PM567-Doped solid dye lasers based on PMMA

Polymers are a kind of attractive hosts for laser dyes due to their high transparency in both pumping and lasing ranges and superior optical homogeneity. In this paper solid dye samples based on polymethyl methacrylate （PMMA） doped with different concentrations of 1, 3, 5, 7, 8 -pentamethyl-2, 6-diethylpyrromethene-BF2 （PM567） are prepared. The absorption, fluorescence and lasing spectra of the samples are obtained. Wide absorption and fluorescence bands are obtained and a red shift of the maxima of the lasing emission spectra is observed. With the second-harmonic generation of Q-switched Nd：YAC laser （532 nm, -20 ns） pumping the samples longitudinally, the slope efficiencies of the samples are obtained. There is an optimal dye concentration for the highest slope efficiency when the pumping energy is lower than some typical value （-250 mJ）, and the highest slope efficiency 35.6% is obtained in the sample with a dye concentration of 2 × 10^-4 mol/L. Pumping the samples at a rate of 10Hz with a pulse energy as high as 200 mJ （the fluence is 0.2 J/cm^2）, the output energy drops to one-half of its initial value after approximate 15500 pulses and the normalized photostability is 5.17CJ/mol. A kind of solid dye laser which could have some applications is built.

Energy transfer in solid-state dye lasers based on methyl methacrylate co-doped with sulforhodamine B and crystal violet

Laser action in methyl methacrylate （MMA） co-doped with sulforhodamine B and crystal violet dyes was investi- gated. The dye mixture was incorporated into a solid polymeric matrix and was pumped by a 532-nm Nd：YAG laser. Distributed feedback dye laser （DFDL） action was induced in the dye mixture using a prism arrangement both in the donor and acceptor regions by an energy transfer mechanism. Theoretically, the characteristics of acceptor and donor DFDLs, and the dependence of their pulse widths and output powers on acceptor-donor concentrations and pump power, were studied. Experimentally, the output energy of DFDL was measured at the emission peaks of donor and acceptor dyes for different pump powers and different acceptor-donor concentrations. Tuning of the output wavelength was achieved by varying the period of the gain modulation of the laser medium. The laser wavelength showed continuous tunability from 563 nm to 648 nm.

Different Approaches of Employing Cholesteric Liquid Crystals in Dye Lasers

Two ways of employing cholesteric liquid crystals in tunable dye lasers are considered: the cholesterics as distributed feedback medium and the cholesterics as resonator mirrors. In the dye doped distributed feedback cholesteric liquid crystal lasers the frequency tuning is achieved exploiting light induced effects or using a specially designed cell assembling a chiral dopant concentration gradient in combination with suitable distribution of different dyes. Another approach represents the lasing in a multilayer system consisting of a dye doped isotropic solvent sandwiched between two CLC layers.

Monitoring Xylem Transport in the Stem of Lilium lancifolium Using Fluorescent Dye 5(6)-Carboxyfluorescein Diacetate

The xylem undergoes physiological changes in response to various environmental conditions during the process of plant growth.To understand these physiological changes,it is extremely important to observe the transport of xylem.In this study,the distribution and structure of vascular bundle in Lilium lancifolium were observed using the method of semithin section.Methods for introducing a fluorescent tracer into the xylem of the stems were evaluated.Then,the transport rule of 5(6)-Carboxyfluorescein diacetate(CFDA)in the xylem of the stem of L.lancifolium was studied by fluorescence dye in live cells tracer technology.The results showed that the vascular bundles of L.lancifolium were scattered in the basic tissue,the peripheral vascular bundles were smaller and densely distributed,and the closer to the center,the larger the volume of vascular bundles and the more sparsely distributed.The vascular bundles of L.lancifolium are limited external tenacity vascular bundles,which are composed of phloem and xylem.The most suitable method for CFDA labeling the xylem of isolated stem segments of L.lancifolium was solution soaking for 24 h.The running speed of CF in the isolated stem was 0.3 cm/h,which was consistent with the running speed of the material in the field.CF could be transported between the xylem and parenchyma cells,indicating that the material transport in the xylem could be through the symplastic pathway.The above results laid a foundation for the study of the xylem transport mechanism and the xylem pathogen disease of lily.

Textile dyeing wastewater negatively influences the hematological profile and reproductive health of male Swiss albino mice

Objective:To determine the effects of textile dyeing industrial wastewater on the hematological parameters and reproductive health including histoarchitecture of male gonad(testes)of mice.Methods:Twenty-four Swiss albino mice at 4-weeks old were divided into four groups(n=6 per group).Mice of group 1 supplied with normal drinking water were served as the control group.Mice of group 2,3 and 4 were supplied normal drinking water mixed with textile dyeing wastewater at 5%,10% and 20% concentration,respectively.After completing 24 weeks of treatment,different hematological profile,weight of testes,gonadosomatic index(GSI),sperm concentration and morphology were measured.Moreover,histopathological changes in testes were examined.Results:Hematocrit value and hemoglobin concentrations were decreased in all groups of wastewater-treated mice compared to the control group.Likewise,weight of testes,GSI and sperm concentration were decreased significantly in wastewater-treated mice in comparison to the control group.The percentage of morphologically healthy epididymal sperm was significantly reduced in wastewater-treated mice.Histopathological examination revealed degenerative changes in seminiferous tubules,a smaller number of spermatogenic cells,elongation of seminiferous tubules and degenerative changes of seminiferous tubules in wastewater-treated mice.Conclusions:Textile dyeing wastewater has harmful effects on hematological profile and reproductive health of male mice.

Bioremediation of Textile Azo Dyes Amido Black 10B, Reactive Black 5, Reactive Blue 160 by Lentinus squarrosulus AF5 and Assessment of Toxicity of the Degraded Metabolites

Bioremediation is an eco-compatible and economical approach to counter textile dye menace. The isolated Lentinus squarrosulus AF5 was assessed for decolourization of textile azo dyes, and had shown ~93%, 88% and 70% decolorization of Reactive blue 160 (RB160), Reactive black 5 (RB5) and Amido black 10B (AB10B) respectively. Further analysis using UV-vis, HPLC, and FTIR, 1H NMR had shown the degradation of the dyes. Toxicity analysis of the metabolites was performed using seed germination and plant growth on two agriculturally important plants Guar (Cyamopsis tetragonoloba) and wheat (Triticum aestivum) as well as cytotoxicity analysis using the human keratinocyte cell line (HaCaT). The dye mix appeared inhibitory for seed germination (20% - 40%), whereas metabolites were non-inhibitory for germination. Treatment of HaCaT cells with of dye mix and metabolites led into 45% and ~100% of cell viability of HaCaT cells respectively. Therefore, metabolites following degradation of the dye mix were observed to be non-toxic.

Progress and prospects of Mg-based amorphous alloys in azo dye wastewater treatment

Mg-based amorphous alloys exhibit efficient catalytic performance and excellent biocompatibility with a promising application probability,specifically in the field of azo dye wastewater degradation.However,the problems like difficulty in preparation and poor cycling stability need to be solved.At present,Mg-based amorphous alloys applied in wastewater degradation are available in powder and ribbon.The amorphous alloy powder fabricated by ball milling has a high specific surface area,and its reactivity is thousands of times better than that of gas atomized alloy powder.But the development is limited due to the high energy consumption,difficult and costly process of powder recycling.The single roller melt-spinning method is a new manufacturing process of amorphous alloy ribbon.Compared to amorphous powder,the specific surface area of amorphous ribbon is relatively lower,therefore,it is necessary to carry out surface modification to enhance it.Dealloying is a way that can form a pore structure on the surface of the amorphous alloys,increasing the specific surface area and providing more reactive sites,which all contribute to the catalytic performance.Exploring the optimal conditions for Mg-based amorphous alloys in wastewater degradation by adjusting amorphous alloy composition,choosing suitable method to preparation and surface modification,reducing cost,expanding the pH range will advance the steps to put Mg-based amorphous alloys in industrial environments into practice.

Gigahertz frequency hopping in an optical phase-locked loop for Raman lasers

Raman lasers are essential in atomic physics,and the development of portable devices has posed requirements for time-division multiplexing of Raman lasers.We demonstrate an innovative gigahertz frequency hopping approach of a slave Raman laser within an optical phase-locked loop(OPLL),which finds practical application in an atomic gravimeter,where the OPLL frequently switches between near-resonance lasers and significantly detuned Raman lasers.The method merges the advantages of rapid and extensive frequency hopping with the OPLL’s inherent low phase noise,and exhibits a versatile range of applications in compact laser systems,promising advancements in portable instruments.

Phase-locked single-mode terahertz quantum cascade lasers array

We demonstrated a scheme of phase-locked terahertz quantum cascade lasers(THz QCLs)array,with a single-mode pulse power of 108 mW at 13 K.The device utilizes a Talbot cavity to achieve phase locking among five ridge lasers with first-order buried distributed feedback(DFB)grating,resulting in nearly five times amplification of the single-mode power.Due to the optimum length of Talbot cavity depends on wavelength,the combination of Talbot cavity with the DFB grating leads to better power amplification than the combination with multimode Fabry-Perot(F-P)cavities.The Talbot cavity facet reflects light back to the ridge array direction and achieves self-imaging in the array,enabling phase-locked operation of ridges.We set the spacing between adjacent elements to be 220μm,much larger than the free-space wavelength,ensuring the operation of the fundamental supermode throughout the laser's dynamic range and obtaining a high-brightness far-field distribution.This scheme provides a new approach for enhancing the single-mode power of THz QCLs.

Matching Dyeing and Properties of Silk Fabrics with Natural Edible Pigments

The silk fabrics were matching dyed with three natural edible pigments(red rice red,ginger yellow and gardenia blue).By investigating the dyeing rates and lifting properties of these pigments,it was observed that their compatibilities were excellent in the dyeing process:dye dosage 2.5%(omf),mordant alum dosage 2.0%(omf),dyeing temperature 80℃and dyeing time 40 min.The silk fabrics dyed with secondary colors exhibited vibrant and vivid color owing to the remarkable lightness and chroma of ginger yellow.However,gardenia blue exhibited multiple absorption peaks in the visible light range,resulting in significantly lower lightness and chroma for the silk fabrics dyed with tertiary colors,thus making it suitable only for matte-colored fabrics with low chroma levels.In addition,the silk fabrics dyed with these three pigments had a color fastness that exceeded grade 3 in resistance to perspiration,soap washing and light exposure,indicating acceptable wearing properties.The dyeing process described in this research exhibited a wide range of potential applications in matching dyeing of protein-based textiles with natural colorants.

Characteristic analysis of 1.06μm long-cavity diode lasers based on asymmetric waveguide structures

In long-cavity edge-emitting diode lasers,longitudinal spatial hole burning(LSHB),two-photon ab⁃sorption(TPA)and free carrier absorption(FCA)are among the key factors that affect the linear increase in out⁃put power at high injection currents.In this paper,a simplified numerical analysis model is proposed for 1.06μm long-cavity diode lasers by combining TPA and FCA losses with one-dimensional(1D)rate equations.The ef⁃fects of LSHB,TPA and FCA on the output characteristics are systematically analyzed,and it is proposed that ad⁃justing the front facet reflectivity and the position of the quantum well(QW)in the waveguide layer can improve the front facet output power.

Biocatalytic enhancement of laccase immobilized on ZnFe_(2)O_(4) nanoparticles and its application for degradation of textile dyes

Efficient and convenient treatment of industrial dyeing wastewater is of great significance to guarantee human and animal health.This work presented the enhanced catalytic activity at pH 3.0 of laccase immobilized on amino-functionalized ZnFe_(2)O_(4) nanoparticles(ZnFe_(2)O_(4)-laccase)and its application for the degradation of textile dyes.Due to the existence of a large number of oxygen vacancies on the surface of the ZnFe_(2)O_(4) nanoparticles,negative ions accumulated on the magnetic carriers,which resulted in a harsh optimal pH value of the ZnFe_(2)O_(4)-laccase.Laccase activity assays revealed that the ZnFe_(2)O_(4)-laccase possessed superior pH and thermal stabilities,excellent reusability,and noticeable organic solvent tolerance.Meanwhile,the ZnFe_(2)O_(4) laccase presented efficient and sustainable degradation of high concentrations of textile dyes.The initial decoloration efficiencies of malachite green(MG),brilliant green(BG),azophloxine,crystal violet(CV),reactive blue 19(RB19),and procion red MX-5B were approximately 99.1%,95.0%,93.3%,87.4%,86.1%,and 85.3%,respectively.After 10 consecutive reuses,the degradation rates of the textile dyes still maintained about 98.2%,92.5%,83.2%,81.5%,79.8%and 65.9%,respectively.The excellent dye degradation properties indicate that the ZnFe_(2)O_(4)-laccase has a technical application in high concentrations of dyestuff treatment.

Optical facet coatings for high-performance LWIR quantum cascade lasers atλ∼8.5μm

We report on the performance improvement of long-wave infrared quantum cascade lasers(LWIR QCLs)by studying and optimizing the anti-reflection(AR)optical facet coating.Compared to the Al2O3 AR coat⁃ing,the Y_(2)O_(3)AR coating exhibits higher catastrophic optical mirror damage(COMD)level,and the optical facet coatings of both material systems have no beam steering effect.A 3-mm-long,9.5-μm-wide buried-heterostruc⁃ture(BH)LWIR QCL ofλ~8.5μm with Y_(2)O_(3)metallic high-reflection(HR)and AR of~0.2%reflectivity coating demonstrates a maximum pulsed peak power of 2.19 W at 298 K,which is 149%higher than that of the uncoated device.For continuous-wave(CW)operation,by optimizing the reflectivity of the Y_(2)O_(3)AR coating,the maximum output power reaches 0.73 W,which is 91%higher than that of the uncoated device.

Electrochemical Degradation of Indigocarmine Dye at Ni/Graphite Modified Electrode in Aqueous Solution

Nickel Graphite modified electrode (Ni/GME) was prepared by electrochemical method and degradation of Indigocarmine (IC) dye was carried out. An investigation between the efficiency of degradation by graphite electrode and the Ni/graphite modified electrode has been carried out. The different effects of concentration, current density and temperature on the rate of degradation were studied. This study shows that the rate of the degradation is more for Ni doped modified graphite electrode. UV-Visible spectra before and after degradation of the dye solution were observed. The thin film formation of Ni or encapsulated in graphite rod is observed by scanning electron microscopy and energy dispersive X-ray spectroscopy (SEM & EDAX). The instantaneous current effectiveness values of different experimental conditions are evaluated. The anodic oxidation by Ni/ graphite modified electrode showed the complete degradation of aqueous solution indigocarmine, which is confirmed by UV-Visible and chemical oxygen demand (COD) measurements. The dye is converted into CO2, H2O and simpler inorganic salts. The results observed for reuse of modified electrodes indicate that the Ni/graphite modified electrode would be a promising anode for electrochemical degradation of indigocarmine. This method can be applied for the remediation of waste water containing organics, cost-effective and simple.

Procion MX Dyes在彩色蜡染制作工艺中的应用研究

文章以彩色蜡染制作工艺为研究对象,将文献研究法与实践相结合,从画蜡技巧、上色与固色原理、艺术表现技巧等方面解读Procion MX Dyes在彩色蜡染制作工艺中的应用原则和技巧。借助Procion MX Dyes的应用,提升了彩色蜡染的艺术表现力和使用价值,为蜡染产业的发展提供了可行性参考。

Progress in the research on organic piezoelectric catalysts for dye decomposition

Organic contaminants have posed a direct and substantial risk to human wellness and the environment.In recent years,piezo-electric catalysis has evolved as a novel and effective method for decomposing these contaminants.Although piezoelectric materials offer a wide range of options,most related studies thus far have focused on inorganic materials and have paid little attention to organic materi-als.Organic materials have advantages,such as being lightweight,inexpensive,and easy to process,over inorganic materials.Therefore,this paper provides a comprehensive review of the progress made in the research on piezoelectric catalysis using organic materials,high-lighting their catalytic efficiency in addressing various pollutants.In addition,the applications of organic materials in piezoelectric cata-lysis for water decomposition to produce hydrogen,disinfect bacteria,treat tumors,and reduce carbon dioxide are presented.Finally,fu-ture developmental trends regarding the piezoelectric catalytic potential of organic materials are explored.

Optimizing laser coupling,matter heating,and particle acceleration from solids using multiplexed ultraintense lasers

Realizing the full potential of ultrahigh-intensity lasers for particle and radiation generation will require multi-beam arrangements due to technology limitations.Here,we investigate how to optimize their coupling with solid targets.Experimentally,we show that overlapping two intense lasers in a mirror-like configuration onto a solid with a large preplasma can greatly improve the generation of hot electrons at the target front and ion acceleration at the target backside.The underlying mechanisms are analyzed through multidimensional particle-in-cell simulations,revealing that the self-induced magnetic fields driven by the two laser beams at the target front are susceptible to reconnection,which is one possible mechanism to boost electron energization.In addition,the resistive magnetic field generated during the transport of the hot electrons in the target bulk tends to improve their collimation.Our simulations also indicate that such effects can be further enhanced by overlapping more than two laser beams.

975 nm multimode semiconductor lasers with high-order Bragg diffraction gratings

The 975 nm multimode diode lasers with high-order surface Bragg diffraction gratings have been simulated and calcu-lated using the 2D finite difference time domain(FDTD)algorithm and the scattering matrix method(SMM).The periods and etch depth of the grating parameters have been optimized.A board area laser diode(BA-LD)with high-order diffraction grat-ings has been designed and fabricated.At output powers up to 10.5 W,the measured spectral width of full width at half maxi-mum(FWHM)is less than 0.5 nm.The results demonstrate that the designed high-order surface gratings can effectively nar-row the spectral width of multimode semiconductor lasers at high output power.

Collective coherent emission of electrons in strong laser fields and perspective for hard x-ray lasers

Coherent motion of particles in a plasma can imprint itself on radiation.The recent advent of high-power lasers—allowing the nonlinear inverse Compton-scattering regime to be reached—has opened the possibility of looking at collective effects in laser–plasma interactions.Under certain conditions,the collective interaction of many electrons with a laser pulse can generate coherent radiation in the hard x-ray regime.This perspective paper explains the limitations under which such a regime might be attained.

On the generation of high-quality Nyquist pulses in mode-locked fiber lasers

Nyquist pulses have wide applications in many areas,from electronics to optics.Mode-locked lasers are ideal platforms to generate such pulses.However,how to generate high-quality Nyquist pulses in mode-locked lasers remains elusive.We address this problem by managing different physical effects in mode-locked fiber lasers through extensive numerical simulations.We find that net dispersion,linear loss,gain and filter shaping can affect the quality of Nyquist pulses significantly.We also demonstrate that Nyquist pulses experience similariton shaping due to the nonlinear attractor effect in the gain medium.Our work may contribute to the design of Nyquist pulse sources and enrich the understanding of pulse shaping dynamics in mode-locked lasers.