A 2D woven graphite fibers reinforced aluminum matrix composite with 50%Grf (volume fraction) was fabricated by the squeeze-casting technology, and its microstructure and mechanical properties were investigated. The r...A 2D woven graphite fibers reinforced aluminum matrix composite with 50%Grf (volume fraction) was fabricated by the squeeze-casting technology, and its microstructure and mechanical properties were investigated. The results show that the composite is dense, the graphite fibers are distributed uniformly in the composite. TEM observation indicates the bonding between fiber and matrix is good and little interfacial reaction is found in the Grf/Al composite. This is attributed to the better stability of graphite fiber and the fabrication process minimizing the contact time between fiber with matrix at high temperatures. The 2D woven Grf/Al composite exhibites better mechanical properties with tensile strength, bending strength and elastic modulus of 366.2, 519.7 and 110.7 GPa, respectively. SEM images suggeste that the fracture is irregular and some pulled-out fibers are found, which indicats that the high strength of fiber is not degraded.展开更多
In order to develop high strength,high damping and low density Al matrix composites,the Al/Zn composite bar samples with Zn mass fraction of 10%-40%were prepared by powder extrusion.The tensile strength and damping pr...In order to develop high strength,high damping and low density Al matrix composites,the Al/Zn composite bar samples with Zn mass fraction of 10%-40%were prepared by powder extrusion.The tensile strength and damping properties of the samples are improved by controlling both the Zn/Al diffusion degree and the precipitation of the interfacial phases.The results show that the tensile strength of the samples with Zn mass fraction of 10%-30%increases with the increases of both the Zn content and annealing temperature.When the Zn mass fraction increases to 40%,the tensile strength of the sample remains basically unchanged or decreases slightly,and the plasticity decreases gradually.Alloying of Al matrix and the formation of Zn/Al interface layer are mainly responsible for improving the strength of the annealed samples.The damping properties increase with the increases of both the Zn content and annealing temperature.The Zn/Al eutectoid lamella eliminates the detrimental effects on damping properties due to both alloying of the Al matrix and reduction of pure Zn in the Al matrix.The Al-30%Zn sample annealed at 350°C for 0.5 h has good comprehensive properties,including the tensile strength of 330 MPa,the elongation to failure of 10%and the room-temperature damping properties(tanθ)of 0.025.展开更多
文摘A 2D woven graphite fibers reinforced aluminum matrix composite with 50%Grf (volume fraction) was fabricated by the squeeze-casting technology, and its microstructure and mechanical properties were investigated. The results show that the composite is dense, the graphite fibers are distributed uniformly in the composite. TEM observation indicates the bonding between fiber and matrix is good and little interfacial reaction is found in the Grf/Al composite. This is attributed to the better stability of graphite fiber and the fabrication process minimizing the contact time between fiber with matrix at high temperatures. The 2D woven Grf/Al composite exhibites better mechanical properties with tensile strength, bending strength and elastic modulus of 366.2, 519.7 and 110.7 GPa, respectively. SEM images suggeste that the fracture is irregular and some pulled-out fibers are found, which indicats that the high strength of fiber is not degraded.
基金Project(2016YFB0300901)supported by the National Key Research and Development Program of China
文摘In order to develop high strength,high damping and low density Al matrix composites,the Al/Zn composite bar samples with Zn mass fraction of 10%-40%were prepared by powder extrusion.The tensile strength and damping properties of the samples are improved by controlling both the Zn/Al diffusion degree and the precipitation of the interfacial phases.The results show that the tensile strength of the samples with Zn mass fraction of 10%-30%increases with the increases of both the Zn content and annealing temperature.When the Zn mass fraction increases to 40%,the tensile strength of the sample remains basically unchanged or decreases slightly,and the plasticity decreases gradually.Alloying of Al matrix and the formation of Zn/Al interface layer are mainly responsible for improving the strength of the annealed samples.The damping properties increase with the increases of both the Zn content and annealing temperature.The Zn/Al eutectoid lamella eliminates the detrimental effects on damping properties due to both alloying of the Al matrix and reduction of pure Zn in the Al matrix.The Al-30%Zn sample annealed at 350°C for 0.5 h has good comprehensive properties,including the tensile strength of 330 MPa,the elongation to failure of 10%and the room-temperature damping properties(tanθ)of 0.025.
