Randomized scheduling algorithm for input-queued switches

The sampling problem for input-queued (IQ) randomized scheduling algorithms is analyzed.We observe that if the current scheduling decision is a maximum weighted matching (MWM),the MWM for the next slot mostly falls in those matchings whose weight is closed to the current MWM.Using this heuristic,a novel randomized algorithm for IQ scheduling,named genetic algorithm-like scheduling algorithm (GALSA),is proposed.Evolutionary strategy is used for choosing sampling points in GALSA.GALSA works with only O(N) samples which means that GALSA has lower complexity than the famous randomized scheduling algorithm,APSARA.Simulation results show that the delay performance of GALSA is quite competitive with respect to that of APSARA.

STF:PROVIDE RATE GUARANTEES IN INPUT-QUEUED SWITCH

A QoS-aware input-queued scheduling algorithm, called Smallest Timestamp First (STF), is proposed, which is improved upon iSLIP and can allocate bandwidth among inputs sharing a common output based on their reservation by assigning suitable finishing tiniest-amps to contending cells. STF can also provide isolation between flows that share a common output, link. Misbehaving flows will be restricted to guarantee the behaving flows' bandwidth. Simulations prove the feasibility of our algorithm.

Fast and Noniterative Scheduling in Input-Queued Switches

Most high-end switches use an input-queued or a combined input- and output-queued architecture. The switch fabrics of these architectures commonly use an iterative scheduling system such as iSLIP. Iterative schedulers are not very scalable and can be slow. We propose a new scheduling algorithm that finds a maximum matching of a modified I/O mapping graph in a single iteration (hence noniterative). Analytically and experimentally, we show that it provides full throughput and incurs very low delay;it is fair and of low complexity;and it outperforms traditional iterative schedulers. We also propose two switch architectures suited for this scheduling scheme and analyze their hardware implementations. The arbiter circuit is simple, implementing only a FIFO queue. Only half as many arbiters for an iterative scheme are needed. The arbiters operate in complete parallel. They work for both architectures and make the hardware implementations sim-ple. The first architecture uses conventional queuing structure and crossbar. The second one uses separate memories for each queue at an input port and a special crossbar. This crossbar is simple and also has a re-duced diameter and distributed structure. We also show that the architectures have good scalability and re-quire almost no speedup.

AN EFFICIENT SCHEDULING ALGORITHM FOR INPUT-QUEUED SWITCHES

This letter presents an efficient scheduling algorithm DTRR (Dual-Threshold Round Robin) for input-queued switches. In DTRR, a new matched input and output by round robin in a cell time will be locked by two self-adaptive thresholds whenever the queue length or the wait-time of the head cell in the corresponding Virtual Output Queue (VOQ) exceeds the thresholds. The locked input and output will be matched directly in the succeeding cell time until they are unlocked. By employing queue length and wait-time thresholds which are updated every cell time simultane- ously, DTRR achieves a good tradeoff between the performance and hardware complexity. Simula- tion results indicate that the delay performance of DTRR is competitive compared to other typical scheduling algorithms under various traffic patterns especially under diagonal traffic.

Wedge-shaped HfO_(2) buffer layer-induced field-free spin-orbit torque switching of HfO_(2)/Pt/Co structure

Field-free spin-orbit torque(SOT)switching of perpendicular magnetization is essential for future spintronic devices.This study demonstrates the field-free switching of perpendicular magnetization in an HfO_(2)/Pt/Co/TaO_(x) structure,which is facilitated by a wedge-shaped HfO_(2)buffer layer.The field-free switching ratio varies with HfO_(2)thickness,reaching optimal performance at 25 nm.This phenomenon is attributed to the lateral anisotropy gradient of the Co layer,which is induced by the wedge-shaped HfO_(2)buffer layer.The thickness gradient of HfO_(2)along the wedge creates a corresponding lateral anisotropy gradient in the Co layer,correlating with the switching ratio.These findings indicate that field-free SOT switching can be achieved through designing buffer layer,offering a novel approach to innovating spin-orbit device.

Control method based on DRFNN sliding mode for multifunctional flexible multistate switch

To address the low accuracy and stability when applying classical control theory in distribution networks with distributed generation,a control method involving flexible multistate switches(FMSs)is proposed in this study.This approach is based on an improved double-loop recursive fuzzy neural network(DRFNN)sliding mode,which is intended to stably achieve multiterminal power interaction and adaptive arc suppression for single-phase ground faults.First,an improved DRFNN sliding mode control(SMC)method is proposed to overcome the chattering and transient overshoot inherent in the classical SMC and reduce the reliance on a precise mathematical model of the control system.To improve the robustness of the system,an adaptive parameter-adjustment strategy for the DRFNN is designed,where its dynamic mapping capabilities are leveraged to improve the transient compensation control.Additionally,a quasi-continuous second-order sliding mode controller with a calculus-driven sliding mode surface is developed to improve the current monitoring accuracy and enhance the system stability.The stability of the proposed method and the convergence of the network parameters are verified using the Lyapunov theorem.A simulation model of the three-port FMS with its control system is constructed in MATLAB/Simulink.The simulation result confirms the feasibility and effectiveness of the proposed control strategy based on a comparative analysis.

Tunable Three-Wavelength Fiber Laser and Transient Switching between Three-Wavelength Soliton and Q-Switched Mode-Locked States

We report a passive mode-locked fiber laser that can realize single-wavelength tuning and multi-wavelength spacing tuning simultaneously.The tuning range is from 1528 nm–1560 nm,and up to three bands of soliton states can be output at the same time.These results are confirmed by a nonlinear Schrodinger equation model based on the split-step Fourier method.In addition,we reveal a way to transform the multi-wavelength soliton state into the Q-switched mode-locked state,which is period doubling.These results will promote the development of optical communication,optical sensing and multi-signal pulse emission.

Interpolated Bumpless Transfer Control for Asynchronously Switched Linear Systems

This paper revisits the problem of bumpless transfer control(BTC) for discrete-time nondeterministic switched linear systems. The general case of asynchronous switching is considered for the first time in the field of BTC for switched systems. A new approach called interpolated bumpless transfer control(IBTC) is proposed, where the bumpless transfer controllers are formulated with the combination of the two adjacent modedependent controller gains, and are interpolated for finite steps once the switching is detected. In contrast with the existing approaches, IBTC does not necessarily run through the full interval of subsystems, as well as possesses the time-varying controller gains(with more flexibility and less conservatism) achieved from a control synthesis allowing for the stability and other performance of the whole switched system. Sufficient conditions ensuring stability and H_(∞) performance of the underlying system by IBTC are developed, and numerical examples verify the theoretical findings.

Switching Frequency Improvement of a High Speed on/off Valve Based on Pre-excitation Control Algorithm

The high-speed on/off valve(HSV)serves as the fundamental component responsible for generating discrete fluids within digital hydraulic systems.As the switching frequency of the HSV increases,the properties of the generated discrete fluid approach those of continuous fluids.Therefore,a higher frequency response characteristic of HSV is the key to ensure the control accuracy of digital hydraulic systems.However,the current research mainly focuses on its dynamic performance,but neglect its FRC.This paper presents a theoretical analysis demonstrating that the FRC of the HSV can be enhanced by minimizing its switching time.The maximum switching frequency(MSF)is mainly determined by opening dynamic performance when HSV operates with low switching duty ratio(SDR),whereas the closing dynamic performance limits the MSF when HSV operates with high SDR.Building upon these findings,the pre-excitation control algorithm(PECA)is proposed to reduce the switching time of the HSV,and consequently enhance its FRC.Experimental results demonstrate that PECA shortens the opening delay time of HSV by 1.12 ms,the closing delay time by 2.54 ms,and the closing moving time by 0.47 ms in comparison to the existing advanced control algorithms.As a result,a larger MSF of 417 Hz and a wider controllable SDR range from 20%to 70%were achieved at a switching frequency of 250 Hz.Thus,the proposed PFCA in this paper has been verified as an effective and promising approach for enhancing the control performance of digital hydraulic systems.

Iron regulatory protein 1: the deadly switch of ferroptosis

Ferroptosis,an iron-dependent cell death:Ferroptosis is a type of regulated necrosis,characterized by redox-active iron accumulation and increased free radical production derived by Fenton chemistry,that triggers oxidation of polyunsaturated fatty acids in phospholipids,loss of cellular membranes integrity,and leakage of intracellular contents.

Review of Three-phase Soft Switching Inverters and Challenges for Motor Drives

For electric vehicles (EVs),it is necessary to improve endurance mileage by improving the efficiency.There exists a trend towards increasing the system voltage and switching frequency,contributing to improve charging speed and power density.However,this trend poses significant challenges for high-voltage and high-frequency motor controllers,which are plagued by increased switching losses and pronounced switching oscillations as consequences of hard switching.The deployment of soft switching technology presents a viable solution to mitigate these issues.This paper reviews the applications of soft switching technologies for three-phase inverters and classifies them based on distinct characteristics.For each type of inverter,the advantages and disadvantages are evaluated.Then,the paper introduces the research progress and control methods of soft switching inverters (SSIs).Moreover,it presents a comparative analysis among the conventional hard switching inverters (HSIs),an active clamping resonant DC link inverter (ACRDCLI) and an auxiliary resonant commuted pole inverter (ARCPI).Finally,the problems and prospects of soft switching technology applied to motor controllers for EVs are put forward.

Recent advancements in continuously scalable conversion-ratio switched-capacitor converter

Switched-capacitor(SC)DC-DC converter[1]is an impor-tant alternative to inductive DC-DC converter,in terms of removing the bulky power inductor.Hence,it is widely used in low-profile,low-power applications,such as the internet of things(IoT)sensor nodes and energy harvesting[2].Mean-while,considering that capacitor has a much higher energy density than inductor,high-power applications.

An LED-Side-Pumped Intracavity Frequency-Doubled Nd,Ce:YAG Laser Producing a 2W Q-Switched Red Beam

We report a high-average-power acousto-optic(AO)Q-switched intracavity frequency-doubled red laser based on a high-efficiency light-emitting-diode(LED)pumped two-rod Nd,Ce:YAG laser module.Under quasi-continuous wave operation conditions,a maximum output power of 1319.08 nm wavelength was achieved at 11.26 W at a repetition rate of 100 Hz.

Chalcogenide Ovonic Threshold Switching Selector

Today’s explosion of data urgently requires memory technologies capable of storing large volumes of data in shorter time frames,a feat unattain-able with Flash or DRAM.Intel Optane,commonly referred to as three-dimensional phase change memory,stands out as one of the most promising candidates.The Optane with cross-point architecture is constructed through layering a storage element and a selector known as the ovonic threshold switch(OTS).The OTS device,which employs chalcogenide film,has thereby gathered increased attention in recent years.In this paper,we begin by providing a brief introduction to the discovery process of the OTS phenomenon.Subsequently,we summarize the key elec-trical parameters of OTS devices and delve into recent explorations of OTS materials,which are categorized as Se-based,Te-based,and S-based material systems.Furthermore,we discuss various models for the OTS switching mechanism,including field-induced nucleation model,as well as several carrier injection models.Additionally,we review the progress and innovations in OTS mechanism research.Finally,we highlight the successful application of OTS devices in three-dimensional high-density memory and offer insights into their promising performance and extensive prospects in emerging applications,such as self-selecting memory and neuromorphic computing.

Fault Diagnosis Scheme for Railway Switch Machine Using Multi-Sensor Fusion Tensor Machine

Railway switch machine is essential for maintaining the safety and punctuality of train operations.A data-driven fault diagnosis scheme for railway switch machine using tensor machine and multi-representation monitoring data is developed herein.Unlike existing methods,this approach takes into account the spatial information of the time series monitoring data,aligning with the domain expertise of on-site manual monitoring.Besides,a multi-sensor fusion tensor machine is designed to improve single signal data’s limitations in insufficient information.First,one-dimensional signal data is preprocessed and transformed into two-dimensional images.Afterward,the fusion feature tensor is created by utilizing the images of the three-phase current and employing the CANDE-COMP/PARAFAC(CP)decomposition method.Then,the tensor learning-based model is built using the extracted fusion feature tensor.The developed fault diagnosis scheme is valid with the field three-phase current dataset.The experiment indicates an enhanced performance of the developed fault diagnosis scheme over the current approach,particularly in terms of recall,precision,and F1-score.

Performance of Lateral 4H-SiC Photoconductive Semiconductor Switches by Extrinsic Backside Trigger

Photoconductive semiconductor switch(PCSS)can be applied in pulsed high power systems and microwave techniques.However,reducing the damage and increasing the lifetime of silicon carbide(SiC)PCSS are still faced severe challenges.In this study,PCSSs with various structures were prepared on 4-inch diameter,500μm thick high-purity semi-insulating 4H-SiC substrates and their on-state resistance and damage mechanisms were investigated.It was found that the PCSS of an Au/TiW/Ni electrode system annealed at 950℃had a minimum on-state resistance of 6.0Ωat 1 kV bias voltage with a 532 nm and 170 mJ pulsed laser by backside illumination single trigger.The backside illumination single trigger could reduce on-state resistance and alleviate the damage of PCSS compared to the frontside trigger when the diameter of the laser spot was larger than the channel length of PCSS.For the 200 s trigger test by a 10 Hz laser,the black branch-like ablation on Au/TiW/Ni PCSS was mainly caused by thermal stress owing to hot carriers.Replacing metal Ni with boron gallium co-doped zinc oxide(BGZO)thin films annealed at 400℃,black branch-like ablation was alleviated while concentric arc damage was obvious at the anode.The major causes of concentric arc are both pulsed laser diffraction and thermal effect.

An analytical transient coal permeability model:Sorption non-equilibrium index-based swelling switch

Long-term permeability experiments have indicated that sorption-induced swelling can switch from internal to bulk depending on the evolutive sorption status.However,this sorption swelling switch mechanism has not been considered in current analytical permeability models.This study introduces a normalized sorption non-equilibrium index(SNEI)to characterize the sorption status,quantify the dynamical variations of matrix swelling accumulation and internal swelling partition,and formulate the sorption swelling switch model.The incorporation of this index into the extended total effective stress concept leads to an analytical transient coal permeability model.Model results show that the sorption swelling switch itself results in the permeability switch under stress-constrained conditions,while the confined bulk swelling suppresses the permeability recovery to the continuous reduction under displacement-constrained conditions.Model verifications show that current experimental observations correspond to the early stages of the transient process,and they could be extended to the whole process with these models.This study demonstrates the importance of the sorption swelling switch in determining permeability evolution using simple boundary conditions.It provides new insights into experimentally revealing the sorption swelling switch in the future,and underscores the requirement of a rigorous model for complex coupled processes in large-scale coal seams.

Resistive Switching of BN-based Films Accompanied with the Modulation of Ferromagnetism

Nanostructured BN and BN-Co films with Cu,Co,Au as the top electrodes,and Pt as the bottom electrodes were grown by magnetron sputtering.Both BN samples and BN-Co ones show bipolar resistive switching behaviors.For the sample with active Cu as the top electrode,the formation and rupture of metallic Cu conductive filaments can explain the resistive switching behavior;for the other samples,the generation and annihilation of nitrogen vacancies under the electric stimuli may contribute to the occurrence of resistive switching.Taking advantage of the formed and broken Co-N bonds during resistive switching,the saturation magnetization of the BN-Co films can be modulated.Thus,it investigated the resistive switching behavior of BN and BN-Co materials in this work.Similar to that of oxide materials,the resistive switching behaviors of the nitrides may be attributed to the movement of cations or anions within the dielectric or electrodes during the application of voltage.Additionally,ion migration may lead to the formation or breaking of Co-N bonds,which can effectively regulate the magnetism of BN-Co materials.This study extends resistive switching materials to nitrides,enabling the regulation of magnetism along with resistance changes,thus providing insights for the design of novel voltage-controlled magnetic devices and achieving multi-functionality.

Mixed-mode fast-slow oscillations in the frequency switching Duffing system with a 1:n frequency ratio

Sliding fast-slow oscillations are interesting oscillation patterns discovered recently in the Duffing system with frequency switching.Such oscillations have been obtained with a fixed 1:2 low frequency ratio in the previous work.The present paper aims to explore composite fast-slow dynamics when the frequency ratio is variable.As a result,a novel route to composite fast-slow dynamics is obtained.We find that,when presented with variable frequency ratios in a 1:n fashion,the sliding fast-slow oscillations may turn into the ones characterized by the fact that the clusters of large-amplitude oscillations of relaxational type are exhibited in each period of the oscillations,and hence the mixedmode fast-slow oscillations.Depending on whether the transition of the trajectory is from the upper subsystem via the fold bifurcation or not,these interesting oscillations are divided into two classes,both of which are investigated numerically.Our study shows that,when the frequency ratio n is increased from n=3,newly created boundary equilibrium bifurcation points may appear on the original sliding boundary line,which is divided into smaller parts,showing sliding and downward crossing dynamical characteristics.This is the root cause of the clusters,showing large-amplitude oscillations of relaxational type,resulting in the formation of mixed-mode fast-slow oscillations.Thus,a novel route to composite fast-slow dynamics by frequency switching is explained.Besides,the effects of the forcing on the mixed-mode fast-slow oscillations are explored.The magnitude of the forcing frequency may have some effects on the number of large-amplitude oscillations in the clusters.The magnitude of the forcing amplitude determines whether the fast-slow characteristics can be produced.

Resistive switching behavior and mechanism of HfO_(x) films with large on/off ratio by structure design

Different bilayer structures of HfO_(x)/Ti(TiO_(x)) are designed for hafnium-based memory to investigate the switching characteristics. The chemical states in the films and near the interface are characterized by x-ray photoelectron spectroscopy,and the oxygen vacancies are analyzed. Highly improved on/off ratio(~104) and much uniform switching parameters are observed for bilayer structures compared to single layer HfO_(x) sample, which can be attributed to the modulation of oxygen vacancies at the interface and better control of the growth of filaments. Furthermore, the reliability of the prepared samples is investigated. The carrier conduction behaviors of HfO_(x)-based samples can be attributed to the trapping and de-trapping process of oxygen vacancies and a filamentary model is proposed. In addition, the rupture of filaments during the reset process for the bilayer structures occur at the weak points near the interface by the recovery of oxygen vacancies accompanied by the variation of barrier height. The re-formation of fixed filaments due to the residual filaments as lightning rods results in the better switching performance of the bilayer structure.