Mg-air batteries have attracted tremendous attention as a potential next-generation power source for portable electronics and e-transportation due to their remarkable high theoretical volumetric energy density,environ...Mg-air batteries have attracted tremendous attention as a potential next-generation power source for portable electronics and e-transportation due to their remarkable high theoretical volumetric energy density,environmental sustainability,and cost-effectiveness.However,the fast hydrogen evolution reaction(HER)in NaCl-based aqueous electrolytes impairs the performance of Mg-air batteries and leads to poor specific capacity,low energy density,and low utilization.Thus,the conventionally used NaCl solute was proposed to be replaced by NaNO_(3)and acetic acid additive as a corrosion inhibitor,therefore an electrolyte engineering for long-life time Mg-air batteries is reported.The resulting Mg-air batteries based on this optimized electrolyte demonstrate an improved discharge voltage reaching~1.8 V for initial 5 h at a current density of 0.5 mA/cm^(2) and significantly prolonged cells'operational lifetime to over 360 h,in contrast to only~17 h observed in NaCl electrolyte.X-ray photoelectron spectroscopy and time-of-flight secondary ion mass spectrometry were employed to analyse the composition of surface film and scanning electron microscopy combined with transmission electron microscopy to clarify the morphology changes of the surface layer as a function of acetic acid addition.The thorough studies of chemical composition and morphology of corrosion products have allowed us to elucidate the working mechanism of Mg anode in this optimized electrolyte for Mg-air batteries.展开更多
Bacterial colonization of orthopedic implants is one of the leading causes of failure and clinical complexities for load-bearing metallic implants. Topical or systemic administration of antibiotics may not offer the m...Bacterial colonization of orthopedic implants is one of the leading causes of failure and clinical complexities for load-bearing metallic implants. Topical or systemic administration of antibiotics may not offer the most efficient defense against colonization, especially in the case of secondary infection, leading to surgical removal of implants and in some cases even limbs. In this study, laser powder bed fusion was implemented to fabricate Ti3Al2V alloy by a 1:1 weight mixture of CpTi and Ti6Al4V powders. Ti-Tantalum(Ta)–Copper(Cu) alloys were further analyzed by the addition of Ta and Cu into the Ti3Al2V custom alloy. The biological,mechanical, and tribo-biocorrosion properties of Ti3Al2V alloy were evaluated. A 10 wt.% Ta(10Ta) and 3 wt.% Cu(3Cu) were added to the Ti3Al2V alloy to enhance biocompatibility and impart inherent bacterial resistance. Additively manufactured implants were investigated for resistance against Pseudomonas aeruginosa and Staphylococcus aureus strains of bacteria for up to 48 h. A 3 wt.% Cu addition to Ti3Al2V displayed improved antibacterial efficacy, i.e.78%–86% with respect to CpTi. Mechanical properties for Ti3Al2V–10Ta–3Cu alloy were evaluated, demonstrating excellent fatigue resistance, exceptional shear strength, and improved tribological and tribo-biocorrosion characteristics when compared to Ti6Al4V. In vivo studies using a rat distal femur model revealed improved early-stage osseointegration for alloys with10 wt.% Ta addition compared to CpTi and Ti6Al4V. The 3 wt.% Cu-added compositions displayed biocompatibility and no adverse infammatory response in vivo. Our results establish the Ti3Al2V–10Ta–3Cu alloy’s synergistic effect on improving both in vivo biocompatibility and microbial resistance for the next generation of load-bearing metallic implants.展开更多
Perovskite solar cells(PSCs)have been demonstrated to be one of the most promising technologies in the field of renewable energy.However,the presence of the defects in the perovskite films greatly limits the efficienc...Perovskite solar cells(PSCs)have been demonstrated to be one of the most promising technologies in the field of renewable energy.However,the presence of the defects in the perovskite films greatly limits the efficiency and the stability of the PSCs.The additive engineering is one of the most effective approaches to overcome this problem.Most of the successful additives are extracted from the petroleum-based materials,while the research on the biomass-based additives is still lagging behind.In this paper,two ecofriendly hydroxyalkyl cellulose additives,i.e.,hydroxyethyl cellulose(HEC)and hydroxylpropyl cellulose(HPC),are investigated on the performance of the MAPbl_(3)-based inverted PSCs.Due to the strong interaction between the hydroxyl groups of the cellulose and the divalent cations of the perovskite,these additives enhance the crystal grain orientation and significantly repair the defects of the perovskite films.Working as the additives,these two cellulose derivatives show a strong passivation ability,which significantly reduces the trap density and improves the optoelectronic feature of the PSCs.Compared with the average power conversion efficiency(PCE)of the control device(19.19%),an enhancement of~10%is achieved after the addition of HEC.The optimized device(PCE=21.25%)with a long-term stability(10:80 h,PCE=20.93%)is achieved by the incorporation of the HEC additives into the precursor solution.It is the best performance among the PSCs with the cellulose additives up to now.This research provides a novel choice to develop a cost-effective and renewable additive for the PSCs with high efficiency and excellent long-term stability.展开更多
Due to the loss of organic amine cations and lead ions in the structure of the iodine-lead methylamine perovskite solar cell,there are a large number of defects within the film and the recombination loss caused by gra...Due to the loss of organic amine cations and lead ions in the structure of the iodine-lead methylamine perovskite solar cell,there are a large number of defects within the film and the recombination loss caused by grain boundaries,which seriously hinder the further improvement of power conversion efficiency and stability.Herein,a novel carbon nitride C_(3)N_(3) incorporated into the perovskite precursor solution is a multifunctional strategy,which not only increases the light absorption strength,grain size,and hydrophobicity of the perovskite film,but also effectively passivates the bulk and interfacial defects of perovskite and verified by the first-principles density functional theory calculations.As a result,the efficiency and stability of perovskite solar cells are improved.The device with 0.075 mg mL^(-1) C_(3)N_(3) additive delivers a champion power conversion efficiency of 19.91%with suppressed hysteresis,which is significantly higher than the 18.16% of the control device.In addition,the open-circuit voltage of the modified device with the maximum addition as high as 1.137 V is 90.96% of the Shockley–Queisser limit(1.25 V).Moreover,the power conversion efficiency of the modified device without encapsulation can maintain nearly 90% of its initial value after being stored at 25℃ and 60% relative humidity for 500 h.This work provides a new idea for developing additives to improve the power conversion efficiency and stability of perovskite solar cells.展开更多
Semiconducting SrTiO 3 based voltage sensing and dielectric ceramics were prepared by single step sintering with Li 2CO 3 SiO 2 as liquid phase additives.The effects of the content of liquid phase,the ratio o...Semiconducting SrTiO 3 based voltage sensing and dielectric ceramics were prepared by single step sintering with Li 2CO 3 SiO 2 as liquid phase additives.The effects of the content of liquid phase,the ratio of Li/Si and the sintering temperatures on properties were discussed in terms of electrical properties and microstructures of materials.The results showed thatSrTiO 3 based varistor ceramics,with 0.6 mol% Li 2CO 3 SiO 2(Li/Si=3/2) and sintered at 1 380 ℃ in graphite and N 2 reducing atomosphere,had excellent current volatage sensing and dielectric characteristics.展开更多
Biopolymers are promising environmentally benign materials applicable in multifarious applications.They are especially favorable in implantable biomedical devices thanks to their excellent unique properties,including ...Biopolymers are promising environmentally benign materials applicable in multifarious applications.They are especially favorable in implantable biomedical devices thanks to their excellent unique properties,including bioactivity,renewability,bioresorbability,biocompatibility,biodegradability and hydrophilicity.Additive manufacturing(AM)is a flexible and intricate manufacturing technology,which is widely used to fabricate biopolymer-based customized products and structures for advanced healthcare systems.Three-dimensional(3D)printing of these sustainable materials is applied in functional clinical settings including wound dressing,drug delivery systems,medical implants and tissue engineering.The present review highlights recent advancements in different types of biopolymers,such as proteins and polysaccharides,which are employed to develop different biomedical products by using extrusion,vat polymerization,laser and inkjet 3D printing techniques in addition to normal bioprinting and four-dimensional(4D)bioprinting techniques.It also incorporates the influence of nanoparticles on the biological and mechanical performances of 3D-printed tissue scaffolds,and addresses current challenges as well as future developments of environmentally friendly polymeric materials manufactured through the AMtechniques.Ideally,there is a need for more focused research on the adequate blending of these biodegradable biopolymers for achieving useful results in targeted biomedical areas.We envision that biopolymer-based 3D-printed composites have the potential to revolutionize the biomedical sector in the near future.展开更多
Magnesium(Mg)-based materials are a new generation of alloys with the exclusive ability to be biodegradable within the human/animal body.In addition to biodegradability,their inherent biocompatibility and similar-to-b...Magnesium(Mg)-based materials are a new generation of alloys with the exclusive ability to be biodegradable within the human/animal body.In addition to biodegradability,their inherent biocompatibility and similar-to-bone density make Mg-based alloys good candidates for fabricating surgical bioimplants for use in orthopedic and traumatology treatments.To this end,nowadays additive manufacturing(AM)along with three-dimensional(3D)printing represents a promising manufacturing technique as it allows for the integration of bioimplant design and manufacturing processes specific to given applications.Meanwhile,this technique also faces many new challenges associated with the properties of Mg-based alloys,including high chemical reactivity,potential for combustion,and low vaporization temperature.In this review article,various AM processes to fabricate biomedical implants from Mg-based alloys,along with their metallic microstructure,mechanical properties,biodegradability,biocompatibility,and antibacterial properties,as well as various post-AM treatments were critically reviewed.Also,the challenges and issues involved in AM processes from the perspectives of bioimplant design,properties,and applications were identified;the possibilities and potential scope of the Mg-based scaffolds/implants are discussed and highlighted.展开更多
Semiconducting SrTiO 3 based voltage sensing and dielectric ceramics were prepared by single step sintering with Li 2CO 3 SiO 2 as liquid phase additives.The effects of the content of liquid phase,the ratio o...Semiconducting SrTiO 3 based voltage sensing and dielectric ceramics were prepared by single step sintering with Li 2CO 3 SiO 2 as liquid phase additives.The effects of the content of liquid phase,the ratio of Li/Si and the sintering temperatures on properties were discussed in terms of electrical properties and microstructures of materials.The results showed thatSrTiO 3 based varistor ceramics,with 0.6 mol% Li 2CO 3 SiO 2(Li/Si=3/2) and sintered at 1 380 ℃ in graphite and N 2 reducing atomosphere,had excellent current volatage sensing and dielectric characteristics.展开更多
Additive manufacturing and 3D printing tech-nology have been developing rapidly in the last 30 years, and indicate great potential for future development. The promising future of this technology makes its impact on tr...Additive manufacturing and 3D printing tech-nology have been developing rapidly in the last 30 years, and indicate great potential for future development. The promising future of this technology makes its impact on traditional industry unpredictable. 3D printing will propel the revolution of fabrication modes forward, and bring in a new era for customized fabrication by realizing the five "any"s: use of almost any material to fabricate any part, in any quantity and any location, for any industrial field. Innovations in material, design, and fabrication processes will be inspired by the merging of 3D-printing technology and processes with traditional manufacturing processes. Finally, 3D printing will become as valuable for manufacturing industries as equivalent and subtractive manufacturing processes.展开更多
The study aims to demonstrate the suitability of the 3DPMD for the production of titanium components with and without reinforcing particles in layer-by-layer design. Various demonstrators are prepared and analyzed. Th...The study aims to demonstrate the suitability of the 3DPMD for the production of titanium components with and without reinforcing particles in layer-by-layer design. Various demonstrators are prepared and analyzed. The microstructure, the porosity and the hardness values of the different structures are compared with each other through metallographic cross-sections. The uniform distribution of the carbides and the interaction with the matrix was analyzed by SEM and EDX.The miller-test method(ASTM G75-07) was used to determine data for the relative abrasivity of the structures. In summary, 3DPMD offers the possibility to produce titanium structures with and without reinforced particles. Using automated routines, it is possible to generate metal structures using welding robots directly from the CAD drawings. Microstructures and properties are directly related to the process and therefore material-process-property relationships are discussed within this work.展开更多
By employing sintering additives of Li2CO3 and Y2O3,porous Si3N4 ceramics are prepared after experiencing the processes of sintering and post-vacuum heat treatment at 1680 and 1550°C,respectively.The experimental...By employing sintering additives of Li2CO3 and Y2O3,porous Si3N4 ceramics are prepared after experiencing the processes of sintering and post-vacuum heat treatment at 1680 and 1550°C,respectively.The experimental results demonstrate the completed phase transformation fromαtoβ-Si3N4 in Si3N4 ceramic samples with a amount of 1.60 wt%Li2CO3(0.65 wt%Li2O)and 0.33 wt%Y2O3 additives.The as-synthesized porous Si3N4 ceramics exhibit high flexural strength((126.7±2.7)MPa)and high open porosity of 50.4%at elevated temperature(1200°C).These results are attributed to the significant role of added Li2CO3 as sintering additive,where the volatilization of intergranular glassy phase occurs during sintering process.Therefore,porous Si3N4 ceramics with desired mechanical property prepared by altering the addition of sintering additives demonstrate their great potential as a promising candidate for high temperature applications.展开更多
The current study is directed to the rapidly developing field of inorganic material 3D object production at nano-/micro scale.The fabrication method includes laser lithography of hybrid organic-inorganic materials wit...The current study is directed to the rapidly developing field of inorganic material 3D object production at nano-/micro scale.The fabrication method includes laser lithography of hybrid organic-inorganic materials with subsequent heat treatment leading to a variety of crystalline phases in 3D structures.In this work,it was examined a series of organometallic polymer precursors with different silicon(Si)and zirconium(Zr)molar ratios,ranging from 9:1 to 5:5,prepared via sol-gel method.All mixtures were examined for perspective to be used in 3D laser manufacturing by fabricating nano-and micro-feature sized structures.Their spatial downscaling and surface morphology were evaluated depending on chemical composition and crystallographic phase.The appearance of a crystalline phase was proven using single-crystal X-ray diffraction analysis,which revealed a lower crystallization temperature for microstructures compared to bulk materials.Fabricated 3D objects retained a complex geometry without any distortion after heat treatment up to 1400℃.Under the proper conditions,a wide variety of crystalline phases as well as zircon(ZrSiO_(4)-a highly stable material)can be observed.In addition,the highest new record of achieved resolution below 60 nm has been reached.The proposed preparation protocol can be used to manufacture micro/nano-devices with high precision and resistance to high temperature and aggressive environment.展开更多
Silicon carbide (SiC) ceramics have excellent properties and widely used for high temperature applications. So far, joining techniques have been applied to fabricate large SiC ceramics with complicated shapes. In this...Silicon carbide (SiC) ceramics have excellent properties and widely used for high temperature applications. So far, joining techniques have been applied to fabricate large SiC ceramics with complicated shapes. In this work, the additive manufacturing (AM) technique was examined to fabricated SiC ceramics with complicated hollow structures using the Fused Deposition Modeling (FDM) type 3D-printer. To mold the hollow structure for the applications such as heat exchangers, the “support-less” condition must be achieved. Thus, extruded SiC-phenol resin compounds must be cured immediately after molding to keep the molded shapes. To increase the thermal conductivity of the SiC compounds, the combinations of commercial SiC powders with different average diameters were examined for increasing the volume fraction of SiC particles to the phenol resin. SiC compounds with optimized rheological properties for the modified FDM-type 3D-printer were successfully obtained.展开更多
The melting temperature and critical transition temperature Tc of YBa2Cu3O7-δ with deferent content additives of PbO and BaPbO3 were studied. When PbO was doped in YBa2Cu3O7-δ, the melting temperature of YBa2Cu3O7-...The melting temperature and critical transition temperature Tc of YBa2Cu3O7-δ with deferent content additives of PbO and BaPbO3 were studied. When PbO was doped in YBa2Cu3O7-δ, the melting temperature of YBa2Cu3O7-δ was reduced, however its superconductivity was weakened. From the XRD pattern of the sintered mixture of YBa2Cu3O7-δ and PbO, it was known that there was a reaction between YBa2Cu3O7-δ and PbO, and the product was BaPbO3. Hence different contents of BaPbO3 (10mass%, 20mass% and 30mass%) were added in YBa2Cu3O7-δ. It was proved that there were no reactions between YBa2Cu3O7-δ and BaPbO3. And the superconductivity of the mixtures was much better than that of the samples with PbO additive.展开更多
Zinc metal batteries have been considered as a promising candidate for next-generation batteries due to their high safety and low cost.However,their practical applications are severely hampered by the poor cyclability...Zinc metal batteries have been considered as a promising candidate for next-generation batteries due to their high safety and low cost.However,their practical applications are severely hampered by the poor cyclability that caused by the undesired dendrite growth of metallic Zn.Herein,Ti_(3)C_(2)T_(x) MXene was first used as electrolyte additive to facilitate the uniform Zn deposition by controlling the nucleation and growth process of Zn.Such MXene additives can not only be absorbed on Zn foil to induce uniform initial Zn deposition via providing abundant zincophilic-O groups and subsequently participate in the formation of robust solid-electrolyte interface film,but also accelerate ion transportation by reducing the Zn^(2+) concentration gradient at the electrode/electrolyte interface.Consequently,MXene-containing electrolyte realizes dendrite-free Zn plating/striping with high Coulombic efficiency(99.7%)and superior reversibility(stably up to 1180 cycles).When applied in full cell,the Zn-V_(2)O_(5)cell also delivers significantly improved cycling performances.This work provides a facile yet effective method for developing reversible zinc metal batteries.展开更多
Nanocrystalline TiO2 was prepared by high frequency plasma chemical vapor deposition (HF-PCVD). The effects of additive AlCl3 on crystal phase, particle size and microstructurai parameters of TiO2 nanocrystallites wer...Nanocrystalline TiO2 was prepared by high frequency plasma chemical vapor deposition (HF-PCVD). The effects of additive AlCl3 on crystal phase, particle size and microstructurai parameters of TiO2 nanocrystallites were investigated by X-ray diffraction(XRD) and transmission electron microscopy (TEM). The nanocrystallites obtained experimentally are mixture of anatase and rutile, the uniform diameters of particles are about 30 nm. The phase transformation from anatase to rutile was accelerated by AlCl3, and rutile content is increased from 26.7 wt pct to 53.6 wt pct with increasing of addition of AlCl3 from 0.0 wt pct to 5.0 wt pct. The particle size is reduced and the size distribution becomes very narrow. The crystal lattice constants have the trend to decrease, and celi volumes appear as shrinkable.展开更多
基金the China Scholarship Council(CSC)for funding(no.201806310116)。
文摘Mg-air batteries have attracted tremendous attention as a potential next-generation power source for portable electronics and e-transportation due to their remarkable high theoretical volumetric energy density,environmental sustainability,and cost-effectiveness.However,the fast hydrogen evolution reaction(HER)in NaCl-based aqueous electrolytes impairs the performance of Mg-air batteries and leads to poor specific capacity,low energy density,and low utilization.Thus,the conventionally used NaCl solute was proposed to be replaced by NaNO_(3)and acetic acid additive as a corrosion inhibitor,therefore an electrolyte engineering for long-life time Mg-air batteries is reported.The resulting Mg-air batteries based on this optimized electrolyte demonstrate an improved discharge voltage reaching~1.8 V for initial 5 h at a current density of 0.5 mA/cm^(2) and significantly prolonged cells'operational lifetime to over 360 h,in contrast to only~17 h observed in NaCl electrolyte.X-ray photoelectron spectroscopy and time-of-flight secondary ion mass spectrometry were employed to analyse the composition of surface film and scanning electron microscopy combined with transmission electron microscopy to clarify the morphology changes of the surface layer as a function of acetic acid addition.The thorough studies of chemical composition and morphology of corrosion products have allowed us to elucidate the working mechanism of Mg anode in this optimized electrolyte for Mg-air batteries.
基金supported by the National Institute of Arthritis and Musculoskeletal and Skin Diseases of the National Institutes of Health under Award Numbers R01 AR067306 and R01 AR078241。
文摘Bacterial colonization of orthopedic implants is one of the leading causes of failure and clinical complexities for load-bearing metallic implants. Topical or systemic administration of antibiotics may not offer the most efficient defense against colonization, especially in the case of secondary infection, leading to surgical removal of implants and in some cases even limbs. In this study, laser powder bed fusion was implemented to fabricate Ti3Al2V alloy by a 1:1 weight mixture of CpTi and Ti6Al4V powders. Ti-Tantalum(Ta)–Copper(Cu) alloys were further analyzed by the addition of Ta and Cu into the Ti3Al2V custom alloy. The biological,mechanical, and tribo-biocorrosion properties of Ti3Al2V alloy were evaluated. A 10 wt.% Ta(10Ta) and 3 wt.% Cu(3Cu) were added to the Ti3Al2V alloy to enhance biocompatibility and impart inherent bacterial resistance. Additively manufactured implants were investigated for resistance against Pseudomonas aeruginosa and Staphylococcus aureus strains of bacteria for up to 48 h. A 3 wt.% Cu addition to Ti3Al2V displayed improved antibacterial efficacy, i.e.78%–86% with respect to CpTi. Mechanical properties for Ti3Al2V–10Ta–3Cu alloy were evaluated, demonstrating excellent fatigue resistance, exceptional shear strength, and improved tribological and tribo-biocorrosion characteristics when compared to Ti6Al4V. In vivo studies using a rat distal femur model revealed improved early-stage osseointegration for alloys with10 wt.% Ta addition compared to CpTi and Ti6Al4V. The 3 wt.% Cu-added compositions displayed biocompatibility and no adverse infammatory response in vivo. Our results establish the Ti3Al2V–10Ta–3Cu alloy’s synergistic effect on improving both in vivo biocompatibility and microbial resistance for the next generation of load-bearing metallic implants.
基金the National Natural Science Foundation of China(61935017,62175268,21674123,31700507)Fujian Natural Science Foundation for Distinguished Young Scholars(2020J06039)+4 种基金Project of“100 People Planning in Fujian Province,”Fujian Provincial Department of Finance for the research of organic photovoltaic solar cell(Kle20001A)the Science and Technology Development Fund,Macao SAR(File no.FDCT-0044/2020/A1,0082/2021/A2)UM's research fund(File no.MYRG2020-00151-IAPME)Natural Science Foundation of Guangdong Province,China(2019A1515012186)Shenzhen-Hong Kong-Macao Science and Technology Innovation Project(Category C)(SGDX2020110309360100).
文摘Perovskite solar cells(PSCs)have been demonstrated to be one of the most promising technologies in the field of renewable energy.However,the presence of the defects in the perovskite films greatly limits the efficiency and the stability of the PSCs.The additive engineering is one of the most effective approaches to overcome this problem.Most of the successful additives are extracted from the petroleum-based materials,while the research on the biomass-based additives is still lagging behind.In this paper,two ecofriendly hydroxyalkyl cellulose additives,i.e.,hydroxyethyl cellulose(HEC)and hydroxylpropyl cellulose(HPC),are investigated on the performance of the MAPbl_(3)-based inverted PSCs.Due to the strong interaction between the hydroxyl groups of the cellulose and the divalent cations of the perovskite,these additives enhance the crystal grain orientation and significantly repair the defects of the perovskite films.Working as the additives,these two cellulose derivatives show a strong passivation ability,which significantly reduces the trap density and improves the optoelectronic feature of the PSCs.Compared with the average power conversion efficiency(PCE)of the control device(19.19%),an enhancement of~10%is achieved after the addition of HEC.The optimized device(PCE=21.25%)with a long-term stability(10:80 h,PCE=20.93%)is achieved by the incorporation of the HEC additives into the precursor solution.It is the best performance among the PSCs with the cellulose additives up to now.This research provides a novel choice to develop a cost-effective and renewable additive for the PSCs with high efficiency and excellent long-term stability.
基金This work was financially supported by National Natural Science Foundation of China(52002121,62004064,21873027,and 21905219)the Key Program for Inter-governmental S&T Innovation Cooperation Projects of National Key R&D Pro-gram of China(2019YFE0107100)+1 种基金Natural Science Foundation of Hubei Province(2020CFA091)Overseas Expertise Introduction Center for Discipline Innova-tion(D18025).
文摘Due to the loss of organic amine cations and lead ions in the structure of the iodine-lead methylamine perovskite solar cell,there are a large number of defects within the film and the recombination loss caused by grain boundaries,which seriously hinder the further improvement of power conversion efficiency and stability.Herein,a novel carbon nitride C_(3)N_(3) incorporated into the perovskite precursor solution is a multifunctional strategy,which not only increases the light absorption strength,grain size,and hydrophobicity of the perovskite film,but also effectively passivates the bulk and interfacial defects of perovskite and verified by the first-principles density functional theory calculations.As a result,the efficiency and stability of perovskite solar cells are improved.The device with 0.075 mg mL^(-1) C_(3)N_(3) additive delivers a champion power conversion efficiency of 19.91%with suppressed hysteresis,which is significantly higher than the 18.16% of the control device.In addition,the open-circuit voltage of the modified device with the maximum addition as high as 1.137 V is 90.96% of the Shockley–Queisser limit(1.25 V).Moreover,the power conversion efficiency of the modified device without encapsulation can maintain nearly 90% of its initial value after being stored at 25℃ and 60% relative humidity for 500 h.This work provides a new idea for developing additives to improve the power conversion efficiency and stability of perovskite solar cells.
文摘Semiconducting SrTiO 3 based voltage sensing and dielectric ceramics were prepared by single step sintering with Li 2CO 3 SiO 2 as liquid phase additives.The effects of the content of liquid phase,the ratio of Li/Si and the sintering temperatures on properties were discussed in terms of electrical properties and microstructures of materials.The results showed thatSrTiO 3 based varistor ceramics,with 0.6 mol% Li 2CO 3 SiO 2(Li/Si=3/2) and sintered at 1 380 ℃ in graphite and N 2 reducing atomosphere,had excellent current volatage sensing and dielectric characteristics.
文摘Biopolymers are promising environmentally benign materials applicable in multifarious applications.They are especially favorable in implantable biomedical devices thanks to their excellent unique properties,including bioactivity,renewability,bioresorbability,biocompatibility,biodegradability and hydrophilicity.Additive manufacturing(AM)is a flexible and intricate manufacturing technology,which is widely used to fabricate biopolymer-based customized products and structures for advanced healthcare systems.Three-dimensional(3D)printing of these sustainable materials is applied in functional clinical settings including wound dressing,drug delivery systems,medical implants and tissue engineering.The present review highlights recent advancements in different types of biopolymers,such as proteins and polysaccharides,which are employed to develop different biomedical products by using extrusion,vat polymerization,laser and inkjet 3D printing techniques in addition to normal bioprinting and four-dimensional(4D)bioprinting techniques.It also incorporates the influence of nanoparticles on the biological and mechanical performances of 3D-printed tissue scaffolds,and addresses current challenges as well as future developments of environmentally friendly polymeric materials manufactured through the AMtechniques.Ideally,there is a need for more focused research on the adequate blending of these biodegradable biopolymers for achieving useful results in targeted biomedical areas.We envision that biopolymer-based 3D-printed composites have the potential to revolutionize the biomedical sector in the near future.
文摘Magnesium(Mg)-based materials are a new generation of alloys with the exclusive ability to be biodegradable within the human/animal body.In addition to biodegradability,their inherent biocompatibility and similar-to-bone density make Mg-based alloys good candidates for fabricating surgical bioimplants for use in orthopedic and traumatology treatments.To this end,nowadays additive manufacturing(AM)along with three-dimensional(3D)printing represents a promising manufacturing technique as it allows for the integration of bioimplant design and manufacturing processes specific to given applications.Meanwhile,this technique also faces many new challenges associated with the properties of Mg-based alloys,including high chemical reactivity,potential for combustion,and low vaporization temperature.In this review article,various AM processes to fabricate biomedical implants from Mg-based alloys,along with their metallic microstructure,mechanical properties,biodegradability,biocompatibility,and antibacterial properties,as well as various post-AM treatments were critically reviewed.Also,the challenges and issues involved in AM processes from the perspectives of bioimplant design,properties,and applications were identified;the possibilities and potential scope of the Mg-based scaffolds/implants are discussed and highlighted.
文摘Semiconducting SrTiO 3 based voltage sensing and dielectric ceramics were prepared by single step sintering with Li 2CO 3 SiO 2 as liquid phase additives.The effects of the content of liquid phase,the ratio of Li/Si and the sintering temperatures on properties were discussed in terms of electrical properties and microstructures of materials.The results showed thatSrTiO 3 based varistor ceramics,with 0.6 mol% Li 2CO 3 SiO 2(Li/Si=3/2) and sintered at 1 380 ℃ in graphite and N 2 reducing atomosphere,had excellent current volatage sensing and dielectric characteristics.
文摘Additive manufacturing and 3D printing tech-nology have been developing rapidly in the last 30 years, and indicate great potential for future development. The promising future of this technology makes its impact on traditional industry unpredictable. 3D printing will propel the revolution of fabrication modes forward, and bring in a new era for customized fabrication by realizing the five "any"s: use of almost any material to fabricate any part, in any quantity and any location, for any industrial field. Innovations in material, design, and fabrication processes will be inspired by the merging of 3D-printing technology and processes with traditional manufacturing processes. Finally, 3D printing will become as valuable for manufacturing industries as equivalent and subtractive manufacturing processes.
文摘The study aims to demonstrate the suitability of the 3DPMD for the production of titanium components with and without reinforcing particles in layer-by-layer design. Various demonstrators are prepared and analyzed. The microstructure, the porosity and the hardness values of the different structures are compared with each other through metallographic cross-sections. The uniform distribution of the carbides and the interaction with the matrix was analyzed by SEM and EDX.The miller-test method(ASTM G75-07) was used to determine data for the relative abrasivity of the structures. In summary, 3DPMD offers the possibility to produce titanium structures with and without reinforced particles. Using automated routines, it is possible to generate metal structures using welding robots directly from the CAD drawings. Microstructures and properties are directly related to the process and therefore material-process-property relationships are discussed within this work.
基金Project(202045007)supported by the Start-up Funds for Outstanding Talents in Central South University,China。
文摘By employing sintering additives of Li2CO3 and Y2O3,porous Si3N4 ceramics are prepared after experiencing the processes of sintering and post-vacuum heat treatment at 1680 and 1550°C,respectively.The experimental results demonstrate the completed phase transformation fromαtoβ-Si3N4 in Si3N4 ceramic samples with a amount of 1.60 wt%Li2CO3(0.65 wt%Li2O)and 0.33 wt%Y2O3 additives.The as-synthesized porous Si3N4 ceramics exhibit high flexural strength((126.7±2.7)MPa)and high open porosity of 50.4%at elevated temperature(1200°C).These results are attributed to the significant role of added Li2CO3 as sintering additive,where the volatilization of intergranular glassy phase occurs during sintering process.Therefore,porous Si3N4 ceramics with desired mechanical property prepared by altering the addition of sintering additives demonstrate their great potential as a promising candidate for high temperature applications.
基金The US AMRDEC grant No.W911NF-16-2-0069“Enhanced Absorption in Stopped-Light Photonic Nanostructures:Applications to Efficient Sensing”EU LASERLAB-EUROPE(grant agreement No.871124Horizon 2020 research and innovation programme)projects are acknowleged for the financial support.D.G.acknowledges the financial support from the European Social Fund(project No 09.3.3-LMT-K712-17-0016)under grant agreement with the Research Council of Lithuania(LMTLT).
文摘The current study is directed to the rapidly developing field of inorganic material 3D object production at nano-/micro scale.The fabrication method includes laser lithography of hybrid organic-inorganic materials with subsequent heat treatment leading to a variety of crystalline phases in 3D structures.In this work,it was examined a series of organometallic polymer precursors with different silicon(Si)and zirconium(Zr)molar ratios,ranging from 9:1 to 5:5,prepared via sol-gel method.All mixtures were examined for perspective to be used in 3D laser manufacturing by fabricating nano-and micro-feature sized structures.Their spatial downscaling and surface morphology were evaluated depending on chemical composition and crystallographic phase.The appearance of a crystalline phase was proven using single-crystal X-ray diffraction analysis,which revealed a lower crystallization temperature for microstructures compared to bulk materials.Fabricated 3D objects retained a complex geometry without any distortion after heat treatment up to 1400℃.Under the proper conditions,a wide variety of crystalline phases as well as zircon(ZrSiO_(4)-a highly stable material)can be observed.In addition,the highest new record of achieved resolution below 60 nm has been reached.The proposed preparation protocol can be used to manufacture micro/nano-devices with high precision and resistance to high temperature and aggressive environment.
文摘Silicon carbide (SiC) ceramics have excellent properties and widely used for high temperature applications. So far, joining techniques have been applied to fabricate large SiC ceramics with complicated shapes. In this work, the additive manufacturing (AM) technique was examined to fabricated SiC ceramics with complicated hollow structures using the Fused Deposition Modeling (FDM) type 3D-printer. To mold the hollow structure for the applications such as heat exchangers, the “support-less” condition must be achieved. Thus, extruded SiC-phenol resin compounds must be cured immediately after molding to keep the molded shapes. To increase the thermal conductivity of the SiC compounds, the combinations of commercial SiC powders with different average diameters were examined for increasing the volume fraction of SiC particles to the phenol resin. SiC compounds with optimized rheological properties for the modified FDM-type 3D-printer were successfully obtained.
文摘The melting temperature and critical transition temperature Tc of YBa2Cu3O7-δ with deferent content additives of PbO and BaPbO3 were studied. When PbO was doped in YBa2Cu3O7-δ, the melting temperature of YBa2Cu3O7-δ was reduced, however its superconductivity was weakened. From the XRD pattern of the sintered mixture of YBa2Cu3O7-δ and PbO, it was known that there was a reaction between YBa2Cu3O7-δ and PbO, and the product was BaPbO3. Hence different contents of BaPbO3 (10mass%, 20mass% and 30mass%) were added in YBa2Cu3O7-δ. It was proved that there were no reactions between YBa2Cu3O7-δ and BaPbO3. And the superconductivity of the mixtures was much better than that of the samples with PbO additive.
基金the National Natural Science Foundation of China(No.51902036,51702138,22075115)Natural Science Foundation of Chongqing Science&Technology Commission(No.cstc2019jcyj-msxm1407)+4 种基金Natural Science Foundation of Chongqing Technology and Business University(No.1952009)the Venture&Innovation Support Program for Chongqing Overseas Returnees(Grant No.CX2018129)the Science and Technology Research Program of Chongqing Municipal Education Commission(Grant No.KJQN201900826 and KJQN201800808)the Innovation Group of New Technologies for Industrial Pollution Control of Chongqing Education Commission(Grant No.CXQT19023)Key Disciplines of Chemical Engineering and Technology in Chongqing Colleges and Universities during the 13th Five Year Plan provided the financial support.
文摘Zinc metal batteries have been considered as a promising candidate for next-generation batteries due to their high safety and low cost.However,their practical applications are severely hampered by the poor cyclability that caused by the undesired dendrite growth of metallic Zn.Herein,Ti_(3)C_(2)T_(x) MXene was first used as electrolyte additive to facilitate the uniform Zn deposition by controlling the nucleation and growth process of Zn.Such MXene additives can not only be absorbed on Zn foil to induce uniform initial Zn deposition via providing abundant zincophilic-O groups and subsequently participate in the formation of robust solid-electrolyte interface film,but also accelerate ion transportation by reducing the Zn^(2+) concentration gradient at the electrode/electrolyte interface.Consequently,MXene-containing electrolyte realizes dendrite-free Zn plating/striping with high Coulombic efficiency(99.7%)and superior reversibility(stably up to 1180 cycles).When applied in full cell,the Zn-V_(2)O_(5)cell also delivers significantly improved cycling performances.This work provides a facile yet effective method for developing reversible zinc metal batteries.
文摘Nanocrystalline TiO2 was prepared by high frequency plasma chemical vapor deposition (HF-PCVD). The effects of additive AlCl3 on crystal phase, particle size and microstructurai parameters of TiO2 nanocrystallites were investigated by X-ray diffraction(XRD) and transmission electron microscopy (TEM). The nanocrystallites obtained experimentally are mixture of anatase and rutile, the uniform diameters of particles are about 30 nm. The phase transformation from anatase to rutile was accelerated by AlCl3, and rutile content is increased from 26.7 wt pct to 53.6 wt pct with increasing of addition of AlCl3 from 0.0 wt pct to 5.0 wt pct. The particle size is reduced and the size distribution becomes very narrow. The crystal lattice constants have the trend to decrease, and celi volumes appear as shrinkable.
