Magnetohydrodynamic(MHD)induction pumps are contactless pumps able to withstand harsh environments.The rate of fluid flow through the pump directly affects the efficiency and stability of the device.To explore the inf...Magnetohydrodynamic(MHD)induction pumps are contactless pumps able to withstand harsh environments.The rate of fluid flow through the pump directly affects the efficiency and stability of the device.To explore the influence of induction pump settings on the related delivery speed,in this study,a numerical model for coupled electromagnetic and flow field effects is introduced and used to simulate liquid metal lithium flow in the induction pump.The effects of current intensity,frequency,coil turns and coil winding size on the velocity of the working fluid are analyzed.It is shown that the first three parameters have a significant impact,while changes in the coil turns have a negligible influence.The maximum increase in working fluid velocity within the pump for the parameter combination investigated in this paper is approximately 618%.As the frequency is increased from 20 to 60 Hz,the maximum increase in the mean flow rate of the working fluid is approximately 241%.These research findings are intended to support the design and optimization of these devices.展开更多
The magnetic field generated in the air gap of the cage asynchronous machine and the harmonics of the magnetomotive forces creating that magnetic field,as well as the synchronous parasitic torques,radial magnetic forc...The magnetic field generated in the air gap of the cage asynchronous machine and the harmonics of the magnetomotive forces creating that magnetic field,as well as the synchronous parasitic torques,radial magnetic forces have been discussed in great detail in the literature,but always separately,for a long time.However,systematization of the phenomenon still awaits.Therefore,it is worth summarizing the completeness of the phenomena in a single study–with a new approach at the same time-in order to reveal the relationships between them.The role of rotor slot number is emphasized much more than before.New formulas derived for both synchronous torques and radial magnetic forces are used for further investigation.It will be shown that both phenomena in subject must be treated together.Formulas will be provided to take into account attenuation.Design guide will be provided to avoid dangerous rotor slot numbers.It will be shown that the generation of synchronous torques and radial magnetic forces do not depend–in this new approach-on the slot combination,but on the rotor slot number itself.展开更多
Electricity and magnetism and electromagnetic induction are phenomena that can be perceived by people. But their interpretation and theoretical study took a long time. The theoretical research on electricity began wit...Electricity and magnetism and electromagnetic induction are phenomena that can be perceived by people. But their interpretation and theoretical study took a long time. The theoretical research on electricity began with the discovery of Coulomb’s law in 1785, while the theoretical research on magnetism began with the discovery of Oersted’s Law in 1820. From the 1850s to the 1870s, Maxwell summarized a set of theoretical equations for electromagnetism based on some laws of predecessors. However, this set of equations contains a few statistical relationships and empirical concepts, so it is difficult to explain the physical nature of electromagnetic phenomena and principles. This paper explained that the macro phenomenon of electricity is the separation of unlike charges of new electrons produced by the orthogonal collision of old particles under the action of external forces. The physical nature of magnetism is the potential energy (magnetic energy) and information associated with the overall orientation of the moving electrons solidly recorded in the material. The physical principle of electromagnetic induction describes how change in electric current intensity generates change in magnetic intensity and vice versa through orthogonal interaction of ordered electrons. This theoretical interpretation does not require the concepts of traditional electromagnetic forces, electromagnetic fields, magnetic moments, and magnetic domains.展开更多
Recent experimental findings have demonstrated the occurrence of superconductivity in Bernal bilayer graphene when induced by a magnetic field.In this study,we conduct a theoretical investigation of the potential pair...Recent experimental findings have demonstrated the occurrence of superconductivity in Bernal bilayer graphene when induced by a magnetic field.In this study,we conduct a theoretical investigation of the potential pairing symmetry within this superconducting system.By developing a theoretical model,we primarily calculate the free energy of the system with p+ip-wave parallel spin pairing,p+ip-wave anti-parallel spin pairing and d+i d-wave pairing symmetry.Our results confirm that the magnetic field is indeed essential for generating the superconductivity.We discover that the p+ip-wave parallel spin pairing leads to a lower free energy for the system.The numerical calculations of the energy band structure,zero-energy spectral function and density of states for each of the three pairing symmetries under consideration show a strong consistency with the free energy results.展开更多
Geomagnetic storms are rapid disturbances of the Earth’s magnetosphere.They are related to many geophysical phenomena and have large influences on human activities.Observing and studying geomagnetic storms is thus of...Geomagnetic storms are rapid disturbances of the Earth’s magnetosphere.They are related to many geophysical phenomena and have large influences on human activities.Observing and studying geomagnetic storms is thus of great significance to both scientific research and geomagnetic hazards prevention.The Macao Science Satellite-1(MSS-1)project includes two high-precision Chinese geomagnetic satellites successfully launched on May 21,2023.The main purpose of MSS-1 is to accurately measure the Earth’s magnetic field.Here,we analyze early MSS-1 geomagnetic field measurements and report observations of two recent geomagnetic storms that occurred on March 24,2024 and May 11,2024.We also calculate the related geoelectric fields as an initial step towards a quantitative assessment of geomagnetic hazards.展开更多
The longitudinal wave term within Faraday’s law of electromagnetic induction (Faraday’s law) underwent recovery to ensure its suitability for theoretical derivation of the equation governing longitudinal electromagn...The longitudinal wave term within Faraday’s law of electromagnetic induction (Faraday’s law) underwent recovery to ensure its suitability for theoretical derivation of the equation governing longitudinal electromagnetic (LEM) waves. The revised Maxwell’s equations include the crucial parameters being the attenuation time constants of magnetic vortex potential and electric vortex potential generated by external electromagnetic field within the propagation medium. Specific expressions for them are obtained through theoretical analysis. Subsequently, a model for propagating magnetic P-wave generated by the superposition of a left-handed photo and a right-handed photon in a vacuum is formulated based on reevaluated total current law and revised Faraday’s law, covering wave equations, energy equation, as well as propagation mode involving mutual induction and conversion between scalar magnetic field and vortex electric field. Furthermore, through theoretical derivations centered around magnetic P-wave, evidence was presented regarding its ability to absorb huge free energy through the entangled interaction between zero-point vacuum energy field and the torsion field produced by the vortex electric field.展开更多
An acoustic dipole radiation model for magnetoacoustic tomography with magnetic induction (MAT-MI) is pro- posed, based on the analyses of one-dimensional tissue vibration, three-dimensional acoustic dipole radiatio...An acoustic dipole radiation model for magnetoacoustic tomography with magnetic induction (MAT-MI) is pro- posed, based on the analyses of one-dimensional tissue vibration, three-dimensional acoustic dipole radiation and acoustic waveform detection with a planar piston transducer. The collected waveforms provide information about the conductiv- ity boundaries in various vibration intensities and phases due to the acoustic dipole radiation pattern. Combined with the simplified back projection algorithm, the conductivity configuration of the measured layer in terms of shape and size can be reconstructed with obvious border stripes. The numerical simulation is performed for a two-layer cylindrical phantom model and it is also verified by the experimental results of MAT-MI for a tissue-like sample phantom. The proposed model suggests a potential application of conductivity differentiation and provides a universal basis for the further study of conductivity reconstruction for MAT-MI.展开更多
Magneto–acoustic tomography with magnetic induction(MAT-MI) is a multiphysics coupled imaging technique that is combined with electrical impedance tomography and ultrasound imaging. In order to study the influence ...Magneto–acoustic tomography with magnetic induction(MAT-MI) is a multiphysics coupled imaging technique that is combined with electrical impedance tomography and ultrasound imaging. In order to study the influence of adding magnetic nanoparticles as a contrast agent for MAT-MI on its physical process, firstly, we analyze and compare the electromagnetic and acoustical properties of MAT-MI theoretically before and after adding magnetic nanoparticles, and then construct a two-dimensional(2 D) planar model. Under the guidance of space-time separation theory, we determine the reasonable simulation conditions and solve the electromagnetic field and sound field physical processes in the two modes by using the finite element method. The magnetic flux density, sound pressure distribution, and related one-dimensional(1 D), 2 D, and three-dimensional(3 D) images are obtained. Finally, we make a qualitative and quantitative analysis based on the theoretical and simulation results. The research results show that the peak time of the time item separated from the sound source has a corresponding relationship with the peak time of the sound pressure signal. At this moment, MAMPTMI produces larger sound pressure signals, and the sound pressure distribution of the MAMPT-MI is more uniform, which facilitates the detection and completion of sound source reconstruction. The research results may lay the foundation for the MAT-MI of magnetically responsive nanoparticle in subsequent experiments and even clinical applications.展开更多
Based on the acoustic radiation theory of a dipole source, the influence of the transducer reception pattern is studied for magnetoacoustic tomography with magnetic induction(MAT-MI). Numerical studies are conducted...Based on the acoustic radiation theory of a dipole source, the influence of the transducer reception pattern is studied for magnetoacoustic tomography with magnetic induction(MAT-MI). Numerical studies are conducted to simulate acoustic pressures, waveforms, and reconstructed images with unidirectional, omnidirectional, and strong directional transducers.With the analyses of equivalent and projection sources, the influences of the model dimension and the layer effect are qualitatively analyzed to evaluate the performance of MAT-MI. Three-dimensional simulation studies show that the strong directional transducer with a large radius can reduce the influences of equivalent sources, projection sources, and the layer effect effectively, resulting in enhanced pressure and improved image contrast, which is beneficial for boundary pressure extraction in conductivity reconstruction. The reconstructed conductivity contrast images present the conductivity boundaries as stripes with different contrasts and polarities, representing the values and directions of the conductivity changes of the scanned layer. The favorable results provide solid evidence for transducer selection and suggest potential practical applications of MAT-MI in biomedical imaging.展开更多
Bottomless electromagnetic cold crucible is a new apparatus for continuous melting and directional solidification;however,improving its power efficiency and optimizing the configuration are important for experiment an...Bottomless electromagnetic cold crucible is a new apparatus for continuous melting and directional solidification;however,improving its power efficiency and optimizing the configuration are important for experiment and production.In this study,a 3-D finite element (FE) method based on experimental verification was applied to calculate the magnetic flux density (Bz).The effects of the power parameters and the induction coil on the magnetic field distribution in the cold crucible were investigated.The results show that higher current intensity and lower frequency are beneficial to the increase of Bz at both the segment midpoint and the slit location.The induction coil with racetrack section can induce greater Bz,and a larger gap between the induction coil and the shield ring increases Bz.The mechanism for this effect is also discussed.展开更多
Due to the unique magnetic, mechanical and thermal properties, magnetic nanoparticles(MNPs) have comprehensive applications as the contrast and therapeutic agents in biomedical imaging and magnetic hyperthermia. The l...Due to the unique magnetic, mechanical and thermal properties, magnetic nanoparticles(MNPs) have comprehensive applications as the contrast and therapeutic agents in biomedical imaging and magnetic hyperthermia. The linear and nonlinear magnetoacoustic responses determined by the magnetic properties of MNPs have attracted more and more attention in biomedical engineering. By considering the relaxation time of MNPs, we derive the formulae of second harmonic magnetoacoustic responses(2H-MARs) for a cylindrical MNP solution model based on the mechanical oscillations of MNPs in magnetoacoustic tomography with magnetic induction(MAT-MI). It is proved that only the second harmonic magnetoacoustic oscillations can be generated by MNPs under an alternating magnetic excitation. The acoustic pressure of the 2H-MAR is proportional to the square of the magnetic field intensity and exhibits a linear increase with the concentration of MNPs. Numerical simulations of the 2H-MAR are confirmed by the experimental measurements for various magnetic field intensities and solution concentrations using a laser vibrometer. The favorable results demonstrate the feasibility of the harmonic measurements without the fundamental interference of the electromagnetic excitation, and suggest a new harmonic imaging strategy of MAT-MI for MNPs with enhanced spatial resolution and improved signal-to-noise ratio in biomedical applications.展开更多
As a kind of multi-physics imaging approach integrating the advantages of electrical impedance tomography and ul- trasound imaging with the improved spatial resolution and image contrast, magneto-acoustic tomography w...As a kind of multi-physics imaging approach integrating the advantages of electrical impedance tomography and ul- trasound imaging with the improved spatial resolution and image contrast, magneto-acoustic tomography with magnetic induction (MAT-MI) is demonstrated to have the capability of electrical impedance contrast imaging for biological tissues with conductivity differences. By being detected with a strong directional transducer, abrupt pressure change is proved to be generated by the gradient of the induced Lorentz force along the force direction at conductivity boundary. A simplified boundary normal pressure (BNP)-based conductivity reconstruction algorithm is proposed and the formula for conductivity distribution inside the object with the clear physical meaning of pressure derivative, is derived. Numerical simulations of acoustic pressure and conductivity reconstruction are conducted based on a 2-layer eccentric cylindrical phantom model using Hilbert transform. The reconstructed two-dimensional conductivity images accord well with the model, thus success- fully making up the deficiency of only imaging conductivity boundary in traditional MAT-MI. The proposed method is also demonstrated to have a spatial resolution of one wavelength. This study provides a new method of reconstructing accurate electrical conductivity and suggests the potential applications of MAT-MI in imaging biological tissues with conductivity difference.展开更多
Experimental and theoretical researches performed by the author (period: 1969-present) showed that magnetic spinor particles (magnetic charges) are real structural components of atoms and substance and immediate sourc...Experimental and theoretical researches performed by the author (period: 1969-present) showed that magnetic spinor particles (magnetic charges) are real structural components of atoms and substance and immediate sources of all magnetic fields and magnetic manifestations in Nature. Magnetic charges, that constitute together with electrical charges atomic shells got of title: magnetons and antimagnetons (respectively with charges g−and g+ under fundamental condition: g = e). Furthermore, in addition to participating in structures of atomic shells, the magnetic charges exist in potential and even in real zones conduction of solids. The magnetic and electric spinor particles in atoms and substance exist in form such of the spinor associations as the magnetic and electric bispinors. Under influence of external magnetic field in conductor being implemented polarization of magnetic bispinors with formation of magnetic dipoles. Internal fields magnetic dipoles is directed against an external magnetic field and is a simple explanation of such a physical manifestation as diamagnetism. During the rotation of these dipoles in the conductor are formed of the vortex magnetic dipole fields, which and create an electromotive force, i.e. are responsible for the electromagnetic induction. Author proposed new magneto-electric technology called the magnetoelectric induction, as the result of which the permanent current of magnetic charges is created. However, such currents may be implemented solely in the superconductors. In the article presented the main reasons which more hundred year old hinder recognition and technical use of the real magnetic charges and their currents what considerably slow down the global scientific and technological progress.展开更多
In response to the primary electric field originated by the fluid-core-dynamo, electric charges accumulate at the boundaries of a solid conducting D″ layer due to the poor circuitry conditions until the irrotational ...In response to the primary electric field originated by the fluid-core-dynamo, electric charges accumulate at the boundaries of a solid conducting D″ layer due to the poor circuitry conditions until the irrotational primary electric field is neutralized. The neutralization undoes the internal induction excited by the primary electric field and, as a result, eliminates the secondary toroidal magnetic field inside the D″. The primary magnetic field generated by the fluid-core-dynamo gives rise to a sustainable secondary poloidal magnetic field inside the conducting D″ layer. We introduce the general kinematic boundary conditions that are valid with different induction processes and parameter jumps across the core mantle boundary.We find by dimensional analysis that the strength of the secondary poloidal magnetic field is much weaker, by a factor of ~10-2, than the irrotational primary. These findings indicate that the D' is in effect an insulator for the geodynamo regardless of its material composition. Any mechanism for the coremantle magnetic coupling should take this fact into consideration.展开更多
In large-scale electric machines, unbalanced magnetic pull (UMP) caused by eccentricity usually results in stator-rotor rub, so it is necessary to investigate the amplitude and the influencing factors. This paper ta...In large-scale electric machines, unbalanced magnetic pull (UMP) caused by eccentricity usually results in stator-rotor rub, so it is necessary to investigate the amplitude and the influencing factors. This paper takes the squirrel-cage induction motor as an example. A magnetic loop model of an induction motor is established by an analytical method. The impact of stator winding setup (parallel branch and pole pairs) on each magnetomotive force (MMF) and unbalanced magnetic pull is analyzed. Using the finite element simulation method, the spatial and time distribution of flux density of the rotor outer circle under static eccentricity is obtained, and the unbalanced magnetic pull calculation caused by static eccentricity is completed. The conclusion of the influence of stator winding on the size of unbalanced magnetic pull provides reliable gist for motor noise and vibration analysis, and especially provides an important reference for large induction motor design.展开更多
A novel transient rotor current control scheme is proposed in this paper for a doubly-fed induction generator(DFIG)equipped with a superconducting magnetic energy storage(SMES) device to enhance its transient volt...A novel transient rotor current control scheme is proposed in this paper for a doubly-fed induction generator(DFIG)equipped with a superconducting magnetic energy storage(SMES) device to enhance its transient voltage and frequency support capacity during grid faults. The SMES connected to the DC-link capacitor of the DFIG is controlled to regulate the transient dc-link voltage so that the whole capacity of the grid side converter(GSC) is dedicated to injecting reactive power to the grid for the transient voltage support. However, the rotor-side converter(RSC) has different control tasks for different periods of the grid fault. Firstly, for Period I, the RSC injects the demagnetizing current to ensure the controllability of the rotor voltage. Then, since the dc stator flux degenerates rapidly in Period II, the required demagnetizing current is low in Period II and the RSC uses the spare capacity to additionally generate the reactive(priority) and active current so that the transient voltage capability is corroborated and the DFIG also positively responds to the system frequency dynamic at the earliest time. Finally, a small amount of demagnetizing current is provided after the fault clearance. Most of the RSC capacity is used to inject the active current to further support the frequency recovery of the system. Simulations are carried out on a simple power system with a wind farm. Comparisons with other commonly used control methods are performed to validate the proposed control method.展开更多
Mn_(0.3)Zn_(0.3)Co_xFe_(2.4-x)O_4 series magnetic nanoparticles are prepared by the high-temperature organic solvent method, and Mn_(0.3)Zn_(0.3)Co_xFe_(2.4-x)O_4@SiO_2 composite nanoparticles are prepared by the reve...Mn_(0.3)Zn_(0.3)Co_xFe_(2.4-x)O_4 series magnetic nanoparticles are prepared by the high-temperature organic solvent method, and Mn_(0.3)Zn_(0.3)Co_xFe_(2.4-x)O_4@SiO_2 composite nanoparticles are prepared by the reverse microemulsion method. The as-prepared samples are characterized, and the results show that the magnetic anisotropy constant of nanoparticles increases with the cobalt content, and the magnetic thermal induction shows a trend of increasing first and then decreasing. The optimal magnetic thermal induction is obtained at x = 0.12 with a specific loss power of 2086 w/gmetal, which is a bright prospect in clinical magnetic hyperthermia.展开更多
We discuss a thermoelectric energy generation (TEG) technique by employing a thermomechanical model of a drinking bird (DB). The motion of a drinking bird is produced by the entropy-flow explained by the second law of...We discuss a thermoelectric energy generation (TEG) technique by employing a thermomechanical model of a drinking bird (DB). The motion of a drinking bird is produced by the entropy-flow explained by the second law of thermodynamics, which is one of the fundamental laws of heat engines. We propose a disk-magnet electromagnetic induction (DM-EMI) employed to the motion of a drinking bird. The generalization of DM-EMI to heat engines for?mechanoelectric?energy conversions and properties of extracted electric powers are specifically discussed. The electric power of DM-EMI has a limited power generation characteristic to a mechanical rotation produced by heat engines, but it will be very useful for practical applications to wind turbines, coal-fired and nuclear power plant for?mechanoelectric?energy conversions. The DM-EMI will contribute to environmental problems to maintain clean and susceptible energy as one of?energy?harvesting technologies.展开更多
A three-dimensional electromagnetic thermal coupled model of a 45#steel strip during longitudinal magnetic flux induction heating was established in this study.The influence of different power levels,frequencies,and e...A three-dimensional electromagnetic thermal coupled model of a 45#steel strip during longitudinal magnetic flux induction heating was established in this study.The influence of different power levels,frequencies,and electromagnetic shielding on the magnetic induction intensity and the heating of parts of different materials around the inductor was analyzed by calculating the magnetic induction intensity around the longitudinal flux induction heater under different conditions.The results show that leakage flux can be reduced up to 49%by electromagnetic shielding.The higher the frequency,the greater the electromagnetic shielding effect,and the lower the magnetic leakage around the inductor.Conversely,the higher the power,the greater the magnetic induction around the inductor.By adding electromagnetic shielding to reduce magnetic leakage of the inductor and replacing the metal part material around the inductor with stainless steel,the heat generation of the parts around the inductor can be greatly reduced.展开更多
The complex interaction between material properties in an induction heating circuit was studied by multi physics simulation and by experimental verification in a full-scale laboratory heater. The work aims to illustra...The complex interaction between material properties in an induction heating circuit was studied by multi physics simulation and by experimental verification in a full-scale laboratory heater. The work aims to illustrate the complexity of the system of interacting materials, but also to propose a method to verify properties of soft magnetic composite materials in an integrated system and to identify which properties are the most critical under different circumstances and load cases. Heat losses at different loads were primarily studied, from DC currents to AC currents at 15, 20 and 25 kHz, respectively. A FE model for magnetic simulation was correlated with a corresponding model for heat simulation. The numerical model, as well as the established input material data, could be verified through the experimental measurements. In this particular study, the current loss in the litz wire was the dominant heat source, thus making the thermal conductivity of the SMC the most important property in this material.展开更多
文摘Magnetohydrodynamic(MHD)induction pumps are contactless pumps able to withstand harsh environments.The rate of fluid flow through the pump directly affects the efficiency and stability of the device.To explore the influence of induction pump settings on the related delivery speed,in this study,a numerical model for coupled electromagnetic and flow field effects is introduced and used to simulate liquid metal lithium flow in the induction pump.The effects of current intensity,frequency,coil turns and coil winding size on the velocity of the working fluid are analyzed.It is shown that the first three parameters have a significant impact,while changes in the coil turns have a negligible influence.The maximum increase in working fluid velocity within the pump for the parameter combination investigated in this paper is approximately 618%.As the frequency is increased from 20 to 60 Hz,the maximum increase in the mean flow rate of the working fluid is approximately 241%.These research findings are intended to support the design and optimization of these devices.
文摘The magnetic field generated in the air gap of the cage asynchronous machine and the harmonics of the magnetomotive forces creating that magnetic field,as well as the synchronous parasitic torques,radial magnetic forces have been discussed in great detail in the literature,but always separately,for a long time.However,systematization of the phenomenon still awaits.Therefore,it is worth summarizing the completeness of the phenomena in a single study–with a new approach at the same time-in order to reveal the relationships between them.The role of rotor slot number is emphasized much more than before.New formulas derived for both synchronous torques and radial magnetic forces are used for further investigation.It will be shown that both phenomena in subject must be treated together.Formulas will be provided to take into account attenuation.Design guide will be provided to avoid dangerous rotor slot numbers.It will be shown that the generation of synchronous torques and radial magnetic forces do not depend–in this new approach-on the slot combination,but on the rotor slot number itself.
文摘Electricity and magnetism and electromagnetic induction are phenomena that can be perceived by people. But their interpretation and theoretical study took a long time. The theoretical research on electricity began with the discovery of Coulomb’s law in 1785, while the theoretical research on magnetism began with the discovery of Oersted’s Law in 1820. From the 1850s to the 1870s, Maxwell summarized a set of theoretical equations for electromagnetism based on some laws of predecessors. However, this set of equations contains a few statistical relationships and empirical concepts, so it is difficult to explain the physical nature of electromagnetic phenomena and principles. This paper explained that the macro phenomenon of electricity is the separation of unlike charges of new electrons produced by the orthogonal collision of old particles under the action of external forces. The physical nature of magnetism is the potential energy (magnetic energy) and information associated with the overall orientation of the moving electrons solidly recorded in the material. The physical principle of electromagnetic induction describes how change in electric current intensity generates change in magnetic intensity and vice versa through orthogonal interaction of ordered electrons. This theoretical interpretation does not require the concepts of traditional electromagnetic forces, electromagnetic fields, magnetic moments, and magnetic domains.
基金Project supported by the National Natural Science Foundation of China (Grant No.12074130)the Natural Science Foundation of Guangdong Province (Grant No.2021A1515012340)。
文摘Recent experimental findings have demonstrated the occurrence of superconductivity in Bernal bilayer graphene when induced by a magnetic field.In this study,we conduct a theoretical investigation of the potential pairing symmetry within this superconducting system.By developing a theoretical model,we primarily calculate the free energy of the system with p+ip-wave parallel spin pairing,p+ip-wave anti-parallel spin pairing and d+i d-wave pairing symmetry.Our results confirm that the magnetic field is indeed essential for generating the superconductivity.We discover that the p+ip-wave parallel spin pairing leads to a lower free energy for the system.The numerical calculations of the energy band structure,zero-energy spectral function and density of states for each of the three pairing symmetries under consideration show a strong consistency with the free energy results.
基金supported financially by the National Natural Science Foundation of China(42250101)the Macao Foundation and Macao Science and Technology Development Fund(0001/2019/A1).
文摘Geomagnetic storms are rapid disturbances of the Earth’s magnetosphere.They are related to many geophysical phenomena and have large influences on human activities.Observing and studying geomagnetic storms is thus of great significance to both scientific research and geomagnetic hazards prevention.The Macao Science Satellite-1(MSS-1)project includes two high-precision Chinese geomagnetic satellites successfully launched on May 21,2023.The main purpose of MSS-1 is to accurately measure the Earth’s magnetic field.Here,we analyze early MSS-1 geomagnetic field measurements and report observations of two recent geomagnetic storms that occurred on March 24,2024 and May 11,2024.We also calculate the related geoelectric fields as an initial step towards a quantitative assessment of geomagnetic hazards.
文摘The longitudinal wave term within Faraday’s law of electromagnetic induction (Faraday’s law) underwent recovery to ensure its suitability for theoretical derivation of the equation governing longitudinal electromagnetic (LEM) waves. The revised Maxwell’s equations include the crucial parameters being the attenuation time constants of magnetic vortex potential and electric vortex potential generated by external electromagnetic field within the propagation medium. Specific expressions for them are obtained through theoretical analysis. Subsequently, a model for propagating magnetic P-wave generated by the superposition of a left-handed photo and a right-handed photon in a vacuum is formulated based on reevaluated total current law and revised Faraday’s law, covering wave equations, energy equation, as well as propagation mode involving mutual induction and conversion between scalar magnetic field and vortex electric field. Furthermore, through theoretical derivations centered around magnetic P-wave, evidence was presented regarding its ability to absorb huge free energy through the entangled interaction between zero-point vacuum energy field and the torsion field produced by the vortex electric field.
基金Project supported by the National Basic Research Program of China (Grant No. 2011CB707900), the National Natural Science Foundation of China (Grant No. 10974098), the Natural Science Foundation of Jiangsu Province, China (Grant No. BK2009407), and the Specialized Research Fund for Doctoral Program of High Education of China (Grant No. 20093207120003).
文摘An acoustic dipole radiation model for magnetoacoustic tomography with magnetic induction (MAT-MI) is pro- posed, based on the analyses of one-dimensional tissue vibration, three-dimensional acoustic dipole radiation and acoustic waveform detection with a planar piston transducer. The collected waveforms provide information about the conductiv- ity boundaries in various vibration intensities and phases due to the acoustic dipole radiation pattern. Combined with the simplified back projection algorithm, the conductivity configuration of the measured layer in terms of shape and size can be reconstructed with obvious border stripes. The numerical simulation is performed for a two-layer cylindrical phantom model and it is also verified by the experimental results of MAT-MI for a tissue-like sample phantom. The proposed model suggests a potential application of conductivity differentiation and provides a universal basis for the further study of conductivity reconstruction for MAT-MI.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.51507171,and 61427806)
文摘Magneto–acoustic tomography with magnetic induction(MAT-MI) is a multiphysics coupled imaging technique that is combined with electrical impedance tomography and ultrasound imaging. In order to study the influence of adding magnetic nanoparticles as a contrast agent for MAT-MI on its physical process, firstly, we analyze and compare the electromagnetic and acoustical properties of MAT-MI theoretically before and after adding magnetic nanoparticles, and then construct a two-dimensional(2 D) planar model. Under the guidance of space-time separation theory, we determine the reasonable simulation conditions and solve the electromagnetic field and sound field physical processes in the two modes by using the finite element method. The magnetic flux density, sound pressure distribution, and related one-dimensional(1 D), 2 D, and three-dimensional(3 D) images are obtained. Finally, we make a qualitative and quantitative analysis based on the theoretical and simulation results. The research results show that the peak time of the time item separated from the sound source has a corresponding relationship with the peak time of the sound pressure signal. At this moment, MAMPTMI produces larger sound pressure signals, and the sound pressure distribution of the MAMPT-MI is more uniform, which facilitates the detection and completion of sound source reconstruction. The research results may lay the foundation for the MAT-MI of magnetically responsive nanoparticle in subsequent experiments and even clinical applications.
基金Project supported by the National Basic Research Program of China(Grant No.2011CB707900)the National Natural Science Foundation of China(Grant Nos 11274176 and 11474166)the Priority Academic Program Development of Jiangsu Higher Education Institutions,China
文摘Based on the acoustic radiation theory of a dipole source, the influence of the transducer reception pattern is studied for magnetoacoustic tomography with magnetic induction(MAT-MI). Numerical studies are conducted to simulate acoustic pressures, waveforms, and reconstructed images with unidirectional, omnidirectional, and strong directional transducers.With the analyses of equivalent and projection sources, the influences of the model dimension and the layer effect are qualitatively analyzed to evaluate the performance of MAT-MI. Three-dimensional simulation studies show that the strong directional transducer with a large radius can reduce the influences of equivalent sources, projection sources, and the layer effect effectively, resulting in enhanced pressure and improved image contrast, which is beneficial for boundary pressure extraction in conductivity reconstruction. The reconstructed conductivity contrast images present the conductivity boundaries as stripes with different contrasts and polarities, representing the values and directions of the conductivity changes of the scanned layer. The favorable results provide solid evidence for transducer selection and suggest potential practical applications of MAT-MI in biomedical imaging.
基金financially supported by the National Basic Research Program of China (Grant No.2011CB605504)
文摘Bottomless electromagnetic cold crucible is a new apparatus for continuous melting and directional solidification;however,improving its power efficiency and optimizing the configuration are important for experiment and production.In this study,a 3-D finite element (FE) method based on experimental verification was applied to calculate the magnetic flux density (Bz).The effects of the power parameters and the induction coil on the magnetic field distribution in the cold crucible were investigated.The results show that higher current intensity and lower frequency are beneficial to the increase of Bz at both the segment midpoint and the slit location.The induction coil with racetrack section can induce greater Bz,and a larger gap between the induction coil and the shield ring increases Bz.The mechanism for this effect is also discussed.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.11934009,11974187,and 11604156)。
文摘Due to the unique magnetic, mechanical and thermal properties, magnetic nanoparticles(MNPs) have comprehensive applications as the contrast and therapeutic agents in biomedical imaging and magnetic hyperthermia. The linear and nonlinear magnetoacoustic responses determined by the magnetic properties of MNPs have attracted more and more attention in biomedical engineering. By considering the relaxation time of MNPs, we derive the formulae of second harmonic magnetoacoustic responses(2H-MARs) for a cylindrical MNP solution model based on the mechanical oscillations of MNPs in magnetoacoustic tomography with magnetic induction(MAT-MI). It is proved that only the second harmonic magnetoacoustic oscillations can be generated by MNPs under an alternating magnetic excitation. The acoustic pressure of the 2H-MAR is proportional to the square of the magnetic field intensity and exhibits a linear increase with the concentration of MNPs. Numerical simulations of the 2H-MAR are confirmed by the experimental measurements for various magnetic field intensities and solution concentrations using a laser vibrometer. The favorable results demonstrate the feasibility of the harmonic measurements without the fundamental interference of the electromagnetic excitation, and suggest a new harmonic imaging strategy of MAT-MI for MNPs with enhanced spatial resolution and improved signal-to-noise ratio in biomedical applications.
基金supported by the National Natural Science Foundation of China(Grant Nos.11474166 and 11604156)the Natural Science Foundation of Jiangsu Province,China(Grant No.BK20161013)+1 种基金the Postdoctoral Science Foundation of China(Grant No.2016M591874)the Priority Academic Program Development of Jiangsu Provincial Higher Education Institutions,China
文摘As a kind of multi-physics imaging approach integrating the advantages of electrical impedance tomography and ul- trasound imaging with the improved spatial resolution and image contrast, magneto-acoustic tomography with magnetic induction (MAT-MI) is demonstrated to have the capability of electrical impedance contrast imaging for biological tissues with conductivity differences. By being detected with a strong directional transducer, abrupt pressure change is proved to be generated by the gradient of the induced Lorentz force along the force direction at conductivity boundary. A simplified boundary normal pressure (BNP)-based conductivity reconstruction algorithm is proposed and the formula for conductivity distribution inside the object with the clear physical meaning of pressure derivative, is derived. Numerical simulations of acoustic pressure and conductivity reconstruction are conducted based on a 2-layer eccentric cylindrical phantom model using Hilbert transform. The reconstructed two-dimensional conductivity images accord well with the model, thus success- fully making up the deficiency of only imaging conductivity boundary in traditional MAT-MI. The proposed method is also demonstrated to have a spatial resolution of one wavelength. This study provides a new method of reconstructing accurate electrical conductivity and suggests the potential applications of MAT-MI in imaging biological tissues with conductivity difference.
文摘Experimental and theoretical researches performed by the author (period: 1969-present) showed that magnetic spinor particles (magnetic charges) are real structural components of atoms and substance and immediate sources of all magnetic fields and magnetic manifestations in Nature. Magnetic charges, that constitute together with electrical charges atomic shells got of title: magnetons and antimagnetons (respectively with charges g−and g+ under fundamental condition: g = e). Furthermore, in addition to participating in structures of atomic shells, the magnetic charges exist in potential and even in real zones conduction of solids. The magnetic and electric spinor particles in atoms and substance exist in form such of the spinor associations as the magnetic and electric bispinors. Under influence of external magnetic field in conductor being implemented polarization of magnetic bispinors with formation of magnetic dipoles. Internal fields magnetic dipoles is directed against an external magnetic field and is a simple explanation of such a physical manifestation as diamagnetism. During the rotation of these dipoles in the conductor are formed of the vortex magnetic dipole fields, which and create an electromotive force, i.e. are responsible for the electromagnetic induction. Author proposed new magneto-electric technology called the magnetoelectric induction, as the result of which the permanent current of magnetic charges is created. However, such currents may be implemented solely in the superconductors. In the article presented the main reasons which more hundred year old hinder recognition and technical use of the real magnetic charges and their currents what considerably slow down the global scientific and technological progress.
文摘In response to the primary electric field originated by the fluid-core-dynamo, electric charges accumulate at the boundaries of a solid conducting D″ layer due to the poor circuitry conditions until the irrotational primary electric field is neutralized. The neutralization undoes the internal induction excited by the primary electric field and, as a result, eliminates the secondary toroidal magnetic field inside the D″. The primary magnetic field generated by the fluid-core-dynamo gives rise to a sustainable secondary poloidal magnetic field inside the conducting D″ layer. We introduce the general kinematic boundary conditions that are valid with different induction processes and parameter jumps across the core mantle boundary.We find by dimensional analysis that the strength of the secondary poloidal magnetic field is much weaker, by a factor of ~10-2, than the irrotational primary. These findings indicate that the D' is in effect an insulator for the geodynamo regardless of its material composition. Any mechanism for the coremantle magnetic coupling should take this fact into consideration.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.51677051 and 51377039)the Fund from the Anhui Province Key Laboratory of Large-scale Submersible Electric Pump and Accoutrements
文摘In large-scale electric machines, unbalanced magnetic pull (UMP) caused by eccentricity usually results in stator-rotor rub, so it is necessary to investigate the amplitude and the influencing factors. This paper takes the squirrel-cage induction motor as an example. A magnetic loop model of an induction motor is established by an analytical method. The impact of stator winding setup (parallel branch and pole pairs) on each magnetomotive force (MMF) and unbalanced magnetic pull is analyzed. Using the finite element simulation method, the spatial and time distribution of flux density of the rotor outer circle under static eccentricity is obtained, and the unbalanced magnetic pull calculation caused by static eccentricity is completed. The conclusion of the influence of stator winding on the size of unbalanced magnetic pull provides reliable gist for motor noise and vibration analysis, and especially provides an important reference for large induction motor design.
基金supported by the National Natural Science Foundation of China(Grant No.51307124)the Major Program of the National Natural Science Foundation of China(Grant No.51190105)
文摘A novel transient rotor current control scheme is proposed in this paper for a doubly-fed induction generator(DFIG)equipped with a superconducting magnetic energy storage(SMES) device to enhance its transient voltage and frequency support capacity during grid faults. The SMES connected to the DC-link capacitor of the DFIG is controlled to regulate the transient dc-link voltage so that the whole capacity of the grid side converter(GSC) is dedicated to injecting reactive power to the grid for the transient voltage support. However, the rotor-side converter(RSC) has different control tasks for different periods of the grid fault. Firstly, for Period I, the RSC injects the demagnetizing current to ensure the controllability of the rotor voltage. Then, since the dc stator flux degenerates rapidly in Period II, the required demagnetizing current is low in Period II and the RSC uses the spare capacity to additionally generate the reactive(priority) and active current so that the transient voltage capability is corroborated and the DFIG also positively responds to the system frequency dynamic at the earliest time. Finally, a small amount of demagnetizing current is provided after the fault clearance. Most of the RSC capacity is used to inject the active current to further support the frequency recovery of the system. Simulations are carried out on a simple power system with a wind farm. Comparisons with other commonly used control methods are performed to validate the proposed control method.
基金Supported by the National Natural Science Foundation of China under Grant Nos 51571146,51771124 and 51701130
文摘Mn_(0.3)Zn_(0.3)Co_xFe_(2.4-x)O_4 series magnetic nanoparticles are prepared by the high-temperature organic solvent method, and Mn_(0.3)Zn_(0.3)Co_xFe_(2.4-x)O_4@SiO_2 composite nanoparticles are prepared by the reverse microemulsion method. The as-prepared samples are characterized, and the results show that the magnetic anisotropy constant of nanoparticles increases with the cobalt content, and the magnetic thermal induction shows a trend of increasing first and then decreasing. The optimal magnetic thermal induction is obtained at x = 0.12 with a specific loss power of 2086 w/gmetal, which is a bright prospect in clinical magnetic hyperthermia.
文摘We discuss a thermoelectric energy generation (TEG) technique by employing a thermomechanical model of a drinking bird (DB). The motion of a drinking bird is produced by the entropy-flow explained by the second law of thermodynamics, which is one of the fundamental laws of heat engines. We propose a disk-magnet electromagnetic induction (DM-EMI) employed to the motion of a drinking bird. The generalization of DM-EMI to heat engines for?mechanoelectric?energy conversions and properties of extracted electric powers are specifically discussed. The electric power of DM-EMI has a limited power generation characteristic to a mechanical rotation produced by heat engines, but it will be very useful for practical applications to wind turbines, coal-fired and nuclear power plant for?mechanoelectric?energy conversions. The DM-EMI will contribute to environmental problems to maintain clean and susceptible energy as one of?energy?harvesting technologies.
文摘A three-dimensional electromagnetic thermal coupled model of a 45#steel strip during longitudinal magnetic flux induction heating was established in this study.The influence of different power levels,frequencies,and electromagnetic shielding on the magnetic induction intensity and the heating of parts of different materials around the inductor was analyzed by calculating the magnetic induction intensity around the longitudinal flux induction heater under different conditions.The results show that leakage flux can be reduced up to 49%by electromagnetic shielding.The higher the frequency,the greater the electromagnetic shielding effect,and the lower the magnetic leakage around the inductor.Conversely,the higher the power,the greater the magnetic induction around the inductor.By adding electromagnetic shielding to reduce magnetic leakage of the inductor and replacing the metal part material around the inductor with stainless steel,the heat generation of the parts around the inductor can be greatly reduced.
文摘The complex interaction between material properties in an induction heating circuit was studied by multi physics simulation and by experimental verification in a full-scale laboratory heater. The work aims to illustrate the complexity of the system of interacting materials, but also to propose a method to verify properties of soft magnetic composite materials in an integrated system and to identify which properties are the most critical under different circumstances and load cases. Heat losses at different loads were primarily studied, from DC currents to AC currents at 15, 20 and 25 kHz, respectively. A FE model for magnetic simulation was correlated with a corresponding model for heat simulation. The numerical model, as well as the established input material data, could be verified through the experimental measurements. In this particular study, the current loss in the litz wire was the dominant heat source, thus making the thermal conductivity of the SMC the most important property in this material.