A NEW MODEL FOR CALCULATING PROPAGATION PRESSURE AND INITIATION PRESSURE OF PIPELINES WITH A LOCAL DENT

An analytical model of a ring with six yield hinges and two deformable arc segments is presented for. the prediction of the buckle propagation pressure and initiation pressure in offshore pipelines. The configuration of a fully collapsed ring is considered as a real dumbbell shape with a line touch between two 'bells', instead of the dumbbell shape with a point touch of two diametrically opposite points. Calculations are performed assuming that the dominant effect on the plastic energy dissipation has the circumferential bending mode. For the linear strain-hardening materials it is found that theoretical predictions based on the above model for both propagation pressure and initiation nressure are in good agreement with experimental results of Kyriakides et al.

Study on Crack Propagation Parameters of Tunnel Lining Structure Based on Peridynamics

The numerical simulation results utilizing the Peridynamics(PD)method reveal that the initial crack and crack propagation of the tunnel concrete lining structure agree with the experimental data compared to the Japanese prototype lining test.The load structure model takes into account the cracking process and distribution of the lining segment under the influence of local bias pressure and lining thickness.In addition,the influence of preset cracks and lining section formon the crack propagation of the concrete lining model is studied.This study evaluates the stability and sustainability of tunnel structure by the Peridynamics method,which provides a reference for the analysis of the causes of lining cracks,and also lays a foundation for the prevention,reinforcement and repair of tunnel lining cracks.

A Spiral History of the Development of Ways to Identify the Correct Position of the Injection Needle in Relation to the Peripheral Nerve: A Brief Historical Essay

The first way to identify the needle in relation to the peripheral nerve W. Halsted and R. Hall in 1884 performed the first regional blockade (using direct visualization). However, Vassily von Anrep was a few months earlier described the blockade of the peripheral nerve by anatomical landmarks. In 1912, the blockade of the brachial plexus was first performed using electrical stimulation, but this technique has been widely used only since 1962. The most popular way to identify the needle relative to the nerve at the moment remains US guidance. A promising direction may be optical coherence tomography. But this method is under development. In the last decade, a method for determining the pressure of a local anesthetic has been introduced into practice to determine the position of the needle relative to the nerve.

Microstructure and properties of 35 kg large aluminum alloy flywheel housing components formed by squeeze casting with local pressure compensation

The squeeze casting method with local pressure compensation was proposed to form a flywheel housing component with a weight of 35 kg.The numerical simulation,microstructure observation and phase characterization were performed,and the influence of local pressure compensation on feeding of thick-wall position,microstructure and mechanical properties of the formed components were discussed.Results show that the molten metal keeps a good fluidity and the filling is complete during the filling process.Although the solidification at thick-wall positions of the mounting ports is slow,the local pressure compensation effectively realizes the local forced feeding,significantly eliminating the shrinkage cavity defects.In the microstructure of AlSi9Mg alloy,α-Al primarily consists of fragmented dendrites and rosette grains,while eutectic Si predominantly comprises needles and short rods.The impact of local pressure compensation on strength is relatively minimal,yet its influence on elongation is considerable.Following local pressure compensation,the average elongation at the compensated areas is 9.18%,which represents a 44.90%higher than that before compensation.The average tensile strength is 209.1 MPa,and the average yield strength is 100.6 MPa.The local pressure compensation can significantly reduce or even eliminate the internal defects in the 35 kg large-weight components formed by squeeze casting.

Unified analysis for stabilized methods of low-order mixed finite elements for stationary Navier-Stokes equations

A unified analysis is presented for the stabilized methods including the pres- sure projection method and the pressure gradient local projection method of conforming and nonconforming low-order mixed finite elements for the stationary Navier-Stokes equa- tions. The existence and uniqueness of the solution and the optimal error estimates are proved.

Effects of corner modifications on wind loads and local pressures on walls of tall buildings

In this study, the aerodynamic characteristics of tall buildings with corner modifications (e.g., local wind force coefficients, mean pressure distributions, normalized power spectrum density, and extreme local pressure) were examined. Wind tunnel experiments were conducted to measure the wind pressures on building models with different heights and recessed corners of different ratios. At a wind direction of a = 0° (i.e., wind blowing on the front of a building), corner modifications effectively reduced wind forces in all cases. Specifically, small corner modification ratios reduced wind forces more effectively than their larger counterparts. However, corner modifications resulted in extreme local pressure on building surfaces. In addition, for small corner modification ratios, the probability of extreme local pressure occurring at a = 0° was high. This probability was also high for large corner modification ratios at a = 15° (i.e., wind blowing slightly obliquely on the front of a building) because wind blowing obliquely creates substantial vortex shedding on one side surface and extreme negative pressure over one building side surface. Results of computational fluid dynamic modeling were adopted to determine details of the aerodynamic characteristics of tall buildings with corner modifications.

Local Unstable Entropy and Local Unstable Pressure for Partially Hyperbolic Endomorphisms

In this paper,local unstable metric entropy,local unstable topological entropy and local unstable pressure for partially hyperbolic endomorphisms are introduced and investigated.Specially,two variational principles concerning relationships among the above mentioned numbers are formulated.

On the Pressure Drop and the Velocity Distribution in the Cylindrical Vortex Chamber with Two Inlet Pipes for the Control of Vortex Flow

Vortex flow is applied to a cyclone dust collector, a vortex combustion chamber, and a vortex diode for vortex control. In order to apply the vortex flow to the industries, it is necessary to keep the stable flow condition and to estimate the response time of the transient flow process and also the intensity of the vortex flow. For control vortex flow, two types of vortex chamber with two inlet pipes were designed. One of them is to promote the vortex flow named as Co-Rotating Flow System and another one is to hinder the vortex flow named as Counter-Rotating Flow System. The pressure drops and the velocity distributions were measured for these vortex chambers. The estimation of the tangential velocity by the application of the angular momentum flux is compared with the measured velocity by a cylindrical Pitot-tube. The characteristics of the total pressure drop could be explained by introducing the circulation.