金矮生苹果蒸腾速率对光照和水分的响应研究(英文)

We tested the transpiration rate ( Tr ) of seven\|year\|old field and two\|year\|old potted Malus pumila cv.Goldspur under different conditions of illumination and soil water. The results showed that the interrelationship between Tr of Malus pumila cv.Goldspur and illumination and soil water content ( SWC ) was quite remarkable. Tr increased with the increase of light intensity and SWC . However, when one of the environmental stresses of illumination and water existed, the improvement of the other condition couldn't make Tr rise greatly. Only when SWC was higher than 11%, which arrived at over 55% of the field content ( FC ), or the photosynthetic active radiation ( PAR ) higher than 400?μmol·s -1 m -2 , Tr could rise greatly with the increase of PAR or SWC . But when SWC was higher than 15%, which reached over 75% of FC or PAR higher than 1?000?μmol·s -1 ·m -2 , Tr would not change a lot with the change of PAR or SWC . That PAR and SWC influenced the magnitude of stomatic resistance( RS ) and leaf water potential ( Ψ l) was the basic reason for the Tr responded to them. Light stress reduced the open degree of stomas, so when severe light stress existed ( PAR <100?μmol·s -1 ·m -2 ), RS was larger ( RS >2 0?s·cm -1 ), which led to the decrease of Tr(Tr <5?μgH 2O·s -1 ·cm -2 ). When severe water stress existed( SWC <11% and<55% of FC and soil water potential Ψ ws <-1 15?MPa), RS was higher than 4 00?s·cm -1 and Ψ l lower than -2 10?MPa, which led to Tr lower than 11?μgH 2O·s -1 ·cm -2 . When soil water was adequate( SWC >15% amd over 75% of FC , and Ψ ws >-0 50?MPa), RS was lower than 2 00?s·cm -1 , Ψ l higher than -1 65?MPa and Tr would be higher than 15?μgH 2O·s -1 ·m -2 . The range of SWC , 11%～15%, which accounted for 55% to 75% of FC , and correspond RS (2 00～4 00?s·cm -1 ) were the turning area, where the variable curve of Tr transited from a variable trend to another variable one. It could be considered as the range to control soil water.

Effectiveness of hospital disinfection and experience learnt from 11 years of surveillance

This survey was designed to assess the sanitation status of hospitals and the compliance of hospital staff to disinfection strategies within the past 11 years.A total of 199 provincial affiliated tertiary or secondary public hospitals from 2007 to 2017 were investigated and seven critical categories,namely indoor air,work surface,hand hygiene,ultraviolet(UV)irradiation intensity,use of disinfectants,sterilization of medical items,and effects of steam sterilizer,were monitored.The average qualified rates were(94.74±3.54)%(810/855),(97.25±1.65)%(1876/1929),(87.57±4.60)%(2508/2864),(95.00±4.50)%(1196/1259),and(98.76±1.14)%(1599/1619)for indoor air,work surface,hand hygiene,UV irradiation intensity,and sterilization of medical items,respectively.In terms of other categories,few samples were not qualified:3/1575 for use of disinfectants and 1/243 for effects of steam sterilizer.The hospital disinfection monitoring and supervision program effectively improved the effectiveness of disinfection.Routine monitoring and supervision must be conducted to ensure a safe hospital treatment environment.

Hydrodynamic Effects on Surface Morphology Evolution of Titanium Alloy under Intense Pulsed Ion Beam Irradiation

The hydrodynamic effects of molten surface of titanium alloy on the morphology evolution by intense pulsed ion beam （IPIB） irradiation are studied. It is experimentally revealed that under irradiation of IPIB pulses, the surface morphology of titanium alloy in a spatial scale of μm exhibits an obvious smoothening trend. The mechanism of this phenomenon is explained by the mass transfer caused by the surface tension of molten metal. Hydrodynamic simulation with a combination of the finite element method and the level set method reveals that the change in curvature on the molten surface leads to uneven distribution of surface tension. Mass transfer is caused by the relief of surface tension, and meanwhile a flattening trend in the surface morphology evolution is achieved.

Effect of tilt angle on the performance and electrical parameters of a PV module:Comparative indoor and outdoor experimental investigation

Photovoltaic(PV)system’s performance is significantly affected by its orientation and tilt angle.Experimental investigation(indoor and outdoor)has been carried out to trace the variation in PV performance and electrical parameters at varying tilt angles in Malaysian conditions.There were two experimental modus:1)varying module tilt under constant irradiation level,2)varying irradiation intensity at the optimum tilt set up.For the former scheme,the irradiation level was maintained at 750 W/m^(2),and for the later arrangement,the module tilt angle was varied from 0 o to 80 o by means of a single-axis tracker.Results show that under constant irradiation of 750 W/m^(2),every 5 o increase in tilt angle causes a power drop of 2.09 W at indoor and 3.45 W at outdoor.In contrast,for the same condition,efficiency decreases by 0.54%for indoor case and by 0.76%at outdoor.On the other hand,for every 100 W/m^(2)increase in irradiation,solar cell temperature rises by 7.52℃at indoor and by 5.67℃at outdoor.As of module electrical parameters,open-circuit voltage,short-circuit current,maximum power point voltage and maximum power point current drops substantially with increasing tilt angle,whereas fill factor drops rather gradually.Outdoor experimental investigation confirms that the optimum tilt angle at Malaysian conditions is 15 o and orienting a PV module this angle will maximize the sun’s energy captured and thereby enhance its performance.

Heat Leakage Numerical Investigation of a Compound Parabolic ConcentratorPulsating Heat Pipe Solar Collector

As a new type of equipment for solar medium temperature utilization, the compound parabolic concentrator-pulsating heat pipe solar collector(CPC-PHPSC) uses pulsating heat pipe(PHP) as an endotherm, which can realize efficient energy conversion. The design of proper concentration ratio of compound parabolic concentrator(CPC) ensures that the incident sunlight can be concentrated on the evaporator section surface of PHP without solar tracking system. The objective of the present work is to study the influence of solar radiation intensity, air speed, material thickness(glass and insulation board) and tilt angle on the thermal performance of the new collector, which is difficult to control in the experiment. The heat leakage process and characteristics of the CPC-PHPSC were numerically studied by establishing a 3D numerical model of the collector unit. The results show that the theoretical collector efficiency of CPC-PHPSC reaches 74.5%, which is consistent with the experimental results. During operation, the heat collection performance is the best when the tilt angle is 45° and the solar radiation intensity is 1000 W/m^(2), while the excessive air speed will increase the convective heat loss. Increasing the thickness of insulation board and glass has little effect on the collector efficiency.