STEADY-STATE AND IDLE OPTIMIZA-TION OF INTERNAL COMBUSTION ENGINE CONTROL STRATEGIES FOR HYBRID ELECTRIC VEHICLES

A novel steady-state optimization （SSO） of internal combustion engine （ICE） strategy is proposed to maximize the efficiency of the overall powertrain for hybrid electric vehicles, in which the ICE efficiency, the efficiencies of the electric motor （EM） and the energy storage device are all explicitly taken into account. In addition, a novel idle optimization of ICE strategy is implemented to obtain the optimal idle operating point of the ICE and corresponding optimal parking generation power of the EM using the view of the novel SSO of ICE strategy. Simulations results show that potential fuel economy improvement is achieved relative to the conventional one which only optimized the ICE efficiency by the novel SSO of ICE strategy, and fuel consumption per voltage increment decreases a lot during the parking charge by the novel idle optimization of ICE strategy.

Non-linear Torsional Vibration Characteristics of an Internal Combustion Engine Crankshaft Assembly

Crankshaft assembly failure is one of the main factors that affects the reliability and service life of engines.The linear lumped mass method,which has been universally applied to the dynamic modeling of engine crankshaft assembly,reveals obvious simulation errors.The nonlinear dynamic characteristics of a crankshaft assembly are instructionally significant to the improvement of modeling correctness.In this paper,a general expression for the non-constant inertia of a crankshaft assembly is derived based on the instantaneous kinetic energy equivalence method.The nonlinear dynamic equations of a multi-cylinder crankshaft assembly are established using the Lagrange rule considering nonlinear factors such as the non-constant inertia of reciprocating components and the structural damping of shaft segments.The natural frequency and mode shapes of a crankshaft assembly are investigated employing the eigenvector method.The forced vibration response of a diesel engine crankshaft assembly taking into account the non-constant inertia is studied using the numerical integral method.The simulation results are compared with a lumped mass model and a detailed model using the system matrix method.Results of non-linear torsional vibration analysis indicate that the additional excitation torque created by non-constant inertia activates the 2nd order rolling vibration,and the additional damping torque resulting from the non-constant inertia is the main nonlinear factor.The increased torsional angular displacement evoked by the high order excitation torque relates to the non-constant inertia.This research project is aimed at improving nonlinear dynamics theory,and the confirmed nonlinear parameters can be used for the structure design of a crankshaft assembly.

NO_x emission characteristics of hydrogen internal combustion engine

To study the economic advantages of hydrogen internal combustion engine, an experimen- tal study was carried out using a 2.0 L port fuel-injected （PFI） hydrogen internal combustion engine. Influences of fuel-air equivalence ratio φ, speed, and ignition advance angle on heat efficiency were determined. Test results showed that indicated thermal efficiency （ ITE ） firstly increased with fuel- air equivalence ratio, achieved the maximum value of 40. 4% （ φ = 0.3 ）, and then decreased when was more than 0. 3. ITE increased as speed rises. Mechanical efficiency increased as fuel-air equiva- lence ratio increased, whereas mechanical efficiency decreased as speed increased, with maximum mechanical efficiency reaching 90%. Brake thermal efficiency （BTE） was influenced by ITE and me- chanical efficiency, at the maximum value of 35% （φ =0.5, 2 000 r/min）. The optimal ignition ad- vance angle of each condition resulting in the maximum BTE was also studied. With increasing fuel- air equivalence ratio, the optimal ignition angle became closer to the top dead center （ TDC ）. The test results and the conclusions exhibited a guiding role on hydrogen internal combustion engine opti- mization.

Application of non-equal interval GM(1,1)model in oil monitoring of internal combustion engine

The basic difference non-equal interval model GM(1,1) in grey theory was used to fit and forecast data series with non-equal lengths and different inertias, acquired from oil monitoring of internal combustion engines. The fitted and forecasted results show that the length or inertia of a sequence affects its precision very much, i.e. the bigger the inertia of a sequence is, or the shorter the length of a series is, the less the errors of fitted and forecasted results are. Based on the research results, it is suggested that short series should be applied to be fitted and forecasted; for longer series, the newer datum should be applied instead of the older datum to be analyzed by non- equalinterval GM(1,1) to improve the forecasted and fitted precision, and that data sequence should be verified to satisfy the conditions of grey forecasting.

Research on Simulation and Prediction of Internal Combustion Engine Structural Acoustic Radiation

With the purpose of efficiently predicting structural radiated noise of internal combustion engine（I.C.E.）,a new simulation technique is introduced,which is an approach based on boundary element method （BEM）,acoustic transfer vector（ATV） technique and coupled boundary element model and finite element model （BEM-FEM） approach.Analyses of vibration exciting loads,computing structural dynamic characteristics and dynamic responses have led to theoretical results,which are tested on an L6 diesel engine to validate this proposed technique in engineering practice.

Thermal Aspects in Lubrication System Design for Internal Combustion Engines

The mechanical losses in an internal combustion engine cause a significant decrease in the engine’s overall efficiency. Wherever friction work is dissipated a heat load will inevitably appear. This heat load has to be taken care of in some way, usually with both the water-cooling and the lubrication system. Despite its name, one of the major tasks of the latter one is, to draw out heat from between lubricated surfaces. In contrast to the water cooling system, which is primarily designed for cooling the cylinder block, the lubrication system is mainly required for cooling the crankshaft and piston rod bearings. A lubrication system for today’s automotive engines consists of several components, i.e. an oil pump, a pressure relief valve and an oil filter. This study focuses on the dynamic characteristics of a pressure relief valve and how the system temperature is affected by the critical design parameters of the valve. Using a thermodynamic simulation model together with an optimisation strategy makes it possible to express the desired system characteristics. Then, the optimisation strategy seeks for a similar system configuration with help of the model.

Development of Valve Steel for Internal Combustion Engine in China

This paper first briefly introduces the history of the development of China valve steel from mainly adopting valve steel from the former Soviet Uinoin in the fifties, manufacturing by herself in the sixties, to introducing advanced valve steel from other countries and instituting Chinese valve steel system since the seventies.The demand of valve steel for China internal combustion engine including material specification and quantity required at present is discussed. The principal difficulties being faced with in the development of China valve steel at the moment are put forward. Finally, a detailed discussion is made on the development of China valve steel with suggstions of developing 5Cr8Si2 and MF811 martensitic steels, 21 2N austenitic steel used for gasoline engine, 23 8N austenitic steel used for diesel engine, 21 4NWNb high strength austenitic steel and LF2 and LF4 for valve alloy.[WT5”BZ〗

Improvement on Performances of Internal Combustion Engine Using the Technology of Ceramic Coating

This paper introduces a new technology of using ceramic coating on piston rings of an internal combustion engine, and the comparison of mechanical efficiency and performances of an actual engine before and after the application of ceramic coating on the piston rings. The experimental results show that the mechanical efficiency and power output are enhanced by 4% and 2.6%, respectively, with fuel consumption reduced by (2.9%.) Further studies on coating processing and coating materials as well as the reliability and durability will be of great significance in the application and popularization of the new technology.

Analysis and Calibration of Internal Flow Force of EjectorPowered Engine Simulator System in Wind Tunnels

The ejector-powered engine simulator(EPES)system is an important piece of equipment in conducting an influence test of the intake and jet flow in low-speed wind tunnels.In this work,through the analysis of the structure and principle of EPES,three parts of the internal flow force were obtained,namely,the additional resistance before the inlet,the internal flow force in the inlet and the thrust produced by the ejector.On the assumption of one-dimensional isentropic adiabatic flow,the theoretical formulae for calculating the forces were derived according to the measured total pressure,static pressure and total temperature of the internal flow section.Subsequently,a calibration tank was used to calibrate the EPES system.On the basis of the characteristics of the EPES system,the process and method of its calibration were designed in detail,and the model installation interface of the calibration tank was reformed.By applying this method,the repeatability accuracy of the inlet flow rate calibration coefficient was less than0.05%,whereas that of the exhaust flow rate and velocity was less than 0.1%.Upon the application of the calibration coefficients to the correction of the wind tunnel experiment data,the results showed good agreement with the numerical simulation results in terms of regularity and magnitude before stall,which validates the reasonableness and feasibility of the calibration method.Analysis of the calibration data also demonstrated the consistency in the variation law and trend between the theoretical calculation and actual measurement of internal flow force,further reflecting the rationality and feasibility of the theoretical calculation.Nevertheless,the numerical difference was large and further widened with a higher ejection flow rate mainly because of the accuracy of flow measurement and the inhomogeneity of internal flow.The thrust deflection angle of EPES is an important factor in correcting this issue.In particular,the thrust deflection angle becomes larger with small ejection flow and becomes smaller with an increase in flow rate,essentially exhibiting a general change of less than 10°.

Establishment of a CouplingModel for the Prediction of Heat Dissipation of the Internal Combustion Engine Based on Finite Element

The aerodynamics and heat transfer performance in the rear-mounted automobile cabin have an important influence on the engine’s safety and the operational stability of the automobile.The article uses STARCCM and GT-COOL software to establish the 3D wind tunnel model and engine cooling system model of the internal combustion engine.At the same time,we established a 3D artificial coupling model through parameter transfer.The research results show that the heat transfer coefficient decreases with the increase of the comprehensive drag coefficient of the nacelle.This shows that the cabin flow field has an important influence on the heat transfer coefficient.Themainstream temperature rise of the engine room increases with the increase of the engine load.It is proved that vehicle speed affects the amount of heat dissipation of the engine room internal combustion engine under certain load conditions.The article provides a more effective and fast calculation method for the research on the heat dissipation of the internal combustion engine and the optimization of the cooling system equipment.

Research on Measurements for Temperature and Stress of Pistons in Internal Combustion Engine

In both numerical simulation and experimental research for the piston of internal combustion engine, the verification foundations are always insufficient. The reason is the measurements for its transient temperature and stress under actual operation conditions are very difficult. A multi-channel measurement-storage technology is used in the engine bench experiment to measure the piston temperature and stress in real time. The temperature and stress changes in the engine operation process are obtained. They provide reliable instructive criteria for numerical analysis and experiment of the piston working state.

Fault Identification of Internal Combustion Engine based on Support Vector Machine and Fuzzy Neural Network

The internal combustion engine is the main power source of current large⁃scale machinery and equipment.Overhaul and maintenance of its faults are important conditions for ensuring the safe and stable operation of machinery and equipment,and the identification of faults is a prerequisite.Therefore,the fault identification of internal combustion engines is one of the important directions of current research.In order to further improve the accuracy of the fault recognition of internal combustion engines,this paper takes a certain type of internal combustion engine as the research object,and constructs a support vector machine and a fuzzy neural network fault recognition model.The binary tree multi⁃class classification algorithm is used to determine the priority,and then the fuzzy neural network is verified.The feasibility of the model is proved through experiments,which can quickly identify the failure of the internal combustion engine and improve the failure processing efficiency.

Application of the monitoring and early warning system for internal solitary waves:Take the second natural gas hydrates production test in the South China Sea as an example

Internal solitary waves(ISWs) contain great energy and have the characteristics of emergency and concealment. To avoid their damage to offshore engineering, a new generation of monitoring and early warning system for ISWs was developed using technologies of double buoys monitoring, intelligent realtime data transmission, and automatic software identification. The system was applied to the second natural gas hydrates(NGHs) production test in the Shenhu Area, South China Sea(SCS) and successfully provided the early warning of ISWs for 173 days(from October 2019 to April 2020). The abrupt changes in the thrust force of the drilling platform under the attack of ISWs were consistent with the early warning information, proving the reliability of this system. A total of 93 ISWs were detected around the drilling platform. Most of them occurred during the spring tides in October–December 2019 and April 2020, while few of them occurred in winter. As suggested by the theoretical model, the full-depth structure of ISWs was a typical current profile of mode-1, and the velocities of wave-induced currents can reach 80 cm/s and30 cm/s, respectively, in the upper ocean and near the seabed. The ISWs may be primarily generated from the interactions between the topography and semidiurnal tides in the Luzon Strait, and then propagate westward to the drilling platform. This study could serve as an important reference for the early warning of ISWs for offshore engineering construction in the future.

Research on Risk Evaluation Method for International Engineering Projects

Risk evaluation is one of the important elements of international engineering project management. The risk factors of international engineering projects are systematically analyzed from multiple dimension features of the projects. The muhilayer evaluation index system for the international engineering project risk assessment is proposed and constructed, which consists of 8 I-grade indexes and 24 II-grade indexes as policy risk, market risk, resource risk, and technical scheme risk, schedule risk, funding risk, personnel risk and management risk. And then the self-evaluation and benchmarking evaluation methods are applied to evaluate the international engineering project risk, and established the corresponding mathematical models. Finally, a project evaluation example is given to illustrate the applicability and effectiveness of the mathematical models.

The 13th International Conference on Hydroscience & Engineering

The International Conference on Hydroscience & Engineering (ICHE) began in Washington DC in 1993. Beijing hosted ICHE in 1995, followed by Cottbus (1998), Seoul (2000), Warsaw (2002), Brisbane (2004), Philadelphia (2006), Nagoya (2008), Chennai (2010), Orlando (2012), Hamburg (2014), and Tainan (2016). The forthcoming 13th International Conference on Hydroscience & Engineering will be held on June 18-22, 2018 in Chongqing, China.

23rd International Conference on Coastal Engineering 4-9 October 1992, Venice, ITALY

Organized by Consiglio Nazional delle Ricerche (CNR), Gruppo Nedonale diIdraulice(GNI) with the support of the Ministry of Public Works and under the auspices of theCoastal Engineering Research Council(CERC) of the American Society of CivilEngineering(ASCE), and co-sponsored by the international Association for Hydraulic of Navi-gation Congress(PIANC) and by the Associazione di Ingegneria Offshore e Marina(AIOM).Aim

Evaluation of Chinese Learning Efficiency of International Students in China

This paper investigates the related factors of Chinese learning engagement and performance of 377 students from three universities in Guangzhou of China,employs the value engineering method,and calculates the value coefficient of learning efficiency.From the value coefficient of Chinese language learning,it proves that over 60%of international students studying in China have a higher efficiency in learning Chinese.

Evaluation of Chinese Learning Efficiency of International Students in China:Comparing by Dimension

This paper introduces the Value Engineering method to calculate the value coefficient of Chinese learning efficiency for 377 international students by dimension.Results suggest that attention should be paid to male,European and American,rural,introverted,and“work or education needs”international students;Give full play to the driving role of the reference-type,explore the space for improving the learning efficiency of the improvement-type and attention-type,and pay attention to the problems of problem-type international students.