At Baoshan Iron ＆ Steel Co., Ltd., comer cracks of boron containing LCAK steel slabs had caused remarkable quality loss and mass flow disorder. With the help of fractography and thermodynamics analysis, the embrittle...At Baoshan Iron ＆ Steel Co., Ltd., comer cracks of boron containing LCAK steel slabs had caused remarkable quality loss and mass flow disorder. With the help of fractography and thermodynamics analysis, the embrittlement mechanism of this steel grade was studied and the results are as follows： 1 The transformation from 3＇ to a starts at the austenite grain boundaries and a layer of thin ferrite film gradually forms around the austenite grains. Strain concentration will preferentially start inside the ferrite phase when the stress accumulates to a certain level. 2 The coarse BN particles acceleratedly precipitated at the γ/α interfaces further deteriorate the ductility of the ferrite film, and brittleness results in strain concentration and microvoid coalescence inside the ferrite film. Therefore the austenite grain boundaries are prone to intergranular failure. 3 The stoichiometry among Al, N and B is a very important factor influencing the hot ductility of this steel grade. By controling the B-to-N atomic ratio to above 1, all N can be fixed by B instead of A1. Thus coarsegrained steel is available and fewer grain boundaries and higher ductility can reduce the risk of comer cracks. （4） By adjusting the B-to-N atomic ratio,Baoshan Iron ＆ Steel Co.,Ltd. successfully reduced the number of cracks to nearly one tenth of that in the past and the hot tensile tests confirmed remarkable improvement in the hot ductility of this steel.展开更多
The behavior of non-metallic inclusions in LCAK （low carbon aluminum killed） steel produced by BOF （basic oxygen furnace）-LF （ladle furnace） refining-FTSC （flexible thin slab continuous caster） production rout...The behavior of non-metallic inclusions in LCAK （low carbon aluminum killed） steel produced by BOF （basic oxygen furnace）-LF （ladle furnace） refining-FTSC （flexible thin slab continuous caster） production route was investigated. The results showed that, LF refining for LCAK steel could decrease the wT[o] significantly, and the inclusions were modified by Ca treatment, which prevented nozzle clogging efficiently. However, owing to the unstable casting condition in the earlier stage of casting, a severe reoxidation occurred, accompanied with mold slag entrapment. The transformation of non-metallic inclusions during the steelmaking process was Al2O3→MgO→Al2O3 type inclusion→MgO-Al2O3 O3-CaO type inclusion with a CaS ring, and the mechanism of the transformation was pro posed and discussed via thermodynamic and kinetic analysis. Besides, to avoid CaS precipitation, the product of W[Al] ×w3[S] in steel should be less than 2.0 × 10 10 at 1873 K, which remands higher desulfurization ratio during LF refining.展开更多
文摘At Baoshan Iron ＆ Steel Co., Ltd., comer cracks of boron containing LCAK steel slabs had caused remarkable quality loss and mass flow disorder. With the help of fractography and thermodynamics analysis, the embrittlement mechanism of this steel grade was studied and the results are as follows： 1 The transformation from 3＇ to a starts at the austenite grain boundaries and a layer of thin ferrite film gradually forms around the austenite grains. Strain concentration will preferentially start inside the ferrite phase when the stress accumulates to a certain level. 2 The coarse BN particles acceleratedly precipitated at the γ/α interfaces further deteriorate the ductility of the ferrite film, and brittleness results in strain concentration and microvoid coalescence inside the ferrite film. Therefore the austenite grain boundaries are prone to intergranular failure. 3 The stoichiometry among Al, N and B is a very important factor influencing the hot ductility of this steel grade. By controling the B-to-N atomic ratio to above 1, all N can be fixed by B instead of A1. Thus coarsegrained steel is available and fewer grain boundaries and higher ductility can reduce the risk of comer cracks. （4） By adjusting the B-to-N atomic ratio,Baoshan Iron ＆ Steel Co.,Ltd. successfully reduced the number of cracks to nearly one tenth of that in the past and the hot tensile tests confirmed remarkable improvement in the hot ductility of this steel.
基金Item Sponsored by National Key Technology Research and Development Programin 11th Five-Year Plan of China(2006BAE03A13)
文摘The behavior of non-metallic inclusions in LCAK （low carbon aluminum killed） steel produced by BOF （basic oxygen furnace）-LF （ladle furnace） refining-FTSC （flexible thin slab continuous caster） production route was investigated. The results showed that, LF refining for LCAK steel could decrease the wT[o] significantly, and the inclusions were modified by Ca treatment, which prevented nozzle clogging efficiently. However, owing to the unstable casting condition in the earlier stage of casting, a severe reoxidation occurred, accompanied with mold slag entrapment. The transformation of non-metallic inclusions during the steelmaking process was Al2O3→MgO→Al2O3 type inclusion→MgO-Al2O3 O3-CaO type inclusion with a CaS ring, and the mechanism of the transformation was pro posed and discussed via thermodynamic and kinetic analysis. Besides, to avoid CaS precipitation, the product of W[Al] ×w3[S] in steel should be less than 2.0 × 10 10 at 1873 K, which remands higher desulfurization ratio during LF refining.
