Assessing mixing uniformity in microreactors via in-line spectroscopy

Mixing behavior is critical for enhancing the selectivity of fast chemical reactions in microreactors.A high Reynolds number(Re)improves the mixing rate and selectivity of the reactions,but some exceptions of increasing side product yield with the higher Re have been reported.This study investigated the mixing uniformity in microreactors with in-line UV-vis spectroscopy to clarify the relationship between reaction selectivity and chaotic mixing with the higher Re.A colorization experiment of thymolphthalein in an acidic solution was conducted with an excess acid amount to the base to indicate a non-uniformly mixed region.Non-uniformity significantly increased with Re.At the same time,the degree of mixing,which was measured by a usual decolorization experiment,showed that the mixing rate increased with Re.The in-line analysis of the Villermaux-Dushman reaction during the mixing clarified that side product yield significantly increased with Re at around 300 and then decreased at around 1100.These results suggest the compensation effect between the mixing uniformity and mixing rate on the selectivity of the mixing-sensitive reactions.Faster mixing,characterized by a larger Re,can disturb mixing uniformity and,in some cases,decrease reaction selectivity.

Accelerated generation of holograms with ultra-low memory symmetrically high-compressed look-up table

Computer-generated holography technology has been widely applied,and as research in this field deepens,the demand for memory and computational power in small AR and VR devices continues to increase.This paper presents a hologram generation method,i.e.,a symmetrically high-compressed look-up table method,which can reduce memory usage by50%.In offline computing,half of the basic horizontal and vertical modulation factors are stored,halving the memory requirements without affecting inline speed.Currently,its potential extends to various holographic applications,including the production of optical diffraction elements.

Multi-dimensional multiplexing optical secret sharing framework with cascaded liquid crystal holograms

Secret sharing is a promising technology for information encryption by splitting the secret information into different shares.However,the traditional scheme suffers from information leakage in decryption process since the amount of available information channels is limited.Herein,we propose and demonstrate an optical secret sharing framework based on the multi-dimensional multiplexing liquid crystal(LC)holograms.The LC holograms are used as spatially separated shares to carry secret images.The polarization of the incident light and the distance between different shares are served as secret keys,which can significantly improve the information security and capacity.Besides,the decryption condition is also restricted by the applied external voltage due to the variant diffraction efficiency,which further increases the information security.In implementation,an artificial neural network(ANN)model is developed to carefully design the phase distribution of each LC hologram.With the advantage of high security,high capacity and simple configuration,our optical secret sharing framework has great potentials in optical encryption and dynamic holographic display.

Implementation of natural hand gestures in holograms for 3D object manipulation

Holograms provide a characteristic manner to display and convey information, and have been improved to provide better user interactions Holographic interactions are important as they improve user interactions with virtual objects. Gesture interaction is a recent research topic, as it allows users to use their bare hands to directly interact with the hologram. However, it remains unclear whether real hand gestures are well suited for hologram applications. Therefore, we discuss the development process and implementation of three-dimensional object manipulation using natural hand gestures in a hologram. We describe the design and development process for hologram applications and its integration with real hand gesture interactions as initial findings. Experimental results from Nasa TLX form are discussed. Based on the findings, we actualize the user interactions in the hologram.

Discrete multi-step phase hologram for high frequency acoustic modulation

Acoustic holograms can recover wavefront stored acoustic field information and produce high-fidelity complex acoustic fields. Benefiting from the huge spatial information that traditional acoustic elements cannot match, acoustic holograms pursue the realization of high-resolution complex acoustic fields and gradually tend to high-frequency ultrasound applications. However, conventional continuous phase holograms are limited by three-dimensional(3D) printing size, and the presence of unavoidable small printing errors makes it difficult to achieve acoustic field reconstruction at high frequency accuracy. Here, we present an optimized discrete multi-step phase hologram. It can ensure the reconstruction quality of image with high robustness, and properly lower the requirement for the 3D printing accuracy. Meanwhile, the concept of reconstruction similarity is proposed to refine a measure of acoustic field quality. In addition, the realized complex acoustic field at 20 MHz promotes the application of acoustic holograms at high frequencies and provides a new way to generate high-fidelity acoustic fields.

The prediction on in-line vortex-induced vibration of slender marine structures

The in-line （IL） vortex-induced vibration （VIV） that occurs frequently in ocean engineering may cause severe fatigue damage in slender marine structures. To the best knowledge of the authors, in existing literatures, there is no efficient analytical model for predicting pure IL VIV. In this paper, a wake oscillator model capable of analyzing the IL VIV of slender marine structures has been developed. Two different kinds of van der Pol equations are used to describe the near wake dynamics related to the fluctuating nature of symmetric vortex shedding in the first excitation region and alternate vortex shedding in the second one. Some comparisons are carried out between the present model results and experimental data. It is found that many phenomena observed in experiments could be reproduced by the present wake oscillator model.

Experimental Study on Coupled Cross-Flow and in-Line Vortex-Induced Vibration of Flexible Risers

In this work, we study the coupled cross-flow and in-line vortex-induced vibration （VIV） of a fixedly mounted flexible pipe, which is free to move in cross-flow （ Y- ） and in-line （ X- ） direction in a fluid flow where the mass and natural frequencies are precisely the same in both X- and Y-direction. The fluid speed varies from low to high with the corresponding vortex shedding frequency varying from below the first natural frequency to above the second natural frequency of the flexible pipe. Particular emphasis was placed on the investigation of the relationship between in-line and cross-flow vibration. The experimental results analyzed by using these measurements exhibits several valuable features.

Ultrafiltration with in-line coagulation for the removal of natural humic acid and membrane fouling mechanism

Experimental and theoretical analysis were made on the natural humic acid removal and the membrane fouling of ultrafiltration （UF） with in-line coagulation. The results showed dissolved organic carbon （DOC） and UV254 removals by the UF with in-line coagulation at pH 7 were increased from 28% to 53% and 40% to 78% in comparison with direct UF treatment respectively. At the same time, the analysis of high performance liquid chromatography showed that UF with coagulation had significant improvement of removal of humic acid with molecular weights less than 6000 Da in particular. Compared to direct UF, the in-line coagulation UF also kept more constant permeate flux and very slight increase oftransmembrane pressure during a filtration circle. Two typical membrane fouling models were used by inducing two coefficients Kc and Kp corresponding to cake filtration model and pore narrowing model respectively. It was found that membrane fouling by pore-narrowing effect was effectively alleviated and that by cake-filtration was much decreased by in-line coagulation. Under the condition of coagulation prior to ultrafiltration at pH 7, the cake layer formed on the membrane surface became thicker, but the membrane filtration resistance was lower than that at pH 5 with the extension of operation time.

In-line response of vertical cylinders in regular and random waves

The in-line response of a vertical flexibly mounted cylinder in regular and random waves is reported. Both theoretical analyses and experimental measurements have been performed. The theoretical predictions are based on the Morison equation which is solved by the incremental harmonic balance method. Experiments are then performed in a wave flume to determine the accuracy of the Morison equation in predicting the in-line response of the cylinder in regular and random waves. The interaction between waves and vibrating cylinders are investigated.

Three-axis magnetic flux leakage in-line inspection simulation based on finite-element analysis

With the increase of pipelines, corrosion leakage accidents happen frequently. Therefore, nondestructive testing technology is important for ensuring the safe operation of the pipelines and energy mining. In this paper, the structure and principle of magnetic flux leakage （MFL） in-line inspection system is introduced first. Besides, a mathematic model of the system according to the ampere circuit rule, flux continuity theorem, and column coordinate transform is built, and the magnetic flux density in every point of space is calculated based on the theory of finite element analysis. Then we analyze and design the disposition of measurement section probes and sensors combining both three-axis MFL in-line inspection and multi-sensor fusion technology. Its advantage is that the three-axis changes of magnetic flux leakage field are measured by the multi-probes at the same time, so we can determine various defects accurately. Finally, the theory of finite element analysis is used to build a finite element simulation model, and the relationship between defects and MFL inspection signals is studied. Simulation and experiment results verify that the method not only enhances the detection ability to different types of defects but also improves the precision and reliability of the inspection system.

Nonlinear Coupled in-Line and Cross-Flow Vortex-Induced Vibration Analysis of Top Tensioned Riser

The fluctuating furces of the fluid exerted on the top terrsioned riser （＇FIR） in the in-line and cross-flow directions are both modeled by van del Pol wake oscillator model and the nonlinear coupled dynamics of the in-line and cross-flow vortex-induced vibrations （VIV） of the riser are analyzed in time domain in this papar. The numencal shnulation results of the riser＇s in-line and cross-flow displacements and curvatures are compared with experimental measurements and the comparison shows the validity of this method in modeling some main features of the riser＇s VIV. Finally, the effects of the riser＇s top tensions and internal flow velocities on the coupled vibrations of the riser are investigated.

Anisotropic total variation minimization approach in in-line phase-contrast tomography and its application to correction of ring artifacts

In-line phase-contrast computed tomography（IL-PC-CT） imaging is a new physical and biochemical imaging method.IL-PC-CT has advantages compared to absorption CT when imaging soft tissues. In practical applications, ring artifacts which will reduce the image quality are commonly encountered in IL-PC-CT, and numerous correction methods exist to either pre-process the sinogram or post-process the reconstructed image. In this study, we develop an IL-PC-CT reconstruction method based on anisotropic total variation（TV） minimization. Using this method, the ring artifacts are corrected during the reconstruction process. This method is compared with two methods： a sinogram preprocessing correction technique based on wavelet-FFT filter and a reconstruction method based on isotropic TV. The correction results show that the proposed method can reduce visible ring artifacts while preserving the liver section details for real liver section synchrotron data.

Determination of inorganic anions in ethyl acetate by in-line hollow fiber membrane extraction with ion chromatography

In this work, a novel hollow fiber membrane extractor was set up to extract inorganic anions from ethyl acetate using deionized water. Inorganic anions in slightly soluble organic solvents can be determined by the in-line hollow fiber membrane extractor coupled with ion chromatography at first time. Different aspects of the extraction procedure such as magnetic stirring speed, extraction flow rate and extraction time were optimized to achieve high extraction efficiency and good separation results. Satisfactory linear range, limits of detection and good repeatability were obtained. The procedure was applied to analyze inorganic anions in two commercial ethyl acetate samples.

Grid-based computer-generated holograms synthesizing for holographic three-dimensional display

To reduce the computing time of composite computer-generated holograms （CGHs） gen- eration based upon the angular projection algorithm for holographic three-dimensional （3D） display, a grid-based holographic display （ GHD ） scheme was designed. The grid computing technology was applied to numerically process the different angular projections of an object in distributed-parallel manner to create the corresponding CGHs. The whole treatment of a projection was regarded as a job executed on the grid node machine. The number of jobs which were submitted to grid nodes, therefore, was equal to that of the projections of the object. A Condor-based grid testbed was constructed to verify the feasibility of the GHD scheme, and a graphical user interface （GUI） program and several service modules were developed for it. A 3D terrain model as an example was processed on the testbed. The result showed that the scheme was feasible and able to improve the execution elficiency greatly.

STUDY ON AUTOMATIC IN-LINE MEASUREMENT OF FeO CONTENT IN AGGLOMERATE

In this paper, the mechanism of physical method for measuring the FeO content in agglomerate replacing the chemical method is proposed after studying the electromagnetic property of the agglomerate. The microcomputer-measuring system for FeO content is provided. Attention is also paid to introducing the working principle of the H-type compensation sensor and the processing method of the measured data. This system has been successfully applied in practice to in-line measure the FeO content.

In-line phase contrast for weakly absorbing materials with a microfocus x-ray source

For weakly absorbing materials, image contrast can be enhanced by phase contrast in formation. The effectiveness of the in-line phase contrast technique relies on its ability to record intensity data which contain information on the x- ray＇s phase shift. Four kinds of approaches to the relationship between intensity distribution and phase shift axe reviewed and discussed. A micro-focal x-ray source with high geometrical magnification is used to acquire phase contrast images. A great improvement on image quality is shown and geometrical parameters axe modified for comparison between different imaging positions.

Large Eddy Simulation on Interaction Between in-Line and Cross-Flow Oscillation of A Circular Cylinder

This paper discusses numerical results from three-dimensional large eddy simulations of an oscillating cylinder under prescribed movements in uniform flow. Six cases, namely pure in-line, pure cross-flow and two groups of ＇Figure of Eight＇ oscillation patterns are under investigation at Reynolds number Re = 24000. The ＇ Figure of Eight＇ pattern in each group is with identical shape but oppusite orbital directions. The numerical results on hydrodynamic forces, higher order force components, and vortex shedding modes are extensively studied and compared with the measured experimental data. It is found that the fluid force in phase with the velocity, which represents the energy transfer between the fluid and the cylinder, has opposite sign and different magnitude due to the opposite orbital direction. Higher order force components in cross-flow direction are found to occur at odd nmnber times of the oscillating frequency, while even nmbers dominate the higher order force components in in-llne direction. The 2C and 2T vortex shedding modes are well reproduced due to the opposite orbital direction effect. Comparisons between numerical and experimental results indicate that the present numerical model could be a rational tool for the identification of hydrodynamic coefficients which are normally applied in empirical models to predict the vortex-induced vibrations of slender marine structures.

Influence of tube voltage and current on in-line phase contrast imaging using a microfocus x-ray source

In-line x-ray phase contrast imaging has attracted much attention due to two major advantages： its effectiveness in imaging weakly absorbing materials, and the simplicity of its facilities. In this paper a comprehensive theory based on Wigner distribution developed by Wu and Liu [Med. Phys. 31 2378-2384 （2004）] is reviewed. The influence of x-ray source and detector on the image is discussed. Experiments using a microfocus x-ray source and a CCD detector are conducted, which show the role of two key factors on imaging： the tube voltage and tube current. High tube current and moderate tube voltage are suggested for imaging.

Multimodal Imaging with 3D-Holograms for Preoperative Planning in Pediatric Cardiac Surgery:A Unique Case Report

Multimodal imaging,including augmented or mixed reality,transforms the physicians’interaction with clinical imaging,allowing more accurate data interpretation,better spatial resolution,and depth perception of the patient’s anatomy.We successfully overlay 3D holographic visualization to magnetic resonance imaging images for preoperative decision making of a complex case of cardiac tumour in a 7-year-old girl.

Design of in-line multipoint initiation control system

In order to improve the power of initiating explosive warheads, besides exploring new type of high explosive, multipoint initiation technology becomes the research focus. With research on electronic safety and arming devices （ESADs）, pulse power devices and slapper detonators, a hardware control circuit was designed for multipoint initiation control system based on complex programmable logic device （ CPLD ）. In addition, a real-time monitoring interface based on virtual instru- ments technology was designed by the prevailing software of Laboratory Virtual Instrument Engineer- ing Workbench （LabVIEW）. It provides users a real-time status of the hardware circuit system. Mo- reover, a series of experiments were done on the software and hardware platform. The results show that the signals transmission, collection, analysis and display can be realized reliably through a serial port line. It is verified that using a serial bus controller for multiple initiators is reasonable. Successful design of the platform will play an important foundation for the theory and engineering of the fu- ture weapon system. Surely, it will become one of the development directions for intelligent initia- tion system.