Transient Rayleigh wave detection is a high-precision nondestructive detection method.At present,it has been widely used in shallow exploration,but rarely used in tunnel lining quality detection.Through the tunnel lin...Transient Rayleigh wave detection is a high-precision nondestructive detection method.At present,it has been widely used in shallow exploration,but rarely used in tunnel lining quality detection.Through the tunnel lining physical model experiment,the layout defects of the double-layer reinforcement lining area were detected and the Rayleigh wave velocity profile and dispersion curve were analyzed after data process-ing,which finally verified the feasibility and accuracy of Rayleigh wave method in detecting the tunnel lining void area.The results show that the method is not affected by the reinforcement inside the lining,the shallow detection is less disturbed and the accuracy is higher,and the data will fluctuate slightly with the deepening of the detection depth.At the same time,this method responds quite accurately to the thickness of the concrete,allowing for the assessment of the tunnel lining’s lack of compactness.This method has high efficiency,good reliability,and simple data processing,and is suitable for nondestructive detection of internal defects of tun-nel lining structure.展开更多
The synchronous construction of the secondary lining during the boring of large-diameter shield faces challenges such as the design of the lining jumbo,the high requirements on the performance for the lining jumbo,the...The synchronous construction of the secondary lining during the boring of large-diameter shield faces challenges such as the design of the lining jumbo,the high requirements on the performance for the lining jumbo,the organization of the construction activities in the small and confined area,the horizontal transportation for shield boring and high safety management requirements.A super-long invert lining construction jumbo,as well as the matching California switch,is developed,which provides solution for the confliction between the invert lining construction and the horizontal transportation.The procedure and method for the synchronous operation of the shield boring and the secondary lining are developed by referring to the synchronous construction of the secondary lining during the boring of the TBMs in hard rocks.Due to the adoption of the synchronous operation of the shield boring and the secondary lining,the construction period is shortened and the construction cost is reduced.The paper can provide reference for the synchronous construction of the secondary lining in similar projects in the future.展开更多
Currently,model tests are increasingly being used to simulate the construction of mountain tunnels,but the support structure of the model tests does not show the composite lining,and the force laws of the composite li...Currently,model tests are increasingly being used to simulate the construction of mountain tunnels,but the support structure of the model tests does not show the composite lining,and the force laws of the composite lining are not yet clear.In this research,the force variation of composite lining under three cases in model tests of deep-buried tunnels were carried out with the surrounding rock grade and installation time as the variation factors.The test results reveal that:(1)The suitable method to reduce the contact load between the secondary lining and primary support is to enhance the primary support in the soft and weak surrounding rock.Correspondingly,for ClassⅢsurrounding rock and better quality of surrounding rock,the primary support can lag behind the excavation face a certain distance.(2)The axial forces of the bolts tend to rise with concentration of 0.4 kN-0.7 kN after the secondary lining was installed.(3)With or without two to three excavation cycles delayed,the load sharing ratio of the secondary lining of the Class III surrounding rock is less than 10%.Finally,the numerical simulation verifies the feasibility of the model tests.展开更多
The numerical simulation results utilizing the Peridynamics(PD)method reveal that the initial crack and crack propagation of the tunnel concrete lining structure agree with the experimental data compared to the Japane...The numerical simulation results utilizing the Peridynamics(PD)method reveal that the initial crack and crack propagation of the tunnel concrete lining structure agree with the experimental data compared to the Japanese prototype lining test.The load structure model takes into account the cracking process and distribution of the lining segment under the influence of local bias pressure and lining thickness.In addition,the influence of preset cracks and lining section formon the crack propagation of the concrete lining model is studied.This study evaluates the stability and sustainability of tunnel structure by the Peridynamics method,which provides a reference for the analysis of the causes of lining cracks,and also lays a foundation for the prevention,reinforcement and repair of tunnel lining cracks.展开更多
The steel lining of huge facilities is a significant structure,which experiences extreme environments and needs to be inspected periodically after manufacture.However,due to the complexity(crisscross welds,curved surf...The steel lining of huge facilities is a significant structure,which experiences extreme environments and needs to be inspected periodically after manufacture.However,due to the complexity(crisscross welds,curved surface,etc.)of their inside environments,high demands for stable adhesion and curvature adaptability are put forward.This paper presents a novel wheeled magnetic adhesion robot with passive suspension applied in nuclear power containment called NuBot,and mainly focuses on the following aspects:(1)proposing the wheeled locomotion suspension to adapt the robot to the uneven surface;(2)implementing the parameter optimization of NuBot.A comprehensive optimization model is established,and global optimal dimensions are properly chosen from performance atlases;(3)determining the normalization factor and actual dimensional parameters by constraints of the steel lining environment;(4)structure design of the overall robot and the magnetic wheels are completed.Experiments show that the robot can achieve precise locomotion on both strong and weak magnetic walls with various inclination angles,and can stably cross the 5 mm weld seam.Besides,its maximum payload capacity reaches 3.6 kg.Results show that the NuBot designed by the proposed systematic method has good comprehensive capabilities of surface-adaptability,adhesion stability,and payload.Besides,the robot can be applied in more ferromagnetic environments and the design method offers guidance for similar wheeled robots with passive suspension.展开更多
In areas with seasonal freezing,when the tunnel lining concrete is saturated with water infiltrating the interior,the lining and the surrounding rocks will simultaneously freeze.However,the current calculation of the ...In areas with seasonal freezing,when the tunnel lining concrete is saturated with water infiltrating the interior,the lining and the surrounding rocks will simultaneously freeze.However,the current calculation of the frost heaving force fails to consider the synchronous damage to the lining and surrounding rocks under freeze-thaw cycles.Therefore,as per the elastic calculation model of the frost heaving force and model of steady-state heat transfer of circular tunnels,this study introduces the frost heaving rate of lining and surrounding rocks.First,the analytical solution of frost heaving force is obtained for simultaneous frost heaving of lining and surrounding rocks under any steady-state temperature field.Then,based on the fracture theory and meso-damage mechanics,the damage variables of lining and surrounding rocks under freeze-thaw cycles are extracted,representing their elastic modulus and porosity.Finally,the formula of frost heaving force for synchronous damage to the lining and surrounding rocks at any steady-state temperature field is obtained.The calculation results demonstrate that the lower the temperature inside the lining,the greater the frost heaving force.With the increasing number of freeze-thaw cycles,frost heaving force tends to gradually increase initially,reaching a peak value at 85 freeze-thaw cycles,decreasing to 80%of the peak value at 140 cycles before reaching a constant value.The lining participates in frost heaving,increasing the frost heaving force.The initial increase rate of frost heaving force is 15.7%.Changing the fitting coefficients s1 and s2 of the lining and surrounding rocks can effectively control the magnitude of the frost heaving force in the tunnels.展开更多
Longitudinal cracks on the tunnel lining significantly influence the performance of tunnels in operation.In this study,we propose a semi-analytical method that provides a simple and effective way to calculate the inte...Longitudinal cracks on the tunnel lining significantly influence the performance of tunnels in operation.In this study,we propose a semi-analytical method that provides a simple and effective way to calculate the internal forces of tunnel linings with multiple cracks.The semi-analytical solution is obtained using structural analysis considering the flexural rigidity for the cracked longitudinal section of the tunnel lining.Then the proposed solution is verified numerically.Using the proposed method,the influences of the crack depth and the number of cracks on the bending moment and modified crack tip stress are investigated.With the increase in crack depth,the bending moment of lining scetion adjacent to the crack decreases,while the bending moment of lining scetion far away from the crack increases slightly.The more the number of cracks in a tunnel lining,the easier the new cracks initiated.展开更多
For long-distance water conveyance shield tunnels in operation,the high internal water pressure may cause excessive deformation of composite linings,affecting their structural integrity and serviceability.However,the ...For long-distance water conveyance shield tunnels in operation,the high internal water pressure may cause excessive deformation of composite linings,affecting their structural integrity and serviceability.However,the deformation and failure characteristics of lining structures under internal water pressure are not well investigated in the literature,particularly for three-layer composite linings.This study presents an in situ experimental investigation on the response of two types of composite linings(i.e.separated and combined lining structures)subjected to internal pressures,in which a fiber optic nerve system(FONS)equipped with distributed strain and displacement sensing nerves was employed to monitor the performance of the two composite linings during testing.The experimental results clearly show that the damage of the tunnel lining under different internal pressures was mainly located in the self-compaction concrete layer.The separated lining structure responded more aggressively to the variations in internal pressures than the combined one.Moreover,two evaluation indices,i.e.radial displacement and effective stiffness coefficient,are proposed for describing the changes in the structural bearing performance.The effective stiffness coefficients of the two types of lining structures were reduced by 39.4%and 29.5%,respectively.Considering the convenience of field monitoring,it is suggested that the average strains at different layers can be used as characteristic parameters for estimating the health conditions of lining structures in service.The analysis results provide a practical reference for the design and health evaluation of water conveyance shield tunnels with composite linings.展开更多
Minimizing of heat loss of liquid steel through the ladle lining led to the integration of increasing insulation function of the permanent lining and high-quality insulating layer between the permanent lining and the ...Minimizing of heat loss of liquid steel through the ladle lining led to the integration of increasing insulation function of the permanent lining and high-quality insulating layer between the permanent lining and the ladle steel shell.In this paper,a study was made on physical and thermomechanical properties and corrosion resistance of calcium hexaluminate based castables.The chemical and physical properties of CA6 based castables fabricated in this work can fulfill general requirements of the permanent lining in ladle.The permanent linings of CA6 based castables offer superb thermal insulation and corrosion resistance,compared to conventional refractory systems of 300t ladle in Baosteel.Both functions of insulation and safety work effectively in whole process of ladle operation.展开更多
Established in 1988, and put integrity, pragmatic, win-win as principle to guide the products’ research and development, production and sales which enjoys high reputation all over the world. Based on domestic and imp...Established in 1988, and put integrity, pragmatic, win-win as principle to guide the products’ research and development, production and sales which enjoys high reputation all over the world. Based on domestic and imported from Germany interlining production line, we have the specialized strong technical force, advanced detection system to guarantee the stability of the product quality Our goods are varied and with complete specifications. The main products as following: shirt fusible interlining, outwear fusible interlining, fashion fusible interlining, fur coating interlining, resin interlining, interlining used for shoes, caps and bags, all kinds of fabric and pocket cloth.展开更多
For preventing and curing the rupture disaster of shaft lining effectively, according to the additional force theory of shaft lining fracture, more than forty tests were carried out on the large scale test rig on the ...For preventing and curing the rupture disaster of shaft lining effectively, according to the additional force theory of shaft lining fracture, more than forty tests were carried out on the large scale test rig on the basis of simulating theory. The influence of the position of aquifer, the reinforcing scope of aquifer, reinforcing distance and the strength of grouting cemented mixture on the value and variation law of the axial additional force on shaft lining is studied. The relationships between the reinforcing parameters and the axial additional force on shaft lining are obtained, which provides the theoretic foundation and construction design parameters for the method of reinforcing strata by grouting to prevent and cure tbe rupture disaster of shart lining.展开更多
A new unified analytical solution is presented for predicting the range of plastic zone and stress distributions around a deep circular tunnel in a homogeneous isotropic continuous medium. The rock mass, grouting zone...A new unified analytical solution is presented for predicting the range of plastic zone and stress distributions around a deep circular tunnel in a homogeneous isotropic continuous medium. The rock mass, grouting zone and lining are assumed as elastic-perfectly plastic and governed by the unified strength theory(UST). This new solution has made it possible to consider the interaction between seepage pressure, lining, grouting and rock mass, and the intermediate principal stress effect together. Moreover, parametric analysis is carried out to identify the influence of the related parameters on the plastic zone radius. Under the given conditions, the results show that the plastic zone radius decreases with an increasing cohesion, internal friction angle and hydraulic conductivity of lining and unified failure criterion parameter, respectively; whereas the plastic zone radius increases with the growth of elasticity modulus of lining. Comparison of results from the new solution and the other published one shows well agreement and provides confidence in the new solution proposed.展开更多
Following tunnel excavation and lining completion,fractured surrounding rock deforms gradually over time;this results in a time-dependent evolution of the pressure applied to the lining structure by the surrounding ro...Following tunnel excavation and lining completion,fractured surrounding rock deforms gradually over time;this results in a time-dependent evolution of the pressure applied to the lining structure by the surrounding rock.Thus,the safety of the tunnel lining in weak strata is strongly correlated with time.In this study,we developed an analytical method for determining the time-dependent pressure in the surrounding rock and lining structure of a circular tunnel under a hydrostatic stress field.Under the proposed method,the stress–strain relationship of the fractured surrounding rock is assumed to conform to that of the Burgers viscoelastic component,and the lining structure is assumed to be an elastomer.Based on these assumptions,the viscoelastic deformation of the surrounding rock,the elastic deformation of the lining structure,and the coordinated deformation between the surrounding rock and lining structure were derived.The proposed analytical method,which employs a time-dependent safety coefficient,was subsequently used to estimate the durability of the lining structure of the Foling Tunnel in China.The derived attenuation curve of the safety coefficient with respect to time can assist engineers in predicting the remaining viable life of the lining structure.Unlike existing analytical methods,the method derived in this study considers the time dependency of the interaction between the surrounding rock and tunnel lining;hence,it is more suitable for the evaluation of lining lifetime.展开更多
The mass transfer among the multiphase interactions among the steel, slag, lining refractory, and nonmetallic inclusions during the refining process of a bearing steel was studied using laboratory experiments and nume...The mass transfer among the multiphase interactions among the steel, slag, lining refractory, and nonmetallic inclusions during the refining process of a bearing steel was studied using laboratory experiments and numerical kinetic prediction. Experiments on the system with and without the slag phase were carried out to evaluate the influence of the refractory and the slag on the mass transfer. A mathematical model coupled the ion and molecule coexistence theory, coupled-reaction model, and the surface renewal theory was established to predict the dynamic mass transfer and composition transformation of the steel, the slag, and nonmetallic inclusions in the steel. During the refining process,Al_(2)O_(3) inclusions transformed into Mg O inclusions owing to the mass transfer of [Mg] at the steel/refractory interface and(Mg O) at the slag/refractory interface. Most of the aluminum involved in the transport entered the slag and a small part of the aluminum transferred to lining refractory, forming the Al_(2)O_(3) or Mg O·Al_(2)O_(3). The slag had a significant acceleration effect on the mass transfer. The mass transfer rate(or the reaction rate) of the system with the slag was approximately 5 times larger than that of the system without the slag. In the first 20 min of the refining, rates of magnesium mass transfer at the steel/inclusion interface, steel/refractory interface, and steel/slag interface were x, 1.1 x, and 2.2 x,respectively. The composition transformation of inclusions and the mass transfer of magnesium and aluminum in the steel were predicted with an acceptable accuracy using the established kinetic model.展开更多
The model of skaft lining under force is developed on the basis of the special stratum condition led to sbart cracking- The model is broken into 3 sub-questions to solve separately. According to the principle of super...The model of skaft lining under force is developed on the basis of the special stratum condition led to sbart cracking- The model is broken into 3 sub-questions to solve separately. According to the principle of superposition and strain compatibility, a second kind Fredholm integral equation is generated.A theoretical solution to vertical additional force on shaft lining is obtained by numerical method to the integral equation.展开更多
Numerical simulation was used to estimate the temperature field within a poured concrete,mono-layer freezing-shaft lining.The affects from various factors were investigated.The maximum temperature within the lining in...Numerical simulation was used to estimate the temperature field within a poured concrete,mono-layer freezing-shaft lining.The affects from various factors were investigated.The maximum temperature within the lining increases as the lining thickness increases,decreases as the soil-side wall temperature decreases,decreases as the air temperature inside the shaft decreases and decreases as the air velocity inside the shaft increases.The compression speed of an insulating foam layer affects the maximum temperature difference between the interior and the sidewalls.The maximum temperature difference between the interior and the sidewalls approaches or exceeds the maximum allowable for the curing of poured concrete structures.Attention should be paid to the question of the lining cracking during the curing period.The temperature gradient in the vertical direction may be minimized by preventing air contact against the steel connection board supporting the base of the freshly poured section.展开更多
Lining craze, as a common engineering damage, affects the bearing capacity and the safety of tunnels.To improve the capabilities of the surface crack detection in the tunnel lining, ground penetrating radar(GPR) was e...Lining craze, as a common engineering damage, affects the bearing capacity and the safety of tunnels.To improve the capabilities of the surface crack detection in the tunnel lining, ground penetrating radar(GPR) was employed. The principle and method of GPR for cracks investigation of tunnel lining were expounded. As an application example, some field measurements in order to detect the depth of cracks for the tunnel lining were achieved in a new tunnel. All GPR investigations were made with the antennae of 1 GHz. The cracks of concrete structure were located, and the distributing and depth of cracks are inspected and estimated by GPR. The results of investigation show GPR is accurate and efficient to detect cracks of tunnel lining.展开更多
Subsea tunnel lining structures should be designed to sustain the loads transmitted from surrounding ground and groundwater during excavation. Extremely high pore-water pressure reduces the effective strength of the c...Subsea tunnel lining structures should be designed to sustain the loads transmitted from surrounding ground and groundwater during excavation. Extremely high pore-water pressure reduces the effective strength of the country rock that surrounds a tunnel, thereby lowering the arching effect and stratum stability of the structure. In this paper, the mechanical behavior and shape optimization of the lining structure for the Xiang'an tunnel excavated in weathered slots are examined. Eight cross sections with different geometric parameters are adopted to study the mechanical behavior and shape optimization of the lining structure. The hyperstatic reaction method is used through finite element analysis software ANSYS. The mechanical behavior of the lining structure is evidently affected by the geometric parameters of crosssectional shape. The minimum safety factor of the lining structure elements is set to be the objective function. The efficient tunnel shape to maximize the minimum safety factor is identified. The minimum safety factor increases significantly after optimization. The optimized cross section significantly improves the mechanical characteristics of the lining structure and effectively reduces its deformation. Force analyses of optimization process and program are conducted parametrically so that the method can be applied to the optimization design of other similar structures. The results obtained from this study enhance our understanding of the mechanical behavior of the lining structure for subsea tunnels. These results are also beneficial to the optimal design of lining structures in general.展开更多
In order to study the production of porous silica compacts by the combustion of rice husk ash (RHA) for tundish lining, the experimental design technique was used to evaluate the effect of firing temperature, soakin...In order to study the production of porous silica compacts by the combustion of rice husk ash (RHA) for tundish lining, the experimental design technique was used to evaluate the effect of firing temperature, soaking time and compaction pressure on controlling both the porosity degree and compressive strength of rice husk ash compacts. The results revealed that while the porosity degree of the compacts decreased with the increase in the entire studied parameters, the compressive strength exhibited another trend especially at a lower soaking time. At a lower soaking time, the increase in firing temperature led to a slight decrease in compressive strength and then increasing thereafter. The porous silica compacts having 30% porosity and 〉 2.5 MPa compressive strength suitable for tundish lining could be obtained from the combustion of rice husk ash compacts.展开更多
In this study, the finite element numerical modelling of 2D shaft sections in a Hoek–Brown medium are carried out in a non-hydrostatic stress state in an attempt to predict pressures developing around mine shafts. An...In this study, the finite element numerical modelling of 2D shaft sections in a Hoek–Brown medium are carried out in a non-hydrostatic stress state in an attempt to predict pressures developing around mine shafts. An iterative process of applying support pressure until observing no failure zone around the shaft is used to simulate the required lining support pressure for different shaft models. Later, regression analysis is carried out to find a generic shaft pressure equation representing the rock mass and the stress state. Finally, the developed pressure equation which shows a good agreement with a case study is used in elastic ‘‘thick-walled cylinder" equation to calculate the lining thickness required to prevent the development of a failure zone around the shaft. At the end of the study, a user-friendly object-oriented computer program ‘‘Shaft 2D" is developed to simplify the rigorous shaft lining thickness calculation process.展开更多
基金Supported by Project of Natural Science Foundation of Jilin Province(No.20220101172JC).
文摘Transient Rayleigh wave detection is a high-precision nondestructive detection method.At present,it has been widely used in shallow exploration,but rarely used in tunnel lining quality detection.Through the tunnel lining physical model experiment,the layout defects of the double-layer reinforcement lining area were detected and the Rayleigh wave velocity profile and dispersion curve were analyzed after data process-ing,which finally verified the feasibility and accuracy of Rayleigh wave method in detecting the tunnel lining void area.The results show that the method is not affected by the reinforcement inside the lining,the shallow detection is less disturbed and the accuracy is higher,and the data will fluctuate slightly with the deepening of the detection depth.At the same time,this method responds quite accurately to the thickness of the concrete,allowing for the assessment of the tunnel lining’s lack of compactness.This method has high efficiency,good reliability,and simple data processing,and is suitable for nondestructive detection of internal defects of tun-nel lining structure.
文摘The synchronous construction of the secondary lining during the boring of large-diameter shield faces challenges such as the design of the lining jumbo,the high requirements on the performance for the lining jumbo,the organization of the construction activities in the small and confined area,the horizontal transportation for shield boring and high safety management requirements.A super-long invert lining construction jumbo,as well as the matching California switch,is developed,which provides solution for the confliction between the invert lining construction and the horizontal transportation.The procedure and method for the synchronous operation of the shield boring and the secondary lining are developed by referring to the synchronous construction of the secondary lining during the boring of the TBMs in hard rocks.Due to the adoption of the synchronous operation of the shield boring and the secondary lining,the construction period is shortened and the construction cost is reduced.The paper can provide reference for the synchronous construction of the secondary lining in similar projects in the future.
基金the Scientific Research Project of Zhejiang Provincial Transportation Department(2021050)for the preparation of this manuscript。
文摘Currently,model tests are increasingly being used to simulate the construction of mountain tunnels,but the support structure of the model tests does not show the composite lining,and the force laws of the composite lining are not yet clear.In this research,the force variation of composite lining under three cases in model tests of deep-buried tunnels were carried out with the surrounding rock grade and installation time as the variation factors.The test results reveal that:(1)The suitable method to reduce the contact load between the secondary lining and primary support is to enhance the primary support in the soft and weak surrounding rock.Correspondingly,for ClassⅢsurrounding rock and better quality of surrounding rock,the primary support can lag behind the excavation face a certain distance.(2)The axial forces of the bolts tend to rise with concentration of 0.4 kN-0.7 kN after the secondary lining was installed.(3)With or without two to three excavation cycles delayed,the load sharing ratio of the secondary lining of the Class III surrounding rock is less than 10%.Finally,the numerical simulation verifies the feasibility of the model tests.
基金supported by the National Natural Science Foundation of China (52079128).
文摘The numerical simulation results utilizing the Peridynamics(PD)method reveal that the initial crack and crack propagation of the tunnel concrete lining structure agree with the experimental data compared to the Japanese prototype lining test.The load structure model takes into account the cracking process and distribution of the lining segment under the influence of local bias pressure and lining thickness.In addition,the influence of preset cracks and lining section formon the crack propagation of the concrete lining model is studied.This study evaluates the stability and sustainability of tunnel structure by the Peridynamics method,which provides a reference for the analysis of the causes of lining cracks,and also lays a foundation for the prevention,reinforcement and repair of tunnel lining cracks.
基金Supported by Shanghai Nuclear Star Nuclear Power Technology Co.,Ltd,National Natural Science Foundation of China(Grant No.51735009)State Key Lab of Mechanical System and Vibration Project(Grant No.MSVZD202008).
文摘The steel lining of huge facilities is a significant structure,which experiences extreme environments and needs to be inspected periodically after manufacture.However,due to the complexity(crisscross welds,curved surface,etc.)of their inside environments,high demands for stable adhesion and curvature adaptability are put forward.This paper presents a novel wheeled magnetic adhesion robot with passive suspension applied in nuclear power containment called NuBot,and mainly focuses on the following aspects:(1)proposing the wheeled locomotion suspension to adapt the robot to the uneven surface;(2)implementing the parameter optimization of NuBot.A comprehensive optimization model is established,and global optimal dimensions are properly chosen from performance atlases;(3)determining the normalization factor and actual dimensional parameters by constraints of the steel lining environment;(4)structure design of the overall robot and the magnetic wheels are completed.Experiments show that the robot can achieve precise locomotion on both strong and weak magnetic walls with various inclination angles,and can stably cross the 5 mm weld seam.Besides,its maximum payload capacity reaches 3.6 kg.Results show that the NuBot designed by the proposed systematic method has good comprehensive capabilities of surface-adaptability,adhesion stability,and payload.Besides,the robot can be applied in more ferromagnetic environments and the design method offers guidance for similar wheeled robots with passive suspension.
基金the support of the National Natural Science Foundation of China(Grant Nos.42207199,52179113,42272333)Zhejiang Postdoctoral Scientific Research Project(Grant Nos.ZJ2022155,ZJ2022156)。
文摘In areas with seasonal freezing,when the tunnel lining concrete is saturated with water infiltrating the interior,the lining and the surrounding rocks will simultaneously freeze.However,the current calculation of the frost heaving force fails to consider the synchronous damage to the lining and surrounding rocks under freeze-thaw cycles.Therefore,as per the elastic calculation model of the frost heaving force and model of steady-state heat transfer of circular tunnels,this study introduces the frost heaving rate of lining and surrounding rocks.First,the analytical solution of frost heaving force is obtained for simultaneous frost heaving of lining and surrounding rocks under any steady-state temperature field.Then,based on the fracture theory and meso-damage mechanics,the damage variables of lining and surrounding rocks under freeze-thaw cycles are extracted,representing their elastic modulus and porosity.Finally,the formula of frost heaving force for synchronous damage to the lining and surrounding rocks at any steady-state temperature field is obtained.The calculation results demonstrate that the lower the temperature inside the lining,the greater the frost heaving force.With the increasing number of freeze-thaw cycles,frost heaving force tends to gradually increase initially,reaching a peak value at 85 freeze-thaw cycles,decreasing to 80%of the peak value at 140 cycles before reaching a constant value.The lining participates in frost heaving,increasing the frost heaving force.The initial increase rate of frost heaving force is 15.7%.Changing the fitting coefficients s1 and s2 of the lining and surrounding rocks can effectively control the magnitude of the frost heaving force in the tunnels.
基金The authors gratefully acknowledge the financial support by the Key Project of High-speed Rail Joint Fund of National Natural Science Foundation of China(Grant No.U1934210)the Natural Science Foundation of Beijing,China(Grant No.8202037).
文摘Longitudinal cracks on the tunnel lining significantly influence the performance of tunnels in operation.In this study,we propose a semi-analytical method that provides a simple and effective way to calculate the internal forces of tunnel linings with multiple cracks.The semi-analytical solution is obtained using structural analysis considering the flexural rigidity for the cracked longitudinal section of the tunnel lining.Then the proposed solution is verified numerically.Using the proposed method,the influences of the crack depth and the number of cracks on the bending moment and modified crack tip stress are investigated.With the increase in crack depth,the bending moment of lining scetion adjacent to the crack decreases,while the bending moment of lining scetion far away from the crack increases slightly.The more the number of cracks in a tunnel lining,the easier the new cracks initiated.
基金This work was financially supported by the National Natural Science Foundation of China(Grant Nos.42225702 and 42077235)the Postgraduate Research&Practice Innovation Program of Jiangsu Province,China(Grant No.KYCX22_0162)the scientific research project of Guangdong Yue Hai Pearl River Delta Water Supply Co.,Ltd.The authors thank Guangqing Wei,Lixiang Jia,and Zhen Zhang,all of Suzhou Nanzee Sensing Co.,Ltd.,for their assistance in the tests.The valuable suggestions provided by Professor Baojun Wang,Nanjing University,are also gratefully acknowledged.
文摘For long-distance water conveyance shield tunnels in operation,the high internal water pressure may cause excessive deformation of composite linings,affecting their structural integrity and serviceability.However,the deformation and failure characteristics of lining structures under internal water pressure are not well investigated in the literature,particularly for three-layer composite linings.This study presents an in situ experimental investigation on the response of two types of composite linings(i.e.separated and combined lining structures)subjected to internal pressures,in which a fiber optic nerve system(FONS)equipped with distributed strain and displacement sensing nerves was employed to monitor the performance of the two composite linings during testing.The experimental results clearly show that the damage of the tunnel lining under different internal pressures was mainly located in the self-compaction concrete layer.The separated lining structure responded more aggressively to the variations in internal pressures than the combined one.Moreover,two evaluation indices,i.e.radial displacement and effective stiffness coefficient,are proposed for describing the changes in the structural bearing performance.The effective stiffness coefficients of the two types of lining structures were reduced by 39.4%and 29.5%,respectively.Considering the convenience of field monitoring,it is suggested that the average strains at different layers can be used as characteristic parameters for estimating the health conditions of lining structures in service.The analysis results provide a practical reference for the design and health evaluation of water conveyance shield tunnels with composite linings.
文摘Minimizing of heat loss of liquid steel through the ladle lining led to the integration of increasing insulation function of the permanent lining and high-quality insulating layer between the permanent lining and the ladle steel shell.In this paper,a study was made on physical and thermomechanical properties and corrosion resistance of calcium hexaluminate based castables.The chemical and physical properties of CA6 based castables fabricated in this work can fulfill general requirements of the permanent lining in ladle.The permanent linings of CA6 based castables offer superb thermal insulation and corrosion resistance,compared to conventional refractory systems of 300t ladle in Baosteel.Both functions of insulation and safety work effectively in whole process of ladle operation.
文摘Established in 1988, and put integrity, pragmatic, win-win as principle to guide the products’ research and development, production and sales which enjoys high reputation all over the world. Based on domestic and imported from Germany interlining production line, we have the specialized strong technical force, advanced detection system to guarantee the stability of the product quality Our goods are varied and with complete specifications. The main products as following: shirt fusible interlining, outwear fusible interlining, fashion fusible interlining, fur coating interlining, resin interlining, interlining used for shoes, caps and bags, all kinds of fabric and pocket cloth.
文摘For preventing and curing the rupture disaster of shaft lining effectively, according to the additional force theory of shaft lining fracture, more than forty tests were carried out on the large scale test rig on the basis of simulating theory. The influence of the position of aquifer, the reinforcing scope of aquifer, reinforcing distance and the strength of grouting cemented mixture on the value and variation law of the axial additional force on shaft lining is studied. The relationships between the reinforcing parameters and the axial additional force on shaft lining are obtained, which provides the theoretic foundation and construction design parameters for the method of reinforcing strata by grouting to prevent and cure tbe rupture disaster of shart lining.
基金Project(51378309)supported by National Natural Science Foundation of China
文摘A new unified analytical solution is presented for predicting the range of plastic zone and stress distributions around a deep circular tunnel in a homogeneous isotropic continuous medium. The rock mass, grouting zone and lining are assumed as elastic-perfectly plastic and governed by the unified strength theory(UST). This new solution has made it possible to consider the interaction between seepage pressure, lining, grouting and rock mass, and the intermediate principal stress effect together. Moreover, parametric analysis is carried out to identify the influence of the related parameters on the plastic zone radius. Under the given conditions, the results show that the plastic zone radius decreases with an increasing cohesion, internal friction angle and hydraulic conductivity of lining and unified failure criterion parameter, respectively; whereas the plastic zone radius increases with the growth of elasticity modulus of lining. Comparison of results from the new solution and the other published one shows well agreement and provides confidence in the new solution proposed.
基金supported by the National Natural Science Foundation of China(Nos.71631007 and 71771020)。
文摘Following tunnel excavation and lining completion,fractured surrounding rock deforms gradually over time;this results in a time-dependent evolution of the pressure applied to the lining structure by the surrounding rock.Thus,the safety of the tunnel lining in weak strata is strongly correlated with time.In this study,we developed an analytical method for determining the time-dependent pressure in the surrounding rock and lining structure of a circular tunnel under a hydrostatic stress field.Under the proposed method,the stress–strain relationship of the fractured surrounding rock is assumed to conform to that of the Burgers viscoelastic component,and the lining structure is assumed to be an elastomer.Based on these assumptions,the viscoelastic deformation of the surrounding rock,the elastic deformation of the lining structure,and the coordinated deformation between the surrounding rock and lining structure were derived.The proposed analytical method,which employs a time-dependent safety coefficient,was subsequently used to estimate the durability of the lining structure of the Foling Tunnel in China.The derived attenuation curve of the safety coefficient with respect to time can assist engineers in predicting the remaining viable life of the lining structure.Unlike existing analytical methods,the method derived in this study considers the time dependency of the interaction between the surrounding rock and tunnel lining;hence,it is more suitable for the evaluation of lining lifetime.
基金financially supported by the National Natural Science Foundation China(Nos.U1860206,51725402,and 51874032)the Fundamental Research Funds for the Central Universities(Nos.FRF-TP-19-037A2Z and FRFBD-20-04A)+2 种基金the S&T Program of Hebei,China(No.20311006D)the High Steel Center(HSC)at Yanshan University,Chinathe High Quality Steel Consortium(HQSC)at University of Science and Technology Beijing,China。
文摘The mass transfer among the multiphase interactions among the steel, slag, lining refractory, and nonmetallic inclusions during the refining process of a bearing steel was studied using laboratory experiments and numerical kinetic prediction. Experiments on the system with and without the slag phase were carried out to evaluate the influence of the refractory and the slag on the mass transfer. A mathematical model coupled the ion and molecule coexistence theory, coupled-reaction model, and the surface renewal theory was established to predict the dynamic mass transfer and composition transformation of the steel, the slag, and nonmetallic inclusions in the steel. During the refining process,Al_(2)O_(3) inclusions transformed into Mg O inclusions owing to the mass transfer of [Mg] at the steel/refractory interface and(Mg O) at the slag/refractory interface. Most of the aluminum involved in the transport entered the slag and a small part of the aluminum transferred to lining refractory, forming the Al_(2)O_(3) or Mg O·Al_(2)O_(3). The slag had a significant acceleration effect on the mass transfer. The mass transfer rate(or the reaction rate) of the system with the slag was approximately 5 times larger than that of the system without the slag. In the first 20 min of the refining, rates of magnesium mass transfer at the steel/inclusion interface, steel/refractory interface, and steel/slag interface were x, 1.1 x, and 2.2 x,respectively. The composition transformation of inclusions and the mass transfer of magnesium and aluminum in the steel were predicted with an acceptable accuracy using the established kinetic model.
文摘The model of skaft lining under force is developed on the basis of the special stratum condition led to sbart cracking- The model is broken into 3 sub-questions to solve separately. According to the principle of superposition and strain compatibility, a second kind Fredholm integral equation is generated.A theoretical solution to vertical additional force on shaft lining is obtained by numerical method to the integral equation.
基金provided by the Office of National Science and Technology (No.2006BAB16B01)the Physics Program of the Henan Province Education Department (No.2009B 560004)the Doctoral Fund of Henan Polytechnic University (No.648234)
文摘Numerical simulation was used to estimate the temperature field within a poured concrete,mono-layer freezing-shaft lining.The affects from various factors were investigated.The maximum temperature within the lining increases as the lining thickness increases,decreases as the soil-side wall temperature decreases,decreases as the air temperature inside the shaft decreases and decreases as the air velocity inside the shaft increases.The compression speed of an insulating foam layer affects the maximum temperature difference between the interior and the sidewalls.The maximum temperature difference between the interior and the sidewalls approaches or exceeds the maximum allowable for the curing of poured concrete structures.Attention should be paid to the question of the lining cracking during the curing period.The temperature gradient in the vertical direction may be minimized by preventing air contact against the steel connection board supporting the base of the freshly poured section.
基金Projects(50204012 50490274) supported by the National Natural Science Foundation of China project supported by the Postdoctoral Science Foundation of China
文摘Lining craze, as a common engineering damage, affects the bearing capacity and the safety of tunnels.To improve the capabilities of the surface crack detection in the tunnel lining, ground penetrating radar(GPR) was employed. The principle and method of GPR for cracks investigation of tunnel lining were expounded. As an application example, some field measurements in order to detect the depth of cracks for the tunnel lining were achieved in a new tunnel. All GPR investigations were made with the antennae of 1 GHz. The cracks of concrete structure were located, and the distributing and depth of cracks are inspected and estimated by GPR. The results of investigation show GPR is accurate and efficient to detect cracks of tunnel lining.
基金financially supported by the National Natural Science Foundation of China(Grant No.51308012)the Key Laboratory of Transportation Tunnel Engineering+1 种基金Ministry of EducationSouthwest Jiaotong University(Grant No.TTE2014-06)
文摘Subsea tunnel lining structures should be designed to sustain the loads transmitted from surrounding ground and groundwater during excavation. Extremely high pore-water pressure reduces the effective strength of the country rock that surrounds a tunnel, thereby lowering the arching effect and stratum stability of the structure. In this paper, the mechanical behavior and shape optimization of the lining structure for the Xiang'an tunnel excavated in weathered slots are examined. Eight cross sections with different geometric parameters are adopted to study the mechanical behavior and shape optimization of the lining structure. The hyperstatic reaction method is used through finite element analysis software ANSYS. The mechanical behavior of the lining structure is evidently affected by the geometric parameters of crosssectional shape. The minimum safety factor of the lining structure elements is set to be the objective function. The efficient tunnel shape to maximize the minimum safety factor is identified. The minimum safety factor increases significantly after optimization. The optimized cross section significantly improves the mechanical characteristics of the lining structure and effectively reduces its deformation. Force analyses of optimization process and program are conducted parametrically so that the method can be applied to the optimization design of other similar structures. The results obtained from this study enhance our understanding of the mechanical behavior of the lining structure for subsea tunnels. These results are also beneficial to the optimal design of lining structures in general.
文摘In order to study the production of porous silica compacts by the combustion of rice husk ash (RHA) for tundish lining, the experimental design technique was used to evaluate the effect of firing temperature, soaking time and compaction pressure on controlling both the porosity degree and compressive strength of rice husk ash compacts. The results revealed that while the porosity degree of the compacts decreased with the increase in the entire studied parameters, the compressive strength exhibited another trend especially at a lower soaking time. At a lower soaking time, the increase in firing temperature led to a slight decrease in compressive strength and then increasing thereafter. The porous silica compacts having 30% porosity and 〉 2.5 MPa compressive strength suitable for tundish lining could be obtained from the combustion of rice husk ash compacts.
文摘In this study, the finite element numerical modelling of 2D shaft sections in a Hoek–Brown medium are carried out in a non-hydrostatic stress state in an attempt to predict pressures developing around mine shafts. An iterative process of applying support pressure until observing no failure zone around the shaft is used to simulate the required lining support pressure for different shaft models. Later, regression analysis is carried out to find a generic shaft pressure equation representing the rock mass and the stress state. Finally, the developed pressure equation which shows a good agreement with a case study is used in elastic ‘‘thick-walled cylinder" equation to calculate the lining thickness required to prevent the development of a failure zone around the shaft. At the end of the study, a user-friendly object-oriented computer program ‘‘Shaft 2D" is developed to simplify the rigorous shaft lining thickness calculation process.