A phenomenological model for plastic flow behavior of rotating band material with a large temperature range

The plastic flow behavior of the rotating band material is investigated in this paper. The rotating band material is processed from H96 brass alloy, which is hardened to a much higher yield strength compared to the annealed one. The dynamically uniaxial compression behavior of the material is tested using the split Hopkinson pressure bar(SHPB) with temperature and strain rate ranging from 297 to 1073 K and500 to 3000 s^(-1), respectively, and a phenomenological plastic flow stress model is developed to describe the mechanical behavior of the material. The material is found to present noticeable temperature sensitivity and weak strain-rate sensitivity. The construction of the plastic flow stress model has two steps. Firstly, three univariate stress functions, taking plastic strain, plastic strain rate and temperature as independent variable, respectively, are proposed by fixing the other two variables. Then, as the three univariate functions describe the special cases of flow stress behavior under various conditions, the principle of stress compatibility is adopted to obtain the complete flow stress function. The numerical results show that the proposed plastic flow stress model is more suitable for the rotating band material than the existing well-known models.

A transient production prediction method for tight condensate gas wells with multiphase flow

Considering the phase behaviors in condensate gas reservoirs and the oil-gas two-phase linear flow and boundary-dominated flow in the reservoir,a method for predicting the relationship between oil saturation and pressure in the full-path of tight condensate gas well is proposed,and a model for predicting the transient production from tight condensate gas wells with multiphase flow is established.The research indicates that the relationship curve between condensate oil saturation and pressure is crucial for calculating the pseudo-pressure.In the early stage of production or in areas far from the wellbore with high reservoir pressure,the condensate oil saturation can be calculated using early-stage production dynamic data through material balance models.In the late stage of production or in areas close to the wellbore with low reservoir pressure,the condensate oil saturation can be calculated using the data of constant composition expansion test.In the middle stages of production or when reservoir pressure is at an intermediate level,the data obtained from the previous two stages can be interpolated to form a complete full-path relationship curve between oil saturation and pressure.Through simulation and field application,the new method is verified to be reliable and practical.It can be applied for prediction of middle-stage and late-stage production of tight condensate gas wells and assessment of single-well recoverable reserves.

The Application of Thermomechanical Dynamics (TMD) to the Analysis of Nonequilibrium Irreversible Motion and a Low-Temperature Stirling Engine

We applied the method of Thermomechanical Dynamics (TMD) to a low-temperature Stirling engine, and the dissipative equation of motion and time-evolving physical quantities are self-consistently calculated for the first time in this field. The thermomechanical states of the heat engine are in Nonequilibrium Irreversible States (NISs), and time-dependent thermodynamic work W(t), internal energy E(t), energy dissipation or entropy Qd(t), and temperature T(t), are precisely studied and computed in TMD. We also introduced the new formalism, Q(t)-picture of thermodynamic heat-energy flows, for consistent analyses of NISs. Thermal flows in a long-time uniform heat flow and in a short-time heat flow are numerically studied as examples. In addition to the analysis of time-dependent physical quantities, the TMD analysis suggests that the concept of force and acceleration in Newtonian mechanics should be modified. The acceleration is defined as a continuously differentiable function of Class C2 in Newtonian mechanics, but the thermomechanical dynamics demands piecewise continuity for acceleration and thermal force, required from physical reasons caused by frictional variations and thermal fluctuations. The acceleration has no direct physical meaning associated with force in TMD. The physical implications are fundamental for the concept of the macroscopic phenomena in NISs composed of systems in thermal and mechanical motion.

Hydrate agglomeration modeling and pipeline hydrate slurry flow behavior simulation

Dynamic modeling and numerical simulation of hydrate slurry flow behavior are of great importance to offshore hydrate management.For this purpose, a dynamic model of hydrate agglomeration was proposed in this paper.Based on population balance equation, the frame of the dynamic model was established first, which took both hydrate agglomeration and hydrate breakage into consideration.Then, the calculating methods of four key parameters involved in the dynamic model were given according to hydrate agglomeration dynamics.The four key parameters are collision frequency, agglomeration efficiency, breakage frequency and the size distribution of sub particles resulting from particle breakage.After the whole dynamic model was built, it was combined with several traditional solid–liquid flow models and then together solved by the CFD software FLUENT 14.5.Finally, using this method, the influences of flow rate and hydrate volume fraction on hydrate particle size distribution, hydrate volume concentration distribution and pipeline pressure drop were simulated and analyzed.

Unsteady Flow and Structural Behaviors of Centrifugal Pump under Cavitation Conditions

Cavitation has a significant e ect on the flow fields and structural behaviors of a centrifugal pump. In this study, the unsteady flow and structural behaviors of a centrifugal pump are investigated numerically under di erent cavitation conditions. A strong two-way coupling fluid-structure interaction simulation is applied to obtain interior views of the e ects of cavitating bubbles on the flow and structural dynamics of a pump. The renormalization-group k-ε turbulence model and the Zwart–Gerbe–Belamri cavitation model are solved for the fluid side, while a transient structural dynamic analysis is employed for the structure side. The di erent cavitation states are mapped in the head-net positive suction head(H-NPSH) curves and flow field features inside the impeller are fully revealed. Results indicate that cavitating bubbles grow and expand rapidly with decreasing NPSH. In addition, the pressure fluctuations, both in the impeller and volute, are quantitatively analyzed and associated with the cavitation states. It is shown that influence of the cavitation on the flow field is critical, specifically in the super-cavitation state. The e ect of cavitation on the unsteady radial force and blade loads is also discussed. The results indicate that the averaged radial force increased from 8.5 N to 54.4 N in the transition progress from an onset cavitation state to a super-cavitation state. Furthermore, the structural behaviors, including blade deformation, stress, and natural frequencies, corresponding to the cavitation states are discussed. A large volume of cavitating bubbles weakens the fluid forces on the blade and decreases the natural frequencies of the rotor system. This study could enhance the understanding of the e ects of cavitation on pump flow and structural behaviors.

Visualization of flow behavior in ore-segregated packed beds with fine interlayers

Ore particles,especially fine interlayers,commonly segregate in heap stacking,leading to undesirable flow paths and changeable flow velocity fields of packed beds.Computed tomography(CT),COMSOL Multiphysics,and MATLAB were utilized to quantify pore structures and visualize flow behavior inside packed beds with segregated fine interlayers.The formation of fine interlayers was accompanied with the segregation of particles in packed beds.Fine particles reached the upper position of the packed beds during stacking.CT revealed that the average porosity of fine interlayers(24.21%)was significantly lower than that of the heap packed by coarse ores(37.42%),which directly affected the formation of flow paths.Specifically,the potential flow paths in the internal regions of fine interlayers were undeveloped.Fluid flowed and bypassed the fine interlayers and along the sides of the packed beds.Flow velocity also indicated that the flow paths easily gathered in the pore throat where flow velocity(1.8×10^-5 m/s)suddenly increased.Fluid stagnant regions with a flow velocity lower than 0.2×10^-5 m/s appeared in flow paths with a large diameter.

A visualized study of interfacial behavior of air–water two-phase flow in a rectangular Venturi channel

A visualized investigation was carried out on the effect of the diverging angle on the bubble motion and interfacial behavior in a Venturi-type bubble generator.It was found two or three large vortexes formed in the diverging section,resulting in strong reentrant jet flow in the front of the bubbles or slugs rushing out of the throat.The jet flow in return bumps into the ongoing bubbles or slugs,leading to strong interaction between the gas and liquid phases.The diverging angle has significant influence on the reentrant flow process and the performance of the bubble generator as well.Increasing the diverging angle results in the reentrant flow moving further forward to the upstream and intensifies the interaction between the two phases.As a consequence,the breakup or collapse of bubbles becomes more violent,whereby finer bubbles are generated.As such,the reentrant flow strongly links to the performance of the Venturi channel taken as a bubble generator,and that a moderate increase in the diverging angle can improve its performance without additional increase in flow resistance like that by increasing liquid flow rate.

Numerical investigation of dynamical behavior of tethered rigid spheres in supersonic flow

The dynamical behavior of two tethered rigid spheres in a supersonic flow is numerically investigated. The tethered lengths and radius ratios of the two spheres are different. The two spheres, which are centroid axially aligned initially, are held stationary first, then released, and subsequently let fly freely in a supersonic flow. The mean qualities of the system and the qualities of the bigger sphere are considered and compared with the situations without the tether. In the separation process, six types of motion caused by the spheres, tether, and fluid interaction are found. The results show that the mean x-velocity of the system changes in a different manner for different radius ratios, and the x-velocity of the bigger sphere is uniformly reduced but through different mechanisms.

Effects of pin geometry on the material flow behavior of friction stir spot welded 2A12 aluminum alloy

A three-dimensional finite volume model was established by the ANSYS FLUENT software to simulate the material flow behavior during the friction stir spot welding （FSSW） process. Effects of the full-threaded pin and the reverse-threaded pin on the material flow behavior were mainly discussed. Results showed that the biggest material flow velocity appeared at the outer edge of the tool shoulder. The velocity value became smaller with the increase of the distance away from the tool surface. In general, material flows downwards along the pin thread when the full-threaded pin is used. Meanwhile, both the materials of the upper and the lower plates flow towards the lap interface along the pin thread when the reverse-threaded pin is used. The numerical simulation results were investigated by experiment, in which 2A12 aluminum alloy was used as the research object. The effective sheet thickness （EST） and stir zone （SZ） width of the joint by the reverse-threaded pin were much bigger than those by the full-threaded pin. Accordingly, cross tension failure load of the joint by the reverse-threaded pin is 23% bigger than the joint by the full-threaded pin.

Effects of casting process on microstructures and flow stress behavior of Mg-9Gd-3Y-1.5Zn-0.8Zr semi-continuous casting billets

Mg-9Gd-3Y-1.5Zn-0.8Zr alloys own high strength,good heat and corrosion resistance.However,it is difficult for the fabrication of large-scale billets,due to the poor deformation ability and strong hot-crack tendency.This work investigated the casting process on the microstructures and flow stress behaviors of the semi-continuous casting billets for the fabrication of large-scale Mg-9Gd-3Y-1.5Zn-0.8Zr billets.The casting process(electromagnetic intensity and casting speed)shows outstanding effects on the microstructures and flow stress behavior of the billets.The billets with the specific casting process(I=68 A,V=65 mm/min)exhibit uniform microstructures and good deformation uniformity.

Flow Stress Behavior and Processing Map of Al-Cu-Mg-Ag Alloy during Hot Compression

The hot deformation behavior of Al-Cu-Mg-Ag was studied by isothermal hot compression tests in the temperature range of 573-773 K and strain rate range of 0.001-1 s^-1 on a Gleeble 1500 D thermal mechanical simulator. The results show the flow stress of Al-Cu-Mg-Ag alloy increases with strain rate and decreases after a peak value, indicating dynamic recovery and recrystallization. A hyperbolic sine relationship is found to correlate well the flow stress with the strain rate and temperature, the flow stress equation is estimated to illustrate the relation of strain rate and stress and temperature during high temperature deformation process. The processing maps exhibit two domains as optimum fields for hot deformation at different strains, including the high strain rate domain in 623-773 K and the low strain rate domain in 573-673 K.

Electrical properties of MOCVD-grown GaN on Si (111) substrates with low-temperature AlN interlayers

The electrical properties of the structure of GaN grown on an Si （111） substrate with low-temperature （LT） A1N interlayers by metal-organic chemical-vapour deposition are investigated. An abnormal P-type conduction is observed in our GaN-on-Si structure by Hall effect measurement, which is mainly due to the A1 atom diffusing into the Si substrate and acting as an acceptor dopant. Meanwhile, a constant n-type conduction channel is observed in LT-A1N, which causes a conduction-type conversion at low temperature （50 K） and may further influence the electrical behavior of this structure.

Study on Local Optical Flow Method Based on YOLOv3 in Human Behavior Recognition

In the process of human behavior recognition, the traditional dense optical flow method has too many pixels and too much overhead, which limits the running speed. This paper proposed a method combing YOLOv3 (You Only Look Once v3) and local optical flow method. Based on the dense optical flow method, the optical flow modulus of the area where the human target is detected is calculated to reduce the amount of computation and save the cost in terms of time. And then, a threshold value is set to complete the human behavior identification. Through design algorithm, experimental verification and other steps, the walking, running and falling state of human body in real life indoor sports video was identified. Experimental results show that this algorithm is more advantageous for jogging behavior recognition.

The flow behavior in as-extruded AZ31 magnesium alloy under impact loading

As-extruded AZ31 magnesium alloy samples were compressed at ambient temperature and strain rates of 1000-3000 s^(−1).The fracture surfaces of cracked samples,the evolution of microstructures and macrotextures were detected.The received flow curves exhibit an abnormal behavior at strain rates above 1500 s^(−1).A strain constitutive model based on strain equivalent principle was applied to analyze the flow curves of the damaged samples.The results indicate that the abnormal flow behaviors of the fractured samples are related to the increasing area of crack surfaces,and kinetic energy during dynamic crack nucleation and propagation.The initiation of the micro-crack also causes obvious flow softening in the cracked samples.The shapes of flow stresses of the intact samples are affected by twinning.©2018 Published by Elsevier B.V.on behalf of Chongqing University.

A Study on Flow Structure around a Bridge Beam and Behavior of Sea Water Mist

Okinawa in the subtropical islands enclosed in the ocean has a problem that corrosion of structures progresses quickly because of high temperature, high humidity and adhesion of sea-water mists flying from sea. Author is interested in corrosion of bridge made of weatherability steel. Therefore, it needs to investigate the flow structure around bridge beams and behavior of sea-water mist (droplet). In this paper, flow visualization and PIV are attempted to understand the flow structures around bridge beams and, furthermore, numerical approach of motion of droplets is attempted to understand the collision of sea-water mists on the bridge wall.

Large Time Behavior of a Weak Solution for Non-Newtonian Flow

This paper concerns large time behavior of a regular weak solution for non-Newtonian flow equations. It is shown that the decay of the solution is of exponential type when the force term is equal to zero and the domain is bounded. Moreover, the ratio of the enstrophy over the energy has a limit as time tends to infinity, which is an eigenvaiue of the Stokes operator.

Abnormal Crowd Behavior Detection Based on the Entropy of Optical Flow

To improve the detection accuracy and robustness of crowd anomaly detection,especially crowd emergency evacuation detection,the abnormal crowd behavior detection method is proposed.This method is based on the improved statistical global optical flow entropy which can better describe the degree of chaos of crowd.First,the optical flow field is extracted from the video sequences and a 2D optical flow histogram is gained.Then,the improved optical flow entropy,combining information theory with statistical physics is calculated from 2D optical flow histograms.Finally,the anomaly can be detected according to the abnormality judgment formula.The experimental results show that the detection accuracy achieved over 95%in three public video datasets,which indicates that the proposed algorithm outperforms other state-of-the-art algorithms.

The Effect of Sparger Geometry on Gas Bubble Flow Behaviors Using Electrical Resistance Tomography

By electrical resistance tomography (ERT) the cross sectional profiles of gas hold-up in a φ56mm bubble column are obtained with four designs of gas sparger. The effect of sparger geometry on the bubble distribution is re-vealed by applying a sensitivity conjugated gradients reconstruction method (SCG). Experimental results show that over-all hold-up obtained by ERT is generally in good agreement with those measured with the pressure transducer and the ERT system produces informative evidence that the radial profiles of hold-up is very similar to the sparger design in the lower section of bubble column. Meanwhile, the rise velocity of bubble swarm and the Sauter mean bubble size are evaluated using ERT based on dynamic gas disengagement theory. The experimental results are in good agreement with correlations and conventional estimation obtained using pressure transmitter methods.

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We used therefore start-up experiments with constant shear rates and can speak consequently of shear stress instead of viscosity.The shear stress increases sharply at the beginning of the stress growth experiment,passes an overshoot and begins to decrease up to the steady state shear stress.We can assume that a stress growth curve with an overshoot points out to thixotropic behavior.After the steady state shear stress is reached,the shear deformation is stopped,and the stress relaxation begins.It is to be expected that the shear stress will recover after the stress relaxation.Systems with shear thinning and plastic flow behavior were examined.The thixotropy is discussed in relation to the flow behavior.Stress growth experiments were performed with shear rates from the first Newtonian region and from the shear thinning region of the systems with shear thinning flow behavior.Stress start-up experiments were carrying out with shear rates from the first and second yield stress regions and from the transition section of a system with plastic flow behavior.

基于改进FlowNet 2.0光流算法的奶牛反刍行为分析方法

反刍行为与奶牛生产、繁殖性能及疾病等因素密切相关,针对非接触式奶牛反刍行为分析受牛只自身运动或背景干扰等不足,提出改进FlowNet 2.0光流算法,首先计算垂直光流分量替代光流速度构建光流图,消除水平运动对光流分析干扰;其次设置光流阈值避免垂直光流中头部运动光流干扰;同步计算反刍区域面积阈值提取区域内光流数据,避免目标对象头部运动对反刍光流的影响;最后滤波拟合计算反刍曲线,确定曲线周期,增大波峰波谷差值,提升奶牛反刍咀嚼频次计数的准确性。以不同场景下20头奶牛的30段反刍行为视频为数据集,验证本文方法的有效性、鲁棒性与准确性,试验结果表明,改进FlowNet 2.0光流算法计算奶牛反刍咀嚼频次准确率为99.39%,相较于FlowNet 2.0光流算法准确率提升5.75个百分点。