The impacts of gas impurities on the minimum miscibility pressure of injected CO_2-rich gas–crude oil systems and enhanced oil recovery potential

An effective parameter in the miscible-CO_2 enhanced oil recovery procedure is the minimum miscibility pressure(MMP)defined as the lowest pressure that the oil in place and the injected gas into reservoir achieve miscibility at a given temperature. Flue gases released from power plants can provide an available source of CO_2,which would otherwise be emitted to the atmosphere, for injection into a reservoir. However, the costs related to gas extraction from flue gases is potentially high. Hence, greater understanding the role of impurities in miscibility characteristics between CO_2 and reservoir fluids helps to establish which impurities are tolerable and which are not. In this study, we simulate the effects of the impurities nitrogen(N_2), methane(C_1), ethane(C_2) and propane(C_3) on CO_2 MMP. The simulation results reveal that,as an impurity, nitrogen increases CO_2–oil MMP more so than methane. On the other hand, increasing the propane(C_3)content can lead to a significant decrease in CO_2 MMP, whereas varying the concentrations of ethane(C_2) does not have a significant effect on the minimum miscibility pressure of reservoir crude oil and CO_2 gas. The novel relationships established are particularly valuable in circumstances where MMP experimental data are not available.

Quantitation of Genetox Impurities Using a Surrogate Standard Approach

With the ever increasing complexity of active pharmaceutical ingredient (API) preparations, more potential genotoxic impurities (PGI’s) are being observed. It is thus necessary to determine if these PGI’s are present in the final API’s, and if they are present, to ensure the levels are acceptable for any clinical uses. For PGI’s that have authentic standards available, quantitation can be accomplished in a straightforward manner. However, for PGI’s that are expected to form through rearrangements or side reactions, authentic standards may not be readily available, significantly complicating the analysis. In this study we describe a surrogate standard approach for quantifying PGI’s that allows for relative response factor calculations of PGI species utilizing both gas chromatography-mass spectrometry (GC-MS) and liquid chromatography-mass spectrometry (LC-MS).

EFFECT OF INTERSTITIAL IMPURITIES ON THE PHASETRANSFORMATION OF Ti-Al ALLOYS

应用固体与分子经验电子理论的平均晶胞和平均原子模型分析计算了间隙杂质对Ti-Al合金价电子结构和相变的影响。同时根据该理论的键能公式计算了间隙杂质影响下的键能、熔点和液相线的变化。据此解释了Ti-Al合金相变目前尚有争议的主要实验结果。表明，间隙杂质提高了合金元素的原子杂阶，引起键结构呈严重的各向异性，阻碍了β→α相转变，导致中间成分相变的复杂性。间隙杂质也降低了熔点及高温液相线，采用近似处理由该理论可较好地计算其平均降低程度。

Light-absorbing impurities on Keqikaer Glacier in western Tien Shan: concentrations and potential impact on albedo reduction

Light-absorbing impurities on glaciers are important factors that influence glacial surface albedo and accelerate glacier melt. In this study, the quantity of light-absorbing impurities on Keqikaer Glacier in western Tien Shan, Central Asia, was measured. We found that the average concentrations of black carbon was 2,180 ng/g, with a range from 250 ng/g to more than 10,000 ng/g. The average concentrations of organic carbon and mineral dust were 1,738 ng/g and 194 μg/g, respectively. Based on simulations performed with the Snow Ice Aerosol Radiative model simulations, black carbon and dust are responsible for approximately 64% and 9%, respectively, of the albedo reduction, and are associated with instantaneous radiative forcing of 323.18 W/m2(ranging from 142.16 to 619.25 W/m2) and 24.05 W/m2(ranging from 0.15 to69.77 W/m2), respectively. For different scenarios, the albedo and radiative forcing effect of black carbon is considerably greater than that of dust. The estimated radiative forcing at Keqikaer Glacier is higher than most similar values estimated by previous studies on the Tibetan Plateau, perhaps as a result of black carbon enrichment by melt scavenging. Light-absorbing impurities deposited on Keqikaer Glacier appear to mainly originate from central Asia, Siberia, western China(including the Taklimakan Desert) and parts of South Asia in summer, and from the Middle East and Central Asia in winter.A footprint analysis indicates that a large fraction(>60%) of the black carbon contributions on Keqikaer Glacier comes from anthropogenic sources. These results provide a scientific basis for regional mitigation efforts to reduce black carbon.

Influence of nitrogen impurities on the characteristics of a patterned helium dielectric barrier discharge at atmospheric pressure

In this paper, a two-dimensional axisymmetric fluid model was established to investigate the influence of nitrogen impurity content on the discharge pattern and the relevant discharge characteristics in an atmosphere pressure helium dielectric barrier discharge(DBD). The results indicated that when the nitrogen content was increased from 1 to 100 ppm, the discharge pattern evolved from a concentric-ring pattern into a uniform pattern, and then returned to the concentricring pattern. In this process, the discharge mode at the current peak moment transformed from glow mode into Townsend mode, and then returned to glow mode. Further analyses revealed that with the increase of impurity level, the rate of Penning ionization at the pre-ionization stage increased at first and decreased afterwards, resulting in a similar evolution pattern of seed electron level. This evolution trend was believed to be resulted from the competition between the N2 partial pressure and the consumption rate of metastable species. Moreover, the discharge uniformity was found positively correlated with the spatial uniformity of seed electron density as well as the seed electron level. The reason for this correlation was explained by the reduction of radial electric field strength and the promotion of seed electron uniformity as pre-ionization level increases. The results obtained in this work may help better understand the pattern formation mechanism of atmospheric helium DBD under the variation of N2 impurity level, thereby providing a possible means of regulating the discharge performance in practical application scenarios.

EFFECTS OF INTERSTITIAL IMPURITIES ON PHASE TRANSFORMATION OF Ti-Al ALLOYS

１ＩＮＴＲＯＤＵＣＴＩＯＮＴｈｅｔｉｔａｎｉｕｍａｌｕｍｉｎｉｄｅｃｏｍｐｏｕｎｄｓｈａｖｅｒｅｃｅｉｖｅｄｃｏｎｓｉｄｅｒａｂｌｅａｔｅｎｔｉｏｎｒｅｃｅｎｔｌｙａｓｃａｎｄｉｄａｔｅｍａｔｅｒｉａｌｓｆｏｒｒｅｌａｔｉｖｅｌｙｈｉｇｈｔｅｍ...

Determination of Impurities and Degradation Products/Causes for <i>m</i>-Iodobenzylguanidine Using HPLC-Tandem Mass Spectrometry

m-Iodobenzylguanidinium hemisulfate (MIBGHS) is a precursor in the preparation of radioiodine-labeled m-iodobenzylguanidine (MIBG), which is used as a radio-imaging and therapy agent for neuroendocrine tumors and myocardial sympathetic nerve function. To ensure the quality and efficacy of the medicine and prevent side effects, the precursor purity, source of impurity, and derivatives have to be determined. In this study, the purity of synthesized MIBGHS and the amount of contaminants therein were determined by high-performance liquid chromatography and ultraviolet detection, gradient eluted by ammonium formate aqueous solution and acetonitrile mobile phase on both C8 and phenyl type column. The impurities were identified on the basis of molecular and fragmented ion mass spectra using of electrospray ionization triple quadrupole tandem mass spectrometry. The results revealed the presence of process-related impurities including m-bromobenzylguanidine (MBrBG) and overreacted byproducts. Stress test results indicated that MIBGHS is stable under acidic and dry thermal conditions for at least 72 h but MIBG aqueous solution was deteriorated slowly when exposed to UV light, thermal, oxidative and alkaline environments. Thus, m-iodobenzylamine, the starting material intended for the synthesis of MIBGHS should be analyzed to ensure that it is free from m-bromobenzylamine impurity. Stored under normal condition (-18°C), MIBGHS is stable for at least 12 months. The chemically labile guanidine and amine groups in MIBGHS are the major causes of its instability, while iodide loss from the phenyl group is a minor cause.

MEASURING THE IMPURITIES AND NEPS ON COTTON GRAY GOODS BY IMAGE ANALYSIS

In this paper, a test system was developed in which a CCD camera was used as a sensor together with an IBM-AT-compatible computer with an Intel 80486 processor to measure the impurities and neps on a piece of cotton gray goods, and a method was proposed by which the differences of degree of gray between samples and interference caused by surface unevenness, creasing and the like within a test sample can be removed effectively. The whole test system is reliable, accurate and causing fewer subjective errors.

Role of trivalent antimony in the removal of As, Sb, and Bi impurities from copper electrolytes

The role of trivalent antimony was investigated in removing As, Sb, and Bi impurities from a copper electrolyte. Puri- fication experiments were carried out by adding a various concentrations of Sb（III） ions in a synthetic electrolyte containing 185 g/L sulfuric acid, 45 g/L Cu2＋, 10 g/L As, and 0.5 g/L Bi under stirring at 65℃ for 2 h. The electrolyte was filtered, and the structure, morphology and composition of the precipitate were analyzed by means of chemical analysis, scanning electron mi- croscopy （SEM）, X-ray diffraction （XRD）, transmission electron microscopy （TEM）, and IR spectroscopy. The precipitate is composed of irregular lumps which are agglomerated by fine dendritic and floccus particles, and it mainly consists of As, Sb, Bi, and O elements. Characteristic bands in the IR spectra of the precipitate are As-OX （X=As, Sb, Bi）, Sb-OY （Y=Sb, Bi）, O-As-O1 As-OH, Sb-OH, and O-H. The precipitate is a mixture of microcrystalline SbAsQ, （Sb,As）203, and amorphous phases. As, Sb, and Bi impurities are effectively removed from the copper electrolyte by Sb（III） ions attributing to these pre- cipitates.

Thermodynamic behavior and morphology of impurities in metallurgical grade silicon in process of O_2 blowing

Gas blowing is a valid method to remove the impurities from metallurgical grade silicon（MG-Si） melt.The thermodynamic behavior of impurities Fe,Al,Ca,Ti,Cu,C,B and P in MG-Si was studied in the process of O2 blowing.The removal efficiencies of impurities in MG-Si were investigated using O2 blowing in ladle.It is found that the removal efficiencies are higher than 90% for Ca and Al and nearly 50% for B and Ti.The morphology of inclusions was analyzed and the phases Al3Ni,NiSi2 and Al3Ni were confirmed in MG-Si by X-ray diffraction.It was found that SiB4 exists in Si？B binary system.The chemical composition of inclusions in MG-Si before and after refining was analyzed by SEM-EDS.It is found that the amount of white inclusion reduces for the removal of most Al and Ca in the forms of molten slag inclusion and the contents of Fe,Ni and Mn in inclusion increase for their inertia in silicon melt with O2 blowing.

Effect of inorganic salt impurities on seeded precipitation of silica hydrate from sodium silicate solution

To clarify the precipitation of silica hydrate from the real desilication solutions of aluminosilicate solid wastes by adding seeds and improve integrated waste utilization,the seeded precipitation was studied using synthesized sodium silicate solution containing different inorganic salt impurities.The results show that sodium chloride,sodium sulfate,sodium carbonate,or calcium chloride can change the siloxy group structure.The number of high-polymeric siloxy groups decreases with increasing sodium chloride or sodium sulfate concentration,which is detrimental to seeded precipitation.Calcium chloride favors the polymerization of silicate ions,and even the chain groups precipitate with the precipitation of high-polymeric sheet and cage-like siloxy groups.The introduced sodium cations in sodium carbonate render a more open network structure of high-polymeric siloxy groups,although the carbonate ions favor the polymerization of siloxy groups.No matter how the four impurities affect the siloxy group structure,the precipitates are always amorphous opal-A silica hydrate.

Removal of Metallic Impurities from Off-Grade Copper Concentrate in Alkaline Solution

The removal of metallic impurities from off-grade copper concentrate was investigated in alkaline solution with H2O2. The analysis results of XRD and SEM-EDS revealed the oxidative mechanisms of all sulfides. The influence of various parameters of alkaline leaching were investigated including concentrations of sodium hydroxide and hydrogen peroxide, liquid to solid ratio, leaching time and temperature. The results showed that the removal rate of Mo, As and Zn were increased with increasing leaching time and H2O2 concentration, and that the removal rate of Mo, As and Zn were firstly increased and then slightly decreased with increasing liquid to solid ratio, temperature and NaOH concentration, respectively. More than 95% Mo, 94% As, and 94 % Zn are removed from the off-grade concentrate under the optimum conditions, while only 1.7% Cu is dissolved. These optimum conditions were sodium hydroxide 1.5 mol/L, hydrogen peroxide 1.0 mol/L, temperature 50&deg;C, liquid to solid ratio 5/1 mL/g and leaching time 5 h.

Quantification of Structurally Alert Mutagenic Impurities in Meropenem Trihydrate Drug Substance by Liquid Chromatography with High Resolution Mass Spectrometer (LC-HRMS)

Potential mutagenic impurities in Active Pharmaceutical Ingredient, Meropenem Trihydrate were assessed and a novel analytical method for their quantification was developed and validated. This Liquid Chromatographic method using High Resolution Mass Spectrometer (LC-HRMS) technique is proved to be suitable for simultaneous quantification of all ten identified impurities with required specificity, sensitivity, resolution, precision, accuracy, and other method characteristics as per ICH Guidelines. The acceptable limit of less than 2.9 μg/g was considered for evaluations, based on drug substance dosage and duration of treatment. The method stands most sensitive with a Limit of Detection of 0.35 μg/g, considering the challenge full acceptance criteria as per current regulatory standards.

Analysis of Polymer Impurities in Cephalosporin Antibiotics

[Objectives]To establish a HPLC-MS method for the determination of polymer impurities in cefathiamidine and its preparations.[Methods]Kromasil 100-5 C_(18) column(4.6 mm ×250 mm,5μm)was used for analysis;mobile phase ammonium acetate solution(pH 6.30)-acetonitrile,gradient elution;volumetric flow rate 1.0 mL/min;column temperature 40℃;multi-reaction monitoring mode was used for analysis,and positive ion scanning was chosen as the electrospray ion source.[Results]The resolution between impurities and main peaks under this method was greater than 1.5,and 8 known impurities and 2 polymer impurities could be completely separated and distinguish-ed.It was inferred that the molecular ion peak[M+H]^(+):m/z727.1874,m/z 785.1937 was the possible polymer impurity of this product.[Conclusions]A method for the analysis of polymer impurities in cefathiamidine and its preparations was formed,which could achieve the purpose of simultaneous analysis of small molecule impurities and polymer impurities,and could better control the content of single impurities in the polymer,providing a reliable inspection basis for strict control of cefathiamidine quality.

A review of electrolyte additives and impurities in vanadium redox flow batteries

As one of the most important components of the vanadium redox flow battery （VRFB）, the electrolyte can impose a significant impact on cell properties, performance and capital cost. In particular, the electrolyte composition will influence energy density, operating temperature range and the practical applications of the VRFB. Various approaches to increase the energy density and operating temperature range have been proposed. The presence of electrolyte impurities, or the addition of a small amount of other chemical species into the vanadium solution can alter the stability of the electrolyte and influence cell perfor- mance, operating temperature range, energy density, electrochemical kinetics and cost effectiveness. This review provides a detailed overview of research on electrolyte additives including stabilizing agents, im- mobilizing agents, kinetic enhancers, as well as electrolyte impurities and chemical reductants that can be used for different purposes in the VRFBs.

Electronic Theoretical Study of the Interaction between Rare Earth Elements and Impurities at Grain Boundaries in Steel

The model of dislocations was used to construct the model of grain boundary (GB) with pure rare earths, and rare earth elements and impurities. The influence of the interaction between rare earth elements and impurities on the cohesive properties of 5.3° low angle GB of Fe was investigated by the recursion method. The calculated results of environment sensitive embeding energy( E ESE ) show that the preferential segregation of rare earth elements towards GBs exists. Calculations of bond order integrals (BOI) show that rare earth elements increase the cohesive strength of low angle GB, and impurities such as S, P weaken the intergranular cohesion of the GB. So rare earth element of proper quantity added in steel not only cleanses other harmful impurities off the GBs, but also enhances the intergranular cohesion. This elucidates the action mechanism of rare earth elements in steel from electronic level and offers theoretical evidence for applications of rare earth elements in steels.

Effects of grinding environment and lattice impurities on spodumene flotation

The effect of grinding on the spodumene flotation was investigated. The flotation response of spodumene ground by different mills was different, due to the variation of metal ions on spodumene surfaces caused by grinding environments and/or impurities. The samples were subjected to acid pickling treatment to remove most of the metal ions from the surfaces, and then all samples showed the same poor flotation response, which confirmed the significance of surface metal ions. Metal ion impurities may come from both grinding environments and lattice substitutions in spodumene. Density functional theory (DFT) calculation revealed that Fe and Ca could exist as lattice substitutions on the spodumene surface while Mg substitution is unlikely to occur. Furthermore, Fe is considered to be active site for the absorption of sodium oleate on the spodumene surface. Morphology analysis showed differences in particle size and shape for samples ground by different mills, resulting in different amounts of exposed surfaces. The particle size, cleavage characteristics caused by grinding environments, and metal ion impurities originated from grinding and isomorphous substitutions, play significant roles in the chemisorption of collector on the spodumene surface.

Effect of impurities in recycling water on Pb-Ag anode passivation in zinc electrowinning process

Effect of impurities in recycling water on Pb-Ag anode passivation in zinc electrowinning process was investigated by linear scan voltammetry.Results show that passivation process would be affected in the presence of Cl^-and F-in recycling water.It was highly advantageous to take H2SO4 concentration as 180g/L,Mn^2＋ concentration as 3-5 g/L and F-less than 42mg/L.However,passivation process would not be affected when Cl^-concentration was less than 13mg/L without any other ions,or when mass ratio of Mn^2＋ to Cl^-existing in electrolyte was 8,where Cl^-concentration could reach up to 625mg/L.

THE SEPARATION CRITERION OF IMPURITIES IN CRUDE METALS BY VACUUM DISTILLATION

ＴＨＥＳＥＰＡＲＡＴＩＯＮＣＲＩＴＥＲＩＯＮＯＦＩＭＰＵＲＩＴＩＥＳＩＮＣＲＵＤＥＭＥＴＡＬＳＢＹＶＡＣＵＵＭＤＩＳＴＩＬＬＡＴＩＯＮ￥Ｌｉｕ，Ｒｉｘｉｎ（ＩｎｓｔｉｔｕｔｅｏｆＣｈｅｍｉｃａｌＭｅｔａｌｌｕｒｇｙ，ＣｈｉｎｅｓｅＡｃａｄｅｍｙｏｆＳ...

Influence of impurities on microstructure and mechanical properties of ZK60 magnesium alloy

The influence of impurity content on the microstructure and mechanical properties of ZK60 magnesium alloys was investigated by optical microscopy,scanning electron microscopy and tensile test.ZK60 alloys were prepared by changing holding time of alloy melt during semi-continuous casting in order to control the content of impurity elements.The alloy with lower purity content is found to have less second precipitates and larger grain size in the as-cast state.However,in the as-extruded state,reducing impurities brings about a decrease in grain size and an increase in yield strength from 244 MPa to 268 MPa,while the elongations in the as-extruded alloys with different contents of impurities are almost the same.After T5 treatment,impurity content is found to have more obvious effect on the yield strength of ZK60 alloy.The yield strength of ZK60-45 alloys with low impurity content is increased up to 295 MPa after T5 treatment.