INVESTIGATION ON MICROSTRUCTURE AND TRIBOLOGICAL PROPERITIES OF CORED WIRE ARC SPRAYED Al/Al _2 O_3 COATINGS

Cored wires for electric arc spraying of Al/Al 2 O 3 MMC coatings were developed, with Al 2 O 3 powder as the core material and commercial aluminium strip as the retaining sheath. The bond strength, Al 2 O 3 content, microstructure, micro-hardness and wear resistance of coatings produced by arc spraying of the cored wires were experimentally investigated and were compared with those of pure aluminum coating.

Predicting the composition of flux-cored wire claded metal by a neural network

In this paper, an artificial neural network method that can predict the chemical composition of deposited weld metal by CO 2 Shielded Flux Cored Wire Surfacing was studied. It is found that artificial neural network is a good approach on studying welding metallurgy processes that cannot be described by conventional mathematical methods. In the same time we explored a new way to study the no equilibrium welding metallurgy processes.

STUDYONANEWKINDOFPOWDER－FEEDINGAPPARATUSOFFLUX－COREDWIREPRODUCTIONLINE

A set of electromagnetic vibration powder feeding apparatus of the flux cored wire production line and its single chip controlling system have been designed in this paper. The parameters of the electromagnatic vibration powder feeding apparatus have been tested, the functional relation between powder feeding velocity V L and current I has been made out so that the controlling system can not only automatically make out the quantity of the powder according to the width of the steel belt, powder density, production speed and filling ratio, but also adjust the powder feeding speed according to the real production speed, keeping a stable filling ratio.

USING HIGH Mg-CONTENT CORED-WIRE TO SPHEROIDIZE AND DESULPHURIZE DUCTILE IRON MELT IN INDUSTRIAL EXPERIMENTS

Mg-content cored-wire was used to desulphurize and spheroidize ductile iron melt in industrial experiments. The optimal feeding speed and suitable treatment temperature were determined in the experiments. And cored-wire method and pouring method were compared. Conclusions have been drawn that, under these conditions in the experiments, the optimal feeding speed is 15m/min, treatment temperature should be as low as possible, 1400-1450℃ generally; and cored-wire method can act more effective in ductile iron melt desulphurization and spheroid than pouring method.

Investigation of the impact toughness of self- shielded flux- cored wire girth welds for X80 pipelines

Self-shielded flux-cored wire is a convenient and efficient consumable for pipeline field girth welding because of its self-protection characteristic and high deposition rate, especially for remote construction sites in rugged terrain. From the perspective of pipeline safety, the impact toughness of the girth welds is an important factor in pipeline integrity ,which determines the crack arrest behavior in the girth welds. Therefore, improving the girth weld impact toughness is of primary importance in the field of pipeline girth welding. Three self-shielded flux-cored wires comprising different chemical composition systems have been applied to large diameter X80 UOE （U-ing-O- ing-Expanding） pipeline semi-automatic girth welding,and the impact toughness of the welds has been evaluated by girth weld chemical composition analysis and microstructural analysis using scanning electron microscopy （SEM） and energy dispersive spectrometry （EDS） to investigate pipeline girth weld impact toughness and find ways to improve it. This helps in determining the main factors that influence girth weld impact toughness. Pipeline girth weld impact toughness is mainly determined by the final microstructure produced in the solid-state phase transition. In the as-weld state,acicular ferrite （AF） and fine bainite （FB） are a benefit to the impact toughness. For multilayer semiautomatic self-shielded flux-cored wire welding, the normalizing and tempering function of the latter beads to the initial beads plays an important role in the transition of girth weld microstructure, which affects the impact toughness. The original AF and FB and the corresponding heat treatment microstructure of the fine and uniform block ferrite and pearlite result in very good impact toughness. The following two mechanisms are found to promote the production of AF and FB in the girth weld. First, elements promoting the broadening of the austenitic region, such as Ni, C, Cu, and Mn, induce low temperature phase transitions and restrain the opposing function of Al, which is a benefit to the production of AF and FB. Second, dispersed high-melting-point inclusions, especially Al2O3 ,induce the nucleated production of AF. The advantageous function of inclusions is determined by their shape, distribution, and dimension. Dispersed spherical inclusions of small dimension are a benefit to the production of AF, and result in good impact toughness.

Effects of process parameters on the depth-to-width ratio of flux-cored wire underwater wet welding

The effects of process parameters on the depth-to-width ratio （D/W） of flux-cored wire underwater wet welding with a certain type of homemade .flux-cored wire are studied. It is found that the welding .speed, wire feeding speed and torch oscillating amplitude hare significant effects on the dopth-to-width ratio （D/W） of welds. The D/W ratio of welds increases significantly with the increase of welding speed without the oscillating of welding torch. It increased （from 0. 14 to 0. 26 ） with the increase of wire feeding speed while the torch oscillating. And it decreased linearly with the increase of torch oscillating amplitude. However, the influelwe of oscillating speed, wire extension and welding voltage on the D/W ratio of welds was not obvious.

STUDY ON FLUX-CORED WIRE FOR ELECTRIC ARC SPRAYING AND PROPERTIES OF COATING

According to the characteristics of electric arc spraying technology and abrasion of boiler piping,a flux cored wire SMD 45 for electric arc spraying is developed The experimental results show that the surface hardness of the coating reaches 60～65 HR and the adhesive strength between the coating and base is 23～28 MPa The wearability of the coating sprayed by the wire is 5 times than that of ordinary steel pipe Applying the wire to the heated surface,the life of the economizer pipe is doubly increased No local desquamation,rust and abrasion can be examined during more than one year's service.

Droplet Transfer Behavior of Flux Cored Wire TIG Welding

This paper puts forward a new method to achieve flux cored wire TIG welding and uses high-speed photography to analyze the droplet transfer behavior and forces acting on the droplet. The droplet transfer forms include bridging transfer, slag column guided transfer, and non-contact transfer; each of these forms may be observed as the melting position of the welding wire changes. The important role of surface tension in the process of droplet transfer is proposed using static force balance theory and pinch instability theory. The phenomenon of droplet backward swing during welding process could be attributed to the vapor recoil force produced by vapors from the droplet. The welding experiments show that the proposed welding process is stable and that the weld quality produced is good.

Effects of cooling rate on vermicular graphite percentage in a brake drum produced by onestep cored wire injection

In this research, a vermicular graphite cast iron brake drum was produced by cored wire injection in a one-step method. Silica sand and low-density alumina-silicate ceramic were used as molding materials in order to investigate the effect of cooling rate on percentage of vermicular graphite and mechanical properties of the brake drum casting. Several thermocouples were inserted into the casting in the desired positions to measure the temperature change. By means of one-step cored wire injection, the two residual concentrations of Mg and RE were effectively controlled in the ranges of 0.013%-0.017% and 0.019%-0.025%, respectively, which are crucial for the production of vermicular graphite cast iron and the formation of vermicular graphite. In addition, the cooling rate had a significant effect on the vermicular graphite percentage. In the case of the silica mold brake drum casting, there was an obvious difference in the cooling rate with the wall change, leading to a change in vermicular graphite percentage from 70.8% to 90%. In the low-density alumina-silicate ceramic mold casting, no obvious change in temperature was detected by the thermocouples and the percentage of the vermicular graphite was stable at 85%. Therefore, the vermicular graphite cast iron brake drum with a better combination of mechanical properties could be obtained.

Effects of CeF_3 on properties of self-shielded flux cored wire

Effects of CeF3 on properties of self-shielded flux cored wire including welding process, inclusions in weld metal and mechanical properties are systematically studied. Welding smoke and spatter are reduced with the addition of CeF3. The main non-metallic inclusions in weld metal are AlN and Al2O3. CeF3 can refine non-metallic inclusions and reduce the amount of large size inclusions, which is attributed to the inclusion floating behavior during the solidification of weld metal. The low temperature impact toughness is improved by adding suitable amount of CeF3 in the flux.

Difference in particle characteristics and coating properties between spraying metallic and ceramic powder cored wires

The sprayed particles of metallic and cermet wires were collected to analyze the atomization state of the particles in arc spraying forming, the microstructure and properties of metallic and ceramic coatings were investigated and compared. Particle size analyzer was used for quantifying particle size. The XRD, SEM and optical microscope(OM) were used to analyze the phase composition and microstructure of the particles and coatings. From the experimental results, some difference of particle characteristics was established between the spraying metallic and ceramic cored wires, and the microstructure and properties of coatings depend strongly on the particles behaviors. The result shows that Fe-TiB2/Al2O3 composite coating has a high potential for abrasive wear applications.

Research on the abrasive wear resistance of YDCrMoV coating produced by CO_2 shielded flux-cored wire surfacing

Caterpillar construction machines play an important part in many fields such as hydraulic and electric engineering, the construction of highway, for its particular of structure. The walking system of caterpillar construction machines is always under the condition of three-body abrasive wear. The abrasive wear of walking system is very severe, which always results in damages of components or structures of walking system of caterpillar construction machines. It is very important to repair the walking system by cladding technique. The abrasive wear properties of four kinds coatings produced by the shielded flux-cored wire surfacing for the repair of the damaged components of walking system of caterpillar construction machines have been studied experimentally on an MLS-23 type wet sand rubber wheel abrasive tester. The surfaces morphologies of the abrasively worn specimens and their microstructures are investigated by transmitting electron microscopy (TEM) after wear testing. Results show that the wear mechanism of cladding metals of the flux-cored wire No.1 and the No.2 is micro-cutting while that of the No.3 and the No.4 is micro-ploughing. The four kinds of flux-cored wire coatings present great potential applications for the repairing of caterpillar construction machines in the Three Gorges Engineering.

STUDY ON METAL TRANSFER MODES OF SELF-SHIELDED FLUX-CORED WELDING WIRE

Metal transfer behavior of six kinds of self shielded flux cored wire(SSFCW) is studied using the apparatus of SSFCW high speed photography self made. Six kinds of metal transfer modes of SSFCW were obtained through observation for high speed photograph film and analysis. It is believed that the research is of magnificent for improving operative performance and mechanical properties of SSFCW and dynamics characteristic of welding power.

Computation of the Strand Resistance Using the Core Wire Strain Measurement

This paper proposes a method enabling to compute the prestressing strand resistance using the strain measured on only one core wire. Numerical analysis is conducted considering the pitch length of the strand and the diameters of the core wire and helical wires as parameters. The results verify that the relation between the stresses of the core wire and helical wires can be expressed in terms of the helical angle. Based on this observation, a formula computing directly the prestress force in the strand from the strain measured in the core wire is suggested. Owing to the recently developed measurement method for the core wire strain, the proposed formula can be exploited to determine the prestress of the strand.

Effect of oxygen-containing additives on weld penetration in self-shielded flux cored arc welding

The effect of Fe203 and Liz CO3 additives in flux core on the weld metal oxygen content and weld penetration in self-shielded flux cored arc welding were studied schematically. The result shows that the oxygen content in the weld metal and weld penetration both increased with the Fe203 addition increased in the range of 5 wt. % to 20 wt. %. The oxygen content in the weld metal was increased with the Li2CO3 addition increased in the range of 1 wt. % to 8 wt. %. However, the weld penetration decreased when Li2CO3 addition exceeding 4 wt. %. High-speed photographic images show that when Fe2O3 addition influx core exceeding 15 wt. %, droplet became excessively large, so that spatters were frequently generated in large numbers. In this study, Fe203 and Li2 CO3 in the amount of 11 wt. % and 4 wt. %, respectively, jointly added in the flux core can achieve a deeper weld penetration with sound usability characteristics.

Investigation on mechanism of fixing nitrogen in self-shielded flux cored arc welding

Prevention of nitrogen porosity in weld metal deposited with self-shielded flux cored wire with CaF2-TiO2-MgO slag system can be accomplished by using a 'killing agent' such as titanium to react with nitrogen dissolved in the weld metal. The amount of titanium needed to prevent porosity is calculated thermodynamically for various dissolved nitrogen levels. Experimental flux cored wires are used to verify the thermodynamic model. It is concluded that approximately 0.11 wt% titanium in the weld deposit is need to prevent nitrogen porosity when welding without externally applied shielding.

钻井利器的故事之“液动潜孔锤”

在各种钻探方法中,液动冲击回转钻进具有效率高、质量好、回次长、事故少、成本低等优点,而液动潜孔锤又是液动冲击回转钻进的技术核心。本文梳理了各种液动潜孔锤的结构特点及其与绳索取心钻具、孔底动力钻具相结合衍生的各种钻具,简要介绍了这一技术的典型应用案例,总结归纳了其下一步发展方向和技术难点,以期普及液动锤的应用,促进液动冲击回转钻进技术的进步。

CeO_(2)添加量对电弧增材制造铁基形状记忆合金组织和性能的影响

采用粉芯丝材+电弧增材制造技术制备了含不同质量分数(0,1%,2%,3%)CeO_(2)的Fe-14Mn-6Si-9Cr-5Ni铁基形状记忆合金,研究了CeO_(2)添加量对试验合金显微组织和形状记忆性能的影响。结果表明:添加质量分数1%的CeO_(2)后,合金晶内析出相减少,晶界处析出较大尺寸的稀土化合物,组织均匀,弯曲变形后未出现ε马氏体跨晶生长现象,且马氏体交叉状态较少;当CeO_(2)质量分数增加至2%和3%时,晶内析出相增多,分布均匀性变差,且在弯曲变形后ε马氏体跨晶生长和交叉特征增多;随着CeO_(2)添加量增加,试验合金的晶粒尺寸减小,层错概率增大,形状回复率先增大后减小,当CeO_(2)质量分数为1%时晶粒尺寸较小,层错概率较大,形状回复率最大,形状记忆性能最好。

钛型气保护药芯焊丝工艺质量影响因素综述

综述了涉及钛型气保护药芯焊丝工艺质量的影响因素。结果表明,合理选用药芯添加物,严格控制熔敷金属中主要强化元素C、Mn、Si的含量,可以改善焊丝熔滴过渡形态,获得焊丝熔敷金属满意的力学性能。在Ar+CO_(2)二元混合保护气体中,随着CO_(2)含量增大,熔滴过渡形态从轴向变为非轴向滴状排斥过渡,接头的抗拉强度几乎没有影响,但熔敷金属的冲击吸收能明显下降。热输入较大时,焊丝工艺性变差;热输入居中时,焊丝工艺性较好。热输入对焊丝熔敷金属韧性的影响出现了对热输入敏感和不敏感两种情况。钛型气保护药芯焊丝工艺质量的三个影响因素控制原理各具特色。