnation method with different impregnation sequence for higher alcohols synthesis. These catalysts were characterized by H2-TPR, XRD, N2 adsorption, XPS techniques and CO selective hydrogenation reaction measurement. The effects of impregnation sequence on the structure and performance of catalysts were investigated, and there were important influences on the selectivity to higher alcohols. There was a strong synergistic effect between copper and cobalt for the co-impregnated sample. The CuCo/SiO2 catalyst prepared by co- impregnation showed a better yield of total alcohols, and a higher selectivity to total alcohols which reached 51.5%.

Aromatization over nanosized Ga-containing ZSM-5 zeolites prepared by different methods:Effect of acidity of active Ga species on the catalytic performance

Nanosized Ga-containing ZSM-5 zeolites were prepared via isomorphous substitution and impregnation followed by characterized using various techniques. The catalytic performance of the zeolites for the aromatization of 1-hexene was investigated. The results indicate that isomorphous substitution promotes the incorporation of Ga heteroatoms into the framework along with the formation of extra-framework GaO;species（[GaO;]a） that have stronger interactions with the negative potential of the framework. In addition, based on the Py-IR results and catalytic performance, the [GaO;]aspecies with stronger Lewis acid sites produced a better synergism with moderate Br?nsted acid sites and thus improved the selectivity to aromatic compounds. However, the impregnation results in the formation of Ga;O;phase and small amounts of GaO;species that are mainly located on the external surface（[GaO;];）, which contribute to weaker Lewis acid sites due to weaker interactions with the zeolite framework. During 1-hexene aromatization, the nanosized Ga isomorphously substituted ZSM-5 zeolite samples（Gax-NZ5） exhibited better catalytic performance compared to the impregnated samples, and the highest aromatic yield（i.e.,65.4 wt%） was achieved over the Ga4.2-NZ5 sample, which contained with the highest Ga content.

Characterization of molten 2LiF–BeF_2 salt impregnated into graphite matrix of fuel elements for thorium molten salt reactor

The impregnation behavior of molten 2LiF–BeF_2(FLiBe) salt into a graphite matrix of fuel elements for a solid fuel thorium molten salt reactor(TMSR-SF) at pressures varying from 0.4 to 1.0 MPa was studied by mercury intrusion, molten salt impregnation, X-ray diffraction, and scanning electron microscopy techniques.It was found that the entrance pore diameter of the graphite matrix is less than 1.0 μm and the contact angle is about 135°. The threshold impregnation pressure was found to be around 0.6 MPa experimentally, consistent with the predicted value of 0.57 MPa by the Washburn equation. With the increase of pressure from 0.6 to 1.0 MPa, the average weight gain of the matrix increased from 3.05 to 10.48%,corresponding to an impregnation volume increase from 2.74 to 9.40%. The diffraction patterns of FLiBe are found in matrices with high impregnation pressures(0.8 MPa and1.0 MPa). The FLiBe with sizes varying from tens of nanometers to a micrometer mainly occupies the open pores in the graphite matrix. The graphite matrix could inhibit the impregnation of the molten salt in the TMSR-SF with a maximum operation pressure of less than 0.5 MPa.

Amine-silica composites for CO_2 capture: A short review

Amine-silica composite materials for post-combustion COcapture have attracted considerable attention because of their high COuptake at low COconcentrations, excellent COcapture selectivity in the presence of moisture, and lower energy requirements for sorbent regeneration. This review discusses the recent advances in amine-silica composites for COcapture, including adsorbent preparation and characterization, COcapture under dry and moisture conditions at different COpartial pressures, sorbent regeneration, and stability after many cyclic sorption-desorption runs.

Impact of impregnation pressure on desulfurization performance of Zn-based sorbents supported on semi-coke

High-pressure impregnation, a new preparation method for sorbents to remove H2S from hot coal gas, is introduced in this paper. Semi-coke （SC） and ZnO is selected as the support and active component of sorbent, respectively. The sorbent preparation process includes high-pressure impregnation, filtration, ovendry and calcination. The aim of this research is to primarily study the effects of the impregnation pressure on physical properties and desulfurization ability of the sorbent. The desulfurization experiment was carried out in a fixed-bed reactor at 500 ~C and a simulated coal gas used in this work was composed of CO （33 vol%）, H2 （39 vol%）, H2S （300 ppm in volume）, and N2 （balance）. Experimental results show that the pore structure of the SC support can be improved effectively and ZnO active component can be uniformly dispersed on the support, with the small particle size of 10-500 nm. Sorbents prepared using high-pressure impregnation have better desulfurization capacity and their active components have higher utilization rate. P20-ZnSC sorbent, obtained by high-pressure impregnation at 20 atm, has the best desulfurization ability with a sulfur capacity of 7.54 g S/100g sorbent and a breakthrough time of 44 h. Its desulfurization precision and efficiency of removing H2S from the middle temperature gases can reach 〈 1 ppm and 〉99.7%, respectively, before sorbent breakthrough.

Effect of cobalt and its adding sequence on the catalytic performance of MoO_3/Al_2O_3 toward sulfur-resistant methanation

The effect of promoter cobalt and the sequences of adding cobalt and molybdenum precursors on the performance of sulfur-resistant methanation were investigated. All these samples were prepared by impregnation method and characterized by N2-adsorption, X-ray diffraction(XRD), temperature-programmed reduction(TPR) and laser Raman spectroscopy(LRS). The conversions of CO for Mo-Co/Al, Co-Mo/Al and CoMo/Al catalysts were 59.7%, 54.3% and 53.9%, respectively. Among these catalysts, the Mo-Co/Al catalyst prepared stepwisely by impregnating Mo precursor firstly showed the best catalytic performance. Meanwhile, the conversions of CO were 48.9% for Mo/Al catalyst and 10.5% for Co/Al catalyst. The addition of cobalt species could improve the catalytic activity of Mo/Al catalyst. The N2-adsorption results showed that Co-Mo/Al catalyst had the smallest specific surface area among these catalysts. CoMoO4species in CoMo/Al catalyst were detected with XRD, TPR and LRS. Moreover, crystal MoS2which was reported to be less active than amorphous MoS2was found in both Co-Mo/Al and CoMo/Al catalysts. Mo-Co/Al catalyst showed the best catalytic performance as it had an appropriate surface structure, i.e., no crystal MoS2and very little CoMoO4species.

Effects of Rare Earth and Hot Pressing Sintering Temperature on the Transverse Rupture Strength of Fe-based Diamond Composites

Effects of sintering temperature in hot pressing, t yp es, states and amounts of rare earth as well as TiH 2 on the transverse rupture strength (TRS) of Fe-based composites are studied by means of orthogonal test and variance analysis in this paper. It is found that sintering temperature has a significant effect on the TRS of Fe-based diamond composites. The optimal sin tering temperature is 780～860 ℃. On the contrary, the effects of RE additi v es on values of TRS of the diamond composites have on distinct difference no mat ter the RE is in the state of mixture or compound or oxidization. Experimental r esults demonstrate that Fe-based diamond composites with RE additives exhibit h igher TRS, which results in an increase in diamond retention capacity. The degre e of increment of TRS is different at different sintering temperatures. The opti mal amount of rare earth was found to be about 1% in weight. The effect of RE is more significant at lower sintering temperature. The experimental results also reveal that TiH 2 additive has a negative effect on the TRS of Fe-based compos ites. Microscope observations demonstrate that specimen without TiH 2 additives , shows fewer pores and denser structures in the base metal. It can also be seen from the SEM observation of the resulting fracturing surface of bending test sp ecimens that the bonding of the diamond-matrix interface is better in the speci men without TiH 2 than in the specimen with TiH 2. Also the fracture surface o f the specimen without TiH 2 reveals ductile cup and cone behavior.