The dielectric properties and phase transition characteristics of La2O3- and Sb2O3-doped barium strontium titanate ceramics prepared by solid state route were investigated. The microstructure was identified by X-ray d...The dielectric properties and phase transition characteristics of La2O3- and Sb2O3-doped barium strontium titanate ceramics prepared by solid state route were investigated. The microstructure was identified by X-ray diffraction method and scanning electron microscope was also employed to observe the surface morphologies. It is found that （La,Sb）-codoped barium strontium titanate ceramics exhibit typical perovskite structure and the average grain size decreases dramatically with increasing the content of Sb2O3. Both La3＋ ions and Sb3＋ ions occupy the A-sites in perovskite lattice. The dielectric constant and dielectric loss of barium strontium titanate based ceramics are obviously influenced by La2O3 as well as Sb2O3 addition content. The tetragonal-cubic phase transition of La2O3 modified barium strontium titanate ceramics is of second order and the Curie temperature shifts to lower value with increasing the La2O3 doping content. The phase transition of （La,Sb）-codoped barium strontium titanate ceramics diffuses and the deviation from Curie-Weiss law becomes more obvious with the increase in Sb2O3 concentration. The temperature corresponding to the dielectric constant maximum of （La,Sb）-codoped barium strontium titanate ceramics decreases with increasing the Sb2O3 content, which is attributed to the replacement of host ions by the Sb3＋ ions.展开更多
A near infrared to visible blue, green, and red upconversion luminescence in a Tb^3＋-doped CaO-Al2O3-SiO2 glass was studied, which was excited using 800 nm femtosecond laser irradiation. The upconversion luminescence...A near infrared to visible blue, green, and red upconversion luminescence in a Tb^3＋-doped CaO-Al2O3-SiO2 glass was studied, which was excited using 800 nm femtosecond laser irradiation. The upconversion luminescence was attributed to ^5D3→^7F5, ^5D3→^7F4, ^5D3→^7F3, ^5D4→^7F6, ^5D4→^7F5, ^5D4→^7F4, and ^5D4→^7F3 transitions of Tb^3＋. The relationship between upconversion luminescence intensity and the pump power indicated that a three-photon simultaneous absorption process was dominant in this upconversion luminescence. The intense red, green, and blue upconversion luminescence of Tb^3＋-doped CaO-Al2O3-SiO2 glass may be potentially useful in developing three-dimensional display applications.展开更多
In this paper,La（3）-doped Nano-TiO2（La（3）-TiO2） was synthesized via hydrothermal process.Structure and optical properties of the synthesized samples were characterized via XRD,FT-IR,DRS,etc.The results showed th...In this paper,La（3）-doped Nano-TiO2（La（3）-TiO2） was synthesized via hydrothermal process.Structure and optical properties of the synthesized samples were characterized via XRD,FT-IR,DRS,etc.The results showed that the phase transformation of TiO2 from anatase to rutile was effectively prevented by La（3）-doping,which improved the thermal stability of anatase,and also suppressed particle aggregation and grain growth of TiO2.The formation of Ti-O-La bond promoted UV absorption intensity of TiO2,and provoked red shift of absorbed light.And the spectra response range of TiO2 was extended significantly to visible light by La（3）-doping,then photocatalytic performance was improved effectively.Compared with pure nano-TiO2,the performance of La（3）-TiO2 which photocatalyticly degraded methyl orange was increased significantly.展开更多
The relationship between composition and the electric mechanical properties for La2O3-doped lead niobium stibium zirconate titanate(La2O3-doped PNSZT) piezoelectric ceramics,in which there are tetragonal and rhombohed...The relationship between composition and the electric mechanical properties for La2O3-doped lead niobium stibium zirconate titanate(La2O3-doped PNSZT) piezoelectric ceramics,in which there are tetragonal and rhombohedral coexistent phases, was studied. A series of piezoelectric ceramics with good properties was obtained, having dielectric constants (ε= 1500 ~ 2500), plane electromechanical coupling factor(Kp = 0.45 ~ 0.65), mechanical quality factor( Qm = 500 ~ 1600). These materials are used for making ultrasonic sensor and filter, and marine acoustic launching and receiving device, and so on. It has been explored that the influence of composition on the lattice constant and phase composition of La2O3-doped PNSZT piezoelectric ceramics by XRD(X-ray diffraction) . The character of dielectric constant changing of La2O3-doped PNSZT piezoelectric ceramics before polarization and after polarization was studied. The affecting mechanism about composition on the electric machine properties of phase coexistent La2O3-doped PNSZT piezoelectric ceramics was analyzed and discussed.展开更多
The Sm^（3＋）-doped SrO-Al2O3-SiO2（SAS） glass-ceramics with excellent luminescence properties were prepared by batch melting and heat treatment. The crystallization behavior and luminescent properties of the glass-...The Sm^（3＋）-doped SrO-Al2O3-SiO2（SAS） glass-ceramics with excellent luminescence properties were prepared by batch melting and heat treatment. The crystallization behavior and luminescent properties of the glass-ceramics were investigated by DTA, XRD, SEM and luminescence spectroscopy. The results indicate that the crystal phase precipitated in this system is monocelsian（SrAl2Si2O） and with the increase of nucleation/crystallization temperature, the crystallite increases from 66 % to 79 %. The Sm（3＋）-doped SAS glass-ceramics emit green, orange and red lights centered at 565, 605, 650 and 715 nm under the excitation of 475 nm blue light which can be assigned to the 4 G5/2→6 Hj/2（j=5, 7, 9, 11） transitions ofSm^（3＋）, respectively. Besides, by increasing the crystallization temperature or the concentration ofSm^（3＋）, the emission lights of the samples located at 565, 605 and 650 nm are intensified significantly. The present results demonstrate that theSm^（3＋）-doped SAS glassceramics are promising luminescence materials for white LED devices by fine controlling and combining of these three green, orange and red lights in appropriate proportion.展开更多
Physical vapor deposition(PVD)can be used to produce high-quality Gd_(2)O_(3)-doped CeO2(GDC)films.Among various PVD methods,reactive sputtering provides unique benefits,such as high deposition rates and easy upscalin...Physical vapor deposition(PVD)can be used to produce high-quality Gd_(2)O_(3)-doped CeO2(GDC)films.Among various PVD methods,reactive sputtering provides unique benefits,such as high deposition rates and easy upscaling for industrial applications.GDC thin films were successfully fabricated through reactive sputtering using a Gd_(0.2)Ce_(0.8)(at%)metallic target,and their application in solid oxide fuel cells,such as buffer layers between yttria-stabilized zirconia(YSZ)/La0.6Sr0.4Co0.2Fe0.8O_(3−δ)and as sublayers in the steel/coating system,was evaluated.First,the direct current(DC)reactive-sputtering behavior of the GdCe metallic target was determined.Then,the GDC films were deposited on NiO-YSZ/YSZ half-cells to investigate the influence of oxygen flow rate on the quality of annealed GDC films.The results demonstrated that reactive sputtering can be used to prepare thin and dense GDC buffer layers without high-temperature sintering.Furthermore,the cells with a sputtered GDC buffer layer showed better electrochemical performance than those with a screen-printed GDC buffer layer.In addition,the insertion of a GDC sublayer between the SUS441 interconnects and the Mn-Co spinel coatings contributed to the reduction of the oxidation rate for SUS441 at operating temperatures,according to the area-specific resistance tests.展开更多
Various solid electrolytes,such as sulfides(10^-3-10^-2 S cm^-1)and oxides(10^-4–10^-3 S cm^-1)are explored and developed to solve the safety problems in commercial Li-ion batteries using liquid flammable electrolyte...Various solid electrolytes,such as sulfides(10^-3-10^-2 S cm^-1)and oxides(10^-4–10^-3 S cm^-1)are explored and developed to solve the safety problems in commercial Li-ion batteries using liquid flammable electrolytes.Metallic Li anode is required for pursuing high power density(>300 Wh kg^-1)for solid-state batteries[1,2].展开更多
Y2O3-doped Mo secondary emitters were prepared by liquid-liquid doping and solid-solid doping,respectively.The back-scattered scanning observation result indicates that the emitter prepared by liquid-liquid doping has...Y2O3-doped Mo secondary emitters were prepared by liquid-liquid doping and solid-solid doping,respectively.The back-scattered scanning observation result indicates that the emitter prepared by liquid-liquid doping has fine microstructure whereas that prepared by solid-solid doping has large grain size.Y2O3-doped Mo emitter with small grain size prepared by liquid-liquid doping exhibits high emission property,i.e.,the secondary electron yield can get to 5.24,about 1.7 times that prepared by solid-solid doping.Moreover,Y2O3-doped Mo emitter exhibits the best emission performance among La2O3-doped Mo,Y2O3-doped Mo, Gd2O3-doped Mo and Ce2O3-doped Mo emitters due to the largest penetration depth of primary electrons and escape depth of secondary electrons in this emitter.The secondary emission of the emitter with small grain size can be explained by reflection emission model and transmission emission model,whereas only transmission emission exists in the emitter with large grain size.展开更多
采用光电子能谱分析方法对掺杂 L a2 O3的 Mo粉的性能进行了研究。结果表明 :掺杂 L a(NO3) 3的 Mo O2 粉经过还原处理后 ,Mo粉表面的纳米 L a2 O3微粒可以减小 Mo基体的特征能量损失峰 ,增加 Mo3d光电子谱峰强度 ;由于纳米 L a2 O3粒...采用光电子能谱分析方法对掺杂 L a2 O3的 Mo粉的性能进行了研究。结果表明 :掺杂 L a(NO3) 3的 Mo O2 粉经过还原处理后 ,Mo粉表面的纳米 L a2 O3微粒可以减小 Mo基体的特征能量损失峰 ,增加 Mo3d光电子谱峰强度 ;由于纳米 L a2 O3粒子在金属 Mo的表面及周围对 Mo起到包埋效应 ,减小了 Mo与大气的接触面积 ,从而使展开更多
A new stearic acid method(SAM) has been used to prepare ultrafine K2La2Ti3O10 nanocrystalline. Each state of synthesis process was followed by the use of FT IR analysis. The resulting materials have been characterized...A new stearic acid method(SAM) has been used to prepare ultrafine K2La2Ti3O10 nanocrystalline. Each state of synthesis process was followed by the use of FT IR analysis. The resulting materials have been characterized by means of XRD, TEM, BET surface area analysis. The acid exchanging property of the obtained product was also studied. The experimental results showed that comparing with the product of traditional solid state reaction, the particle size of the K2La2Ti3O10 synthesized by SAM is greatly reduced, BET surface area is high(more than 11.83m2· g- 1) and has different acid exchanging properties. It can be easily exfoliated in 2mol· L- 1 HNO3 solution.展开更多
基金Project (11KJB430007) supported by the University Natural Science Research Program of Jiangsu Province, ChinaProject supported by the Priority Academic Program Development of Jiangsu Higher Education Institutions, China
文摘The dielectric properties and phase transition characteristics of La2O3- and Sb2O3-doped barium strontium titanate ceramics prepared by solid state route were investigated. The microstructure was identified by X-ray diffraction method and scanning electron microscope was also employed to observe the surface morphologies. It is found that （La,Sb）-codoped barium strontium titanate ceramics exhibit typical perovskite structure and the average grain size decreases dramatically with increasing the content of Sb2O3. Both La3＋ ions and Sb3＋ ions occupy the A-sites in perovskite lattice. The dielectric constant and dielectric loss of barium strontium titanate based ceramics are obviously influenced by La2O3 as well as Sb2O3 addition content. The tetragonal-cubic phase transition of La2O3 modified barium strontium titanate ceramics is of second order and the Curie temperature shifts to lower value with increasing the La2O3 doping content. The phase transition of （La,Sb）-codoped barium strontium titanate ceramics diffuses and the deviation from Curie-Weiss law becomes more obvious with the increase in Sb2O3 concentration. The temperature corresponding to the dielectric constant maximum of （La,Sb）-codoped barium strontium titanate ceramics decreases with increasing the Sb2O3 content, which is attributed to the replacement of host ions by the Sb3＋ ions.
基金supported by the Education Department of Zhejiang Province (20050359)
文摘A near infrared to visible blue, green, and red upconversion luminescence in a Tb^3＋-doped CaO-Al2O3-SiO2 glass was studied, which was excited using 800 nm femtosecond laser irradiation. The upconversion luminescence was attributed to ^5D3→^7F5, ^5D3→^7F4, ^5D3→^7F3, ^5D4→^7F6, ^5D4→^7F5, ^5D4→^7F4, and ^5D4→^7F3 transitions of Tb^3＋. The relationship between upconversion luminescence intensity and the pump power indicated that a three-photon simultaneous absorption process was dominant in this upconversion luminescence. The intense red, green, and blue upconversion luminescence of Tb^3＋-doped CaO-Al2O3-SiO2 glass may be potentially useful in developing three-dimensional display applications.
基金Supported by Fujian High-tech Project Foundation (No 2004H008)
文摘In this paper,La（3）-doped Nano-TiO2（La（3）-TiO2） was synthesized via hydrothermal process.Structure and optical properties of the synthesized samples were characterized via XRD,FT-IR,DRS,etc.The results showed that the phase transformation of TiO2 from anatase to rutile was effectively prevented by La（3）-doping,which improved the thermal stability of anatase,and also suppressed particle aggregation and grain growth of TiO2.The formation of Ti-O-La bond promoted UV absorption intensity of TiO2,and provoked red shift of absorbed light.And the spectra response range of TiO2 was extended significantly to visible light by La（3）-doping,then photocatalytic performance was improved effectively.Compared with pure nano-TiO2,the performance of La（3）-TiO2 which photocatalyticly degraded methyl orange was increased significantly.
文摘The relationship between composition and the electric mechanical properties for La2O3-doped lead niobium stibium zirconate titanate(La2O3-doped PNSZT) piezoelectric ceramics,in which there are tetragonal and rhombohedral coexistent phases, was studied. A series of piezoelectric ceramics with good properties was obtained, having dielectric constants (ε= 1500 ~ 2500), plane electromechanical coupling factor(Kp = 0.45 ~ 0.65), mechanical quality factor( Qm = 500 ~ 1600). These materials are used for making ultrasonic sensor and filter, and marine acoustic launching and receiving device, and so on. It has been explored that the influence of composition on the lattice constant and phase composition of La2O3-doped PNSZT piezoelectric ceramics by XRD(X-ray diffraction) . The character of dielectric constant changing of La2O3-doped PNSZT piezoelectric ceramics before polarization and after polarization was studied. The affecting mechanism about composition on the electric machine properties of phase coexistent La2O3-doped PNSZT piezoelectric ceramics was analyzed and discussed.
基金Funded by the National Natural Science Foundation of China(No.5137217)Hubei Province Foreign Science and Technology Project(No.2016AHB027)Science and Technology Planning Project of Hubei Province(No.2014BAA136)
文摘The Sm^（3＋）-doped SrO-Al2O3-SiO2（SAS） glass-ceramics with excellent luminescence properties were prepared by batch melting and heat treatment. The crystallization behavior and luminescent properties of the glass-ceramics were investigated by DTA, XRD, SEM and luminescence spectroscopy. The results indicate that the crystal phase precipitated in this system is monocelsian（SrAl2Si2O） and with the increase of nucleation/crystallization temperature, the crystallite increases from 66 % to 79 %. The Sm（3＋）-doped SAS glass-ceramics emit green, orange and red lights centered at 565, 605, 650 and 715 nm under the excitation of 475 nm blue light which can be assigned to the 4 G5/2→6 Hj/2（j=5, 7, 9, 11） transitions ofSm^（3＋）, respectively. Besides, by increasing the crystallization temperature or the concentration ofSm^（3＋）, the emission lights of the samples located at 565, 605 and 650 nm are intensified significantly. The present results demonstrate that theSm^（3＋）-doped SAS glassceramics are promising luminescence materials for white LED devices by fine controlling and combining of these three green, orange and red lights in appropriate proportion.
基金financially supported by the National Key R&D Program of China (No. 2018YFB1502203-1)the Guangdong Basic and Applied Basic Research Foundation (No. 2021B1515120087)the Stable Supporting Fund of Shenzhen, China (No. GXWD20201230155427003-202007 28114835006)
文摘Physical vapor deposition(PVD)can be used to produce high-quality Gd_(2)O_(3)-doped CeO2(GDC)films.Among various PVD methods,reactive sputtering provides unique benefits,such as high deposition rates and easy upscaling for industrial applications.GDC thin films were successfully fabricated through reactive sputtering using a Gd_(0.2)Ce_(0.8)(at%)metallic target,and their application in solid oxide fuel cells,such as buffer layers between yttria-stabilized zirconia(YSZ)/La0.6Sr0.4Co0.2Fe0.8O_(3−δ)and as sublayers in the steel/coating system,was evaluated.First,the direct current(DC)reactive-sputtering behavior of the GdCe metallic target was determined.Then,the GDC films were deposited on NiO-YSZ/YSZ half-cells to investigate the influence of oxygen flow rate on the quality of annealed GDC films.The results demonstrated that reactive sputtering can be used to prepare thin and dense GDC buffer layers without high-temperature sintering.Furthermore,the cells with a sputtered GDC buffer layer showed better electrochemical performance than those with a screen-printed GDC buffer layer.In addition,the insertion of a GDC sublayer between the SUS441 interconnects and the Mn-Co spinel coatings contributed to the reduction of the oxidation rate for SUS441 at operating temperatures,according to the area-specific resistance tests.
基金financially supported by Ganfeng Lithium Co., Ltd.
文摘Various solid electrolytes,such as sulfides(10^-3-10^-2 S cm^-1)and oxides(10^-4–10^-3 S cm^-1)are explored and developed to solve the safety problems in commercial Li-ion batteries using liquid flammable electrolytes.Metallic Li anode is required for pursuing high power density(>300 Wh kg^-1)for solid-state batteries[1,2].
基金Projects(2006AA03Z524,2008AA031001)supported by the National Hi-tech Research and Development Program of ChinaProject(50801001)supported by the National Natural Foundation of China
文摘Y2O3-doped Mo secondary emitters were prepared by liquid-liquid doping and solid-solid doping,respectively.The back-scattered scanning observation result indicates that the emitter prepared by liquid-liquid doping has fine microstructure whereas that prepared by solid-solid doping has large grain size.Y2O3-doped Mo emitter with small grain size prepared by liquid-liquid doping exhibits high emission property,i.e.,the secondary electron yield can get to 5.24,about 1.7 times that prepared by solid-solid doping.Moreover,Y2O3-doped Mo emitter exhibits the best emission performance among La2O3-doped Mo,Y2O3-doped Mo, Gd2O3-doped Mo and Ce2O3-doped Mo emitters due to the largest penetration depth of primary electrons and escape depth of secondary electrons in this emitter.The secondary emission of the emitter with small grain size can be explained by reflection emission model and transmission emission model,whereas only transmission emission exists in the emitter with large grain size.
文摘A new stearic acid method(SAM) has been used to prepare ultrafine K2La2Ti3O10 nanocrystalline. Each state of synthesis process was followed by the use of FT IR analysis. The resulting materials have been characterized by means of XRD, TEM, BET surface area analysis. The acid exchanging property of the obtained product was also studied. The experimental results showed that comparing with the product of traditional solid state reaction, the particle size of the K2La2Ti3O10 synthesized by SAM is greatly reduced, BET surface area is high(more than 11.83m2· g- 1) and has different acid exchanging properties. It can be easily exfoliated in 2mol· L- 1 HNO3 solution.
