Management of incinerated sewage sludge ash(ISSA)and dredged contaminated marine sediments(CMSs)is a great challenge for Hong Kong and other coastal cities due to limited landfilling capacity.The present study investi...Management of incinerated sewage sludge ash(ISSA)and dredged contaminated marine sediments(CMSs)is a great challenge for Hong Kong and other coastal cities due to limited landfilling capacity.The present study investigates the use of high content(20%of sediment by mass)of ISSA in combination with cement/lime for solidification/stabilization(S/S)treatment of CMSs to provide a way to reuse the wastes as construction materials.The results showed that ISSA being a porous material was able to absorb a large amount of water rendering a more efficient solidification process of the marine sediment which normally had a very high water content(w80%).The S/S treatment improved the engineering properties of the sediment,but reduced the workability,especially for the lime-treated samples.Lime can be used to replace ordinary Portland cement(OPC)for better heavy metal immobilization and carbon emission reduction.The hardened sediment samples prepared with 10%of lime and 20%of ISSA could attain a strength of 1.6 MPa after 28 d of curing.In addition,leaching tests confirmed that there was no environmental risk induced by these stabilized materials.The formation of hydrated cementitious compounds including calcium silicate hydrate(CeSeH)/calcium aluminate silicate hydrate(C-A-S-H)/hydrocalumite/calcite was mainly responsible for the strength development in the ISSA/lime-treated sediments.展开更多
The compounds of aluminum phosphate are used to remove the fluorine compounds from wastewater. The fluorine removal agent using the ash of sewage sludge and the municipal waste in addition to sulfuric acid were invest...The compounds of aluminum phosphate are used to remove the fluorine compounds from wastewater. The fluorine removal agent using the ash of sewage sludge and the municipal waste in addition to sulfuric acid were investigated. The removal agent showed high removal performance, and the fluorine concentration of the treated water reached below 0.1 mg/L, and the noticeable elution of the harmful metals from the ashes were not found in this experiment.展开更多
Calcium-based compounds are used as fluorine removal treatment materials in water.However,due to the water solubility of calcium fluoride,there is a problem with low fluorine removal performance.For this reason,variou...Calcium-based compounds are used as fluorine removal treatment materials in water.However,due to the water solubility of calcium fluoride,there is a problem with low fluorine removal performance.For this reason,various removing agents including phosphorus have been developed.We have found that a combination of aluminum phosphate recovered from incinerated ash of the sewage sludge and refuse incineration ash has a high fluorine removal performance.At the highest removal performance,F ion concentration of the treated water reached 0.1 mg/L,so an optimal formulation method was investigated.展开更多
The phosphorus recovery from incinerated ash of sewage sludge by a heat treatment method was investigated.The incinerated ash of sewage sludge was mixed with sodium hydroxide or sodium carbonate,and treated at 750 ℃ ...The phosphorus recovery from incinerated ash of sewage sludge by a heat treatment method was investigated.The incinerated ash of sewage sludge was mixed with sodium hydroxide or sodium carbonate,and treated at 750 ℃ to 900 ℃ in aerobic conditions.The phosphorus was successfully recovered as an alkali metal phosphate from the treated ash through water extraction.The recovery rate of the phosphorus reached about 74% to 78%.The optimal condition of the phosphorus recovery and composition of the recovered phosphorus was investigated.展开更多
Health-care waste contains potentially harmful microorganisms and compounds which can infect and affect hospital patients, healthcare workers, the general public and environment. Therefore, management of health care w...Health-care waste contains potentially harmful microorganisms and compounds which can infect and affect hospital patients, healthcare workers, the general public and environment. Therefore, management of health care waste requires safe handling, treatment and disposal procedures. While incineration reduces the volume and quantity of waste for final disposal, it leads to the production of fly and bottom ashes laden with toxic incomplete combustion products such as Polycyclic Aromatic Hydrocarbons (PAHs), dioxins, furans and heavy metals. This exposes workers who handle and dispose the bottom ashes, hospital patients, the general public and environment. The goal of this study was to determine the total and individual levels of 16 most prevalent and toxic PAHs. Bottom ash samples were collected from incinerators in five county hospitals in Kenya, namely;Moi-Voi, Narok, Kitale, Makindu and Isiolo. Bottom ash samples were collected over a period of six months from the five hospitals. The samples were then sieved, homogenised and stored at 4°C in amber coloured glass containers. The PAHs were extracted using 30 ml of a hexane-acetone solvent (1:1) mixture by ultrasonication at room temperature (23°C) for 45 minutes. The PAHs were then analyzed with a GC-MS spectrophotometer model (Shimadzu GCMS-QP2010 SE) connected to a computer work station was used for the PAHs analysis. The GC-MS was equipped with an SGE BPX5 GC capillary column (30 m × 0.25 mm × 0.25 μm) for the separation of compounds. Helium was used as the carrier gas at a flow rate of 15.5 ml/minute and 14.5 psi. 1 μl of the sample was injected at 280°C, split mode (10:1). The oven programming was set for a total runtime of 40 minutes, which included: 100°C (2-minute hold);10°C /min rise to 200°C;7°C /min rise to 249°C;3°C /min rise to 300°C (2-minute hold). The interface temperature was set at 290°C. Analysis was done in Selected Ion Monitoring (SIM) mode and the peak areas of each of the PAHs were collected from the chromatograph and used for quantification of the 16 PAHs listed by the U.S. Environmental Protection Agency (EPA) which included, BaA (benz[a]anthracene: 4 rings), BaP (benzo[a]pyrene: 5 rings), BbF (benzo [b]fluoranthene: 5 rings), BkF (benzo[k]fluoranthene: 5 rings), Chr (chrysene: 4 rings), DbA (dibenz[a,h]anthracene: 5 rings), InP (indeno[1,2,3 - cd] pyrene: 6 rings) and Acp (acenaphthene: 3 rings), Acpy (acenaphthylene: 3 rings), Ant (anthracene: 3 rings), BghiP (benzo[g,h,i]perylene: 6 rings), Flu (fluorene: 3 rings), FluA (fluoranthene: 4 rings), Nap (naphthalene: 2 rings), PhA (phenanthrene: 3 rings) and Pyr (pyrene: 4 rings). Ion source-interface temperature was set at 200°C - 250°C. Internal standards from Sigma Aldrich were used in the analysis and the acquired mass spectra data were then matched against the NIST 2014 library [1] [2]. The mean PAHs concentration in the bottom ashes of each hospital varied broadly from 0.001 mg/kg to 0.4845 mg/kg, and the mean total concentration levels of individual PAHs ranged from 0.0072 mg/kg to 1.171 mg/kg. Low molecular weight PAHs (Phenanthrene, Naphthalene and Fluorene) were predominant in all the hospital wastes whereas Kitale and Narok presented the lowest PAHs concentrations and the lowest number of individual PAHs. Moi/Voi recorded the highest total PAHs concentration at 1.3129 ± 0.0023 mg/kg from a total of 11 PAHs being detected from the bottom ash samples. Narok had only three PAHs being detected at very low concentrations of 0.0041 ± 0.00 mg/kg, 0.0076 ± 0.00 mg/kg and 0.012 ± 0.00 mg/kg for phenanthrene, anthracene and chrysene respectively. This study presents hospital incinerator bottom ash as containing detectable levels of both carcinogenic and non-carcinogenic PAHs. Continued unprotected exposure of hospital workers (waste handlers) to the bottom ash PAHs could be hazardous to their health because of their cumulative effect. Preventive measures e.g. the use of Personal protective equipment (PPE) should be prioritised to minimise direct contact with the bottom ash. The study recommends an upgrade on incinerator technology for efficient combustion processes thus for better pollution control.展开更多
Healthcare wastes contain potentially harmful microorganisms, inorganic and organic compounds that pose a risk to human health and the environment. Incineration is a common method employed in healthcare waste manageme...Healthcare wastes contain potentially harmful microorganisms, inorganic and organic compounds that pose a risk to human health and the environment. Incineration is a common method employed in healthcare waste management to reduce volume, quantity, toxicity as well as elimination of microorganisms. However, some of the substances remain unchanged during incineration and become part of bottom ash, such as heavy metals and persistent organic pollutants. Monitoring of pollution by heavy metals is important since their concentrations in the environment affect public health. The goal of this study was to determine the levels of Copper (Cu), Zinc (Zn) Lead (Pb), Cadmium (Cd) and Nickel (Ni) in the incinerator bottom ash in five selected County hospitals in Kenya. Bottom ash samples were collected over a period of six months. Sample preparation and treatment were done using standard methods. Analysis of the heavy metals were done using atomic absorption spectrophotometer, model AA-6200. One-Way Analysis of Variance (ANOVA) was performed to determine whether there were significant differences on the mean levels of Cu, Zn, Pd, Cd and Ni in incinerator bottom ash from the five sampling locations. A post-hoc Tukey’s Test (HSD) was used to determine if there were significant differences between and within samples. The significant differences were accepted at p ≤ 0.05. To standardize the results, overall mean of each metal from each site was calculated. The metal mean concentration values were compared with existing permissible levels set by the WHO. The concentrations (mg/kg) were in the range of 102.27 - 192.53 for Cu, Zn (131.68 - 2840.85), Pb (41.06 - 303.96), Cd (1.92 - 20.49) whereas Ni was (13.83 - 38.27) with a mean of 150.76 ± 77.88 for Copper, 131.66 ± 1598.95 for Zinc, 234.60 ± 262.76 for Lead, 12.256 ± 10.86 for Cadmium and 29.45 ± 18.24 for Nickel across the five sampling locations. There were significant differences between levels determined by one-way ANOVA of Zn (F (4, 25) = 6.893, p = 0.001, p ≤ 0.05) and Cd (F (4, 25) = 5.641, p = 0.02) and none with Cu (F (4, 25) = 1.405, p = 0.261, p ≤ 0.05), Pb (F (4, 25) = 1.073, p = 0.391, p ≤ 0.05) and Ni (F (4, 25) = 2.492, p = 0.069). Results reveal that metal content in all samples exceed the WHO permissible levels for Cu (100 mg/kg), while those for Ni were below the WHO set standards of 50 mg/kg. Levels of Zn in three hospitals exceeded permissible level of 300 mg/kg while level of Pb exceeded WHO set standards of 100 mg/kg in two hospitals. Samples from four hospitals exceeded permissible level for Cd of 3 mg/kg. This study provides evidence that incinerator bottom ash is contaminated with toxic heavy metals to human health and the environment. This study recommends that hospitals should handle the bottom ash as hazardous wastes and there is need to train and provide appropriate personal protective equipment to healthcare workers, waste handlers, and incinerator operators and enforce compliance to existing regulation and guidelines on healthcare waste management to safeguard the environment and human health.展开更多
In the municipal solid waste incineration process,it is difficult to effectively control the gas oxygen content by setting the air flow according to artificial experience.To address this problem,this paper proposes an...In the municipal solid waste incineration process,it is difficult to effectively control the gas oxygen content by setting the air flow according to artificial experience.To address this problem,this paper proposes an optimization control method of gas oxygen content based on model predictive control.First,a stochastic configuration network is utilized to establish a prediction model of gas oxygen content.Second,an improved differential evolution algorithm that is based on parameter adaptive and t-distribution strategy is employed to address the set value of air flow.Finally,model predictive control is combined with the event triggering strategy to reduce the amount of computation and the controller's frequent actions.The experimental results show that the optimization control method proposed in this paper obtains a smaller degree of fluctuation in the air flow set value,which can ensure the tracking control performance of the gas oxygen content while reducing the amount of calculation.展开更多
Phosphorus(P)recovery from incinerated sewage sludge ash(ISSA)has been extensively investigated,but insufficient research has been conducted to evaluate the effect of different kinds of recovered phosphate fertilizers...Phosphorus(P)recovery from incinerated sewage sludge ash(ISSA)has been extensively investigated,but insufficient research has been conducted to evaluate the effect of different kinds of recovered phosphate fertilizers(RPFs)on plant growth with respect to the P and heavy metal contents of RPFs.In this study,three kinds of RPFs,precipitated calcium phosphate fertilizer(CaP),struvite phosphate fertilizer(SP),and P-loaded biochar(BP),produced from ISSA were characterized,and their agronomic effectiveness was verified by hydroponic and soil cultivation.In addition to the three kinds of RPFs,a control group(mono-phosphate fertilizer in hydroponic group/compound fertilizer in soil cultivation group)and a blank control group(BC,with zero P)were tested on choy sum and ryegrass at the same time.SP has the highest P purity(76.0%of struvite)while the BP has the most complex P species(P was co-exist with Fe,Al,and Mg).Plant growth results showed that the RPFs greatly facilitated plant growth and demonstrated superior/comparable effects to those of control group.In hydroponics testing,SP showed the best effect(shoot length of 17.0 cm,chlorophyll content of 2.05 mg/g)due to the Mg involved and the high P purity of SP,while BP performed the best(shoot length of 13.7 cm,chlorophyll content of 2.42 mg/g)in the soil testing system among all of the groups because of the additional nutritional elements and the high P availability of BP.Additionally,the accumulation of heavy metals in the plants under all conditions did not exceed the limits stipulated in the regulations.These results indicate that recovering P from ISSA is an attractive technology to produce P fertilizers,which can alleviate both the scarcity of phosphate resources and the burden of ISSA management.展开更多
In a thorium-based molten salt reactor(TMSR),it is difficult to achieve the pure 232Th–^(233)U fuel cycle without sufficient^(233)U fuel supply.Therefore,the original molten salt reactor was designed to use enriched ...In a thorium-based molten salt reactor(TMSR),it is difficult to achieve the pure 232Th–^(233)U fuel cycle without sufficient^(233)U fuel supply.Therefore,the original molten salt reactor was designed to use enriched uranium or plutonium as the starting fuel.By exploiting plutonium as the starting fuel and thorium as the fertile fuel,the high-purity^(233)U produced can be separated from the spent fuel by fluorination volatilization.Therefore,the molten salt reactor started with plutonium can be designed as a^(233)U breeder with the burning plutonium extracted from a pressurized water reactor(PWR).Combining these advantages,the study of the physical properties of plutonium-activated salt reactors is attractive.This study mainly focused on the burnup performance and temperature reactivity coefficient of a small modular molten-salt reactor started with plutonium(SM-MSR-Pu).The neutron spectra,^(233)U production,plutonium incineration,minor actinide(MA)residues,and temperature reactivity coefficients for different fuel salt volume fractions(VF)and hexagon pitch(P)sizes were calculated to analyze the burnup behavior in the SM-SMR-Pu.Based on the comparative analysis results of the burn-up calculation,a lower VF and larger P size are more beneficial for improving the burnup performance.However,from a passive safety perspective,a higher fuel volume fraction and smaller hexagon pitch size are necessary to achieve a deep negative feedback coefficient.Therefore,an excellent burnup performance and a deep negative temperature feedback coefficient are incompatible,and the optimal design range is relatively narrow in the optimized design of an SM-MSR-Pu.In a comprehensive consideration,P=20 cm and VF=20%are considered to be relatively balanced design parameters.Based on the fuel off-line batching scheme,a 250 MWth SM-MSR-Pu can produce approximately 29.83 kg of ^(233)U,incinerate 98.29 kg of plutonium,and accumulate 14.70 kg of MAs per year,and the temperature reactivity coefficient can always be lower than−4.0pcm/K.展开更多
Air pollution control poses a major problem in the implementation of municipal solid waste incineration(MSWI).Accurate prediction of nitrogen oxides(NO_(x))concentration plays an important role in efficient NO_(x)emis...Air pollution control poses a major problem in the implementation of municipal solid waste incineration(MSWI).Accurate prediction of nitrogen oxides(NO_(x))concentration plays an important role in efficient NO_(x)emission controlling.In this study,a modular long short-term memory(M-LSTM)network is developed to design an efficient prediction model for NO_(x)concentration.First,the fuzzy C means(FCM)algorithm is utilized to divide the task into several sub-tasks,aiming to realize the divide-and-conquer ability for complex task.Second,long short-term memory(LSTM)neural networks are applied to tackle corresponding sub-tasks,which can improve the prediction accuracy of the sub-networks.Third,a cooperative decision strategy is designed to guarantee the generalization performance during the testing or application stage.Finally,after being evaluated by a benchmark simulation,the proposed method is applied to a real MSWI process.And the experimental results demonstrate the considerable prediction ability of the M-LSTM network.展开更多
Domestic waste incineration slag(WIS)includes fly ash and slag.Fly ash is classified as hazardous waste because it contains heavy metals.Most of slag are directly stacked or landfilled due to problems such as large ou...Domestic waste incineration slag(WIS)includes fly ash and slag.Fly ash is classified as hazardous waste because it contains heavy metals.Most of slag are directly stacked or landfilled due to problems such as large output and low utilization rate.Harmless treatment is imminent.If WIS is used effectively in the road engineering,which can realize the high-quality and high-efficiency recycling of WIS,and it is of great significance to save resources and protect the environment.This study applies a geopolymer prepared from WIS fly ash as a stabilizing agent in WIS blending macadam for use as a pavement base mixture,and reports the mechanical properties(unconfined compressive strength,splitting strength,and resilience modulus)of the geopolymer-stabilized WIS blending macadam(GeoWIS).The leaching concentrations of harmful heavy metals of GeoWIS soaked in water were also investigated.Finally,the strength formation and heavy metal stability mechanisms were explored.The unconfined compressive strength,splitting strength,and compressive resilient modulus of GeoWIS all increased with increasing geopolymer content and decreasing WIS content.The strength of GeoWIS was derived from its geopolymerization and hydration products(C-S-H gel,N-A-S-H gel,and AFt).When the geopolymer content reached 12%–14%,the GeoWIS without natural macadam met the strength criterion of the asphalt pavement base.Through physical adsorption and chemical bonding,the geopolymer significantly reduced the leaching of harmful heavy metals.In GeoWIS with 50%WIS and stabilized with 10%geopolymer,the Cr,Ni,Cd,and Pb concentrations met the grade III groundwater standard.Concentrations of heavy metals leached from GeoWIS are low and exert little impact on environment.展开更多
The destruction of concrete building materials in severely cold regions of the north is more severely affected by freeze-thaw cycles,and the relationship between the mechanical properties and pore structure of concret...The destruction of concrete building materials in severely cold regions of the north is more severely affected by freeze-thaw cycles,and the relationship between the mechanical properties and pore structure of concrete with fine aggregate from municipal solid waste(MSW)incineration bottom ash after freeze-thaw cycles is analyzed under the degree of freeze-thaw hazard variation.In this paper,the gray correlation method is used to calculate the correlation between the relative dynamic elastic modulus,compressive strength,and microscopic porosity parameters to speculate on the most important factors affecting their changes.The GM(1,1)model was established based on the compressive strength of the waste incineration ash aggregate concrete,the relative error between the simulated and actual values in the model was less than 5%,and the accuracy of the model was level 1,indicating that the GM(1,1)model can well reflect the change in the compressive strength of the MSW incineration bottom ash aggregate concrete during freeze-thaw cycles.Using the gray correlation method,the correlation between the relative dynamic elastic modulus,compressive strength,air content,specific surface area,pore spacing coefficient,and pore average chord length was calculated,and the pore spacing coefficient and pore average chord length were determined to be highly correlated with each other.This determination can help analyze and infer the deterioration mechanism of concrete subject to freeze-thaw cycles.These results can provide a theoretical basis for guiding the engineering practice of concrete with fine aggregates of household bottom ash in the northern cold region.展开更多
Garbage incineration is an ideal method for the harmless and resource-oriented treatment of urban domestic waste.However,current domestic waste incineration power plants often face challenges related to maintaining co...Garbage incineration is an ideal method for the harmless and resource-oriented treatment of urban domestic waste.However,current domestic waste incineration power plants often face challenges related to maintaining consistent steam production and high operational costs.This article capitalizes on the technical advantages of big data artificial intelligence,optimizing the power generation process of domestic waste incineration as the entry point,and adopts four main engine modules of Alibaba Cloud reinforcement learning algorithm engine,operating parameter prediction engine,anomaly recognition engine,and video visual recognition algorithm engine.The reinforcement learning algorithm extracts the operational parameters of each incinerator to obtain a control benchmark.Through the operating parameter prediction algorithm,prediction models for drum pressure,primary steam flow,NOx,SO2,and HCl are constructed to achieve short-term prediction of operational parameters,ultimately improving control performance.The anomaly recognition algorithm develops a thickness identification model for the material layer in the drying section,allowing for rapid and effective assessment of feed material thickness to ensure uniformity control.Meanwhile,the visual recognition algorithm identifies flame images and assesses the combustion status and location of the combustion fire line within the furnace.This real-time understanding of furnace flame combustion conditions guides adjustments to the grate and air volume.Integrating AI technology into the waste incineration sector empowers the environmental protection industry with the potential to leverage big data.This development holds practical significance in optimizing the harmless and resource-oriented treatment of urban domestic waste,reducing operational costs,and increasing efficiency.展开更多
The phosphorus recovery from the incinerated ash using NaOH by the heat treatment,was investigated.In this method,non-reacted NaOH containing alkali water was generated with the phosphorus recovery.In order to find ou...The phosphorus recovery from the incinerated ash using NaOH by the heat treatment,was investigated.In this method,non-reacted NaOH containing alkali water was generated with the phosphorus recovery.In order to find out the best method for reuse of the alkali water,the alkali water was mixed with new reagent of NaOH,and the phosphorus recovery was carried out.The phosphorus was recovered as a sodium phosphate,and the recovery rate was almost the same even with the reuse of the alkali water.展开更多
The impact of moisture on the partitioning of the heavy metals including Pb,Zn,Cu and Cd in municipal solid waste (MSW) was studied in a laboratory tubular furnace.A thermodynamic investigation using CHEMKIN softwar...The impact of moisture on the partitioning of the heavy metals including Pb,Zn,Cu and Cd in municipal solid waste (MSW) was studied in a laboratory tubular furnace.A thermodynamic investigation using CHEMKIN software was performed to compare the experimental results.Simulated waste,representative of typical MSW with and without chlorine compounds,was burned at the background temperature of 700 and 950°C,respectively.In the absence of chlorine,the moisture content has no evident effect on the volatility of Pb,Zn and Cu at either 700 or 950°C,however,as flue gas moisture increasing the Cd distribution in the bottom ash increased at 700°C and reduced at 950°C,respectively.In the presence of chlorine,the flue gas moisture reduced the volatility of Pb,Zn and Cu due to the transformation of the more volatile metal chlorides into less volatile metal oxides,and the reduction became significant as chlorine content increase.For Cd,the chlorine promotes its volatility through the formation of more volatile CdCl 2.As a result,the increased moisture content increases the Pb,Zn,Cu and Cd concentrations in the bottom ash,which limits the utilization of the bottom ash as a construction material.Therefore,in order to accumulate heavy metals into the fly ash,MSW should be dried before incineration.展开更多
Basic properties of fly ash samples from different urban waste combustion facilities in China were analyzed using as X-ray fluorescence (XRF), scanning electron microscopy (SEM), X-ray diffraction (XRD). The lea...Basic properties of fly ash samples from different urban waste combustion facilities in China were analyzed using as X-ray fluorescence (XRF), scanning electron microscopy (SEM), X-ray diffraction (XRD). The leaching toxicity procedure and some factors influencing heavy metals distribution in fly ash were further investigated. Experimental results indicate that the fly ash structures are complex and its properties are variable. The results of XRF and SEM revealed that the major elements (〉10000 mg/kg, listed in decreasing order of abundance) in fly ash are O, Ca, Cl, Si, S, K, Na, Al, Fe and Zn. These elements account for 93% to 97%, and the content of Cl ranges from 6.93% to 29.18 %, while that of SiO2 does from 4.48% to 24.84%. The minor elements (1000 to 10000 mg/kg) include Cr, Cu and Pb. Primary heavy metals in fly ash include Zn, Pb, Cr, Cu etc. According to standard leaching test, heavy metal leaching levels vary from 0 to 163.10 mg/L (Pb) and from 0.049 to 164.90 mg/L (Zn), mostly exceeding the Chinese Identification Standard for hazardous wastes. Morphology of fly ash is irregular, with both amorphous structures and polycrystalline aggregates. Further research showed that heavy metals were volatilized at a high furnace temperature, condensed when cooling down during the post-furnace system and captured at air pollution control systems. Generally, heavy metals are mainly present in the forms of aerosol particulates or tiny particulates enriched on surfaces of fly ash particles. The properties of fly ash are greatly influenced by the treatment capacities of incinerators or the variation of waste retention time in chamber. Fly ash from combustors of larger capacities generally has higher contents of volatile component and higher leaching toxicity, while those of smaller capacities often produce fly ash containing higher levels of nonvolatile components and has lower toxicity. The content of heavy metals and leaching toxicity maybe have no convincing correlation, and high alkali content of CaO greatly contribute to leaching toxicity of heavy metal and acid neutralization capacity against acid rain.展开更多
At present,all kinds of municipal solid waste incineration (MSWI) fly ash stabilization technology has been reported and successfully applied in many countries.However,leaching procedures are very different that the t...At present,all kinds of municipal solid waste incineration (MSWI) fly ash stabilization technology has been reported and successfully applied in many countries.However,leaching procedures are very different that the technologies lack uniform standard,and it is even impossible to predict the long-term stabilization.Geochemical model can explain the environmental stabilization based on chemical phase and thermodynamic crystal structure,and it is also able to guide the development of environment-friendly stabi...展开更多
Great differences between municipal solid wastes (MSW) produced at different places and different times in terms of such parameters as physical ingredient and heating value lead to difficulty in effective handling of ...Great differences between municipal solid wastes (MSW) produced at different places and different times in terms of such parameters as physical ingredient and heating value lead to difficulty in effective handling of MSW. In this paper, ingredient, heating value and their temporal varying trends of typical MSW in Beijing were continuously measured and analyzed. With consideration of the process in pyrolysis and incineration, correlation between physical ingredients and heating values was induced, favorable for evaluation of heating value needed in handling of MSW from simple analysis of physical ingredients of it.展开更多
基金The authors would like to thank the financial support of National Natural Science Foundation of China(Grant Nos.51861165104 and 51625903)National Key Research and Development Project(Grant No.2019YFC1804002).
文摘Management of incinerated sewage sludge ash(ISSA)and dredged contaminated marine sediments(CMSs)is a great challenge for Hong Kong and other coastal cities due to limited landfilling capacity.The present study investigates the use of high content(20%of sediment by mass)of ISSA in combination with cement/lime for solidification/stabilization(S/S)treatment of CMSs to provide a way to reuse the wastes as construction materials.The results showed that ISSA being a porous material was able to absorb a large amount of water rendering a more efficient solidification process of the marine sediment which normally had a very high water content(w80%).The S/S treatment improved the engineering properties of the sediment,but reduced the workability,especially for the lime-treated samples.Lime can be used to replace ordinary Portland cement(OPC)for better heavy metal immobilization and carbon emission reduction.The hardened sediment samples prepared with 10%of lime and 20%of ISSA could attain a strength of 1.6 MPa after 28 d of curing.In addition,leaching tests confirmed that there was no environmental risk induced by these stabilized materials.The formation of hydrated cementitious compounds including calcium silicate hydrate(CeSeH)/calcium aluminate silicate hydrate(C-A-S-H)/hydrocalumite/calcite was mainly responsible for the strength development in the ISSA/lime-treated sediments.
基金The authors wish to express their appreciation to Dr.Eric Bray(Professor of Yokkaichi University)for his advice on making the article.The authors also express their appreciation to the Hinaga Wastewater Treatment Center(Yokkaichi City Government,Waterworks and Sewage Bureau)offering us the ash.
文摘The compounds of aluminum phosphate are used to remove the fluorine compounds from wastewater. The fluorine removal agent using the ash of sewage sludge and the municipal waste in addition to sulfuric acid were investigated. The removal agent showed high removal performance, and the fluorine concentration of the treated water reached below 0.1 mg/L, and the noticeable elution of the harmful metals from the ashes were not found in this experiment.
文摘Calcium-based compounds are used as fluorine removal treatment materials in water.However,due to the water solubility of calcium fluoride,there is a problem with low fluorine removal performance.For this reason,various removing agents including phosphorus have been developed.We have found that a combination of aluminum phosphate recovered from incinerated ash of the sewage sludge and refuse incineration ash has a high fluorine removal performance.At the highest removal performance,F ion concentration of the treated water reached 0.1 mg/L,so an optimal formulation method was investigated.
文摘The phosphorus recovery from incinerated ash of sewage sludge by a heat treatment method was investigated.The incinerated ash of sewage sludge was mixed with sodium hydroxide or sodium carbonate,and treated at 750 ℃ to 900 ℃ in aerobic conditions.The phosphorus was successfully recovered as an alkali metal phosphate from the treated ash through water extraction.The recovery rate of the phosphorus reached about 74% to 78%.The optimal condition of the phosphorus recovery and composition of the recovered phosphorus was investigated.
文摘Health-care waste contains potentially harmful microorganisms and compounds which can infect and affect hospital patients, healthcare workers, the general public and environment. Therefore, management of health care waste requires safe handling, treatment and disposal procedures. While incineration reduces the volume and quantity of waste for final disposal, it leads to the production of fly and bottom ashes laden with toxic incomplete combustion products such as Polycyclic Aromatic Hydrocarbons (PAHs), dioxins, furans and heavy metals. This exposes workers who handle and dispose the bottom ashes, hospital patients, the general public and environment. The goal of this study was to determine the total and individual levels of 16 most prevalent and toxic PAHs. Bottom ash samples were collected from incinerators in five county hospitals in Kenya, namely;Moi-Voi, Narok, Kitale, Makindu and Isiolo. Bottom ash samples were collected over a period of six months from the five hospitals. The samples were then sieved, homogenised and stored at 4°C in amber coloured glass containers. The PAHs were extracted using 30 ml of a hexane-acetone solvent (1:1) mixture by ultrasonication at room temperature (23°C) for 45 minutes. The PAHs were then analyzed with a GC-MS spectrophotometer model (Shimadzu GCMS-QP2010 SE) connected to a computer work station was used for the PAHs analysis. The GC-MS was equipped with an SGE BPX5 GC capillary column (30 m × 0.25 mm × 0.25 μm) for the separation of compounds. Helium was used as the carrier gas at a flow rate of 15.5 ml/minute and 14.5 psi. 1 μl of the sample was injected at 280°C, split mode (10:1). The oven programming was set for a total runtime of 40 minutes, which included: 100°C (2-minute hold);10°C /min rise to 200°C;7°C /min rise to 249°C;3°C /min rise to 300°C (2-minute hold). The interface temperature was set at 290°C. Analysis was done in Selected Ion Monitoring (SIM) mode and the peak areas of each of the PAHs were collected from the chromatograph and used for quantification of the 16 PAHs listed by the U.S. Environmental Protection Agency (EPA) which included, BaA (benz[a]anthracene: 4 rings), BaP (benzo[a]pyrene: 5 rings), BbF (benzo [b]fluoranthene: 5 rings), BkF (benzo[k]fluoranthene: 5 rings), Chr (chrysene: 4 rings), DbA (dibenz[a,h]anthracene: 5 rings), InP (indeno[1,2,3 - cd] pyrene: 6 rings) and Acp (acenaphthene: 3 rings), Acpy (acenaphthylene: 3 rings), Ant (anthracene: 3 rings), BghiP (benzo[g,h,i]perylene: 6 rings), Flu (fluorene: 3 rings), FluA (fluoranthene: 4 rings), Nap (naphthalene: 2 rings), PhA (phenanthrene: 3 rings) and Pyr (pyrene: 4 rings). Ion source-interface temperature was set at 200°C - 250°C. Internal standards from Sigma Aldrich were used in the analysis and the acquired mass spectra data were then matched against the NIST 2014 library [1] [2]. The mean PAHs concentration in the bottom ashes of each hospital varied broadly from 0.001 mg/kg to 0.4845 mg/kg, and the mean total concentration levels of individual PAHs ranged from 0.0072 mg/kg to 1.171 mg/kg. Low molecular weight PAHs (Phenanthrene, Naphthalene and Fluorene) were predominant in all the hospital wastes whereas Kitale and Narok presented the lowest PAHs concentrations and the lowest number of individual PAHs. Moi/Voi recorded the highest total PAHs concentration at 1.3129 ± 0.0023 mg/kg from a total of 11 PAHs being detected from the bottom ash samples. Narok had only three PAHs being detected at very low concentrations of 0.0041 ± 0.00 mg/kg, 0.0076 ± 0.00 mg/kg and 0.012 ± 0.00 mg/kg for phenanthrene, anthracene and chrysene respectively. This study presents hospital incinerator bottom ash as containing detectable levels of both carcinogenic and non-carcinogenic PAHs. Continued unprotected exposure of hospital workers (waste handlers) to the bottom ash PAHs could be hazardous to their health because of their cumulative effect. Preventive measures e.g. the use of Personal protective equipment (PPE) should be prioritised to minimise direct contact with the bottom ash. The study recommends an upgrade on incinerator technology for efficient combustion processes thus for better pollution control.
文摘Healthcare wastes contain potentially harmful microorganisms, inorganic and organic compounds that pose a risk to human health and the environment. Incineration is a common method employed in healthcare waste management to reduce volume, quantity, toxicity as well as elimination of microorganisms. However, some of the substances remain unchanged during incineration and become part of bottom ash, such as heavy metals and persistent organic pollutants. Monitoring of pollution by heavy metals is important since their concentrations in the environment affect public health. The goal of this study was to determine the levels of Copper (Cu), Zinc (Zn) Lead (Pb), Cadmium (Cd) and Nickel (Ni) in the incinerator bottom ash in five selected County hospitals in Kenya. Bottom ash samples were collected over a period of six months. Sample preparation and treatment were done using standard methods. Analysis of the heavy metals were done using atomic absorption spectrophotometer, model AA-6200. One-Way Analysis of Variance (ANOVA) was performed to determine whether there were significant differences on the mean levels of Cu, Zn, Pd, Cd and Ni in incinerator bottom ash from the five sampling locations. A post-hoc Tukey’s Test (HSD) was used to determine if there were significant differences between and within samples. The significant differences were accepted at p ≤ 0.05. To standardize the results, overall mean of each metal from each site was calculated. The metal mean concentration values were compared with existing permissible levels set by the WHO. The concentrations (mg/kg) were in the range of 102.27 - 192.53 for Cu, Zn (131.68 - 2840.85), Pb (41.06 - 303.96), Cd (1.92 - 20.49) whereas Ni was (13.83 - 38.27) with a mean of 150.76 ± 77.88 for Copper, 131.66 ± 1598.95 for Zinc, 234.60 ± 262.76 for Lead, 12.256 ± 10.86 for Cadmium and 29.45 ± 18.24 for Nickel across the five sampling locations. There were significant differences between levels determined by one-way ANOVA of Zn (F (4, 25) = 6.893, p = 0.001, p ≤ 0.05) and Cd (F (4, 25) = 5.641, p = 0.02) and none with Cu (F (4, 25) = 1.405, p = 0.261, p ≤ 0.05), Pb (F (4, 25) = 1.073, p = 0.391, p ≤ 0.05) and Ni (F (4, 25) = 2.492, p = 0.069). Results reveal that metal content in all samples exceed the WHO permissible levels for Cu (100 mg/kg), while those for Ni were below the WHO set standards of 50 mg/kg. Levels of Zn in three hospitals exceeded permissible level of 300 mg/kg while level of Pb exceeded WHO set standards of 100 mg/kg in two hospitals. Samples from four hospitals exceeded permissible level for Cd of 3 mg/kg. This study provides evidence that incinerator bottom ash is contaminated with toxic heavy metals to human health and the environment. This study recommends that hospitals should handle the bottom ash as hazardous wastes and there is need to train and provide appropriate personal protective equipment to healthcare workers, waste handlers, and incinerator operators and enforce compliance to existing regulation and guidelines on healthcare waste management to safeguard the environment and human health.
基金supported by the National Natural Science Foundation of China(62373017,62073006)and the Beijing Natural Science Foundation of China(4212032)。
文摘In the municipal solid waste incineration process,it is difficult to effectively control the gas oxygen content by setting the air flow according to artificial experience.To address this problem,this paper proposes an optimization control method of gas oxygen content based on model predictive control.First,a stochastic configuration network is utilized to establish a prediction model of gas oxygen content.Second,an improved differential evolution algorithm that is based on parameter adaptive and t-distribution strategy is employed to address the set value of air flow.Finally,model predictive control is combined with the event triggering strategy to reduce the amount of computation and the controller's frequent actions.The experimental results show that the optimization control method proposed in this paper obtains a smaller degree of fluctuation in the air flow set value,which can ensure the tracking control performance of the gas oxygen content while reducing the amount of calculation.
基金support from Major Scientific and Technological Innovation Projects of Shandong Province(No.2021CXGC011201)the start-up funding for the new introduced talents of the Beijing Normal University(No.28707-111032107)Hong Kong Research Grants Council(PolyU No.152132/14E)for financial support.
文摘Phosphorus(P)recovery from incinerated sewage sludge ash(ISSA)has been extensively investigated,but insufficient research has been conducted to evaluate the effect of different kinds of recovered phosphate fertilizers(RPFs)on plant growth with respect to the P and heavy metal contents of RPFs.In this study,three kinds of RPFs,precipitated calcium phosphate fertilizer(CaP),struvite phosphate fertilizer(SP),and P-loaded biochar(BP),produced from ISSA were characterized,and their agronomic effectiveness was verified by hydroponic and soil cultivation.In addition to the three kinds of RPFs,a control group(mono-phosphate fertilizer in hydroponic group/compound fertilizer in soil cultivation group)and a blank control group(BC,with zero P)were tested on choy sum and ryegrass at the same time.SP has the highest P purity(76.0%of struvite)while the BP has the most complex P species(P was co-exist with Fe,Al,and Mg).Plant growth results showed that the RPFs greatly facilitated plant growth and demonstrated superior/comparable effects to those of control group.In hydroponics testing,SP showed the best effect(shoot length of 17.0 cm,chlorophyll content of 2.05 mg/g)due to the Mg involved and the high P purity of SP,while BP performed the best(shoot length of 13.7 cm,chlorophyll content of 2.42 mg/g)in the soil testing system among all of the groups because of the additional nutritional elements and the high P availability of BP.Additionally,the accumulation of heavy metals in the plants under all conditions did not exceed the limits stipulated in the regulations.These results indicate that recovering P from ISSA is an attractive technology to produce P fertilizers,which can alleviate both the scarcity of phosphate resources and the burden of ISSA management.
基金supported by the Chinese TMSR Strategic Pioneer Science and Technology Project(No.XDA02010000)Shanghai Pilot Program for Basic Research-Chinese Academy of Science,Shanghai Branch(No.JCYJ-SHFY-2021-003)the Chinese Academy of Sciences Special Research Assistant Funding Project.
文摘In a thorium-based molten salt reactor(TMSR),it is difficult to achieve the pure 232Th–^(233)U fuel cycle without sufficient^(233)U fuel supply.Therefore,the original molten salt reactor was designed to use enriched uranium or plutonium as the starting fuel.By exploiting plutonium as the starting fuel and thorium as the fertile fuel,the high-purity^(233)U produced can be separated from the spent fuel by fluorination volatilization.Therefore,the molten salt reactor started with plutonium can be designed as a^(233)U breeder with the burning plutonium extracted from a pressurized water reactor(PWR).Combining these advantages,the study of the physical properties of plutonium-activated salt reactors is attractive.This study mainly focused on the burnup performance and temperature reactivity coefficient of a small modular molten-salt reactor started with plutonium(SM-MSR-Pu).The neutron spectra,^(233)U production,plutonium incineration,minor actinide(MA)residues,and temperature reactivity coefficients for different fuel salt volume fractions(VF)and hexagon pitch(P)sizes were calculated to analyze the burnup behavior in the SM-SMR-Pu.Based on the comparative analysis results of the burn-up calculation,a lower VF and larger P size are more beneficial for improving the burnup performance.However,from a passive safety perspective,a higher fuel volume fraction and smaller hexagon pitch size are necessary to achieve a deep negative feedback coefficient.Therefore,an excellent burnup performance and a deep negative temperature feedback coefficient are incompatible,and the optimal design range is relatively narrow in the optimized design of an SM-MSR-Pu.In a comprehensive consideration,P=20 cm and VF=20%are considered to be relatively balanced design parameters.Based on the fuel off-line batching scheme,a 250 MWth SM-MSR-Pu can produce approximately 29.83 kg of ^(233)U,incinerate 98.29 kg of plutonium,and accumulate 14.70 kg of MAs per year,and the temperature reactivity coefficient can always be lower than−4.0pcm/K.
基金the financial support from the National Natural Science Foundation of China(62021003,61890930-5,61903012,62073006)Beijing Natural Science Foundation(42130232)the National Key Research and Development Program of China(2021ZD0112301,2021ZD0112302)。
文摘Air pollution control poses a major problem in the implementation of municipal solid waste incineration(MSWI).Accurate prediction of nitrogen oxides(NO_(x))concentration plays an important role in efficient NO_(x)emission controlling.In this study,a modular long short-term memory(M-LSTM)network is developed to design an efficient prediction model for NO_(x)concentration.First,the fuzzy C means(FCM)algorithm is utilized to divide the task into several sub-tasks,aiming to realize the divide-and-conquer ability for complex task.Second,long short-term memory(LSTM)neural networks are applied to tackle corresponding sub-tasks,which can improve the prediction accuracy of the sub-networks.Third,a cooperative decision strategy is designed to guarantee the generalization performance during the testing or application stage.Finally,after being evaluated by a benchmark simulation,the proposed method is applied to a real MSWI process.And the experimental results demonstrate the considerable prediction ability of the M-LSTM network.
基金This work was supported by the Fundamental Research Funds for the Central Universities,CHD(grant number 300102212906)the Key R&D Plan of Shaanxi Province(grant number 2023-YBSF-390)+1 种基金the Innovation Capability Support Program of Shaanxi(grant number 2022TD-07)the Xianyang City,Shaanxi Province,China 2019 Key Research and Development Program(grant number 2019k02-125).
文摘Domestic waste incineration slag(WIS)includes fly ash and slag.Fly ash is classified as hazardous waste because it contains heavy metals.Most of slag are directly stacked or landfilled due to problems such as large output and low utilization rate.Harmless treatment is imminent.If WIS is used effectively in the road engineering,which can realize the high-quality and high-efficiency recycling of WIS,and it is of great significance to save resources and protect the environment.This study applies a geopolymer prepared from WIS fly ash as a stabilizing agent in WIS blending macadam for use as a pavement base mixture,and reports the mechanical properties(unconfined compressive strength,splitting strength,and resilience modulus)of the geopolymer-stabilized WIS blending macadam(GeoWIS).The leaching concentrations of harmful heavy metals of GeoWIS soaked in water were also investigated.Finally,the strength formation and heavy metal stability mechanisms were explored.The unconfined compressive strength,splitting strength,and compressive resilient modulus of GeoWIS all increased with increasing geopolymer content and decreasing WIS content.The strength of GeoWIS was derived from its geopolymerization and hydration products(C-S-H gel,N-A-S-H gel,and AFt).When the geopolymer content reached 12%–14%,the GeoWIS without natural macadam met the strength criterion of the asphalt pavement base.Through physical adsorption and chemical bonding,the geopolymer significantly reduced the leaching of harmful heavy metals.In GeoWIS with 50%WIS and stabilized with 10%geopolymer,the Cr,Ni,Cd,and Pb concentrations met the grade III groundwater standard.Concentrations of heavy metals leached from GeoWIS are low and exert little impact on environment.
基金supported by the National Natural Science Foundation of China Project 51868058,52068058Inner Mongolia Natural Science Foundation 2018MS05011Inner Mongolia“Grassland Talent”CYYC5039.
文摘The destruction of concrete building materials in severely cold regions of the north is more severely affected by freeze-thaw cycles,and the relationship between the mechanical properties and pore structure of concrete with fine aggregate from municipal solid waste(MSW)incineration bottom ash after freeze-thaw cycles is analyzed under the degree of freeze-thaw hazard variation.In this paper,the gray correlation method is used to calculate the correlation between the relative dynamic elastic modulus,compressive strength,and microscopic porosity parameters to speculate on the most important factors affecting their changes.The GM(1,1)model was established based on the compressive strength of the waste incineration ash aggregate concrete,the relative error between the simulated and actual values in the model was less than 5%,and the accuracy of the model was level 1,indicating that the GM(1,1)model can well reflect the change in the compressive strength of the MSW incineration bottom ash aggregate concrete during freeze-thaw cycles.Using the gray correlation method,the correlation between the relative dynamic elastic modulus,compressive strength,air content,specific surface area,pore spacing coefficient,and pore average chord length was calculated,and the pore spacing coefficient and pore average chord length were determined to be highly correlated with each other.This determination can help analyze and infer the deterioration mechanism of concrete subject to freeze-thaw cycles.These results can provide a theoretical basis for guiding the engineering practice of concrete with fine aggregates of household bottom ash in the northern cold region.
文摘Garbage incineration is an ideal method for the harmless and resource-oriented treatment of urban domestic waste.However,current domestic waste incineration power plants often face challenges related to maintaining consistent steam production and high operational costs.This article capitalizes on the technical advantages of big data artificial intelligence,optimizing the power generation process of domestic waste incineration as the entry point,and adopts four main engine modules of Alibaba Cloud reinforcement learning algorithm engine,operating parameter prediction engine,anomaly recognition engine,and video visual recognition algorithm engine.The reinforcement learning algorithm extracts the operational parameters of each incinerator to obtain a control benchmark.Through the operating parameter prediction algorithm,prediction models for drum pressure,primary steam flow,NOx,SO2,and HCl are constructed to achieve short-term prediction of operational parameters,ultimately improving control performance.The anomaly recognition algorithm develops a thickness identification model for the material layer in the drying section,allowing for rapid and effective assessment of feed material thickness to ensure uniformity control.Meanwhile,the visual recognition algorithm identifies flame images and assesses the combustion status and location of the combustion fire line within the furnace.This real-time understanding of furnace flame combustion conditions guides adjustments to the grate and air volume.Integrating AI technology into the waste incineration sector empowers the environmental protection industry with the potential to leverage big data.This development holds practical significance in optimizing the harmless and resource-oriented treatment of urban domestic waste,reducing operational costs,and increasing efficiency.
文摘The phosphorus recovery from the incinerated ash using NaOH by the heat treatment,was investigated.In this method,non-reacted NaOH containing alkali water was generated with the phosphorus recovery.In order to find out the best method for reuse of the alkali water,the alkali water was mixed with new reagent of NaOH,and the phosphorus recovery was carried out.The phosphorus was recovered as a sodium phosphate,and the recovery rate was almost the same even with the reuse of the alkali water.
基金supported by the National Natural Science Foundation of China (No. 50776007)the Beijing Municipal Science and Technology Commission under the Municipal Solid Waste Development Program(No. H020620330120)
文摘The impact of moisture on the partitioning of the heavy metals including Pb,Zn,Cu and Cd in municipal solid waste (MSW) was studied in a laboratory tubular furnace.A thermodynamic investigation using CHEMKIN software was performed to compare the experimental results.Simulated waste,representative of typical MSW with and without chlorine compounds,was burned at the background temperature of 700 and 950°C,respectively.In the absence of chlorine,the moisture content has no evident effect on the volatility of Pb,Zn and Cu at either 700 or 950°C,however,as flue gas moisture increasing the Cd distribution in the bottom ash increased at 700°C and reduced at 950°C,respectively.In the presence of chlorine,the flue gas moisture reduced the volatility of Pb,Zn and Cu due to the transformation of the more volatile metal chlorides into less volatile metal oxides,and the reduction became significant as chlorine content increase.For Cd,the chlorine promotes its volatility through the formation of more volatile CdCl 2.As a result,the increased moisture content increases the Pb,Zn,Cu and Cd concentrations in the bottom ash,which limits the utilization of the bottom ash as a construction material.Therefore,in order to accumulate heavy metals into the fly ash,MSW should be dried before incineration.
基金Project supported by the Hi-Tech Research and Development Program (863) of China (No. 2002AA644010) the National Tenth-Five Year Program of China (No. 2003BA604A-11-07).
文摘Basic properties of fly ash samples from different urban waste combustion facilities in China were analyzed using as X-ray fluorescence (XRF), scanning electron microscopy (SEM), X-ray diffraction (XRD). The leaching toxicity procedure and some factors influencing heavy metals distribution in fly ash were further investigated. Experimental results indicate that the fly ash structures are complex and its properties are variable. The results of XRF and SEM revealed that the major elements (〉10000 mg/kg, listed in decreasing order of abundance) in fly ash are O, Ca, Cl, Si, S, K, Na, Al, Fe and Zn. These elements account for 93% to 97%, and the content of Cl ranges from 6.93% to 29.18 %, while that of SiO2 does from 4.48% to 24.84%. The minor elements (1000 to 10000 mg/kg) include Cr, Cu and Pb. Primary heavy metals in fly ash include Zn, Pb, Cr, Cu etc. According to standard leaching test, heavy metal leaching levels vary from 0 to 163.10 mg/L (Pb) and from 0.049 to 164.90 mg/L (Zn), mostly exceeding the Chinese Identification Standard for hazardous wastes. Morphology of fly ash is irregular, with both amorphous structures and polycrystalline aggregates. Further research showed that heavy metals were volatilized at a high furnace temperature, condensed when cooling down during the post-furnace system and captured at air pollution control systems. Generally, heavy metals are mainly present in the forms of aerosol particulates or tiny particulates enriched on surfaces of fly ash particles. The properties of fly ash are greatly influenced by the treatment capacities of incinerators or the variation of waste retention time in chamber. Fly ash from combustors of larger capacities generally has higher contents of volatile component and higher leaching toxicity, while those of smaller capacities often produce fly ash containing higher levels of nonvolatile components and has lower toxicity. The content of heavy metals and leaching toxicity maybe have no convincing correlation, and high alkali content of CaO greatly contribute to leaching toxicity of heavy metal and acid neutralization capacity against acid rain.
文摘At present,all kinds of municipal solid waste incineration (MSWI) fly ash stabilization technology has been reported and successfully applied in many countries.However,leaching procedures are very different that the technologies lack uniform standard,and it is even impossible to predict the long-term stabilization.Geochemical model can explain the environmental stabilization based on chemical phase and thermodynamic crystal structure,and it is also able to guide the development of environment-friendly stabi...
基金The Key Projects of Chinese Academy of Sciences(No.KY95T-03-02)the National Natural Science Foundation of China(No.59776023)
文摘Great differences between municipal solid wastes (MSW) produced at different places and different times in terms of such parameters as physical ingredient and heating value lead to difficulty in effective handling of MSW. In this paper, ingredient, heating value and their temporal varying trends of typical MSW in Beijing were continuously measured and analyzed. With consideration of the process in pyrolysis and incineration, correlation between physical ingredients and heating values was induced, favorable for evaluation of heating value needed in handling of MSW from simple analysis of physical ingredients of it.