Graphene oxide/hydrotalcite modified polyethersulfone nanohybrid membrane for the treatment of lead ion from battery industrial effluent

In the present study, polyethersulfone based nanohybrid membranes were effectively fabricated by incorporating graphene oxide(GO) and hydrotalcite(HT) nanosheets into the membrane structure. HT was prepared to overcome the irreversible agglomeration behavior of GO at a high concentration which affects the performance of the membranes. In particular, the shedding of HT in formamide provides a two-dimensional nanosheet with a higher positive charge density to prevent the restacking of GO nanosheets. Here, exfoliated GO and HT with different combinations(1:1, 1:2 and 1:3) were infused in the membrane matrix to treat lead-acid battery effluent effectively. Finally, the hybrid membranes were characterized for hydrophilicity, mechanical strength and pure water flux. In combination with the superior properties of GO and HT, the prepared hybrid membranes can be used as effectively to improve the separation and permeation performance. The phase inversion process eliminated the leaching of nanoparticles from the membrane matrix. The reusability of the hybrid membrane was achieved using0.1 mol·L^(-1)NaOH solution and reused without significant reduction in lead removal efficiency. The cost analysis of the membrane was also estimated from the lab study. Therefore, the present study suggested the selective and sustainable treatment of lead from a real-life effluent.

Selective recovery of lead from zinc oxide dust with alkaline Na_2EDTA solution

The selective recovery of lead from the zinc oxide dust using an alkaline Na2EDTA solution was investigated. The effects of temperature, leaching time, Na2EDTA concentration and initial NaOH concentration on the leaching rates of lead and zinc were studied. The following optimized leaching conditions were obtained： liquid-to-solid ratio 5：1 mL/g, stirring speed 650 r/min, Na2EDTA concentration 0.12 mol/L, initial NaOH concentration 0.5 mol/L, leaching temperature 70 ℃, leaching time 120 min. Under the optimized conditions, the average leaching rates of lead, zinc, fluoride and chloride are 89.92%, 0.94%, 62.84% and 90.02%, respectively. The filtrate was used to electrowin lead powders. The average current efficiency of electrowinning is about 93% and lead content is higher than 98% under the conditions of temperature of 60 ℃, current density of 200 A/m2, H3PO4 concentration of 1.5 g/L, and lead ion concentration of above 5 g/L. The consumption of Na2EDTA and the direct current are about respectively 0.218 kg and 0.958 kW·h for per kilogram of lead powder.

Thermodynamic model of lead oxide activity in PbO-CaO-SiO_2-FeO-Fe_2O_3 slag system

According to the ion and molecule coexistence theory, a thermodynamic model of lead oxide activity in PbO-CaO-SiO2-FeO-Fe2O3 slag system was established at the temperature of 1273-1733 K. The activities of Pb O in slag were calculated, and their equal activity curves were plotted. The influences of slag basicity Q, iron oxide rate R and temperature T on activity NPb O and activity coefficient γPbO were also investigated. Results show that the calculated values of γPb O are in good agreement with the reported experimental data, showing that the model can wholly embody the slag structural characteristics. NPbO departures positively from Raoult values, and increases with increasing Pb O content in slag but changes little with T. γPbO increases with increasing Q, and goes through the maximum with increasing R for basic slag（Q0.3）. Results can be applied to the thermodynamic research and operational optimization of modern lead smelting technologies.

Comparative study of oxidation ability between boron-doped diamond (BDD) and lead oxide (PbO_2) electrodes

The electrochemical oxidation capabilities of two high-performance electrodes,the boron-doped diamond film on Ti （Ti/BDD） and the lead oxide film on Ti （Ti/PbO2）,were discussed.Hydroxyl radicals （·HO） generated on the electrode surface were detected by using p-nitrosodimethylaniline （RNO） as the trapping reagent.Electrochemical oxidation measurements,including the chemical oxygen demand （COD） removal and the current efficiency （CE）,were carried out via the degradation of p-nitrophenol （PNP） under the galvanostatic condition.The results indicate that an indirect reaction,which is attributed to free hydroxyl radicals with high activation,conducts on the Ti/BDD electrode,while the absorbed hydroxyl radicals generated at the Ti/PbO2 surface results in low degradation efficiency.Due to quick mineralization which combusts PNP to CO2 and H2O absolutely by the active hydroxyl radical directly,the CE obtained on the Ti/BDD electrode is much higher than that on the Ti/PbO2 electrode,notwithstanding the number of hydroxyl radicals produced on PbO2 is higher than that on the BDD surface.

Investigation on the deactivation cause of lead-zinc double oxide for the synthesis of diphenyl carbonate by transesterification

The deactivation cause of lead-zinc double oxide for synthesis of diphenyl carbonate （DPC） by transesterification of dimethyl carbonate （DMC） with phenol has been investigated. X-ray diffraction （XRD）, X-ray photoelectron spectroscopy （XPS）, infrared spectroscopy （IR）, thermogravimetry analysis （TG）, atomic absorption spectroscopy and elementary analysis are employed for the catalyst characterization. The results show that, the formation of Pb4O（OC6H5）6 through the reaction of phenol and lead species in the catalyst leads to the crystal phase change of active component and serious leaching of lead, which is the cause of the catalyst deactivation. In addition, the composition of the leached lead is ascertained to be a mixture of Pb4O（OC6H5）6 and PbO with the weight percentage of 62.7% and 37.3%, respectively.

A low-cost green approach for synthesis of lead oxide from waste lead ash for use in new lead-acid batteries

This paper proposes a novel method relating to the recycling of waste lead ash originated from procedure of lead alloy production.The spent lead ash was first disposed by acetic acid leaching system,where lead ash structure wrapping impurities would be destroyed.The synthesis of lead oxide products was conducted at a lower temperature of 90℃.The effect of molar ratio of CH3 COOH to lead content of the ash on leaching efficiency was studied through the acetic acid leaching system.The results demonstrate that 84.6%of lead could be obtained in the leaching solution,while merely 0.7%of Fe blend in solution within a leaching time of 120 min.In the stage of lead oxide synthesis from leaching solution,the yield of lead oxide products could reach up to 94.4%when the molar ratio of NaOH to lead in filtrate was 2.5.This novel green method could shed light on the reuse of lead from exhausted ash with a much more convenient and environmentally friendly procedure.

Characteristics of Lead Sorption on Clay Minerals in Relation to Metal Oxides

Difference of montmorillonite (Mt), illite (It) and kaolinite (Kt) in lead sorption characteristics and the effects of amorphous Fe and Al oxide coatings on the characteristics were experimentally studied with logistic model. The sorption curves had sigmoid feature due to use of acetate-type buffer solution. With the model the sorption process could be divided into four stages and the sorption characteristics at the stages were discussed. The results showed that, after Mt, It and Kt were coated by amorphous Fe oxide, their maximum sorption capacity (MSC) and percentage of high-SSC concentration scope (HCS) of Pb2+ increased markedly, but the specific sorption capacity (SSC) decreased. With regard to effects of amorphous Al oxide coating, except for It+AI, the SSC of other samples showed a downtrend, despite that their MSC remained unchanged. Eventually, the gray correlation degrees to Pb2+ sorption for different physicochemical characteristics of the clay minerals were indicated to be higher for hydronium, zero point of surface charge and hydroxy, but lower for specific surface area, density of surface charge and amount of surface charges.

Potential Association of Lead Exposure During Early Development of Mice With Alteration of Hippocampus Nitric Oxide Levels and Learning Memory

Objective Chronic lead （Pb） exposure during development is known to produce learning deficits. Nitric oxide participates in the synaptic mechanisms involved in certain forms of learning and memory. This study was designed to clarify whether Pb-induced impairment in learning and memory was associated with the changes of nitric oxide levels in mice brains. Methods Sixty Balb/c mice aged l0 days were chosen. A model of lead exposure was established by drinking 0.025%, 0.05% 0.075% lead acetate, respectively for 8 weeks. The controls were orally given distilled water. The ability to learn and memorize was examined by open field test, T-water maze test. In parallel with the behavioral data, NO level of hippocampus tissue was detected by biochemical assay. Results Compared with control groups, （1） the weight of 0.075% group was significantly reduced （P〈0.05）; （2） The number of times in mice attaining the required standards in T-water maze test was lower in 0.075% group （P〈0.01）. No significant difference was found between experimental and control groups in open field test （P〉0.05）; （3） NO level of mouse hippocampus tissue was decreased in 0.075% group （P〈0.01）. Conclusions The findings suggest that decreased hippocampus NO level may contribute to the Pb-induced deficits in learning and memory processes.

Lead and Cadmium Adsorption onto Iron Oxides and Manganese Oxides in the Natural Surface Coatings Collected on Natural Substances in the Songhua River of China

Natural surface coatings collected from natural substances （NSCsNS） were employed to study the roles of the main chemical components （iron oxides, manganese oxides, and other components） in controlling the adsorption of lead（Pb） and cadmium（Cd） in aquatic environments. The selective chemical extraction followed by the adsorption of Pb and Cd experiments and statistical analysis, were used to investigate the adsorption property of each component. Hydroxylamine hydrochloride was used to remove manganese oxides selectively, and sodium dithionite was used to extract iron oxides and manganese oxides. The result indicated that iron oxides and manganese oxides played an important role in the adsorption of Pb and Cd on NSCsNS, and the relative contribution was about two-thirds. The contribution of manganese oxides was the greatest, with a lesser role indicated for other components. The adsorption ability of manganese oxides for Pb and Cd was greater than that of iron oxides or other components for Pb and Cd. The Pb adsorption observed in each component was greater than Cd adsorption.

Sulphidization flotation for recovery of lead and zinc from oxide-sulfide ores

A new flowsheet was developed to recover the valuable minerals from oxide or oxide-sulfide ores of lead and zinc. The flowsheet consisted of flotation of sulfide minerals, desliming and sulphidization-flotation of oxide minerals. The corresponding reagent system and techniques to the flowsheet were investigated. Batch and continuous tests show that the dosage of sodium sulfide, temperature, and collector type are main affecting factors on the recovery of smithsonite and cerussite. For the flotation of cerussite, there is an appropriate dosage of sodium sulfide at which the recovery reaches its maximum value. The required sodium sulfide for smithsonite flotation is higher than that for cerussite and the recovery of smithsonite flotation increases with the dosage of sodium sulfide at low level and becomes insensitive at high dosage. The appropriate temperature for smithsonite and cerussite flotation is found to be 2540℃. Amines are found to be the effective collectors for the flotation of smithsonite after sulphidization. Investigation also shows that desliming prior to sulphidization-flotation is essential to the effective recovery of smithsonite and cerussite, and the desliming process of two-stage hydrocyclon is well feasible and effective for the treatment of lead-zinc oxide ores. A further treatment on the cerussite flotation concentrate by shaking table is proposed to obtain higher lead grade.

Comparative Study between Lead Oxide and Lead Nitrate Polymer as Gamma-Radiation Shielding Materials

In this work, the Styrene-butadiene rubber (SBR)/lead oxide and the Styrene-butadiene rubber (SBR)/lead nitrate composites were prepared as gamma-radiation shielding materials. The investigated materials were prepared with three different weight percentage of lead oxide and lead nitrate (30, 50 and 70 wt%). The mass attenuation coefficients (μm) for all composite samples were measured experimentally at 511 and 661.6 keV photon energies. The measurements were made by performing transmission experiments with a 3'' × 3'' NaI (Tl) scintillation detector, which had an energy resolution of 7% at 0.662 MeV for the gamma-rays from the decay of 137Cs. The effective atomic numbers (Zeff) and the effective electron densities (Neff) were determined experimentally. Also they were determined theoretically using the obtained μm values for the studied composites samples by WinXCom program. The obtained results show that the experimental values of the composites are found to be in a good agreement with the theoretical values. It is recognized that the mass attenuation coefficient (μm), effective atomic numbers (Zeff) and the effective electron densities (Neff) are increased in the composite samples which contain lead oxides than which contain lead nitrates. Finally, the Styrene-butadiene rubber (SBR)/lead oxide is better than Styrene-butadiene rubber (SBR)/lead nitrate polymer as gamma radiation shielding.

Preparation of elemental As from As-Sb fly ash using continuous reductive method with additive of lead oxide

To recycle arsenic from an As-Sb fly ash,a newly continuous reductive method for obtaining elemental As with additive of PbO was proposed.In the first reduction stage,PbO promoted the As segregation from the As-Sb fly ash,due to which most As volatilized and Sb retained in roasted residues in phases of As-Sb-Pb-O and As-Sb-Pb alloy.With the increase of PbO and reductant amounts,the Sb fixation rate increased in the first reduction stage,and further the Sb content in the elemental As obtained from the second reduction stage decreased.After being roasted for 30 min at 550℃ with the addition of 20%activated carbon and 12%PbO in the first reduction stage,the As volatilization rate and Sb fixation rate from the As-Sb fly ash reached 92.86%and 79.38%,respectively.Then through the second reduction of the volatile matters at 650℃,the As and Sb contents in the obtained elemental As reached 99.07 wt%and 0.22 wt%respectively,indicating that the obtained As could be used to prepare high purity As,thereby rendering the As-Sb fly ash recycling.

Epicatechin attenuates lead(Pb)-induced cognitive impairment in mice:regulation on Nrf2 signaling pathway,and interference on the interaction between Pb with albumin

Epicatechin(EC)was used in this study to antagonize the cognitive dysfunction caused by lead(Pb)exposure in mice.Eight-week-old male Kunming mice were treated with PbCl_(2)(20 mg/kg)and/or EC(50 mg/kg)by gavage administration for 4 weeks.Morris water maze test showed that EC could improve memory dysfunction induced by Pb.EC antagonized Ca^(2+)overload,activated Nrf2 signaling pathway and reduced the accumulation of Pb in the brain and serum,which suggested that EC might alter Pb distribution in mice.In vitro,spectroscopic analysis,potentiometric titration and docking studies were applied to inquiry into the interaction between bovine serum albumin(BSA)and Pb^(2+)in presence or absence of EC.EC was proved to chelate Pb^(2+)and reduced the interaction between BSA and Pb^(2+).In summary,EC might protect Pb-induced cognitive impairment by activating Nrf2 signaling pathway,and suppressing Pb accumulation via interference on the binding of Pb to albumin.

Synthesis of Micron-sized Hexagonal and Flowerlike Nanostructures of Lead Oxide (PbO_2) by Anodic Oxidation of Lead

Micron sized hexagon- and flower-like nanostructures of lead oxide（α-PbO2） have been synthesized by very simple and cost effective route of anodic oxidation of lead sheet. These structures were easily obtained by the simple variation of applied voltage from 2-6 V between the electrodes. Lead sheet was used as an anode and platinum sheet served as a cathode. Anodic oxidation at 2 V resulted in the variable edge sized（1-2 μm） hexagon-like structures in the electrolyte. When the applied potential was increased to 4 V a structure of distorted hexagons consisting of some flower-like structures were obtained. Further increment of potential up to 6 V resulted in flower like structures of α-PbO2 having six petals. The diameter of the flower-like structures was 200-500 nm and the size of a petal was 100-200 nm.

Study on experiment and mechanism of thermal dissolved sulfuration of low grade lead-zinc oxide ore in lanpin

The thermal dissolved sulfuration technology is brought forward and performed based on the characteristic of low grade lead-zinc oxide ore in lanpin. Using sulfur as the sulphidizing agent in the experiment, the oxides in the sandstone and ignimbrite are changed into sulfides. The disproportionation reaction of sulfur in a solution is confirmed as 4S＋3H2O=2S^2-＋S2O3^2--＋6H^＋. The dynamics process is studied and the first-order reaction rate equation -1n（1-a）=ktt is obtained. The effects of the reactive products, stirring speed, dosage of sulfuration agent, value of pH and sulphidizing temperature on the sulfuration of oxide ore are investigated. The results indicate that the reactive apparent activation energy is 100.8 kJ/mol and the sulfuration ratio of lead-zinc oxide ore reaches 60% under the conditions of pH 5.9-7.5, the sulfuration temperature of 130 ℃, sulfuration time of 180 min and the stirring speed of 800 r/min.

The Processing Mineralogy for Lead and Zinc Oxide Ore in Sichuan

Using variety of modern testing methods, the processing mineralogical characteristics for a lead and zinc oxide ore in Sichuan were studied systematically. The chemical analysis result shows that the lead and zinc oxide content exceeding the minimum industrial grade and iron ore, total iron content reaches a minimum industrial grade and associated with gold and silver; The mineralogical analysis result shows that lead and zinc mineral composition and configuration are very complexity. The zinc minerals and zinciferous minerals are sphalerite, hemimorphite, Smithsonite, Hydrozincite, zinc chlorite, limonite, zinc dolomite and zincocalcite; lead minerals and plumbiferous minerals are mainly galena, cerussite, anglesite, limonite and Coronadite; The minerals disseminated grain size are very fine and mineral dissemination characteristics are very complex ; expected theoretical recoveries for lead and zinc were 72% and 67% respectively. The results of this study provide basic data and theoretical basis for ore dressing.

A Comparative Investigation of Lead Sulfate and Lead Oxide Sulfate Study of Morphology and Thermal Decomposition

The compound lead oxide sulfate PbSO4.PbO was prepared in our laboratory. The Thermal behavior of PbSO4 was studied using techniques of Thermogravimetry under air atmosphere from 25 to 1200°C. The identity of both compounds was confirmed by XRD technique. Results obtained using both techniques support same decomposition stages for this compound. The electron microscopic investigations are made by SEM and TEM. The compound is characterized by XRD and the purity was determined by analytical Methods. Also a series of thermogravimetric analysis is made and the ideal condition is determined to convert this compound to pure lead oxide.

X-Ray Absorption Spectroscopy Analysis of Lead Species Adsorbed on Various Oxides from High pH Solution

Lead dissolved in water must be removed in order not to cause diseases, especially from high pH aqueous solution. Various oxides having high specific surface area are often applied to remove lead in water media. To improve removal ability for lead species, it is necessary to understand the adsorbed structure of lead species on oxides. At first, the adsorption behavior of lead from high pH solution in the presence of Ca2+ and Na+ was compared. Lead and calcium species were adsorbed up to the monolayer, and the adsorption isotherm was analyzed as Langmuir-type adsorption. In the presence of Ca2+, the amount of removed lead was reduced. To clarify this influence of Ca2+, X-ray absorption spectroscopy was adopted. It was for the first time revealed that lead species at pH > 12 and pH < 10.5 differed, and that lead species adsorbed on various oxides had a similar structure.

Fe-Oxide Nanomaterial: Synthesis, Characterization and Lead Removal

Organic solvent free iron oxide nanomaterial used for lead removal was synthesized by co-precipitation method. Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopic with energy dispersive X-ray analysis (SEM-EDX), X-ray diffraction (XRD) and thermo gravimetric-differential thermal (TG-DTA) analysis were used to determine the surface characteristics and analysis of iron oxide. Optimization of solution pH, adsorbent dosage, contact time, agitation speed and initial lead ion concentration were conducted for further adsorption isotherm, kinetics, thermodynamics and desorption study. Langmuir sorption isotherm model fits the adsorption data better than Freundlich, Dubinin-Radushkevich (D-RK) and Flory-Huggins (FH) models. The mean adsorption energy and free energy obtained from D-RK and FH models guides that the mechanism was under control of physical adsorption and actuality of spontaneous reaction, respectively. From kinetics of adsorption pseudo second (PSO) model fits well than pseudo first (PFO) and Elovich adsorption-reaction models. And to test whether the reaction is under control of adsorption-diffusion or not the intra particle diffusion (IPD) model was tested, but it fails to pass through the origin. This indicates that the reaction mechanism only under control of adsorption-reaction. The maximum adsorption capacity (qmax) of the adsorbent was 70.422 mg/g.

New Constraints on the Environmental Impact of Iron Oxides and Lead-Zinc Mines in Red Sea Hills,Egypt

Iron oxides and lead-zinc deposits in host rocks located in ten drainage basins in the coastal plain of the Red Sea,Egypt,have been subjected to important mining activities.The drainage basins were analyzed to estimate the transportations of these minerals. Fourteen soil samples and fifteen plant samples were collected from sites located in the basin and also in neighboring area and chemically analyzed.In