Physical-Rheological Properties and Performances of Rejuvenated(Styrene-Butadiene-Styrene)Asphalt with Polymerized-MDI and Aromatic Oil

Traditional asphalt rejuvenators,like aromatic oil(AO),are known to be effective in improving the low-temperature properties and fatigue performances of aged SBS(styrene-butadiene-styrene)modified asphalt(SBSMA)binders and mixtures.However,these rejuvenators inevitably compromise their high-temperature properties and deformation resistances because they dilute asphalt binder but do not fix the damaged structures of aged SBS.In this study,a highly-active chemical called polymerized 4,4-diphenylmethane diisocyanate(PMDI)was used to assist the traditional AO asphalt rejuvenator.The physical and rheological characteristics of rejuvenated SBSMA binders and the moisture-induced damage and rut deformation performances of corresponding mixtures were comparatively evaluated.The results showed that the increasing proportion of AO compromises the hightemperature property and hardness of aged SBSMA binder,and an appropriate amount of PMDI works to compensate such losses;3%rejuvenator at mass ratio of AO:PMDI=70:30 can have a rejuvenated SBSMA binder with a high-temperature performance similar to that of fresh binder,approximately at 71.4°C;the use of AO can help reduce the viscosity of PMDI rejuvenated SBSMA binder for improving its workability;PMDI can help improve the resistance of AO rejuvenated SBSMA binder to deformation,especially at elevated temperatures,through its chemical reactions with aged SBS;moisture induction can enhance the resistance to damage of rejuvenated mixtures containing AO/PMDI or only PMDI;and the rejuvenator with a mass ratio of AO:PMDI=70:30 can lead the rejuvenated mixture to meet the application requirement,with a rut depth of only 2.973 mm,although more PMDI can result in a higher resistance of rejuvenated mixtures to high-temperature deformation.

The Influence of Chemical Admixtures on the Fluidity,Viscosity and Rheological Properties of Ultra-High Performance Concrete

To achieve higher strength and better durability,ultra-high performance concrete(UHPC)typically employs a relatively small water-binder ratio.However,this generally leads to an undesired increase in the paste viscosity.In this study,the effects of liquid and powder polycarboxylate superplasticizers(PCE)on UHPC are compared and critically discussed.Moreover,the following influential factors are considered:air-entraining agents(AE),slump retaining agents(SA),and defoaming agents(DF)and the resulting flow characteristics,mechanical properties,and hydration properties are evaluated assuming UHPC containing 8‰powder PCE(PCE-based UHPC).It is found that the spread diameter of powder PCE is 5%higher than that of liquid PCE.Among the chemical admixtures studied,AEs have the best effect on improving UHPC workability,while DFs have the worst effect.When the addition of AE and SA is 1.25‰and 14.7%of PCE,paste viscosity reduces by 35%and 19%,respectively compared to the paste with only 8‰PCE.A low AE dosage(1.25‰)decreases compressive strength by 4.1%,while SA(8.1%)increases UHPC compressive strength by 9.1%.Both AE and SA significantly delay the UHPC hydration process,reducing the hydration heat release peaks by 76%and 27%,respectively.

Rheological and mechanical properties of wood fiber-PP/PE blend composites

For evaluation of the rheological and mechanical properties of highly filled wood plastic composites （WPCs）, polypropylene/polyethylene （PP/PE） blends were grafted with maleic anhydride （MAH） to enhance the interfacial adhesion between wood fiber and matrix. WPCs were prepared from wood fiber up to 60 wt.% and modified PP/PE was blended by extrusion. The rheological properties were studied by using dynamic measurement. According to the strain sweep test, the linear viscoelastic region of composites in the melt was determined. The result showed that the storage modulus was independent of the strain at low strain region （〈0.1%）. The frequency sweep resuits indicated that all composites exhibited shear thinning behavior, and both the storage modulus and complex viscosity of MAH modified composites were decreased comparing to those unmodified. Flexural properties and impact strength of the prepared WPCs were measured according to the relevant standard specifications. The flexural and impact strength of the manufactured composites significantly increased and reached a maximum when MAH dosage was 1.0 wt%, whereas the flexural modulus after an initial decreased, also increased with MAH dosage. The increase in mechanical properties indicated that the presence of anhydride groups enhanced the interracial adhesion between wood fiber and PP/PE blends.

Rheological properties of warm mix asphalt binder by DSR test at medium temperature

The rheological properties including the complex modulus G＊ and the phase angle δof matrix and warm mix asphalt （WMA）binders were measured by using the dynamic shear rheometer （DSR ） test at the medium temperature ranging from 16 to 40 ℃,and the relationships between the fatigue factor G＊ sinδand the matrix binder property,WMA additive and test temperature were established.It is found that G＊ decreases with the increasing temperature while δincreases inversely,and G＊ of the asphalt binder with high WMA additive dosage is large,and δis small.G＊sinδexponentially decreases with the increasing temperature and linearly increases with the increase in additive dosage,and the amplitudes of variation are large at low temperatures and high additive dosages.The effect of WMA additive on the rheological property is more remarkable for the matrix asphalt binder with low G＊.Besides,aging has a great effect on the property of matrix asphalt binder,and a slight effect on the interaction between asphalt and additive.The high additive dosage can increase the fatigue cracking potential of the asphalt binder.

Rheological properties of low consistency TMP from thinning wood of Chinese Fir

The rheological behavior of low consistency thermomechanical pulp of Chinese fir harvested by intermediate thinning was analyzed. The results show that the apparent viscosity of pulp changed along with the beating degree, pulp consistency and shearing velocity. With the increasing of pulp consistency, the apparent viscosity of pulp increased gradually. Beating degree of pulp had an effect on microstructure of pulp. The apparent viscosity of pulp declined as beating degree of pulp increased, and the apparent viscosity of pulp fell along with the shearing velocity increasing. Based on the results, the rheological models are set up. The models showed that the fluid types of the low consistency pulp could be described as pseudoplastics fluids （non-Newtonian fluids）.

MORPHOLOGICAL MODEL FOR RHEOLOGICAL PROPERTIES OF PLANT CELL SUSPENSION CULTURE SYSTEM

This paper puts forward a physical and mathematical model for the rheological properties of a plant cell suspension culture system.The model can explain why the system is pseudoplastic satisfactorily,thus the rheological properties of the system as the effect of the flow behavior index on plant cell concentration are interpreted correctly and the mechanism of the rheological properties of the system is further understood.Therefore the model can be applied in the technological design and optimum conditions of the system and the reformation,evaluation and scale up of reactors.

Rheological Properties and Incipient Motion of Cohesive Sediment in the Haine Estuary of China

The Haihe cohesive sediment, which is typical in China, is studied systematically for its basic physical and incipient motion properties. Following the requirements of dredging works in the Haihe Estuary, cohesive sediment samples were taken from three locations. Laboratory experiments were conducted to determine the rheological properties of these samples and to examine the incipient motion of the cohesive sediment. It is found that the cohesive sediment has an obvious yield stress tau(b), which increases with the mud density in a manner of an exponential function, and so does the viscosity parameter eta. The cohesive sediment behaves like a Bingham fluid when its density is below 1.38 similar to 1.40 g/cm(3), and when denser than these values, it may become a power-law fluid. The incipient motion experiment also revealed that the incipient velocity of the cohesive sediment increases with die density in an exponential manner. Therefore, the incipient motion is primarily related to the density, which is different from the case for non-cohesive sediment in which the incipient motion is con-elated with the diameter of sand particles instead. The incipient motion occurs in two different ways depending on the concentration of mud in the bottom. For sufficiently fine particles and a concentration lower than 1.20 g/cm(3), the cohesive sediment appears as fluidized mud, and the incipient motion is in the form of instability of an internal wave. For a higher concentration, the cohesive sediment appears as general quasi-solid-mud, and the incipient motion can be described by a series of extended Shields curves each with a different porosity for newly deposited alluvial mud.

Structural Analysis and Magnetic Properties of Gd-Doped Li-Ni Ferrites Prepared Using Rheological Phase Reaction Method

A series of Gd-doped Li-Ni ferrites with the formula of LiNi0.5GdxFe2-xO4 where x = 0.00 - 0.08 in steps of 0.02, were prepared by thermolysis of oxalate precursors obtained by rheological phase reaction. The structure, morphology, and the magnetic properties of the samples were characterized by powder X-ray diffraction （XRD）, atomic force microscopy （AFM） and a vibrating sample magnetometer （VSM）. A single spinel phase was obtained in the range of x = 0.00 - 0.04. The lattice parameters of the Gd-doped samples were larger than that of pure Li-Ni ferrite, and increased in the range of 0.00 ≤ x ≤ 0.04, then decreased up to x = 0.08, because of the formation of the secondary phase （Gd- FeO3）. All samples were spheric particles with an average size of about 100 nm, but agglomerated to some extent. The hysteresis loops indicated that the saturation magnetization decreased gradually with increasing Gd content, while the variation of coercivity was related to the microstructure of the Gd-doped samples.

IMPROVEMENT OF RHEOLOGICAL AND SHAPE RETENTION PROPERTIES OF WAX-BASED MIM BINDER BY MULTI-POLYMER COMPONENTS

ＩＮＴＲＯＤＵＣＴＩＯＮＭｅｔａｌｉｎｊｅｃｔｉｏｎｍｏｌｄｉｎｇ（ＭＩＭ）ｉｓａｎｅｍｅｒｇｉｎｇｎｅｔｓｈａｐｉｎｇｐｒｏｃｅｓｗｉｔｈｔｈｅｃａｐａｂｉｌｉｔｙｏｆｐｒｏｄｕｃｉｎｇｃｏｍｐｌｅｘｍｅｔａｌｐｒｏｄｕｃｔｓｗｈｉｃｈｃａｎ?..

Rheological properties and viscosity reduction of South China Sea crude oil

The rheological properties of South China Sea （SCS） crude oil were studied. A group of synthetic long-chain polymers, including octadecyl acrylate-maleic anhydride bidodecyl amide copolymer （VR-D）, octadecyl acrylate-maleic anhydride bioctadecyl amide copolymer （VR-O） and octadecyl acrylate-maleic anhydride phenly amide copolymer （VR-A）, were employed to serve as viscosity reducers （VRs）. Their performance was evaluated by both experimental and computational methodologies. The results suggest that the SCS crude oil has low wax content yet high resin and asphaltene contents, which lead to high viscosity through formation of association structures. Additionally, the SCS crude oil appears to be a pseudoplastic fluid showing linear shear stress-shear rate dependence at low temperature. Interestingly, it gradually evolves into a Newtonian fluid with exponential relationship between shear stress and shear rate at higher temperature. Synthetic VRs demonstrate desirable and effective performance on improvement of the rheological properties of SCS crude oil. Upon the introduction of 1000ppm VR-O, which is synthesized by using octadecylamine in the aminolysis reaction, the viscosity of SCS crude oil is decreased by 44.2% at 15 ℃ and 40.2% at 40℃. The computational study suggests significant energy level increase and shear stress decrease for VR-containing crude oil systems.

Traction rheological properties of simulative soil for deep-sea sediment

The traction capacity of the mining machine is greatly in?uenced by the traction rheological properties of the deep-sea sediments. The best simulative soil was prepared for substituting the deep-sea sediment based on the deep-sea sediment collected from the Paci?c C-C mining area. Traction rheological properties of the simulative soil were studied by a home-made test apparatus. In order to accurately describe the traction rheological properties and determine traction rheological parameters, the Newtonian dashpot in Maxwell body of Burgers model was replaced by a self-similarity spring-dashpot fractance and a new rheological constitutive model was deduced by fractional derivative theory. The results show the simulative soil has obvious non-attenuate rheological properties. The transient creep and stable creep rate increase with the traction, but they decrease with ground pressure. The fractional derivative Burgers model are better in describing non-attenuate rheological properties of the simulative soil than the classical Burgers model. For the new traction rheological constitutive equation of the simulative soil, the traction rheological parameters can be obtained by ?tting the tested traction creep data with the traction creep constitutive equation. The ground contact length of track and walking velocity of the mining machine predicted by the traction rheological constitutive equation can be used to take full advantages of the maximum traction provided by the soil and safely improve mining effciency.

INVESTIGATION OF STRUCTURE AND PROPERTIES FOR POLYMER SYSTEMS BASED ON DYNAMIC RHEOLOGICAL APPROACHES

The dynamic rheological measurements have been a preferred approach to the characterization of the structure and properties for multi-component or multi-phase polymer systems,due to its sensitive response to changes of structure for these heterogeneous polymers.In the present article,recent progresses in the studies on dynamic rheology for heterogeneous polymer systems including polymeric composites filled with inorganic particles,thermo-oxidized polyolefins,phase- separated polymeric blends and functional polymers with the scaling and percolation behavior are reviewed,mainly depending on the results by the authors' group.By means of rheological measurements,not only some new fingerprints responsible for the evolution of morphology and structure concerning these polymer systems are obtained,the corresponding results are also significant for the design and preparation of novel polymer-based composites and functional materials.

Rheological and Structural Properties of Sea Cucumber Stichopus japonicus During Heat Treatment

Changes in tissue structure, rheological properties and water content of raw and heated sea cucumber meat were studied. Sea cucumber Stichopus japonicus was heated at 25℃, 70℃ and 100℃ water for 5 min. The structural changes were observed using a light microscope and the rheological parameters （rupture strength, adhesive strength and deformation） determined using a texture meter. Microscopic photograph revealed that the structural change of heated meat was greater than that of raw meat. The rupture strength, adhesive strength and deformation of raw meat were smaller than those of the heated meat. Meanwhile, rheological parameters showed positive correlation with heating temperature. These changes are mainly caused by thermal denaturation and gelatinization of collagen during heating. These changes were also evidenced in observations using a light microscope and differential scanning calorimetry.

Rheological properties of oil-based drilling fluids at high temperature and high pressure

The rheological properties of two kinds of oil-based drilling fluids with typically composition were studied at pressures up to 138 MPa and temperatures up to 204 ℃ using the RheoChan 7400 Rheometer.The experimental results show that the apparent viscosity,plastic viscosity and yield point decrease with the increase of temperature,and increase with the increase of pressure.The effect of pressure on the apparent viscosity,plastic viscosity and yield point is considerable at ambient temperature.However,this effect gradually reduces with the increase of temperature.The major factor influencing the rheological properties of oil-based drilling fluids is temperature instead of pressure in the deep sections of oil wells.On the basis of numerous experiments,the model for predict the apparent viscosity,plastic viscosity and yield point of oil-based drilling fluids at high temperature and pressure was established using the method of regressive analysis.It is confirmed that the calculated data are in good agreement with the measured data,and the correlation coefficients are more than 0.98.The model is convenient for use and suitable for the application in drilling operations.

Variation and trends in dough rheological properties and flour quality in 330 Chinese wheat varieties

The objective of this study was to investigate variation and trends in dough rheological properties and flour quality traits in 330 Chinese wheat varieties. The dough rheological properties of development time(DT), stability time(ST), and farinograph quality number(FQN)were evaluated, as well as the flour quality traits of protein(PC), wet gluten content(WGC), and sedimentation value(SV). The coefficients of variation of DT(40.5%), ST(58.1%), and FQN(42.4%) were higher than those of PC(9.1%), WGC(10.1%), and SV(15.3%). Normal distributions were observed for the flour quality indices but not for the rheological parameters. SV was strongly correlated with the three rheological parameters and accordingly might be used as a primary indicator for dough rheological property evaluation. Our results showed that there has been marked improvement in dough rheological properties for Chinese wheat varieties released since 1986, while flour quality has remained stable.

Rheological properties of tailing paste slurry

The initial shear stress and plastic cohesion ( η ) are the most important parameters reflecting the rheological properties of the paste slurry. The rheological parameters as well as the quantitative relationship among the consumption of different fill materials were obtained through the experiment and research on these parameters. They can be used to predict the scope of the values of τ and η in production for a given ratio, which can reduce the conveying resistance of fill slurry along the pipelines and avoid the blockage of the pipelines. It is found that the rheological model of the total tailing slurry belongs to the Bingham type, which has a feature of strong internal structure and large initial shear stress. The calculation formula for the resistance loss of pipelines conforms nicely to the field test and the actual production in Jinchuan Nickel Mine.

Rheological Properties of Asphalt Modified by Supramolecular UV Resistant Material-LDHs

Dynamic rheological properties of asphalt modified by Supramolecular UV resistant material—layered double hydroxides（LDHs） was studied by means of the dynamic shear rheometer（DSR） test.Two typical base asphalts were chosen and modified by 2 different LDHs contents.DSR tests were performed on the original samples,samples after exposed to outdoor and samples after the artificial accelerated UV aging tests respectively to analyze the rheological properties.It is found that when the LDHs content is between 3wt% and 5wt% of asphalt weight,the high temperature performance and fatigue resistant property of the modified asphalt become better,the UV aging resistance properties are improved.

Influence of Carboxyl Groups on the Particle Size and Rheological Properties of Polyacrylate Latices

The PAL was synthesized with BA,MMA and some monomers containing carboxyl groups（for example,acrylic acid（AA） and methacrylic acid（MAA）） as co-monomers by semi-continuous seeded emulsion polymerization technique.The influences of alkalinization temperature,the feeding manner of AA or MAA on the particles size,rheological properties and carboxyl distribution of the latex were discussed,and the rheological mechanism was analyzed.The experimental results show that the PAL system has preferable viscosity and particle size when the alkalinization temperature is 50 ℃.Different distribution of carboxyl group in the particles and different resultant rheological properties are obtained by different feeding manner of AA or MAA into the system.The TEM images show that the particle is a smooth globe with carboxyl group concentrating on the surface and stabilized with electric double layer and nonionic adsorbed layer.The concentration of carboxyl functional group on the surface of particles can be achieved by the specific polymerization technique.The rheologyical properties are determined by accretion of particle volume and variation of the two phase volume ratio resulted from the carboxyl group spreading layer.

Experimental evaluation on high temperature rheological properties of various fiber modified asphalt binders

High temperature rheological properties of fiber modified asphalt binders and impact of the type and content on such properties were studied.Three types of fiber,including polyester(PET),polyacrylonitrile(PAN) and cellulose(CEL),a control content(0%) and four levels of fiber content(2%,4%,6% and 8% by total asphalt binder mass) were used with asphalt binders.The high temperature rheological properties,consisting of complex modulus(G*) and phase angle δ,were measured using SHRP's dynamic shear rheometer(DSR) between 46-82 ℃.Experimental results indicate that the changes of G* and tan δ of fiber modified asphalt binders with the increase of test temperature tend to slow down,and the temperature susceptibility is improved obviously compared to that of original asphalt binder.Fiber modification results in the increase of rutting parameter(G*/sin δ) at high temperatures,the decrease of temperature susceptibility,and further improved high temperature performance of asphalt binder.An excellent correlation exhibits between fiber content and high temperature performance of asphalt binder.Moreover,fiber type also has different influences on the improvement of G*/sin δ,G*/sin δ of PET and PAN fiber asphalt binders are both higher than that of CEL fiber,but G*/sin δ of CEL fiber is still higher than that of original asphalt.However,there is a critical fiber content when fibers start to interact with each other.Therefore,based on the critical fiber content and economic consideration,the optimum fiber contents for various fiber-modified asphalt binders are obtained.

Effects of temperatures and pH values on rheological properties of cemented paste backfill

In this study,different influence mechanisms associated with temperatures and pH values were investigated through cemented paste backfill(CPB)systems.CPB samples were prepared with temperatures ranging from 10 to 50℃ in 10℃ increments and pH values of 3,7,and 13.Then,the CPB mixture were subjected to rheological tests,thermogravimetric analysis(TG),derivative thermogravimetry analysis(DTG),Fourier-transform infrared spectroscopy(FT-IR),and scanning electron microscopy(SEM).Results demonstrated that the temperatures had significant effects on the rheological properties of CPB,whereas the effects of pH values were relatively unapparent.Higher temperatures(over 20℃)were prone to bring higher shear stress,yield stress,and apparent viscosity with the same pH value condition.However,an overly high temperature(50℃)cannot raise the apparent viscosity.Non-neutral conditions,for pH values of 3 and 13,could strengthen the shear stress and apparent viscosity at the same temperature.Two different yield stress curves could be discovered by uprising pH values,which also led to apparent viscosity of two various curves under the same temperatures(under 50℃).Microscopically,rheological properties of CPB were affected by temperatures and pH values which enhanced or reduced the cement hydration procedures,rates,products and space structures.