Early clinical outcome with lens position adjustment following implantable collamer lens surgery

AIM:To observe early clinical outcome with lens position adjustment following the implantable collamer lens(ICL)surgery.METHODS:Sixty patients were selected for this retrospective study.One eye from each patient received Toric ICL for astigmatism correction,and the other received non-astigmatic ICL surgery using horizontal position.Patients with higher postoperative arch height were selected,and their non-astigmatic eye clinical outcome were observed after ICL surgery at 1wk,1,and 3mo.The clinical measurements included uncorrected visual acuity(UCVA),intraocular pressure(IOP),refractive state,corneal endothelium cell count,and arch height.Three months later,the ICL in each patient’s non-astigmatic eye was adjusted to the vertical from the horizontal position.The results were compared before and 1wk,1,and 3mo after adjustment.RESULTS:UCVA and IOP were significantly reduced 1wk after position adjustment compared to 1wk after ICL implantation(P<0.05).The patients demonstrated significantly reduced arch height and corneal endothelium cell count 1wk,1,and 3mo after adjusting position compared to 1wk,1,and 3mo after ICL implantation(P<0.05).However,there was no significant difference in refraction between 1wk,1,and 3mo after ICL implantation and position adjustment(P>0.05).CONCLUSION:Early positioning adjustment postphakic ICL implantation can benefit patients with adjusted arch height or higher IOP.Despite the good clinical effects,the doctors should pay attention to the potential for adverse effects on UCVA and corneal endothelium cells following early position adjustment after posterior chamber phakic ICL implantation.

Error induced by the estimation of the corneal power and the effective lens position with a rotationally asymmetric refractive multifocal intraocular lens

AIM : To evaluate the prediction error in intraocular lens(IOL) power calculation for a rotationally asymmetric refractive multifocal IOL and the impact on this error of the optimization of the keratometric estimation of the corneal power and the prediction of the effective lens position(ELP).METHODS: Retrospective study including a total of 25 eyes of 13 patients(age, 50 to 83y) with previous cataract surgery with implantation of the Lentis Mplus LS-312 IOL(Oculentis Gmb H, Germany). In all cases, an adjusted IOL power(P IOLadj) was calculated based on Gaussian optics using a variable keratometric index value(n kadj) for the estimation of the corneal power(P kadj) and on a new value for ELP(ELP adj) obtained by multiple regression analysis.This P IOLadj was compared with the IOL power implanted(P IOLReal) and the value proposed by three conventional formulas(Haigis, Hoffer Q and Holladay Ⅰ).RESULTS: P IOLReal was not significantly different than P IOLadj and Holladay IOL power(P 】0.05). In the Bland and Altman analysis, P IOLadj showed lower mean difference(-0.07 D) and limits of agreement(of 1.47 and-1.61 D)when compared to P IOLReal than the IOL power value obtained with the Holladay formula. Furthermore, ELP adj was significantly lower than ELP calculated with other conventional formulas(P 【0.01) and was found to be dependent on axial length, anterior chamber depth and P kadj. CONCLUSION: Refractive outcomes after cataract surgery with implantation of the multifocal IOL Lentis Mplus LS-312 can be optimized by minimizing thekeratometric error and by estimating ELP using a mathematical expression dependent on anatomical factors.

Influence of lens position as detected by an anterior segment analysis system on postoperative refraction in cataract surgery

AIM:To predict postoperative intraocular lens(IOL)position using the Sirius anterior segment analysis system and investigate the effect of lens position and IOL type on postoperative refraction.METHODS:A total of 97 patients(102 eyes)were enrolled in the final analysis.An anterior segment biometry measurement was performed preoperatively with Sirius and Lenstar.The results of predicted lens position(PLP)and IOL power were automatically calculated by the software used by the instruments.Effective lens position(ELP)was measured manually using Sirius 3 mo postoperatively.Pearson's correlation analysis and linear regression analysis were used to determine the correlation of lens position to other parameters.RESULTS:PLP and ELP were positively correlated to axial length(AL;r=0.42,P<0.0001 and r=0.49,P<0.0001,respectively).There was a weak correlation between the peLP(ELP-PLP)and the prediction error of spherical refraction(peSR;r=0.34,P<0.0001).The peLP of Softec HD IOL differed statistically from those of both the TECNIS ZCB00 and Sensor AR40E IOLs.Multiple linear regression was used to obtain the prediction formula:ELP=0.66+0.63×[aqueous depth(AQD)+0.6 LT](r=0.61,P<0.0001),and a new variable(AQD+0.6 LT)was found to have the strongest correlation with ELP.CONCLUSION:The Sirius anterior segment analysis system is helpful to predict ELP,which reduces postoperative refraction error.

Optomechanical Design for Precision Lens Positioning and Mounting

The proper choice of optomechanical components along with alignment techniques is vital to the successful implementation of lens positioning and mounting. In general, there is a trade-off between lens positioning accuracy and manufacturing cost. In order to achieve optimal precision- to-cost ratio, a careful optomechanical design together with accurate alignment and assembly is necessary. This paper presents a lens positioning and mounting in a few microns accuracy using a kinematic mount module. The optomechanical design of the kinematic mount module and the associated fixtures based on the simulation study of components sensitivity are presented. The processes for alignment and assembly, which separate decenter from tip-tilt, are developed and presented. Finally, the prototypes are created and testing results are presented. The optomechanical design that allows the separation of decenter from tip-tilt considerably simplifies the positioning and assembly process and reduces the cost for mass production.