On Switching of a Flip-Flop Jet Nozzle with Double Ports by Single-Port Control

This research deals with the oscillation mechanism of a flip-flop jet nozzle with a connecting tube, based on the measurements of pressures and velocities in the connecting tube and inside the nozzle. The measurements are carried out varying: 1) the inside diameter d of the connecting tube;2) the length L of the connecting tube and 3) the jet velocity VPN from a primary-nozzle exit. We assume that the jet switches when a time integral reaches a certain value. At first, as the time integral, we introduce the accumulated flow work of pressure, namely, the time integral of mass flux through a connecting tube into the jet-reattaching wall from the opposite jet-un-reattaching wall. Under the assumption, the trace of pressure difference between both the ends of the connecting tube is simply modeled on the basis of measurements, and the flow velocity in the connecting tube is computed as incompressible flow. Second, in order to discuss the physics of the accumulated flow work further, we conduct another experiment in single-port control where the inflow from the control port on the jet-reattaching wall is forcibly controlled and the other control port on the opposite jet-un-reattaching wall is sealed, instead of the experiment in regular jet’s oscillation using the ordinary nozzle with two control ports in connection. As a result, it is found that the accumulated flow work is adequate to determine the dominant jet- oscillation frequency. In the experiment in single-port control, the accumulated flow work of the inflow until the jet’s switching well agrees with that in regular jet’s oscillation using the ordinary nozzle.

The Acoustic Performance of 3D Printed Multiple Jet Nozzles with DifferentConfigurations

This work investigated multiple jet nozzles with various geometrical shape,number of exits,and material on reducing noise radiated from jet flows.Nozzles are categorized in two groups with few and many exit numbers,each with various exit shapes,slot and circular,and geometry.Firstly,nozzles are designed and then fabricated by a 3D printer,Form Labs,Form2USA,with polymeric resin.Also,the nozzle with the most noise reduction made of stainless steel.Noise and air thrust were measured at three air pressure gauges,3,5,7 BAR and directions from nozzle apex,30°,90°,135°.Nozzles with slot exit shape made of both plastic and stainless steel revealed the most noise reduction among all nozzles with few exit numbers,nearly 11–14 dB(A)and 11.5–15 dB(A),respectively.On average,slotted nozzle noise reduction was nearly 5–6 dB(A)more than finned nozzle.However,nozzles with more exit numbers,finned and finned-central exit,illustrated much more noise reduction than nozzles with few exit numbers,by almost 16–18 dB(A),they represented similar sound.All tested nozzles and open pipe demonstrated equal air thrust at each pressure gauges.The nozzles with slotted exit shape,either plastic or stainless steel,can provide reasonable noise reduction in comparison to other configuration with few exit numbers.In contrast,nozzles with more exit numbers demonstrated the most noise reduction.

Effects of Variable Jet Nozzle Angles on Cross-Flow Suppression and Heat Transfer Enhancement of Swirl Chamber

This paper investigated the effects of variable jetting nozzle angles on the cross-flow suppression and heat transfer enhancement of swirl cooling in gas turbine leading edge. The swirl chamber with vertical jet nozzles was set as the baseline, and its flow fields and heat transfer characteristics were analyzed by 3D steady state Reynolds-averaged numerical methods to reveal the mechanism of cross-flow weakening the downstream jets and heat transfer. On this basis, the flow structure on different cross sections and heat transfer characteristics of swirl chamber with variable jetting nozzle angels were compared with the baseline swirl chamber. The results indicated that for the baseline swirl chamber the circumferential velocity gradually decreased and the axial velocity gradually increased, and the cross-flow gradually formed. The cross-flow deflected the downstream jets and drawn them to the center of the chamber, thus weakening the heat transfer. For swirl chamber with variable jetting nozzle angles, the air axial velocity is axial upstream, opposite to the mainstream, so that the impact effects of cross-flow on the jets were reduced, and the heat transfer was enhanced. Furthermore, with the increase of axial velocity along the swirl chamber, the jetting nozzle angle also gradually increased, as well as the effect of cross-flow suppression, which formed a relative balance. For all swirl chambers with variable jet nozzle angles, the thermal performance factors were all larger than 1, which indicated the heat transfer was enhanced with less friction increment.

Passive Control of Turbulent Jet Flow with Wedged Nozzle

Turbulent flow field of the free jet with circular nozzle and wedged nozzles is measured using hot wire anemometry with resolution higher than the smallest turbulence time scale. Wavelet analysis is employed to perform multi-scale decomposition of instantaneous turbulence fluctuating velocity signals, and the energy distribution of the turbulent multi-scale eddy structures over scales is studied using wavelet coefficients. Investigation of the multi-scale eddy structures of circular jet and various wedged jets reveals the transport of the energy of these wedged jets in the space from the axis to the side of the jet, as compared with the circular jet. Furthermore, not only the eddy structures at the wedge tines in the near field are crashed, but also the interactions such as eddy structure union and entrainment take place at different longitudinal and normal locations along with the development of the jets because of the existence of wedges.

Three-Dimensional Rainbow Schlieren Measurements in Underexpanded Sonic Jets from Axisymmetric Convergent Nozzles

The rainbow schlieren deflectometry has been combined with the computed tomography to obtain three-dimensional density fields of shock containing free jets and we call the method the schlieren CT. Experiments on the schlieren CT have been performed at a nozzle pressure ratio of 4.0 by using an axisymmetric convergent nozzle with an inner diameter of 10 mm at the exit where the nozzle was operated at an underexpanded condition. Multidirectional rainbow schlieren pictures of an underexpanded sonic jet can be acquired by rotating the nozzle about its longitudinal axis in equal angular intervals and the three-dimensional density fields are reconstructed by the schlieren CT. The validity of the schlieren CT is verified by a comparison with the density fields reconstructed by the Abel inversion method. As a result, it is found that excellent quantitative agreement is reached between the three-dimensional jet density fields reconstructed from both methods.

THE PERFORMANCES OF HIGH PRESSURE JET OF PURE WATER AND POLYMER SOLUTION WITH CONICAL NOZZLE

In this paper, the effects of polymer additives and nozzle shape on the proper- ties of high pressure water jet discharging into the air are investigated by theory and experiments. Criteria of judging the jet quality are put forward. And, a method that can be used in analysing the fluid flow within the nozzle is developed. Then, the calculated results are compared with the experiments that we carried out; it is shown that the degree of agreement between the two is good. At last, the mechanism to improve on the jet quality with polymer additives is discussed.

Experimental study on double-stage on-line jet mixing apparatus

With the accelerated development of agricultural intelligence and mechanization,the traditional premixed pesticide mixing method has been unable to meet people’s needs for safe,environmental and efficient agricultural production.Therefore,an in-depth study on a variety of new pesticide mixing methods has been conducted at home and abroad.The single-stage on-line jet mixing method has been increasingly used because of its advantages of safety and high efficiency,which,however,proved to have some disadvantages such as difficulty in controlling the pesticide mixing ratio and poor mixing uniformity.In this experiment,a set of double-stage online jet mixing apparatus was designed to solve some shortcomings of single-stage online jet mixing apparatus,and the influence of jet nozzle parameters in the main jet mixing apparatus and the radiation flow mixing apparatus on the final pesticide mixing effect were studied for this apparatus,and the most appropriate jet nozzle parameters were selected.