Effects of iron oxide on crystallization behavior and spatial distribution of spinel in stainless steel slag

Chromium plays a vital role in stainless steel due to its ability to improve the corrosion resistance of the latter.However,the re-lease of chromium from stainless steel slag(SSS)during SSS stockpiling causes detrimental environmental issues.To prevent chromium pollution,the effects of iron oxide on crystallization behavior and spatial distribution of spinel were investigated in this work.The results revealed that FeO was more conducive to the growth of spinels compared with Fe2O3 and Fe3O4.Spinels were found to be mainly distrib-uted at the top and bottom of slag.The amount of spinel phase at the bottom decreased with the increasing FeO content,while that at the top increased.The average particle size of spinel in the slag with 18wt%FeO content was 12.8μm.Meanwhile,no notable structural changes were observed with a further increase in FeO content.In other words,the spatial distribution of spinel changed when the content of iron oxide varied in the range of 8wt%to 18wt%.Finally,less spinel was found at the bottom of slag with a FeO content of 23wt%.

Microwave-assisted exploration of the electron configuration-dependent electrocatalytic urea oxidation activity of 2D porous NiCo_(2)O_(4) spinel

Urea holds promise as an alternative water-oxidation substrate in electrolytic cells.High-valence nickelbased spinel,especially after heteroatom doping,excels in urea oxidation reactions(UOR).However,traditional spinel synthesis methods with prolonged high-temperature reactions lack kinetic precision,hindering the balance between controlled doping and highly active two-dimensional(2D)porous structures design.This significantly impedes the identification of electron configuration-dependent active sites in doped 2D nickel-based spinels.Herein,we present a microwave shock method for the preparation of 2D porous NiCo_(2)O_(4)spinel.Utilizing the transient on-off property of microwave pulses for precise heteroatom doping and 2D porous structural design,non-metal doping(boron,phosphorus,and sulfur)with distinct extranuclear electron disparities serves as straightforward examples for investigation.Precise tuning of lattice parameter reveals the impact of covalent bond strength on NiCo_(2)O_(4)structural stability.The introduced defect levels induce unpaired d-electrons in transition metals,enhancing the adsorption of electron-donating amino groups in urea molecules.Simultaneously,Bode plots confirm the impact mechanism of rapid electron migration caused by reduced band gaps on UOR activity.The prepared phosphorus-doped 2D porous NiCo_(2)O_(4),with optimal electron configuration control,outperforms most reported spinels.This controlled modification strategy advances understanding theoretical structure-activity mechanisms of high-performance 2D spinels in UOR.

Healing the structural defects of spinel MnFe_(2)O_(4) to enhance the electrocatalytic activity for oxygen reduction reaction

Spinel metal oxides containing Mn,Co,or Fe(AB_(2)O_(4),A/B=Mn/Fe/Co)are one of the most promising nonPt electrocatalysts for oxygen reduction reaction(ORR)in alkaline conditions.However,the low conductivity of metal oxides and the poor intrinsic activities of transition metal sites lead to unsatisfactory ORR performance.In this study,eutectic molten salt(EMS)treatment is employed to reconstruct the atomic arrangement of MnFe_(2)O_(4)electrocatalyst as a prototype for enhancing ORR performance.Comprehensive analyses by using XAFS,soft XAS,XPS,and electrochemical methods reveal that the EMS treatment reduces the oxygen vacancies and spinel inverse in MnFe_(2)O_(4)effectively,which improves the electric conductivity and increases the population of more catalytically active Mn^(2+)sites with tetrahedral coordination.Moreover,the enhanced Mn-O interaction after EMS treatment is conducive to the adsorption and activation of O_(2),which promotes the first electron transfer step(generally considered as the ratedetermining step)of the ORR process.As a result,the EMS treated MnFe_(2)O_(4)catalyst delivers a positive shift of 40 mV in the ORR half-wave potential and a two-fold enhanced mass/specific activity.This work provides a convenient approach to manipulate the atomic architecture and local electronic structure of spinel oxides as ORR electrocatalysts and a comprehensive understanding of the structureperformance relationship from the molecular/atomic scale.

Striking Stabilization Effect of Spinel Cobalt Oxide Oxygen Evolution Electrocatalysts in Neutral pH by Dual-Sites Iron Incorporation

Developing stable and efficient nonprecious-metal-based oxygen evolution catalysts in the neutral electrolyte is a challenging but essential goal for various electrochemical systems.Particularly,cobalt-based spinels have drawn a considerable amount of attention but most of them operate in alkali solutions.However,the frequently studied Co-Fe spinel system never exhibits appreciable stability in nonbasic conditions,not to mention attract further investigation on its key structural motif and transition states for activity loss.Herein,we report exceptional stable Co-Fe spinel oxygen evolution catalysts(~30%Fe is optimal)in a neutral electrolyte,owing to its unique metal ion arrangements in the crystal lattice.The introduced iron content enters both the octahedral and tetrahedral sites of the spinel as Fe^(2+)and Fe^(3+)(with Co ions having mixed distribution as well).Combining density functional theory calculations,we find that the introduction of Fe to Co_(3)O_(4)lowers the covalency of metal-oxygen bonds and can help suppress the oxidation of Co^(2+/3+)and 0^(2-).It implies that the Co-Fe spinel will have minor surface reconstruction and less lattice oxygen loss during the oxygen evolution reaction process in comparison with Co_(3)O_(4)and hence show much better stability.These findings suggest that there is still much chance for the spinel structures,especially using reasonable sublattices engineering via multimetal doping to develop advanced oxygen evolution catalysts.

Unveiling the geometric site dependent activity of spinel Co_(3)O_(4)for electrocatalytic chlorine evolution reaction

Spinel cobalt oxide(Co_(3)O_(4)),consisting of tetrahedral Co^(2+)(CoTd)and octahedral Co^(3+)(CoOh),is considered as promising earth-abundant electrocatalyst for chlorine evolution reaction(CER).Identifying the catalytic contribution of geometric Co site in the electrocatalytic CER plays a pivotal role to precisely modulate electronic configuration of active Co sites to boost CER.Herein,combining density functional theory calculations and experiment results assisted with operando analysis,we found that the Co_(Oh) site acts as the main active site for CER in spinel Co_(3)O_(4),which shows better Cl^(-)adsorption and more moderate intermediate adsorption toward CER than CoTd site,and does not undergo redox transition under CER condition at applied potentials.Guided by above findings,the oxygen vacancies were further introduced into the Co_(3)O_(4) to precisely manipulate the electronic configuration of Co_(Oh) to boost Cl^(-)adsorption and optimize the reaction path of CER and thus to enhance the intrinsic CER activity significantly.Our work figures out the importance of geometric configuration dependent CER activity,shedding light on the rational design of advanced electrocatalysts from geometric configuration optimization at the atomic level.

The Spectral Characterization of Blue Spinel and Other Blue Gemstones with the Alexandrite Effect

In gemmology,the term“Alexandrite effect”is used to describe colour change phenomenon when a gemstone is observed under different light sources,usually between daylight and incandescent light.The definition of the Alexandrite effect is constantly being broadened with new discovery of gem resource.The traditional definition of the Alexandrite effect attributing the colour change phenomenon to the presence of two maximum transmission regions and a maximum absorption region in the absorption spectra.In this study,7 blue spinels and 5 blue gemstones(including tanzanite,kyanite,fluorite,and 2 sapphires)showing the Alexandrite effect were investigated.The goal is to explain the cause of blue-to-violet Alexandrite effect and the spectral features causing such colour change.In the UV-Vis spectra,all samples showed a maximum absorption peak in the range of 534-610 nm,within the green region to orange region.The traditional explanation of green to red Alexandrite effect required a transmission window in the red region;however,some of our samples did not show this transmission window and the blue-to-violet Alexandrite effect was still visible.Therefore,it is incomplete to explain the mechanism of the Alexandrite effect according to their characteristic absorption spectra,a systematic study based on modern colour science and colour perception in human vision is required to elucidate the blue-to-violet Alexandrite effect.

Effect of Sc_2O_3 addition on densification and microstructure of different spinelized magnesium aluminate spinels

The densification and microstructure of different spinelized magnesium aluminate spinels（MAS） were studied adding Sc_2O_3 as additive. Sintered products were then characterized in terms of densification, phase analysis, quantitative elemental analysis and microstructure. The results show that Sc_2O_3 is found to be beneficial for the densification of MAS. Sc_2O_3 has a more significant effect on the densification of partially spinelized MAS batch than that of fully spinelized MAS batch. At the sintering temperature of 1650 °C, the bulk density of sintered products of partially spinelized powders increases by 0.243 g/cm3 as the Sc_2O_3 content increases from 0 to 4%（mass fraction） and that of fully spinelized powder increases by 0.14 g/cm3. Compared with the sintered samples prepared from the fully spinelized powder, the sintered samples using the partially spinelized powders as raw materials have more compact microstructures.

固体废弃物铝灰和粉煤灰原位合成Spinel-Sialon复相材料的研究

本文利用铝灰和粉煤灰为原料,经原位铝热还原氮化法合成了Spinel-Sialon复相材料。通过XRD、SEM、EDS等分析手段,研究了合成温度和还原剂铝的添加量对合成产物物相及微观形貌的影响。结果表明:合成Spinel-Sialon的优化工艺参数为铝的添加量为过量100%、合成温度为1550℃,保温时间3 h,合成得到发育良好的柱状β-Sialon及八面体形的镁铝尖晶石。合成温度、还原剂铝的添加量均是影响氮化产物的重要因素。随着温度的升高或还原剂铝的添加量增多,Al2O3越来越少,β-Sialon和镁铝尖晶石均增多,且β-Sialon的Z值增大,MgAl2O4转变成富铝尖晶石。

Al_2O_3-ZrO_2-Spinel三元纳米复相陶瓷超塑性变形及组织演变

采用真空热压烧结工艺制备了三元纳米复相陶瓷并进行了超塑性压缩试验。结果表明:纳米复相陶瓷中的第二相在烧结和变形过程中有效地阻止了基体Al2O3的晶粒长大。在1650℃材料表现出良好的高应变速率超塑变形能力,变形抗力小于30MPa。微观组织观察表明由于变形过程中存在有益压应力,材料变形后晶界处未出现空洞,经变形量为60%的压缩变形后材料中存在较高密度的位错,位错主要存在于尖晶石和氧化锆第二相中,基体Al2O3的晶粒仍为等轴状,表明位错运动对晶界滑移起到了积极地协调作用。

活性CP-Spinel复合生物材料的研究

采用Ｘ射线衍射、扫描电镜和差热分析等手段，研究了钙磷化合物－镁铝尖晶石（ＣＰ－Ｓｐｉｎｅｌ）复合生物材料的微观结构、力学性能和生物学特性。结果表明，Ｓｐｉｎｅｌ的加入显著地提高ＣＰ材料的力学性能，在高温下它还阻止磷酸钙发生相转变，从而保证了该材料的生物活性及适合于人体骨需求的力学性能．ＣＰ－Ｓｐｉｎｅｌ材料具有很好的生物相容性，无毒无刺激性，溶血指数小于２％。

Two-step sintering of magnesium aluminate spinels and their corrosion in Na_3AlF_6-AlF_3-CaF_2-Al_2O_3 bath

New types of refractory materials need to be developed for designing the man-made ledge of the Hall-Heroult cell for aluminum electrolysis, which are currently constructed by frozen ledge.Magnesium aluminate spinel （MAS） as potential candidate materials was prepared by two-step sintering. The densification and grain growth of the MAS wereinvestigatedbytheArchimedes drainage method and scanning electron microscope （SEM）. All the specimens were corroded in aNa3AlF6-AlF3-CaF2-Al2O3bath to assess the corrosion resistance. The results show that a MAS material with a high relative density of 99.2% and ahomogeneous microstructure is achieved under two-step sintering conditions. The corrosion mechanisms of MAS inNa3AlF6-AlF3-CaF2-Al2O3 bathare mainly proposed by dissolution of MAS, formation of aluminum oxide, and diffusion of fluorides. The MAS prepared by two-step sintering exhibits good corrosion resistance to theNa3AlF6-AlF3-CaF2-Al2O3bath.

Spinel增强HAP·TCP复合生物材料研究

采用化学共沉淀法制得羟基磷灰石(HAP)粉和铝镁尖晶石(Spinel)粉,并以HAP粉体和Spinel粉体为原料采用粉末冶金方法制得HAP·TCF-Spinel复合生物材料。采用红外光谱分析、X射线衍射、透射电镜、扫描电镜、金相、力学性能测试和蛋白质吸附实验等对上述合成的材料进行了表征。微观结构表明HAP·TCP与Spinel两相分布均匀,且界面结合良好。该复合材料具有良好的抗弯强度(σ抗弯)和抗压强度(σ抗压)。当HAP的含量为62.5wt％时其抗弯强度和抗压强度分别达到σ抗弯=212MPa,σ抗压=352MPa。蛋白质吸附实验表明,HAP·TCP-S-Spinel复合生物材料对白蛋白和血清蛋白具有较强的吸附能力。

Fabrication and characterization of electrodeposited nanocrystalline Ni-Fe alloys for NiFe_2O_4 spinel coatings

Nanocrystalline Ni-Fe FCC alloy coatings with Fe content of 1.3%-39%（mass fraction） were fabricated on the nickel substrates using a DC electrodeposition technique. The crystal structure, lattice strain, grain size and lattice constant of the Ni-Fe alloy coatings were studied by X-ray diffraction technique. The chemical composition and surface morphology of the FCC Ni-Fe alloy coatings were investigated with the energy dispersive X-ray spectroscopy（EDS） and atomic force microscopy（AFM）. The results show that the Fe content of the Ni-Fe alloy coatings has a great influence on the preferred orientation, grain size, lattice constant and lattice strain. FCC Ni-Fe alloy coatings exhibit preferred orientations of（200） or（200）（111）. With an increase of Fe content, the preferred growth orientation of（200） plane is weakened gradually, while the preferred growth orientation of（111） increases. An increase of the Fe content in the range of 1.3%-25%（mass fraction） results in a significant grain refinement of the coatings. Increasing the Fe content beyond 25% does not decrease the grain size of FCC Ni-Fe alloys further. The lattice strain increases with increasing the Fe content in the FCC Ni-Fe alloys. Since the alloys with Fe content not less than 25% has similar grain size（~11 nm）, the increase in the lattice strain with the increase of Fe content cannot be attributed to the change in the grain size.

无定形Li-Mn-Al-Co-O前驱体制备改性尖晶石锰酸锂

采用水热法合成了无定形Li-Mn-Al-Co-O前驱体,经过后续热处理制备了Al-Co复合掺杂LiMn_2O_4正极材料Li_(1.035)Co_(0.02)Al_(0.025)Mn_(1.92)0O_4,并对其物理及电化学性能进行了测试。SEM、XRD结果表明:Al-Co的掺入对尖晶石锰酸锂的形貌和晶体结构会有微弱影响。电化学测试结果表明:Al-Co掺杂后,材料的循环性能和倍率性能都获得了显著的改善,其在0.5 C下的首次放电容量为113.9 m A.h/g,经过100次循环后比容量保持率仍然有92.4%,8 C下容量依然高达85.5 m A·h/g。

Spinel增强HAP·TCP复合生物材料研究

采用化学共沉淀法制得羟基磷灰石(Ca_(10)(PO_4)_6(OH)_2)粉体和铝镁尖晶石(MgAl_2O_4)粉体,并以羟基磷灰石(HAP)粉体和铝镁尖晶石(Spinel)粉体为原料采用粉末冶金方法制得HAP·TCP-Spinel复合生物材料;采用X射线衍射分析、金相分析、红外光谱分析、烧结收缩性能分析和力学性能测试等对制备的材料进行了表征。研究结果表明:HAP·TCP-Spinel复合生物材料的烧结收缩率约为45％;HAP·TCP与Spine两相分布均匀,且界面结合良好;该复合材料表现出优良的抗弯强度和抗压强度性能;羟基磷灰石的含量为62.5％时该复合材料性能达到最佳,其抗弯强度和抗压强度分别为189MPa和352MPa。

Ni/Al_2O_3 catalysts derived from spinel NiAl_2O_4 for low-temperature hydrogenation of maleic anhydride to succinic anhydride

Ni/Al2O3 catalysts were derived from spinel NiAl2O4 with different Ni content ((2.5, 5 and 7.5) wt%). The catalysts were obtained by H-2 reduction and were investigated for the low-temperature hydrogenation of maleic anhydride (MA) to produce succinic anhydride (SA). The characterization results showed that Ni-0 active sites were mainly derived during the H2 reduction from spinel NiAl2O4 Among the catalysts studied, employing the optimum preparation and reaction conditions with Ni(5%)/Al2O3 yielded the highest catalytic performance. A near-100% conversion of MA and similar to 90% selectivity to SA were achieved at 120 degrees C and 0.5 MPa of H-2 with a weighted hourly space velocity (MA) of 2 h(-1). (C) 2017, Dalian Institute of Chemical Physics, Chinese Academy of Sciences. Published by Elsevier B.V. All rights reserved.

Li-Mn铝硅酸盐系玻璃晶化行为研究

通过XRD、DTA分析,对影响晶化的因素如组成、热处理、晶核剂等进行探讨。研究表明通过增加Li-Mn正硅酸盐比例至50％,可获得良好而均匀的结晶相,同时引入TiO_2晶核剂,可获得更细的粒状结构。

Feasibility of aluminum recovery and MgAl_2O_4 spinel synthesis from secondary aluminum dross

The feasibility of aluminum recovery from secondary aluminum dross by extraction with NaOH solution and the subsequent synthesis of MgAl_2O_4 spinel by sintering the extracted slag were studied. The extraction percentage of soluble aluminum from the dross reached 80% at a temperature of 353 K, liquid-to-solid ratio of 12 mL·g^(-1), stirring speed of 300 r·min^(-1), and an extraction time of 15 min; the hydrolysis percentage of AlN reached 40% with an extraction time of 30 min. The activation energies of the soluble aluminum and AlN extracted from the dross were 7.15 and 8.98 kJ·mol^(-1), respectively, indicating that their kinetics were controlled by outer diffusion without a product layer. The extracted slag was sintered in the temperature range 1373–1773 K; MgAl_2O_4 spinel with a compressive strength as high as 69.4 MPa was produced in the sample sintered at 1673 K for 3 h. This value exceeds the threshold(40 MPa) prescribed by the National Standard for the Magnesia and Magnesia-alumina Refractory Bricks of China(GB/T 2275-2007). These results establish the effectiveness of aluminum recovery from secondary aluminum dross and subsequent MgAl_2O_4 spinel synthesis.

Effect of FeO on the formation of spinel phases and chromium distribution in the CaO-SiO_2-MgO-Al_2O_3-Cr_2O_3 system

Synthetic slag samples of the CaO-SiO2-MgO-A1203-Cr203 system were obtained to clarify the effect of FeO on the formation of spinel phases and Cr distribution. X-ray diffraction （XRD） and scanning electron microscopy （SEM） equipped with energy-dispersive spectroscopy （EDS）, as well as the thermodynamic software FactSage 6.2, were used for sample characterization. The results show that the addition of FeO can decrease the viscosity of molten slag and the precipitation temperatures of melilite and merwinite. The solidus temperature significantly decreases from 1400 to 1250℃ with the increase of FeO content from 0wt% to 6wt%. The addition of FeO could enhance the content of Cr in spinel phases and reduce the content of Cr in soluble minerals, such as merwinite, melilite, and dicalcium silicate. Hence, the addition of FeO is conducive to decreasing Cr leaching.

Spinel lithium titanate (Li_4Ti_5O_(12)) as novel anode material for room-temperature sodium-ion battery

This is the first time that a novel anode material, spinel Li4Ti5O12 which is well known as a ＂zero-strain＂ anode material for lithium storage, has been introduced for sodium-ion battery. The Li4Ti5O12 shows an average Na storage voltage of about 1.0 V and a reversible capacity of about 145 mAh/g, thereby making it a promising anode for sodiumion battery. Ex-situ X-ray diffraction （XRD） is used to investigate the structure change in the Na insertion/deinsertion process. Based on this, a possible Na storage mechanism is proposed.