Effects of Spinning Process on Intergranular Corrosion Behavior of 5A06 Aluminum Alloy

Aluminum alloy tubes were prepared by tube spinning.The intergranular and electrochemical corrosion tests were used to investigate the intergranular corrosion behavior of the 5A06 aluminum alloy blank sample and the spinning sample.Results showed that the intergranular corrosion resistance of the spinning sample was higher than that of the blank sample.In addition,the electrochemical corrosion resistance of the spinning sample was higher than that of the blank sample.The EDS maps indicated a uniform element distribution pattern of aluminum and magnesium.Moreover,the phase composition and lattice constant of the samples were obtained by XRD analysis.The differences in microstructure between the aluminum alloy subjected to the spinning process and the untreated aluminum alloy were determined by EBSD.The differences were mainly attributed to the complex interactions among grain size,dislocations and grain boundaries.

Diversity of intergranular corrosion and stress corrosion cracking for 5083 Al alloy with different grain sizes

5083 Al alloy sheets with different grain sizes(8.7-79.2 μm) were obtained by cold rolling and annealing. Their microstructures, intergranular corrosion(IGC), stress corrosion cracking(SCC), and crack propagation behaviors were investigated. The results showed that samples with coarse grains exhibit better IGC resistance with a corrosion depth of 15 μm. The slow strain rate test results revealed that fine-grained samples exhibit better SCC resistance with a susceptibility index(ISSRT) of 11.2%. Furthermore, based on the crack propagation mechanism, grain refinement can improve the SCC resistance by increasing the number of grain boundaries to induce the corrosion crack propagation along a tortuous path. The grains with {011} orientation could hinder crack propagation by orientating it toward the low-angle grain boundary region. The crack in the fine-grained material slowly propagates due to the tortuous path, and low H;and Cl;concentrations.

Intergranular corrosion behavior of high nitrogen austenitic stainless steel

The intergranular corrosion （IGC） behavior of high nitrogen austenitic stainless steel （HNSS） sensitization treated at 650-950℃ was investigated by the double loop electrochemical potentiodynamic reactivation （DL-EPR） method. The effects of the electrolytes, scan rate, sensitizing temperature on the susceptibility to IGC of HNSS were examined. The results show that the addi-tion of NaCl is an effective way to improve the formation of the cracking of a passive film in chromium-depleted zones during the reactivation scan. Decreasing the scan rate exhibits an obvious effect on the breakdown of the passive film. A solution with 2 mol/L H2SO4＋1 mol/L NaCl＋0.01 mol/L KSCN is suitable to check the susceptibility to IGC of HNSS at a sensitizing temperature of 650-950℃ at a suitable scan rate of 1.667 mV/s. Chromium depletion of HNSS is attributed to the precipitation of Cr2N which results in the susceptibility to IGC. The synergistic effect of Mo and N is suggested to play an important role in stabilizing the passive film to prevent the attack of IGC.

Transformation mechanism of secondary phase and its effect on intergranular corrosion in laser wire filling welding Ni-based alloy/304 stainless steel

To clarify the transformation mechanism of secondary phase and the mechanism of intergranular corrosion in laser welding Ni-based alloy (Hastelloy C-276)/304 stainless steel with filler wire,the secondary phase was analyzed by electron probe micro-analysis (EPMA) and transmission electron microscopy (TEM).The evaluation of intergranular corrosion resistance of the welded joints was conducted by double-loop electrochemical potentiokinetic reactivation(DL-EPR) method,and at the same time the chemical compositions of the corrosion surface were analyzed by energy-dispersive spectrometry (EDS).The results show that p phase has complete coherence relationship withμphase,and the coherent relationship is described as[001]p//■and[430]p//[0001]μ.Theμphase is rapidly transformed from p phase,which is the inhomogeneous phase transformation.The transformation of secondary phase will increase the susceptibility to intergranular corrosion.Therefore,the transformation of secondary phase should be avoided in the welding process.

Effects of Aging Treatment on Intergranular Corrosion and Stress Corrosion Cracking Behavior of AA7003

In order to study the effects of aging treatment on the intergranular corrosion（IGC） and stress corrosion cracking（SCC） of 7003 aluminum alloy（AA7003）, the intergranular corrosion test, electrochemical test and slow strain rate test（SSRT）, combined with optical microscopy（OM） and scanning electron microscopy（SEM） as well as transmission electron microscopy（TEM） observations have been carried out. The IGC and electrochemical test results showed that the IGC resistance of AA7003 for peak aged（PA） temper is the lowest, with double peak aged（DPA） the moderate, and retrogression and re-aging（RRA） the highest among three tempers, which is attributed to the continuous feature of precipitation on grain boundary of PA temper and the interrupted feature of precipitation on grain boundary of DPA and RRA tempers, as well as the wide precipitation free zones（PFZ） of RRA temper. In addition, the SSRT results indicated that all three tempers AA7003 are susceptible to SCC in IGC solution, and the change tendency of SCC susceptibility（ISCC） of AA7003 for three tempers follows the order： ISCC（RRA）

Effects of interrupted ageing and asymmetric rolling on microstructures, mechanical properties, and intergranular corrosion behavior of Al-Mg-Si-Zn alloy

Effects of interrupted ageing(T6I6) and asymmetric rolling on microstructures, mechanical properties, and intergranular corrosion(IGC) behaviors of Al-Mg-Si-Zn alloy were investigated. Results showed that the T6 alloy has the lowest strength and the worst IGC resistance, while the T6I6 alloy has higher strength and better IGC resistance.What’ s more, the alloy treated by pre-rolling deformation has higher strength and better IGC resistance;and the alloy treated by the pre-asymmetry rolling achieves the highest strength, the best IGC resistance and lower elongation. The mechanical properties depend on microstructures such as the grain size, texture, dislocation density and precipitation, the grain boundary misorientation and grain boundary microstructure are responsible for the IGC resistance.

Intergranular Corrosion of UNS S31803 Heat Treated at 800 ℃ Varying Range Times

The aim of this work is evaluate the intergranular corrosion on UNS S31803 steel, with heat treatments at 800 ℃, varying treatment times of 30 mins, 360 mins and 1,440 mins. The results confirm the formation of o phases and secondary austenite （γ2）. For the analysis of the influence of o and γ2 phases, metallographic analysis were conducted through optical microscopy, potentiokinetic reactivation electrochemical techniques and potentiodynamic polarization in NaCI 3.5% solution. Microstructural analysis has shown a formation of γ2 and o phase in heat treatment, due to diffusion of chromium and molybdenum from δ phase to y phase, precipitating on δ/γ and δ/δ interfaces. The DL-EPR （Double loop electrochemical potentiokinetic reactivation） results have shown an increase of the DOS （degree of sensitization） for long periods of time on heat treatment. The results of potentiodynamic polarization showed a reduction of the corrosion and pitting potentials, followed by an increase of the current density when the UNS S31830 steel is heat treated during long periods of time.

Intergranular Corrosion of AISI 304 Heat Treated at 800℃ Varying Range Times

Austenitic stainless steels, when exposed to welding conditions or aging for length of service, it＇s observed the formation of numerous deleterious phases, such as several kinds of carbides type MC, M6C, M7C3, M23C6, and intermetallic secondary phases （sigma, chi, laves）, which cause the process of intergranular corrosion. The aim of this work was verifying the formation of the types of carbides and/or intermetallic phases existing in the stainless AISI 304 at 800 ℃, varying the timing of heat treatment between 30, 360 and 1,440 min. The optical microscopy analysis revealed the predominant formation of the carbide type M23C6. The results of DL-EPR （double loop electrochemical potentiokinetic reactivation） tests showed a gradual increase in the precipitation of this carbide with the increase of treatment time. The potentiodynamic polarization showed that the precipitation of this carbide reduce the formation of the Cr2O3 passive layer, suggesting that the precipitate carbide to be predominantly of the Cr23C6 type.

Acoustic emission detection of 316L stainless steel welded joints during intergranular corrosion

This study analyzes acoustic emission （AE） signals during the intergranular corrosion （IGC） process of 316L stainless steel welded joints under different welding currents in boiling nitric acid. IGC generates several AE signals with high AE activity. The AE technique could hardly distinguish IGC in stainless steel welded joints with different welding heat inputs. However, AE signals can effectively distinguish IGC characteristics in different corrosion stages. The IGC resistance of a heat-affected zone is lower than that of a weld zone. The initiation and rapid corrosion stages can be distinguished using AE results and microstructural analysis. Moreover, energy count rate and amplitude are considered to be ideal parameters for characterizing different IGC processes. Two types of signals are detected in the rapid corrosion stage. It can be concluded that grain boundary corrosion and grain separation are the AE sources of type 1 and type 2, respectively.

INTERGRANULAR CORROSION AND PHOSPHOR SEGREGATION AT GRAIN BOUNDAR1FS OF NON-SENSITIZED SUPERPURE AUSTENITIC STAINLESS STEEL 00Cr25Ni22Mo2N

The corrosion behaviour and mechanism of superpure austenitic stainless steel 00Cr25Ni22Mo2N in urea processing environment was studied using metallography,SEM, TEM,SIMS and AES techniques.The results show that the gas extraction tube made of non-sensitized 00Cr25Ni22Mo2N steel suffered intergranular corrosion.Corrosive media penetrated not only into the tube wall through grain boundaries but also expanded from the boundary towards the interior of the grain.Neither depletion of Cr nor precipitates were found at the grain boundaries.However,P(and Si)was segregated at the grain boundaries to a great extent.Semiquantitative calculation indicates that the P content at the grain boundaries is about 25 wt-%,three orders of magnitude higher than the content within the grain.Sugges- tion is made that the potential difference between the grain and its boundary due to the segre- gation results in the observed intergranular corrosion.

Effect of interrupted aging on mechanical properties and corrosion resistance of 7A75 aluminum alloy

The effects of interrupted aging on mechanical properties and corrosion resistance of 7A75 aluminum alloy extruded bar were investigated through various analyses,including electrical conductivity,mechanical properties,local corrosion properties,and slow strain rate tensile stress corrosion tests.Microstructure characterization techniques such as metallographic microscopy,scanning electron microscopy(SEM),and transmission electron microscopy(TEM)were also employed.The results indicate that the tensile strength of the alloy produced by T6I6 aging is similar to that produced by T6I4 aging,and it even exceeds 700 MPa.Furthermore,the yield strength increases by 52.7 MPa,reaching 654.8 MPa after T6I6 aging treatment.The maximum depths of intergranular corrosion(IGC)and exfoliation corrosion(EXCO)decrease from 116.3 and 468.5μm to 89.5 and 324.3μm,respectively.The stress corrosion factor also decreases from 2.1%to 1.6%.These findings suggest that the alloy treated with T6I6 aging exhibits both high strength and excellent stress corrosion cracking resistance.Similarly,when the alloy is treated with T6I4,T6I6 and T6I7 aging,the sizes of grain boundary precipitates(GBPs)are found to be 5.2,18.4,and 32.8 nm,respectively.The sizes of matrix precipitates are 4.8,5.7 and 15.7 nm,respectively.The atomic fractions of Zn in GBPs are 9.92 at.%,8.23 at.%and 6.87 at.%,respectively,while the atomic fractions of Mg are 12.66 at.%,8.43 at.%and 7.00 at.%,respectively.Additionally,the atomic fractions of Cu are 1.83 at.%,2.47 at.%and 3.41 at.%,respectively.

Application of Grain Boundary Engineering to Improve Intergranular Corrosion Resistance in a Fe–Cr–Mn–Mo–N High-Nitrogen and Nickel-Free Austenitic Stainless Steel

Optimization of grain boundary engineering(GBE) process is explored in a Fe–20Cr–19Mn–2Mo–0.82N high-nitrogen and nickel-free austenitic stainless steel, and its intergranular corrosion(IGC) property after GBE treatment is experimentally evaluated. The proportion of low Σ coincidence site lattice(CSL) boundaries reaches 79.4% in the sample processed with 5% cold rolling and annealing at 1423 K for 72 h;there is an increase of 32.1% compared with the solution-treated sample. After grain boundary character distribution optimization, IGC performance is noticeably improved. Only Σ3 boundaries in the special boundaries are resistant to IGC under the experimental condition. The size of grain cluster enlarges with increasing fraction of low ΣCSL boundaries, and the amount of Σ3 boundaries interrupting the random boundary network increases during growth of the clusters, which is the essential reason for the improvement of IGC resistance.

Nonequilibrium Grain Boundary Segregation of Sulfur and Its Effect on Intergranular Corrosion for 304 Stainless Steel

The data obtained by bending tests for intergranular embrittlement after 45 h and 450 h exposure to Strauss solution have been reported for 304 stainless steel. The results show that an embrittlement peak appears at 650℃ for all samples quenched from 1260℃ and then sensitized for 150 h at 480, 565, 650, 730, 815 and 900℃ respectively. The temperature corresponding to the embrittlement peak is decreased to 565℃ when the sensitizing time is prolonged to 1 500 h. In this paper, these data are analyzed with an isothermal kinetic model of nonequilibrium grain boundary segregation, indicating that the embrittlement peak is related to the critical time for nonequilibrium grain boundary segregation of sulfur.

Current-driving intergranular corrosion performance regeneration below the precipitates solvus temperature in Al–Mg alloy

Heat treatment is an effective method to improve the intergranular corrosion resistance of the sensitized Al–Mg alloy due to dissolution of the grain boundary precipitates above the solvus temperature ofβ-phase.The grain boundary precipitates will grow and coarsening below the solvus temperature.In this study,the in-situ intergranular corrosion performance regeneration of the sensitized Al–Mg alloy can be realized by low-density electro-pulsing treatment below the solvus temperature ofβ-phase.Our findings show that the dissolution of grain boundary precipitates by electro-pulsing treatment is accelerated at relatively low temperature in comparison to traditional heat treatment.The athermal effect produced by the interaction between atoms and electrons on the dissolution of grain boundary precipitates is the main reason for the improved corrosion resistance below the solvus temperature ofβ-phase.

Intergranular corrosion of spark plasma sintered 2024 aluminum alloy at different heat treatment states

2024 aluminum alloys were consolidated by using spark plasma sintering(SPS) method,and then heat treated by solid solution treatment(SST) and aging treatment(AT) procedures.The average grain size of bulk samples sintered with 5,20 and 50 μm powders was 3.72,4.73 and 8.11 μm,respectively.The difference between the average grain size and original powder size was attributed to the recrystallization during short sintering process.The number of the inclusion phases in these samples decreased after SST and increased after subsequent AT.Besides,it was observed that intergranular corrosion(IGC) cracks initiated from stable pits due to the electrochemical inhomogeneity between the intermetallic particles(IMPs) and the aluminum matrix(176.02,110.83 and 164.80 mV for as-SPS,as-SST and as-AT samples,respectively).Besides,the cracks would propagate along the grain boundaries(GBs) and bypass the IMPs at GBs during propagation.It was revealed that the sample after SST presented the best IGC resistance,and this was ascribed to the reduce of IMPs,both in size and number.

Effect of Precipitation on Intergranular Corrosion Resistance of 430 Ferritic Stainless Steel

With Nb-Ti-stabilized 430 ferritic stainless steel（NTS430FSS） and SUS 430 ferritic stainless steel（SUS430FSS） as experimental materials, the influence of precipitation on intergranular corrosion resistance was investigated. A series of aging treatment were carried out. The free-exposure corrosion test and double loop electrochemical potentiokinetic reactivation（DL-EPR） test with a scan rate of 1.67 m V/s at 26 °C were applied to evaluate the intergranular corrosion（IGC） resistance. Metallographic observation, scanning electron microscope（SEM）, transmission electron microscope（TEM） with energy dispersive spectroscopy（EDS） and X-ray diffraction（XRD） analysis were conducted. The results show that IGC occurred in SUS430 FSS aged above 700 °C, while it occurred in NTS430 FSS as the temperature was improved to 1 050 °C. The critical degree of sensitization Ir/Ia reaches 0.305 in SUS430 FSS, which is higher than that of NTS430 FSS, i.e. 0.010, aged at 950 °C for 2 h. The TEM, EDS and XRD results show that a large amount of Cr23C6 precipitates with size of 60 nm×22 nm are located at the SUS430 FSS grain boundaries as chains. With the addition of Nb and Ti and reduction of C, the amount of precipitates reduces significantly in NTS430 FSS. A majority of Cr23C6 were replaced by Ti C and Nb C. Only a small amount of spherical Ti C（R=186 nm） and square Ti N（312 nm×192 nm） with Nb and Cr adsorbed are left along grain boundaries. Due to the dual stabilization of Nb and Ti, the precipitation of Cr23C6 is restrained, the chromium depleted region is avoided and accordingly the resistance to the intergranular corrosion is improved.

Investigation of Susceptibility to Intergranular Corrosion of Tin-Added Austenitic Stainless Steel

The intergranular corrosion （IGC） character of tin-added B316LX and the influence of tin addition on IGC susceptibility were investigated by DL-EPR, oxalic acid etch test and transmission electron microscopy. IGC susceptibility of B316LX is mainly caused by the precipitation of M23C6 carbide and intermetallic Laves phase. DL-EPR test is unsuitable to evaluate the IGC susceptibility of B316LX with long-time sensitization, because more carbides and inter- metallic phases are formed at grain boundaries and inside the grains, which induce more severe IGC and pits attacks. Tin addition increases the IGC susceptibility, maybe due to diffusion of tin toward grain boundaries.

Effect of Shot Peening and Plasma Electrolytic Oxidation on the Intergranular Corrosion Behavior of 7A85 Aluminum Alloy

The effects of shot peening（SP） and plasma electrolytic oxidation（PEO） on the intergranular corrosion behavior of the novel high strength aluminum alloy 7A85（AA 7A85） were investigated by electrochemical polarization and electrochemical impedance tests.The intergranular corrosion mechanism of SP,PEO and PEO combined with sealingtreated AA 7A85 was studied by the metallographic analysis,residual stress testing,X-ray diffractometer analysis and scanning electron microscopy.The results show that AA 7A85-T7452 is very sensitive to intergranular corrosion.SP would significantly improve its intergranular corrosion resistance.This is attributed to the combination action of residual compressive stress and grain refinement.PEO would reduce the largest corrosion depth by 41.6%.Moreover,PEO without sealing did not eliminate the intergranular corrosion due to the existence of the micropores and microcracks in the oxide coating.However,PEO combined with the SiO2sol–gel sealing treatment could effectively protect the AA 7A85-T7452 from intergranular corrosion because of the good corrosion resistance and barrier function of the sealed coating.

Effect of grain refinement induced by wire and arc additive manufacture (WAAM) on the corrosion behaviors of AZ31 magnesium alloy in NaCl solution

Additive manufacturing(AM)of Mg alloys has become a promising strategy for producing complex structures,but the corrosion performance of AM Mg components remains unexploited.In this study,wire and arc additive manufacturing(WAAM)was employed to produce single AZ31 layer.The results revealed that the WAAM AZ31 was characterized by significant grain refinement with non-textured crystallographic orientation,similar phase composition and stabilized corrosion performance comparing to the cast AZ31.These varied corrosion behaviors were principally ascribed to the size of grain,where cast AZ31 and WAAM AZ31 were featured by micro galvanic corrosion and intergranular corrosion,respectively.

INTERGRANULAR AND EXFOLIATION CORROSION BEHAVIOUR OF 8090Al-Li ALLOY

The A1-2.79Li-1.3Cu-0.7Mg-0.12Zr(8090) alloy has excellent resistance to intergranular and exfoliation corrosion as naturally aged, worst as peak aged and rather better as underaged than as overaged. The corrosion behaviour of the alloy is closely dependent on its microstructure. Under the peak aging condition, the coarse T_2 phase, which is continuously distributed along grain boundaries, has so low corrosion potential in comparison with the ma- trix, this makes the corrosion resistance of the alloy to be deteriorated by anodic dissolution along grain boundaries.