Preparation and laser induced damage properties of rare earth doped BAS glass

Rare earth doped B2O3-Al2O3-SiO2 glass （RExBAS, x=5, 10, 20; RE=La, Sm） were prepared by solid state reaction method. Optical transmission spectra of such glass were characterized by ultraviolet spectrometers, and 1064 nm laser induced damage performance was investigated through the method of ＂1-on-1＂. The results indicated that there was a strong absorptive peak near 1064 nm in SmxBAS glass, the peak was enhanced with increasing x. While LaxBAS glass was transparent to 1064 nm laser, at the same time, the results of laser induced damage showed that the anti-laser induced damage performance of such glass was strengthened with the addition of rare earth oxide. Furthermore, the laser induced damage threshold （LIDT） of SmxBAS glass was significantly higher than that of LaxBAS glass. Consequently, Sm^3＋ doping was favor in the improvement of anti-laser induced damage performance for BAS glass.

Mechanism of micro-waviness induced KH_2PO_4 crystal laser damage and the corresponding vibration source

The low laser induced damage threshold of the KH2PO4 crystal seriously restricts the output power of inertial confinement fusion.The micro-waviness on the KH2PO4 surface processed by single point diamond turning has a significant influence on the damage threshold.In this paper,the influence of micro-waviness on the damage threshold of the KH2PO4 crystal and the chief sources introducing the micro-waviness are analysed based on the combination of the Fourier modal theory and the power spectrum density method.Research results indicate that among the sub-wavinesses with different characteristic spatial frequencies there exists the most dangerous frequency which greatly reduces the damage threshold,although it may not occupy the largest proportion in the original surface.The experimental damage threshold is basically consistent with the theoretical calculation.For the processing parameters used,the leading frequency of micro-waviness which causes the damage threshold to decrease is between 350-1 μm-1 and 30-1 μm-1,especially between 90-1 μm-1 and 200-1 μm-1.Based on the classification study of the time frequencies of microwaviness,we find that the axial vibration of the spindle is the chief source introducing the micro-waviness,nearly all the leading frequencies are related to the practical spindle frequency（about 6.68 Hz,400 r/min） and a special middle frequency（between 1.029 Hz and 1.143 Hz）.

Improvement of laser damage thresholds of fused silica by ultrasonic-assisted hydrofluoric acid etching

Polished fused silica samples were etched for different durations by using hydrofluoric（HF） acid solution with HF concentrations in an ultrasonic field. Surface and subsurface polishing residues and molecular structure parameters before and after the etching process were characterized by using a fluorescence microscope and infrared（IR） spectrometer, respectively. The laser induced damage thresholds（LIDTs） of the samples were measured by using pulsed nanosecond laser with wavelength of 355 nm. The results showed that surface and subsurface polishing residues can be effectively reduced by the acid etching process, and the LIDTs of fused silica are significantly improved. The etching effects increased with the increase of the HF concentration from 5 wt.% to 40 wt.%. The amount of polishing residues decreased with the increase of the etching duration and then kept stable. Simultaneously, with the increase of the etching time, the mechanical strength and molecular structure were improved.

Study of the near-field modulation property of microwaviness on a KH_2PO_4 crystal surface

The KH2PO4 crystal is a key component in optical systems of inertial confinement fusion （ICF）. The microwaviness on a KH2PO4 crystal surface is strongly related to its damage threshold which is a key parameter for application. To study the laser induced damage mechanism caused by microwaviness, in this paper the near-field modulation properties of microwaviness to the incident wave are discussed by the Fourier modal method. Research results indicate that the microwaviness on the machined surface will distort the incident wave and thus lead to non-uniform distribution of the light intensity inside the crystal; in a common range of microwaviness amplitude, the light intensity modulation degree increases about 0.03 whenever the microwaviness amplitude increases 10 nm; 1 order diffraction efficiencies are the key factors responsible for light intensity modulation inside the crystal; the light intensity modulation is just around the microwaviness in the form of an evanescent wave, not inside the crystal when the microwaviness period is below 0.712μm; light intensity modulation degree has two extreme points in microwaviness periods of 1.064μm and 1.6μm, remains unchanged between periods of 3μm and 150μm, and descends above the period of 150μm to 920μm.

Improvements in long-term output energy performance of Nd:glass regenerative amplifiers

Optical damages, which severely degrade the output energy performance of Nd:glass regenerative amplifiers, are discussed in detail in this paper. By a series of experiments, it has been confirmed that these damages result from laser-induced contamination. Based on this work, several improvements are made to boost output energy performance of the regenerative amplifier. The output energy of the regenerative amplifier after improvements declines 4% after 1000 h of operation, much less than it used to, 60% after 560 h of operation.