The Power Supply System for HL-2A Tokamak's Magnetic Field

The highpower pulsed power supply system for the magnetic field of the HL-2A Tokamak is described in this paper. The total output power of its eight magnetic field power supply units of nearly 250 MW. Their highest DC output voltage and current are 3510 V and 45 kA, respectively. All the units are operated in a pulsed mode. The pulse duration is 5 s, and the cyclic period is 15 min. The power supply system consists mainly of pulsed flywheel motor generators, rectifying transformers, thyristor converters, diode rectifiers and switches. The system incorporates many key technologies-supply equalization with two generators and four diode bridges, constant-angle phase triggers with a wide frequency range, current equalization, a status detector for the high current 6-phase converter, and advanced monitoring based on a programmable logic computer and engineering parameter measurement. The experimental results show that the performance of the power supply system satisfies the requirements of HL-2A experiments very well.

Application of wavelet-based active power filter in accelerator magnet power supply

Since modern accelerators demand excellent stability to magnet power supply （PS）, it is necessary to decrease harmonic currents passing magnets. Aiming at depressing the rappel current from the PS in the Beijing electron-positron collider Ⅱ, a wavelet-based active power filter （APF） is proposed in this paper. An APF is an effective device to improve the quality of currents. As a countermeasure to these harmonic currents, the APF circuit generates a harmonic current, countervailing harmonic current from PS. An active power filter based on wavelet transformation is proposed. Discrete wavelet transformation is used to analyze the harmonic components in the supply current, and an active power filter circuit works according to the analysis results. Our simulation and experiment results are given to prove the effect of the APF.

Development of dipole magnet power supply for BEPC-II energy upgrading project

Purpose In order to make BEPC-II to run at a higher energy,the Institute of High Energy Physics undertook an upgrading project.One of the important factors limiting the energy boost is the power and performance of the dipole magnet power supplies;therefore,these four magnet power supplies are developed for the BEPC-II upgrading.Methods The power supplies adopt topologies of thyristor rectifiers to realize a high-power output.In the control unit of each power supply,a digital current closed loop is adopted,and the key components in the feedback loop are thermostatically controlled.In order to improve the performances of the power supplies,analog voltage regulators are added to the inner control loops.Results These four power supplies have been tested and have already been officially used in BEPC-II,and their powers have reached the requirements of the upgrading.The test results of the current stability are described and shown in this paper,which testifies that the stabilities meet the design parameters.Conclusions A digital control is applied to each SCR rectifier control.The performances of the power supplies are improved by the combination of digital current control loops and the analog voltage control loops,which makes the performances of the dipole magnet power supplies meet the requirements of the upgrading project.

New Progress of Magnetically-coupled Resonant Wireless Power Transfer Technology

近些年,无线电能传输技术受到了越来越广泛的关注。作为一种中等距离无线电能传输技术,自从美国麻省理工学院于2007年发表其研究成果后,磁耦合谐振式无线电能传输技术就成为了研究热点问题。该文在对无线电能传输技术进行总体介绍的基础上,主要对磁耦合谐振式无线电能传输技术进行概括论述。首先分析了磁耦合谐振式无线电能传输技术的基本结构和工作原理,介绍了目前运用于分析该技术的主要理论;接着对该技术目前的传输水平和热点问题进行了分类阐释,主要分为传输特性、新材料的应用、干扰问题和实际应用,介绍了目前的研究现状;最后在当前研究热点问题的基础之上,对该技术有待研究的问题以及发展趋势进行了展望。

Research on protection system of resonant network in CSNS magnet power supplies

Purpose Chinese Spallation Neutron Source(CSNS)is one of the key projects of China,in which the main magnet power supplies adopt the structures of resonant networks(Wang et al.in Sci China Phys Mech Astron 54(Suppl 2):239-244,2011).Since each network contains a lot of components,and the working state of all the components will affect the whole accelerator,it is necessary to monitor the operation of each part in the resonant network.Methods In this protections system,a supervision to 314 switch signals and 118 analog signals is realized using a chip of field programmable gate array(FPGA).The details about the hardware and software designs are introduced in this paper.Results This protection system has been used in CSNS project,and the result proves that the RCS has been well monitored by this system.Conclusions This system is a self-developed protection system according to the engineering needs of CSNS.It can realize the real-time monitoring and protection of the working state of resonance network by processing a large number of data using FPGA.

Numerical Analysis of Magnetic-Shielding Effectiveness for Magnetic Resonant Wireless Power Transfer System

Magnetic radiation phenomena appear inevitably in the magnetic-resonance wireless power transfer （MR-WPT） system, and regarding this problem the magnetic-shielding scheme is applied to improve the electromagnetic performance in engineering. In this study, the shielding effectiveness of a two-coil MR-WPT system for different material shields is analyzed in theory using Moser＇s formula and Schelkunoff＇s formula. On this basis a candidate magnetic-shielding scheme with a double-layer structure is determined, which has better shielding effectiveness and coils coupling coefficient. Finally, some finite element simulation results validate the correctness of the theoretical analysis, and the shielding effectiveness with the double-layer shield in maximum is 30？dB larger than the one with the single-layer case.

Study on a Highly Stabilized Power Supply for Hybrid-Magnet Superconducting Outsert

The superconducting outsert of the 40 T hybrid-magnet in High Magnetic Field Laboratory （HMFL） of Chinese Academy of Sciences （CAS） requires a highly stabilized power supply. In this paper, two kinds of power supply design are briefly presented and both advantages and disadvantages are analyzed. In order to overcome the drawbacks of switching power supply, a series regulated active filter is adopted and a new design is proposed which ensures cooperative relationship between the feedback control loops of the switching converter and the series regulated active filter. Besides, unlike the traditional switching power supply, which can generate positive voltage only, this new design can also generate negative voltage which is needed in the quench protection for the superconducting magnet. In order to demonstrate the effectiveness of the methodology, a low-power prototype has been accomplished. The simulation and experiment results show that the power supply achieves high precision under the combined action of two feedback control loops. The peak-to-peak amplitude of the output ripple voltage of the prototype is 0.063%, while the peak-to-peak amplitude of the output ripple current is 120 ppm.

Effect of power parameter and induction coil on magnetic field in cold crucible during continuous melting and directional solidification

Bottomless electromagnetic cold crucible is a new apparatus for continuous melting and directional solidification;however,improving its power efficiency and optimizing the configuration are important for experiment and production.In this study,a 3-D finite element (FE) method based on experimental verification was applied to calculate the magnetic flux density (Bz).The effects of the power parameters and the induction coil on the magnetic field distribution in the cold crucible were investigated.The results show that higher current intensity and lower frequency are beneficial to the increase of Bz at both the segment midpoint and the slit location.The induction coil with racetrack section can induce greater Bz,and a larger gap between the induction coil and the shield ring increases Bz.The mechanism for this effect is also discussed.

Robust Beamforming for Secured Wireless Power Transfer in MIMO Magnetic Resonant Coupling System:A Probabilistic Approach

Wireless power transfer(WPT) to support mobile and portable devices is an emerging wireless technique.Among all kinds of approaches,magnetic resonance coupling(MRC) is an excellent one for mid-range WPT,which provides better mobility,flexibility,and convenience due to its simplicity in hardware implementation and longer transmission distances.In this paper,we consider an MRCWPT system with multiple power transmitters,one intended power receiver and multiple unintended power receivers.We investigate the probabilistic robust beamforming designs and provide efficient algorithms to achieve the local optimums under two different criteria,i.e.,total source power minimization problem and min-max unintended receiving power restriction problem.As the problems are quite typical in robust design situations,our proposed robust beamformers can be conveniently applied to other probabilistic robust design problems,thus reduce the complexity as well as improve the beamforming performance.Numerical results demonstrate that the proposed algorithms can significantly improve the performance as well as the robustness of the WPT system.

General Properties of Low-frequency Power Losses in Fe-based Nanocrystalline Soft Magnetic Alloys

The dependences of the power loss per cycle on frequency f and amplitude flux density Bm have been investigated for the three main original magnetic states in five sorts of Fe-based nanocrystalline soft magnetic alloys in the ranges of 10 Hz<=f<=1000 Hz and 0.4 T<= Bm <=1.0 T. The total loss P is decomposed into the sum of the hysteresis loss Physt, the classical eddy current loss Pel and the excess loss Pexc. Physt has been found to be proportional to Bm^2 and f. The behavior of Pexc/f vs f being equivalent to P/f vs f clearly exhibits nonlinearity in the range not more than about 120 Hz, whereas the behavior of P/f vs f roughly shows linearity in the range far above 100 Hz and not more than 1000 Hz. In the range up to 1000 Hz, Physt is dominant in the original high permeability state and the state of low residual flux density, whereas Pexc in the state of high residual flux density is dominant in the wider range above about 100 Hz. The framework of the statistical theory of power loss has been used for representing the behavior of Pexc/f vs f. It has been found that the number n of the simultaneously active 'Magnetic Objects' linearly varies as n = n0 + Hexc/H0 as a function of the dynamic field Hexc in the range below about 120 Hz, whereas n approximately follows a law of the form n = n0 + (Hexc/H0)^m with 1 < m < 2 in the range far above 100 Hz and not more than 1000 Hz. The values of the field HO in principle related to the microstructure and the domain structure have been calculated for the three states.

Association between Childhood Leukaemia and Exposure to Power-frequency Magnetic Fields in Middle Europe

Abstract Objective Higher levels of exposure to extremely low-frequency magnetic fields （ELF-MF） are associated with a slightly increased risk of childhood leukaemia. Compared with more-developed Western countries, higher exposure levels are evident in the Czech Republic, probably because of the different types of housing. In light of this, we aimed to examine the association between ELF-MF exposure and childhood leukaemia in the Czech Republic. Methods We conducted a paired case-control study. The cases （children with leukaemia） were age- sex- and permanent residence-matched to controls （children without leukaemia）. Although this limited potential bias and confounding, it also limited our number of participants. Results The matched analyses included 79 case-control pairs. No significant association between ELF-MF exposure and childhood leukaemia was observed for exposures over 0.2 μT （odds ratio [0R]=0.93, confidence interval [Cl]=0.45-1.93）, 0.3 μT （0R=0.77, Cl=0.34-1.75）, or 0.4 μT （OR=0.9, Cl=0.37-2.22）. Conclusion Despite higher levels of exposure in Middle and Eastern Europe, no indication of an association between ELF-MF exposure and childhood leukaemia was determined. This in contrast to the findings of previous studies conducted in different countries.

Pulsating magneto-dipole radiation of a quaking neutron star powered by energy of Alfvn seismic vibrations

We compute the characteristic parameters of the magneto-dipole radiation of a neutron star undergoing torsional seismic vibrations under the action of Lorentz restoring force about an axis of a dipolar magnetic field experiencing decay. After a brief outline of the general theoretical background of the model of a vibration-powered neutron star, we present numerical estimates of basic vibration and radiation characteristics, such as frequency, lifetime and luminosity, and investigate their time dependence on magnetic field decay. The presented analysis suggests that a gradual decrease in frequencies of pulsating high-energy emission detected from a handful of currently monitored AXP/SGR-like X-ray sources can be explained as being produced by the vibration-powered magneto-dipole radiation of quaking magnetars.

Design of Permanent Magnet Synchronous Generators for Wave Power Generation

In this paper, a design method for ocean wave permanent magnet synchronous generator(PMSG)is proposed with new performance criteria to obtain better output performance at the cost of less permanent magnet material. Besides, a simple equivalent analytical geometry method is put forward to calculate the sizes of permanent magnets. Based on geometric and electromagnetic models, four types of rotor structures are compared, i.e., embedded, tangential, tile surface mount and convex surface mount structures. The designs and comparisons of machine are performed with the same permanent magnet volume. Moreover, the influences of mechanical pole-arc coefficient of tile surface mount PMSG on electrical efficiency, output power, material corrosion, core loss, and torque ripple are investigated. Finite-element analysis method is applied to verify the results using Ansoft/Maxwell.

Calculation of Skin Depths and Eddy-Current Power Losses for Magnetic Position Sensors

We present a theoretic model to calculate skin depths and eddy-current power losses for a magnetic position sensor. Eddy-current, arised from the operation of an alternating-current excitation, induces secondary currents and fields between magnetic material and magnetic position sensor. In this paper, a magnetic position sensor system is simplified to be an outer-winding coil along the axial direction of a low carbon steel bar. The analytical model is derived from basic field and circuit theory considering a linear approximation for a nonlinear permeability. Thus the skin depths and eddy-current power losses from the model in eddy-current modeling techniques at various frequencies of an excited current source can be calculated. The proposed configuration is capable of predicting the skin depths and eddy-current power losses for a magnetic position sensor and has a consistence with experiments.

Analysis of High-Power Microwave Propagation in a Magnetized Plasma Filled Waveguide

Plasma filling can dramatically improve the performance of high power microwave devices. The characteristics of high-power microwave propagation along plasma filled waveguides in an axial magnetic field are analyzed in this paper, and the ponderomotive force effect of high power microwave is taken into consideration. Theoretical analysis and preliminary numerical calculations are performed. The analyses show that the ponderomotive effect would change the plasma density, distribution of microwave field intensity, and dispersion of wave propagation. The higher the microwave power, the stronger the ponderomotive effect. In different magnetic fields, the ponderomotive effect is different.

Maximum Power Point Tracking in Variable Speed Wind Turbine Based on Permanent Magnet Synchronous Generator Using Maximum Torque Sliding Mode Control Strategy

The present study was carried out in order to track the maximum power point in a variable speed turbine by minimizing electromechanical torque changes using a sliding mode control strategy. In this strategy, first, the rotor speed is set at an optimal point for different wind speeds. As a result of which, the tip speed ratio reaches an optimal point, mechanical power coefficient is maximized, and wind turbine produces its maximum power and mechanical torque. Then, the maximum mechanical torque is tracked using electromechanical torque. In this technique, tracking error integral of maximum mechanical torque, the error, and the derivative of error are used as state variables. During changes in wind speed, sliding mode control is designed to absorb the maximum energy from the wind and minimize the response time of maximum power point tracking(MPPT). In this method, the actual control input signal is formed from a second order integral operation of the original sliding mode control input signal. The result of the second order integral in this model includes control signal integrity, full chattering attenuation, and prevention from large fluctuations in the power generator output. The simulation results, calculated by using MATLAB/m-file software, have shown the effectiveness of the proposed control strategy for wind energy systems based on the permanent magnet synchronous generator(PMSG).

Three-Dimensional Study of the Effect of the Angle of Incidence of a Magnetic Field on the Electrical Power and Conversion Efficiency of a Polycrystalline Silicon Solar Cell under Multispectral Illumination

A three-dimensional approach to the effect of magnetic field incidence angle on electrical power and conversion efficiency is performed on a front-illuminated polycrystalline silicon bifacial solar cell. A solution of the continuity equation allowed us to present the equations of photocurrent density, photovoltage and electric power. The influence of the angle of incidence of the magnetic field on the photocurrent density, the photovoltage and the electric power has been studied. The curves of electrical power versus dynamic junction velocity were used to extract the values of maximum electrical power and dynamic junction velocity and to calculate those of conversion efficiency. From this study, it is found that the conversion efficiency values increase with the angle of incidence of the magnetic field.

Methods for Estimating Specific Loss Power in Magnetic Hyperthermia Revisited

Our purpose in this study was to present three methods for estimating specific loss power (SLP) in magnetic hyperthermia with use of an alternating magnetic field (AMF) and magnetic nanoparticles (MNPs) and to compare the SLP values estimated by the three methods using simulation studies under various diameters of MNPs (D), amplitudes (H0) and frequencies of AMF (f). In the first method, the SLP was calculated by solving the magnetization relaxation equation of Shliomis numerically (SLP1). In the second method, the SLP was obtained by solving Shliomis’ relaxation equation using the complex susceptibility (SLP2). The third method was based on Rosensweig’s model (SLP3). The SLP3 value changed largely depending on the magnetic field strength (H) in the Langevin parameter (§) and it became maximum (SLP3max) and minimum (SLP3min) when H was 0 and ±H0, respectively. The relative difference between SLP1 and SLP2 was the largest and increased with increasing D and H0, whereas that between SLP1 and was the smallest and was almost constant regardless of D and H0, suggesting that H in ξ should be taken as H0 in estimating the SLP using Rosensweig’s model. In conclusion, this study will be useful for optimizing the parameters of AMF in magnetic hyperthermia and for the optimal design of MNPs for magnetic hyperthermia.

A Simulation Study on the Specific Loss Power in Magnetic Hyperthermia in the Presence of a Static Magnetic Field

Our purpose in this study was to present a method for estimating the specific loss power (SLP) in magnetic hyperthermia in the presence of an external static magnetic field (SMF) and to investigate the SLP values estimated by this method under various diameters (D) of magnetic nanoparticles (MNPs) and amplitudes (H0) and frequencies (f) of an alternating magnetic field (AMF). In our method, the SLP was calculated by solving the magnetization relaxation equation of Shliomis numerically, in which the magnetic field strength at time t (H(t)) was assumed to be given by , with Hs being the strength of the SMF. We also investigated the SLP values in the case when the SMF with a field-free point (FFP) generated by two solenoid coils was used. The SLP value in the quasi steady state (SLPqss) decreased with increasing Hs. The plot of the SLPqss values against the position from the FFP became narrow as the gradient strength of the SMF (Gs) increased. Conversely, it became broad as Gs decreased. These results suggest that the temperature rise and the area of local heating in magnetic hyperthermia can be controlled by varying the Hs and Gs values, respectively. In conclusion, our method will be useful for estimating the SLP in the presence of both the AMF and SMF and for designing an effective local heating system for magnetic hyperthermia in order to reduce the risk of overheating surrounding healthy tissues.

Low Cost,Low Power Magnetic IEDs Detection Method Using Biaxial Magnetometry Digital Sensors

The magnetic improvised explosive devices （IEDs）, also commonly known as a type of a sticky bomb, is simply constructed devices yet very lethal. This paper puts forward the idea of an electronic compass that is capable of sensing the change of a magnetic field generated by a magnet and translating it into interpretable data, which could act as the base for the further studies and assist in developing a greener automated system for detecting this device. The electronic compass is specifically chosen for reducing power consumption of systems in addition to the fact that it is available at a low cost.