PHOTOINITIATED INVERSE EMULSION POLYMERIZATION OF SODIUM ACRYLATE

Photoinitiated inverse emulsion polymerization of sodium acrylate(AANa)in kerosene was carried out at room orlower temperature,using 2,2-dimethoxy-2-phenylacetophenone(DMPA)as the initiator.Kinetic investigations indicated thatthe polymerization could be completed in about 30 min and produce polymer with high molecular weight(10~6～10~7).It wasfound that monomer droplets are the main sites for the polymerization(nucleation).With the increase of DMPAconcentration,polymerization rate(R_p)reaches a maximum value while molecular weight of the produced polymer has anadverse result,but the dependence of R_p on incident light intensity is similar.Influences of other parameters such asmonomer concentration,emulsifier content and reaction temperature,etc.were also studied.At lower pH values of waterphase,R_p depends strongly on the pH due to the electrostatic interaction between the ionized radicals and the monomer.Athigher pH,R_p shows a slight dependence on pH.

Microstructure and Properties of PET Fabric Grafted by Polyacrylic Acid with Inverse Microemulsion Polymerization

Annual production output of poly(ethylene terephthalate)(PET) fiber has been over 15 million tons in China due to its good mechanical properties and processability,but the shortage of hydrophilic group of PET has imposed many limitations to further extend its application.The PET fabrics were grafted with polyacrylic acid in inverse microemulsion after low pressure plasma treatment,and the microstructure and properties of the grafted fabrics were investigated with infrared spectroscopy,scanning electron microscope(SEM),hydrophilic and mechanical tests.The grafting yield was increased with the grafting time.The grafting polymer was in the granular form with its particle size ranging from a few micrometers to a dozen of micrometers,normally smaller than the fiber diameter.The moisture regain and water uptake increased while the air permeability of the grafted fabrics decreased with the increase of grafting yield.The bending rigidity and tensile properties show slightly complicated behaviors with grafting yield.The inverse emulsion grafting technique can be used to control the grafting polymer architecture.

Investigation on the Inverse Emulsion Polymerization of Acrylic Acid

Polyacrylic acid particles in nano-scale were synthesized using an inverse (W/O) emulsion polymerization method. The particle size and size change of inverse micelles which solubilize a part of monomer solution was monitored by PCS (photon correlation spectroscopy) and the particles of polyacrylic acid were viewed in scanning electron microscope for the first time. It was concluded that the inverse micelles were primarily the polymerization reaction sites.

INFLUENCES OF WATER-SOLUBLE CATIONIC MONOMERS ON THE POLYMERIZATION RATE IN THE INVERSE EMULSION

This investigation deals with the free radical polymerization both of (2-methacryloyloxyethyl) trimethyl ammonium chloride (QACEMA) and of diallyldimethyl ammonium chloride (DADMAC) in inverse emulsion. The influences of some factors, such as the concentration of monomers, initiator and emulsifier are discussed. The polymerization rate equations of above two monomers can be written as follows: R(p) = k[M](1.21)[I](0.82)[E](0.57) (for QACEMA) R(p) = k'[M](1.34)[I](0.90)[E](0.62) (for DADMAC)

Monitor of Polymerization of Inverse Microemulsions Containing Methyl Methacrylate and Acrylic Acid

The polymerization of the inverse microemulsions composed of methyl methacrylate,acrylic acid, sodium dodecyl sulfate and water was monitored by refractometer, conductometer and time-resolved light scattering device. The results showed that refractive index, conductivity or intensity distribution of scattered light changed along with polymerization, and different processes of polymerization could be identified.

Investigation of the Electro-Mechanical Behavior of Hybrid Polyaniline/Graphene Nanocomposites Fabricated by Dynamic Interfacial Inverse Emulsion Polymerization

This paper describes a study on electrical resistivity under loading of polyaniline (PANI)/graphene nanocomposite powders and compacts. The composites were prepared by an in-situ interfacial dynamic inverse emulsion polymerization technique under sonication of aniline in the presence of graphene sheets in chloroform. During polymerization the graphene nanoplatelets are coated with PANI and are well dispersed both in the polymeric suspension and then in the dried polymer matrix as evidenced by cryogenic transmission electron microscopy (Cryo-TEM) and high resolution scanning microscopy (HRSEM). The presence of graphene nanoplatelets lowers the electrical resistivity of the polyaniline by two orders of magnitude for both the powder and the compact composites as demonstrated by their electrical resistance measurements conducted under loading. The lowest measured electrical resistivity values were 5 Ω·cm for 33% wt. graphene powder and 8 Ω·cm for 41% wt. graphene compacted composites. Cyclic electrical measurements under loading showed a distinct reproducible dependence of the bulk resistivity vs. applied pressure. This repetition is a key component for electro-mechanical sensors. To the authors’ best knowledge, this is the first report on polymerization of aniline in presence of graphene by the in-situ interfacial dynamic inverse emulsion polymerization technique and also the first report on cyclic electrical measurements under pressure of PANI/graphene nanocomposites.

Mechanism and Modeling for Polymerization of Acrylamide in Inverse Microemulsions

After discussion on the mechanism of polymer particle nucleation and growth in inverse microemulsion polymerization, a schematic physical model for polymerization of acrylamide in inverse microemulsions was presented. Furthermore, several key problems in mathematically modeling of inverse microemulsion polymerization were pointed out.

THE PREPARATION OF DOXORUBICIN-POLYVINYLPYRROLIDONE-NANOPARTICLES BY INVERSE EMULSION POLYMERIZATION

Doxorubicin-loaded nanoparticles,using doxorubicin(ADM)as model drug and vinylpyrrolidone as matrix,were prepared by inverse emulsion polymerization in the paper.The nanoparticles were characterized by telescope electron microscopy(TEM),laser light scattering technique(LLS)and infrared spectrum(IR).LLS test showed that the optimal prepared ADM-loaded nanoparticles had an average size 18.8nm and a narrow size distribution between 15nm and 32nm,which was consistent with the result obtained by TEM.And IR results indicated that the nanoparticles consisted of ADM and polyvinylpyrrolidone(PVP).

PARTICLE MORPHOLOGY OF POLY(VINYL CHLORIDE)RESIN PREPARED BY SUSPENDED EMULSION POLYMERIZATION

Suspended emulsion polymerization was used to prepare poly(vinyl chloride) (PVC) resin. Fine PVC particleswere formed at low polymerization conversions. The amount of fine panicles decreases as conversion increases anddisappears at conversions greater than 30%. Scanning electron micrographs show that PVC grains are composed of looselycoalesced primary particles, especially for PVC resins prepared in the presence of poly(vinyl alcohol) dispersant. The size ofprimary particles increases and porosity decreases with the increase of conversion. In view of the particle features of PVCresin, a particle formation mechanism including the formation of primary particles and grains is proposed. The formationprocess of primary particles includes the formation of particle nuclei, coalescence of particle nuclei to form primary particles,and growth of primary particles. PVC grains are formed by the coagulation of primary particles. The loose coalescence ofprimary particles is caused by the colloidal stability of primary particles and the low swelling degree of vinyl chloride in the primary particles.

MORPHOLOGY EVOLUTION OF POLY(St-co-BuA)/SILICA NANOCOMPOSITE PARTICLES SYNTHESIZED BY EMULSION POLYMERIZATION

Poly（St-co-BuA）/silica nanocomposite latexes were synthesized via conventional emulsion polymerization in the presence of 3-（trimethoxysilyl）propyl methacrylate modified colloidal nano-silica. The effects of surface property, particle size and content of colloidal nano-silica as well as the concentrations of monomer and surfactant on the morphology of nanocomposite latex particles were investigated by transmission electron microscope （TEM） and scanning electron microscope （SEM） in detail. Various interesting morphologies such as grape-like, Chinese gooseberry-like, pomegranate-like and normal core-shell structures were observed. Droplet nucleation mechanism competing with micelle nucleation mechanism was proposed to explain the morphological evolution of the nanocomposite particles.

Preparation of multihollow P(St-MAA) particles by sequence soap-free/soap emulsion polymerization and followed by stepwise alkali/acid posttreatment

The effects of ionic emulsifier, sodium dodecylbenzene sulfate (SDBS), on the formation of the multihollow structures in sub-micron sized polymer particles produced by alkali/acid posttreatment were investigated. The original latex particles with narrow size distribution were synthesized by a new sequence emulsifier-free/emulsifier emulsion copolymerization of styrene (St) and methacrylic acid (MAA). Results indicated that the pore size decreased and the pore number increased with the increase of SDBS amount, and the morphology of the posttreated latex particles was also significantly influenced by the introducing time of SDBS in the preparation of the original latex particles, and a suitable introducing time was 3 h of polymerization. (c) 2007 Cheng You Kan. Published by Elsevier B.V. on behalf of Chinese Chemical Society. All rights reserved.

Measurement methods of particle size distribution in emulsion polymerization

The particle size distribution of polymer always develops in emulsion polymerization systems,and certain key phenomena/mechanisms as well as properties of the final product are significantly affected by this distribution.This review mainly focuses on the measurement methods of particle size distribution rather than average particle size during the emulsion polymerization process,including the existing off-line,on-line,and in-line measurement methods.Moreover,the principle,resolution,performance,advantages,and drawbacks of various methods for evaluating particle size distribution are contrasted and illustrated.Besides,several possible development directions or solutions of the in-line measurement technology are explored.

PREPARATION AND CHARACTERIZATION OF AFFINITY POLYMER BASIC MICROSPHERES BY SOAP-FREE EMULSION POLYMERIZATION

Poly(styrene-co-glycidyl methacrylate) latex microspheres with uniform size and high-density epoxy groups on the surface were prepared by soap-free emulsion polymerization with batch wise operation mode in the presence of 2.2′- azobis(2-methylpropionamidine) dihydrochloride as an initiator.The kinetics of soap-free emulsion polymerization and the effects of polymerization factors were examined.In addition,the optimum polymerization conditions of poly(styrene-co- glycidyl methacrylate) latex microspheres for...

Preparation of Self-crosslinked Fluorocarbon Polymer Emulsion with Core-shell Structure by the Method of Soap-free Emulsion Polymerization

Using methyl methacrylate （MMA）, butyl acrylate（BA） and hexafluorobutyl acrylate（HFBA） as main raw materials, we prepared self-crosslinked fluorocarbon polymer emulsion with core-shell structure via soap-free emulsion polymerization when the conception of particle design and polymer morphology was adopted. Moreover, the influence of mole ratio of BA to MAA, pH value on the oligomer was studied. And the effects of the added amount of oligomer, self-crosslinked monomer and HFBA, mass ratio of BA to MMA, reaction temperature and the initiator on the polymerization technology and the performance of the product, were investigated and optimized. The structure and performance of the fluorocarbon polymer emulsion were characterized and tested with FTIR, TEM, MFT and contact angle and water absorption of the latex film. The experimental results show that the optimal conditions for preparing fluorocarbon polymer emulsion are as follows： for preparing the oligomer, tool ratio of BA to MAA is equal to 1.0 ： 1.60, and pH value is controlled within the range of 8.0 and 9.0; for preparing fluorocarbon polymer emulsion, the added amount of oligmer[P（BA/MANa）] is 6%; mass ratio of BA to MMA is 40 ＂ 60; the added amount of self-crosslinked monomer is 2%, the added amount of HFBA is 15 %; reaction temperature is 80 ℃; the mixture of potassium persulfate and sodium bisulfite is used as the initiator. The film-forming stability of the fluorocarbon polymer emul- sion and the performance of the latex film, which is prepared with the soap-free emulsion polymerization, are better than that prepared with the conventional emulsion polymerization.

Influences of Electrolytes on the Soap-free Emulsion Copolymerization of St-MMA-AA

Monodisperse functional polymer microspheres with different particle size and with clean surface were prepared by batch soap-free emulsion polymerization of styrene, methyl methacrylate and acrylic acid in the presence of salts, and the influences of type and amount of electrolytes on polymerization process and particle morphology were investigated. Results showed that there was a critical concentration for different electrolyte to make polymerization process and the resultant emulsion stable, and the particle size increased with the increase of electrolyte concentration. The effect of metal ions was Ca^2＋〉〉K^＋〉Na^＋〉Li^＋, and the effect of haloids was Br〉Cl〉F. Keywords： Electrolyte, soap-free emulsion polymerization, polystyrene, latex particle morphology.

Polyaniline-based electrocatalysts through emulsion polymerization:Electrochemical and electrocatalytic performances

One of the major challenges associated with fuel cells is the design of highly efficient electrocatalysts to reduce the high overpotential of the oxygen reduction reaction (ORR). Here we report Polyaniline (PANI) based micro/nanomaterials with or without transition metals, prepared by the emulsion polymerization and subsequent heat treatment. PANI microspheres with the diameter of about 0.7 mu m have been prepared in basic (NH3 solution) condition, using two different types of surfactant (CTAB, SDS) as the stabilizer, ammonium persulphate (APS) as oxidant with aniline/surfactants molar ratio at 1/1 under the hydrothermal treatment. PANI nanorods, Fe-PANI, and Fe-Co-PANI have been synthesized in acidic (HCI) medium with aniline/surfactants molar ratio at 1/2 and polymerization carried out without stirring for 24 h. Products mainly Fe-Co-PANI have shown high current density with increasing sweep rate and excellent specific capacitance 1753 F/g at the scan rate of 1 mV/s. Additionally, it has shown high thermal stability by thermogravimetric analysis (TGA). Fe-PANI has been investigated for excellent performance toward ORR with four electron selectivity in the basic electrolyte. The PANI-based catalysts from emulsion polymerization demonstrate that the method is valuable for making non-precious metal heterogeneous electrocatalysts for ORR or energy storage and conversion technology. (C) 2016 Science Press and Dalian Institute of Chemical Physics, Chinese Academy of Sciences. Published by Elsevier B.V. and Science Press. All rights reserved.

Preparation of sulphonate-containing core/shell latex particles via seeded emulsion copolymerization

In this study, P（St-MAA） seed latex particles were first prepared via soap-free emulsion polymerization of styrene （St） and methacrylic acid （MAA）, then the seed particles were allowed to swell with St at room temperature, and the P（St-MAA）/P（St- NaSS） core/shell latex particles were then synthesized via seeded emulsion copolymerization of St and sodium styrene sulphonate （NaSS） using AIBN as initiator in the presence of N,N^-methylenebisacrylamide （BAA, water-soluble crosslinker）. Results showed that the polymerization could be carried out smoothly when the ratio of BAA to total monomers was less than 3 mol%, the narrow dispersed P（St-MAA） seed particles with the diameter of 150 nm and the P（St-MAA）/P（St-NaSS） core/shell latexes with the particle size of about 200 nm were synthesized. When the 25/75 mole ratio of NaSS/（St ＋ MAA） and 2 tool% of BAA were used in the seeded emulsion polymerization, the resulted P（St-MAA）/P（St-NaSS） latex product showed a low weight loss after water extraction, and the NaSS unit content in the whole particle and in the shell reached 11.7 mol% and 34.6 mol%, resoectivelv.

Nonionic Polymerizable Emulsifier in High-Solids-Content Acrylate Emulsion Polymerization

Stable high-solids-content acrylate emulsion were obtained with a nonionic polymerizable emulsifier allyloxy nonylphenoxy poly （ethyleneoxy） （10） ether （ANPEO10）, and a conventional emulsifier OP-10 as a reference sample. 1H NMR proves that the polymerizable emulsifier ANPEO10 has been incorporated into the resulted acrylate polymers. TEM demonstrates that there are some differences in the particle morphologies. AFM proves that the polymerizable emulsifier ANPEO10 migrating to the surface of the emulsion film was much less than the conventional emulsifier OP-10. The polymerizable emulsifier ANPEO10 can enhance the adhesion with glass plate compared to the conventional emulsifier. Furthermore, with increasing amount of emulsifier, the surface free energy of the films first decreased and then increased, and the adhesion with glass plate is initially enhanced and then attenuated. The water-resistance and solvent-resistance of the films prepared by the polymerizable emulsifier ANPEO10 are superior to those prepared by the conventional emulsifier OP-10.

Grafting Methyl Methacrylate onto Silk via Emulsion Graft Copolymerization Using a Diethylzinc Complex Initiator

Methyl methacrylate (MMA) was grafted onto silk fiber in a one-step emulsion system using a diethylzinc and 1,10-phenanthroline complex. The reaction conditions were investigated by varying temperature and initiator to monomer ratio. Fourier transform infrared (FTIR) spectrum, thermogravimetric analysis (TGA), and scanning electron microscopy (SEC) techniques were used to characterize the structure, thermal stability, and surface morphology of the obtained product, respectively. Grafting of MMA onto silk increased the thermal stability of silk. The FTIR spectrum and SEM images provided further evidence that MMA has been successfully grafted onto the silk fiber. A peak ascribed to the C=O stretching vibration of MMA was detected in the FTIR spectrum of grafted silk fiber, which was not present in the spectrum of pure silk fiber. Moreover, the SEM images illustrated the increase in diameter and surface roughness of grafted silk compared with pure silk. Lastly, the dyeing performance of the modified silk was significantly increased.