Empirical Thermal Investigation of Oil-Immersed Distribution Transformer under Various Loading Conditions

The distribution transformer is the mainstay of the power system.Its internal temperature study is desirable for its safe operation in the power system.The purpose of the present study is to determine direct comprehensive thermal distribution in the distribution transformers for different loading conditions.To achieve this goal,the temperature distribution in the oil,core,and windings are studied at each loading.An experimental study is performed with a 10/0.38 kV,10 kVA oil–immersed transformer equipped with forty–two PT100 sensors(PTs)for temperature measurement installed inside during its manufacturing process.All possible locations for the hottest spot temperature(HST)are considered that made by finite element analysis(FEA)simulation and losses calculations.A resistive load is made to achieve 80%to 120%loading of the test transformer for this experiment.Working temperature is measured in each part of the transformer at all provided loading conditions.It is observed that temperature varies with loading throughout the transformer,and a detailed map of temperature is obtained in the whole test transformer.From these results,the HST stays in the critical section of the primary winding at all loading conditions.This work is helpful to understand the complete internal temperature layout and the location of the HST in distribution transformers.

Experimental and modelling studies of the transient tribological behaviour of a two-phase lubricant under complex loading conditions

The transient tribological phenomenon and premature lubricant breakdown have been widely observed in metal forming,leading to excessive friction at the contact interfaces.In this research,the transient tribological behaviour of a two-phase lubricant were studied under complex loading conditions,featuring abrupt interfacial temperature,contact load,and sliding speed changes,thus representing the severe interfacial conditions observed in warm/hot metal forming applications.The strong experimental evidence indicates that the evolution of friction was attributed to the physical diminution and chemical decomposition effects.As such,a visco-mechanochemical interactive friction model was developed to accurately predict the transient tribological behaviour of the two-phase lubricant under complex loading conditions.The new friction model exhibited close agreements between the modelling and experimental results.

An enhanced damage plasticity model for predicting the cyclic behavior of plain concrete under multiaxial loading conditions

Some of the current concrete damage plasticity models in the literature employ a single damage variable for both the tension and compression regimes,while a few more advanced models employ two damage variables.Models with a single variable have an inherent dificulty in accounting for the damage accrued due to tensile and compressive actions in appropriately different manners,and their mutual dependencies.In the current models that adopt two damage variables,the independence of these damage variables during cyclic loading results in the failure to capture the effects of tensile damage on the compressive behavior of concrete and vice-versa.This study presents a cyclic model established by extending an existing monotonic constitutive model.The model describes the cyclic behavior of concrete under multiaxial loading conditions and considers the influence of tensile/compressive damage on the compressive/tensile response.The proposed model,dubbed the enhanced concrete damage plasticity model(ECDPM),is an extension of an existing model that combines the theories of classical plasticity and continuum damage mechanics.Unlike most prior studies on models in the same category,the performance of the proposed ECDPM is evaluated using experimental data on concrete specimens at the material level obtained under cyclic multiaxial loading conditions including uniaxial tension and confined compression.The performance of the model is observed to be satisfactory.Furthermore,the superiority of ECDPM over three previously proposed constitutive models is demonstrated through comparisons with the results of a uniaxial tension-compression test and a virtual test.

Research of Interaction Force Coefficients Based on Model Test in Loading Condition

It is very difficult,for the component-type ship mathematical model,to estimate the interaction force coefficients among the hull,propeller and rudder. Some coefficients such as wake fraction and flow straightening coefficient were studied from the model tests in diffierent loading conditions and the normal force of rudder was tested in captive model tests to obtain the coefficients. From these results of the tests,the flow straightening coefficients increase with the increase of trims or drafts. Similarly,wake fraction coefficients are larger for the large drafts,however,become small as the trims increase. The resistance is obviously different in fully loaded condition with the trims by stern,however ,the difference is not evident when the draft decreases and the bulbous bow is above the water surface.

Experimental Measurements of the Sensitivity of Fiber-optic Bragg Grating Sensors with a Soft Polymeric Coating under Mechanical Loading,Thermal and Magnetic under Cryogenic Conditions

The strain and temperature sensing performance of fiber-optic Bragg gratings （FBGs） with soft polymeric coating, which can be used to sense internal strain in superconducting coils, are evaluated under variable cryogenic field and magnetic field. The response to a temperature and strain change of coated-soft polymeric FBGs is tested by comparing with those of coated-metal FBGs. The results indicate that the coated-soft polymeric FBGs can freely detect temperature and thermal strain, their At variable magnetic field, the tested results indicate accuracy and repeatability are also discussed in detail. that the cross-coupling effects of FBGs with different matrixes are not negligible to measure electromagnetic strain during fast excitation. The present results are expected to be able to provide basis measurements on the strain of pulsed superconducting magnet/cable （cable- around-conduit conductors, cable-in-conduit conductors）, independently or utilized together with other strain measurement methods.

Determination of Dynamic Load Condition of Aircraft Carrier based on Multivariable Distribution of Flight Parameters

In order to solve the design problem of dynamic load of a carrier-based aircraft,according to the relevant criteria of national military standards,eight key flight parameters of the dynamic load conditions for the aircraft carrier were selected.Based on the multivariable distribution data of landing flight parameters obtained from flight test,the distribution form and range limitation of each flight parameter were determined by using the probability distribution of each flight parameter and the spatial relationship among variables.Furthermore,100000 sets of data were constructed to simulate the landing condition of aircraft in the form of random number.After the envelope is screened by multivariable joint probability distribution,the boundary conditions were compared and merged,and finally the dynamic load conditions were obtained.In this paper,a set of dynamic load condition design method based on the aircraft requirements is constructed,which systematically covers all kinds of situations that occur in the process of aircraft landing,and improves the conventional design process of aircraft dynamic load.

UAV-mounted Ground Penetrating Radar: an example for the stability analysis of a mountain rock debris slope

This paper describes scientific research conducted to highlight the potential of an integrated GPR-UAV system in engineering-geological applications.The analysis focused on the stability of a natural scree slope in the Germanasca Valley,in the western Italian Alps.As a consequence of its steep shape and the related geological hazard,the study used different remote sensed methodologies such as UAV photogrammetry and geophysics survey by a GPR-drone integrated system.Furthermore,conventional in-situ surveys led to the collection of geological and geomorphological data.The use of the UAV-mounted GPR allowed us to investigate the bedrock depth under the detrital slope deposit,using a non-invasive technique able to conduct surveys on inaccessible areas prone to hazardous conditions for operators.The collected evidence and the results of the analysis highlighted the stability of the slope with Factors of Safety,verified in static conditions(i.e.,natural static condition and static condition with snow cover),slightly above the stability limit value of 1.On the contrary,the dynamic loading conditions(i.e.,seismic action applied)showed a Factor of Safety below the stability limit value.The UAV-mounted GPR represented an essential contribution to the surveys allowing the definition of the interface debris deposit-bedrock,which are useful to design the slope model and to evaluate the scree slope stability in different conditions.

Experimental Investigations on Web Crippling Failure Modes of Aluminum Hollow and Composite Tubes

In order to study the web-crippling behavior of aluminum hollow sectionsubjected to concentrated load, sixteen aluminum hollow tubes with different loadingconditions, bearing length and web slenderness ratios were tested. This paper alsodiscussed a method to improve the web crippling strength of the aluminum hollowsections by infilling the mortar as composite section, and four aluminum compositesections were tested. The literature has reported lots of web crippling tests, but there isfew reports on web crippling behavior of aluminum composite sections. Interior-Ground(IG) and End-Ground (EG) loading conditions were adopted, with the specimens placedon the ground to simulate the load of floor joists. Specimens were also placed on abearing plate with end (ETF) or interior (ITF) bearing load. The influence of supportingconditions, loading positions, bearing length and web slenderness ratios on web cripplingultimate bearing capacity and ductility of aluminum hollow sections was studied. Theenhancements of infilling mortar were also evaluated. The results obtained from theexperiments show that infilling the mortar in aluminum hollow tubes is an effectivemethod for enhancing the ultimate capacity of the web, especially for specimens underInterior-Ground (IG) condition. Based on the results of parameter research, this paperproposes a series of design formulas for well predicting web crippling ultimate capacityof aluminum hollow and composite tubes under four different loading and boundaryconditions.

Numerical analysis of stress distribution in the upper arm tissues under an inflatable cuff：Implications for noninvasive blood pressure measurement

An inflatable cuff wrapped around the upper arm is widely used in noninvasive blood pressure measurement.However, the mechanical interaction between cuff and arm tissues, a factor that potentially affects the accuracy of noninvasive blood pressure measurement, remains rarely addressed. In the present study, finite element（FE） models were constructed to quantify intra-arm stresses generated by cuff compression, aiming to provide some theoretical evidence for identifying factors of importance for blood pressure measurement or explaining clinical observations. Obtained results showed that the simulated tissue stresses were highly sensitive to the distribution of cuff pressure on the arm surface and the contact condition between muscle and bone. In contrast, the magnitude of cuff pressure and small variations in elastic properties of arm soft tissues had little influence on the efficiency of pressure transmission in arm tissues. In particular, it was found that a thickened subcutaneous fat layer in obese subjects significantly reduced the effective pressure transmitted to the brachial artery, which may explain why blood pressure overestimation occurs more frequently in obese subjects in noninvasive blood pressure measurement.

DEVELOPMENT OF CALCULATING MODEL APPLICABLE FOR CYLINDER WALL DYNAMIC HEAT TRANSFER

In the calculation of submarine air conditioning load of the early stage, the obtained heat is regarded as cooling load. The confusion of the two words causing the cooling load figured out is abnormally high, and the change of air conditioning cooling load can not be indicated. In accordance with submarine structure and heat transfer characteristics of its inner components, Laplace transformation to heat conduction differential equation of cylinder wall is carried out. The dynamic calculation of submarine conditioning load based on this model is also conducted, and the results of calculation are compared with those of static cooling load calculation. It is concluded that the dynamic cooling load calculation methods can illustrate the change of submarine air conditioning cooling load more accurate than the static one.

Comparative Study of the Thermal Comfort of Four Materials Type Used in the Construction of a Building

This research work consisted in making a comparative study of the thermal comfort of four materials types used in the construction of a building.A simulation of the building with the various materials on the KoZiBu software in reference and optimized situation was carried out.A study on the sensitive and air-conditioning loads as well as the curves of temperatures on a building of type F2 in situation of reference and in optimized situation was made on the one hand and the other hand a study on the same building without air-conditioning in reference and optimized situation.Finally,the analysis of the results favorizes the choice of the material having the best thermal comfort.The conclusions of these works show that the material that can give the best comfort and the most economics in terms of energy is the adobe which offers temperatures(301.40K or 28.40°C)and a good indoor thermal environment compared to BLT(blocks of cut laterite),BTC(blocks of compressed earth)and cinder block.Dwellings built with earthen materials offer a better indoor thermal environment than those built with modern construction materials,which are used more and more in the construction of houses in Burkina Faso.

Describing failure in geomaterials using second-order work approach

Geomaterials are known to be non-associated materials. Granular soils therefore exhibit a variety of failure modes, with diffuse or localized kinematical patterns. In fact, the notion of failure itself can be confusing with regard to granular soils, because it is not associated with an obvious phenomenology. In this study, we built a proper framework, using the second-order work theory, to describe some failure modes in geomaterials based on energy conservation. The occurrence of failure is defined by an abrupt increase in kinetic energy. The increase in kinetic energy from an equilibrium state, under incremental loading, is shown to be equal to the difference between the external second-order work,involving the external loading parameters, and the internal second-order work, involving the constitutive properties of the material. When a stress limit state is reached, a certain stress component passes through a maximum value and then may decrease. Under such a condition, if a certain additional external loading is applied, the system fails, sharply increasing the strain rate. The internal stress is no longer able to balance the external stress, leading to a dynamic response of the specimen. As an illustration, the theoretical framework was applied to the well-known undrained triaxial test for loose soils. The influence of the loading control mode was clearly highlighted. It is shown that the plastic limit theory appears to be a particular case of this more general second-order work theory. When the plastic limit condition is met, the internal second-order work is nil. A class of incremental external loadings causes the kinetic energy to increase dramatically, leading to the sudden collapse of the specimen, as observed in laboratory.

Control Strategies of Large-scale Residential Air Conditioning Loads Participating in Demand Response Programs

Residential air conditioning(RAC)loads have great potential to be included in demand response(DR)programs.This paper studies large-scale RAC loads participating in DR programs,such as modeling,parameters identification,DR characteristics and control strategies.First,an aggregate model of large-scale RAC loads are established based on the buildings’performance with heat storage and insulation,avoiding the calculation of a single RAC model.Then,parameters of the aggregate model are identified based on the RACs’power and outdoor temperatures.Based on the aggregate model,DR characteristics of RAC loads are analyzed,including the dynamic relationship between power,outdoor and indoor temperature,and the potential of DR combined with the users’comfort.Next,the DR control strategies adapted for large-scale RAC loads are established by adjusting the temperature set-points.The DR strategies consider users’comfort and calculate the control signals of each RAC load according to the DR power,including adjustment temperature and adjustment time,which are sent to each RAC load for execution.In the DR process,the control center does not need to obtain the users’indoor temperature,which is conducive to protecting the users’privacy.DR strategies of RAC loads when the control degree within/beyond the DR potential are both proposed,and a load recovery control strategy is also introduced.Finally,the effectiveness and accuracy of the proposed model and DR control strategies are verified by simulation results.

Hybrid Control Strategy for Air-conditioning Loads Participating in Peak Load Reduction Through Wide-range Transport Model

This paper proposes a hybrid control strategy of air-conditioning loads(ACLs)for participating in peak load reduction.The hybrid control strategy combines the temperature setpoint adjustment(TSA)control and on/off control together to make full use of response potentials of ACLs.The primary free transport model of ACLs has been established in literature at or near a fixed temperature setpoint.In this paper,a wide-range transport(WRT)model suitable for larger value of TSA is proposed.The WRT model can be constructed easily through the parameter of devices and indoor and outdoor temperature.To modulate the aggregate response characteristics of ACLs more friendly to the power grid,the safe protocol(SP)is adopted and integrated into the WRT model,which achieves a good unification of oscillation suppression and efficient modeling.Moreover,the hybrid control strategy is implemented based on the WRT model,and the model predictive control(MPC)controller is designed considering the tracking error and control switch cost.At last,the superiority of the hybrid control strategy is verified and the performance of ACLs for peak load reduction under this controller is simulated.The simulation results show that the hybrid control strategy could exploit the load reduction potential of ACLs fully than the TSA mode and track the reference signal more accurately.

Relationship between the real contact behavior and tribological characteristics of cotton fabric

The tribological characteristics of cotton fibers play an important role in engineering and materials science,and real contact behavior is a significant aspect in the friction behavior of cotton fibers.In this study,the tribological characteristics of cotton fibers and their relationship with the real contact behavior are investigated through reciprocating linear tribotesting and real contact analysis.Results show that the friction coefficient decreases with a general increase in load or velocity,and the load and velocity exhibit a co‐influence on the friction coefficient.The dynamic change in the real contact area is recorded clearly during the experiments and corresponds to the fluctuations observed in the friction coefficient.Moreover,the friction coefficient is positively correlated with the real contact area based on a quantitative analysis of the evolution of friction behavior and the real contact area at different loads and velocities.This correlation is evident at low velocities and medium load.