Preliminary geological interpretation of long-wavelength magnetic anomalies over China and surrounding regions

Long-wavelength(>500 km)magnetic anomalies originating in the lithosphere were first found in satellite magnetic surveys.Compared to the striking magnetic anomalies around the world,the long-wavelength magnetic anomalies in China and surrounding regions are relatively weak.Specialized research on each of these anomalies has been quite inadequate;their geological origins remain unclear,in particular their connection to tectonic activity in the Chinese and surrounding regions.We focus on six magnetic high anomalies over the(1)Tarim Basin,(2)Sichuan Basin(3)Great Xing’an Range,(4)Barmer Basin,(5)Central Myanmar Basin,and(6)Sunda and Banda Arcs,and a striking magnetic low anomaly along the southern part of the Himalayan-Tibetan Plateau.We have analyzed their geological origins by reviewing related research and by detailed comparison with geological results.The tectonic backgrounds for these anomalies belong to two cases:either ancient basin basement,or subduction-collision zone.However,the geological origins of large-scale regional magnetic anomalies are always subject to dispute,mainly because of limited surface exposure of sources,later tectonic destruction,and superposition of multi-phase events.

Numerical Analysis on Magnetic-induced Shear Modulus of Magnetorheological Elastomers Based on Multi-chain Model

Based on the magnetic interaction energy, using derivative of the magnetic energy density, a model is proposed to compute the magnetic-induced shear modulus of magnetorheological elastomers. Taking into account the influences of particles in the same chain and the particles in all adjacent chains, the traditional magnetic dipole model of the magnetorheological elastomers is modified. The influence of the ratio of the distance etween adjacent chains to the distance between adjacent particles in a chain on the magnetic induced shear odulus is quantitatively studied. When the ratio is large, the multi-chain model is compatible with the single chain model, but when the ratio is small, the difference of the two models is significant and can not be neglected. Making certain the size of the columns and the distance between adjacent columns, after constructing the computational model of BCT structures, the mechanical property of the magnetorheological elastomers composed of columnar structures is analyzed. Results show that, conventional point dipole model has overrated the magnetic-induced shear modulus of the magnetorheological elastomers. From the point of increasing the magnetic-induced shear modulus, when the particle volume fraction is small, the chain-like structure exhibits better result than the columnar structure, but when the particle volume fraction is large,the columnar structure will be better.

Crustal structure of the western Indian shield: Model based on regional gravity and magnetic data

Regional surface gravity data and global satellite magnetic data have been utilized to generate a preliminary model of the crustal structure along a southwest-northeast profile （Gadra-Fatehpur） through western Rajasthan.The study area represents the western part of the Indian continental landmass which has undergone several major episodes of repeated subduction/collision,plume traces and rifting from Archaean to recent times.The temporal and spatial relationship between the various geotectonic provinces is quite complex,thereby limiting the emergence of a suitable crustal structure model for this region.Exposures of the Malani Igneous Suite （MIS）,a product of bimodal volcanism （～780 Ma）,and considered to be the third largest felsic magmatic province of the world,is evident along the profile and also to the southwest of the study area.The easternmost part of the profile is close to the DAFB （Delhi Aravalli Fold Belt）,a Proterozoic orogenic belt.This study probes the geometry of the different crustal units in terms of density and susceptibility variations in order to decipher the imprints of the major tectonic processes the region has undergone.In order to decipher the crustal geometry of the Gadra-Fatehpur profile,two NW-SE gravity and magnetic profile vertical sections （A-A＇ in the south and B-B＇ in the north） are modelled on the basis of the constraints provided from previous seismic models.The crustal model of the Gadra-Fatehpur profile is composed of alluvium,Tertiary sediments,MIS,Marwar Supergroup,low-density layers （LDLs） and the middle-lower crustal layers,with a distinct change in configuration from the southwest to northeast.The Moho dips from SW to NE,the MIS in the SW gives way to the thick pile of the Marwar Supergroup to the NE.The evolution of MIS has been suggested to have occurred as a consequence of delamination of the upper mantle.LDLs are incorporated in Gadra-Fatehpur model.In the SW,LDL （2550 kg/m3） lies below the MIS in the NE,another LDL （2604 kg/m3） is depicted below the mid-crustal layer.

A local spin study for magnetic model complex HHeH

Davidson and Clark’s equations for calculating the local spin of molecules were rewritten and simplified as matrices algebra. By applying our program, we calculated the local spin of O2 and NO molecules and obtained almost the same results as those by Davidson and Clark’s method. The local spin and the magnetic coupling constant J of the simple Van der Waals complex HHeH were calculated as well to investigate the relationship between the geometric structures and magnetic values.

Quantitative Metal Magnetic Memory Reliability Modeling for Welded Joints

Metal magnetic memory（MMM） testing has been widely used to detect welded joints. However, load levels, environmental magnetic field, and measurement noises make the MMM data dispersive and bring difficulty to quantitative evaluation. In order to promote the development of quantitative MMM reliability assessment, a new MMM model is presented for welded joints. Steel Q235 welded specimens are tested along the longitudinal and horizontal lines by TSC-2M-8 instrument in the tensile fatigue experiments. The X-ray testing is carried out synchronously to verify the MMM results. It is found that MMM testing can detect the hidden crack earlier than X-ray testing. Moreover, the MMM gradient vector sum K_（vs） is sensitive to the damage degree, especially at early and hidden damage stages. Considering the dispersion of MMM data, the K_（vs） statistical law is investigated, which shows that K_（vs） obeys Gaussian distribution. So K_（vs） is the suitable MMM parameter to establish reliability model of welded joints. At last, the original quantitative MMM reliability model is first presented based on the improved stress strength interference theory. It is shown that the reliability degree R gradually decreases with the decreasing of the residual life ratio T, and the maximal error between prediction reliability degree R_1 and verification reliability degree R_2 is 9.15%. This presented method provides a novel tool of reliability testing and evaluating in practical engineering for welded joints.

3-D Magnetic Sensor Module for Locating and Tracking MEMS Swallowable Capsule Based on Scalar Form of Magnetic Dipole Model

MEMS swallowable capsule is a novel technology in the non-invasive surgery. This technology provides a way to diagnose directly into the deep intestinal where the traditional invasive technology implemented, such as X-Ray, endoscopy. It is a key for us to locate and track the position of a MEMS capsule in clinical applications. To solve this problem, we implemented a magnetic sensor module based on the scalar form of the magnetic dipole model,which was designed with very small size （5.2 ＊ 2. 1 ＊ 1.2 em） and easy to assemble to satisfy the system requirement. Here we discuss in detail the principle of magnetic dipole model, rules of selecting sensor and functions of the module. Some trials are established to test the characteristic of the module. The results of the Cm experiment demonstrates that the module follows the rules of the new magnetic dipole model form.

The substorm current wedge and midnight sector partial ring current near substorm onset: A synthesis based on a magnetotail magnetic field geometry model

The Substorm Current Wedge （SCW） occurrence in the late growth and onset phases of substorms was proposed as the current system which disrupts cross-tail current by diverting it to the ionosphere. The closure current for the SCW originally was suggested to be the strong westward auroral electrojet （WEJ）. However, the SCW-WEJ system has no viable generator current. Similarly, the asymmetric or Partial Ring Current （PRC） increases in strength during the growth phase, and is sometimes associated with an enhanced Region 2 field-aligned current （FAC） closing to the ionosphere, but specifics of that closure have been lacking. Here we present a tmifying picture which includes the SCW post- and pre-midnight （AM and PM, respectively） currents and a generator current in the midnight portion of the PRC system, with these currents based upon a model of the nightside magnetotail magnetic geometry. That geometry consists of open north and south lobe regions surrounding a plasmasheet with two types of closed field line regions-stretched lines in the central part of the plasmasheet （SPS） and dipolar lines （DPS） between the low lati- tude boundary layer （LLBL） regions and the SPS. There is also an important plasmasheet transition region （TPS） in which the dipolar field near the plasmapause gradually transforms to stretched lines near the earthward edge of the SPS, and in which the midnight part of the PRC flows. We propose that our proposed near-onset current system consists of a central current which be- comes part of the midnight sector PRC and which is the generator, to which are linked two three-part current systems, one on the dawnside and one on the duskside. The three-part systems consist of up and down FACs closing as Pedersen currents in the iono- sphere. These 3-part systems are not activated until near-onset is reached, because of a lack of ionospheric conductivity in the appropriate locations where the Pedersen current closure occurs. The initial downward FAC of the 3-part dawnside system and the final upward FAC of the 3-part duskside system correspond to the AM and PM current segments, respectively, of the originally proposed SCW.

Deconfinement Phase Transition with External Magnetic Field in the Friedberg-Lee Model

The deconfinement phase transition with external magnetic field is investigated in the Friedberg-Lee model. We expand the potentiM around the two locM minima of the first-order deconfinement phase transition and extract the ground state of the system in the frame of functional renormalization group. By solving the flow equations we find that the magnetic field displays a catalysis effect and it becomes more difficult to break through the confinement.

Thermal Entanglement in the Pure Dzyaloshinskii-Moriya Model with Magnetic Field

We investigate the effects of the directions of Dzyaloshinskii Moriya （DM） interaction and magnetic field on the thermal entanglement in the pure DM model. It is found that when the Hamiltonian is H1 = D. （σ1 ＋σ2） ＋B.σ1, the entanglement can reach its maximum if the directions of the magnetic field and the DM vector are parallel. In addition, when the Hamiltonian is H2 = D @ （σ1 σ2） ＋ B. （σ1 ＋ σ2）, if the directions of the magnetic field and the DM vector are perpendicular in a high magnetic field, or their directions are parMlel in a weak magnetic field, the entanglement can also reach its maximum. Thus the entanglement can be enhanced by adjusting the direction of the external magnetic field, and this is feasible within the current experimental technology.

Modelling the unsteady melt flow under a pulsed magnetic field

A numerical model for the unsteady flow under a pulsed magnetic field of a solenoid is developed, in which magnetohydrodynamic flow equations decouple into a transient magnetic diffusion equation and unsteady Navier–Stokes equations in conjunction with two equations of the k–ε turbulent model. A Fourier series method is used to implement the boundary condition of magnetic flux density under multiple periods of a pulsed magnetic field （PMF）. The numerical results are compared with the theoretical or experimental results to validate the model under a time-harmonic magnetic field; it is found that the toroidal vortex pair is the dominating structure within the melt flow under a PMF. The velocity field of a molten melt is in a quasi-steady state after several periods; changing the direction of the electromagnetic force causes the vibration of the melt surface under a PMF.

Design of Rotor Magnetic Barrier Structure of Built-in Permanent Magnet Motor Based on Taguchi Method

In this paper,a 20kW vehicle built-in permanent magnet synchronous motor is taken as an example,and a magnetic barrier structure is added to the rotor of the motor to solve the uneven saturation problem of the rotor side magnetic bridge.This structure improves the air-gap flux density waveform of the motor by influencing the internal magnetic flux path of the motor rotor,thus improving the sine of the no-load back EMF waveform of the motor and reducing the torque ripple of the motor.At the same time,Taguchi method is used to optimize the structural parameters of the added magnetic barrier.In order to facilitate the analysis of its uneven saturation phenomenon and improve the optimization effect,a simple equivalent magnetic network(EMN)model considering the uneven saturation of rotor magnetic bridge is established in this paper,and the initial values of optimization factors are selected based on this model.Finally,the no-load back EMF waveform distortion rate,torque ripple and output torque of the optimized motor are compared and analyzed,and the influence of magnetic barrier structure parameters on the electromagnetic performance of the motor is also analyzed.The results show that the optimized motor can not change the output torque of the motor as much as possible on the basis of reducing the waveform distortion rate of no-load back EMF and torque ripple.

Characterization of the Elastic-plastic Region Based on Magnetic Memory Effect

Detecting stress concentration, especially critical stress state leading to structure damage or failure, is one of the most important tasks of equipment diagnosis. Metal magnetic memory technique needs further research to evaluate stress concentration quantitatively due to ambiguous physical mechanism, though it has potential to detect early defects in ferromagnetic materials. Mild Q235 steel defective specimens in demagnetization state were loaded in tension up to visible necking, with magnetic memory signals measurement made at increasing stress levels. Magnetic signals varied greatly under first several loadings and subsequently tended to stability in the elastic region, which showed that the magnetization always approaches the anhysteretic magnetization curve and was explained by the theory of magnetomechanical effect. In the plastic stage, an abnormal wave occurred in the stress concentration zone and its height value was sensitive to plastic deformation levels and dependent on the distance between the probe and defect, in accordance with the simulation results based on the magnetic dipole model. Different magnetic signal characteristics in the elastic-plastic region indicate that the magnetic memory technique can identify macroyielding and early damage, which is of profound significance for ensuring safe operation of equipment in service.

An analysis of the characteristics of crustal magnetic anomaly in China based on CHAMP satellite data

Based on the observation data of CHAMP satellite from 2006 to 2009, a 2D crustal magnetic anomaly model in China is established to study the distribution characteristics of crustal magnetic anomaly. In this paper, the 2D anomaly model is derived from the Legendre polynomial expansion of harmonic term N =6-50. The result shows that many elaborate structures reflected in magnetic anomaly map well correspond to the geologic structures in China and its adjacent area. The magnetic anomaly at low satellite height behaves complexly, which is mainly caused by the magnetic disturbance of shallow rocks.In contrast, the magnetic field isolines at high satellite height are relatively sparse and only magnetic anomalies of deep crust are reflected. This fact implies that the 2D model of crustal magnetic anomaly provides an important method of the space prolongation of geomagnetic field, and is of theoretical and practice importance in geologic structure analysis and geophysical prospecting.

Magnetostrictive and Kinematic Model Considering the Dynamic Hysteresis and Energy Loss for GMA

Due to the influence of magnetic hysteresis and energy loss inherent in giant magnetostrictive materials （GMM）, output displacement accuracy of giant magnetostrictive actuator （GMA） can not meet the precision and ultra precision machining. Using a GMM rod as the core driving element, a GMA which may be used in the field of precision and ultra precision drive engineering is designed through modular design method. Based on the Armstrong theory and elastic Gibbs free energy theory, a nonlinear magnetostriction model which considers magnetic hysteresis and energy loss characteristics is established. Moreover, the mechanical system differential equation model for GMA is established by utilizing D＇Alembert＇s principle. Experimental results show that the model can preferably predict magnetization property, magnetic potential orientation, energy loss for GMM. It is also able to describe magnetostrictive elongation and output displacement of GMA. Research results will provide a theoretical basis for solving the dynamic magnetic hysteresis, energy loss and working precision for GMA fundamentally.

Hard magnetization direction and its relation with magnetic permeability of highly grain-oriented electrical steel

The magnetic properties of highly grain-oriented electrical steel vary along different directions. In order to investigate these properties, standard Epstein samples were cut at different angles to the rolling direction. The hard magnetization direction was found at an angle of 60° to the rolling direction. To compare the measured and fitting curves, when the magnetic field intensity is higher than 7000 A/m, it is appropriate to simulate the relation of magnetic permeability and magnetization angle using the conventional elliptical model. When the magnetic field intensity is less than 3000 A/m, parabolic fitting models should be used; but when the magnetic field intensity is between 3000 and 7000 A/m, hybrid models with high accuracy, as proposed in this paper, should be applied. Piecewise relation models of magnetic permeability and magnetization angle are significant for improving the accuracy of electromagnetic engineering calculations of electrical steel, and these new models could be applied in further industrial applications.

Interaction forces between soft magnetic particles in uniform and non-uniform magnetic fields

The influence of the magnetization of a soft magnetic sphere on the surrounding magnetic field is measured and characterized.The interaction force between two soft magnetic particles is directly measured using an ultra precision load sensor in uniform and non-uniform magnetic fields. The interaction force largely follows an inverse fourth power law as a function of separation distance between particle centers. At small distances,the effect of magnetization of one particle on the magnetization of its adjacent particle causes the attractive（repulsive） force to be larger（smaller） than that predicted by the inverse fourth power law.The theoretical prediction based on a modified dipole model,that takes into account the coupling effect of the magnetization among soft magnetic particles,gives excellent agreement with the measured force in a uniform magnetic field.The interaction force under a non-uniform applied magnetic field can be reasonably predicted using the dipole-dipole interaction model when the local magnetic field is used to determine the magnetization.

Experiments and SPICE simulations of double MgO-based perpendicular magnetic tunnel junction

We investigate properties of perpendicular anisotropy magnetic tunnel junctions(pMTJs) with a stack structure MgO/CoFeB/Ta/CoFeB/MgO as the free layer(or recording layer),and obtain the necessary device parameters from the tunneling magnetoresistance(TMR) vs.field loops and current-driven magnetization switching experiments.Based on the experimental results and device parameters,we further estimate current-driven switching performance of pMTJ including switching time and power,and their dependence on perpendicular magnetic anisotropy and damping constant of the free layer by SPICE-based circuit simulations.Our results show that the pMTJ cells exhibit a less than 1 ns switching time and write energies <1.4 pJ;meanwhile the lower perpendicular magnetic anisotropy(PMA) and damping constant can further reduce the switching time at the studied range of damping constant α <0.1.Additionally,our results demonstrate that the pMTJs with the thermal stability factor■73 can be easily transformed into spin-torque nano-oscillators from magnetic memory as microwave sources or detectors for telecommunication devices.

Modeling of Inner Surface Modification of a Cylindrical Tube by Plasma-Based Low-Energy Ion Implantation

The inner surface modification process by plasma-based low-energy ion implantation（PBLEII）with an electron cyclotron resonance（ECR）microwave plasma source located at the central axis of a cylindrical tube is modeled to optimize the low-energy ion implantation parameters for industrial applications.In this paper,a magnetized plasma diffusion fluid model has been established to describe the plasma nonuniformity caused by plasma diffusion under an axial magnetic field during the pulse-off time of low pulsed negative bias.Using this plasma density distribution as the initial condition,a sheath collisional fluid model is built up to describe the sheath evolution and ion implantation during the pulse-on time.The plasma nonuniformity at the end of the pulse-off time is more apparent along the radial direction compared with that in the axial direction due to the geometry of the linear plasma source in the center and the difference between perpendicular and parallel plasma diffusion coefficients with respect to the magnetic field.The normalized nitrogen plasma densities on the inner and outer surfaces of the tube are observed to be about 0.39 and 0.24,respectively,of which the value is 1 at the central plasma source.After a 5μs pulse-on time,in the area less than 2 cm from the end of the tube,the nitrogen ion implantation energy decreases from 1.5 keV to 1.3 keV and the ion implantation angle increases from several degrees to more than 40°;both variations reduce the nitrogen ion implantation depth.However,the nitrogen ion implantation dose peaks of about 2×10^（10）-7×10^（10）ions/cm^2 in this area are 2-4 times higher than that of 1.18×10^（10）ions/cm^2 and 1.63×10^（10）ions/cm^2 on the inner and outer surfaces of the tube.The sufficient ion implantation dose ensures an acceptable modification effect near the end of the tube under the low energy and large angle conditions for nitrogen ion implantation,because the modification effect is mainly determined by the ion implantation dose,just as the mass transfer process in PBLEII is dominated by low-energy ion implantation and thermal diffusion.Therefore,a comparatively uniform surface modification by the low-energy nitrogen ion implantation is achieved along the cylindrical tube on both the inner and outer surfaces.

Earth-observation satellite attitude control using passive and active hybrid magnetically suspended flywheels

The control strategy is presented using passive and active hybrid magnetically suspended flywheels（P＆A MSFWs）,which can help meet the requirements of high precision and high stability for earth-observation satellites.Compared with the conventional flywheel,P＆A MSFW has more rotation degrees of freedom（DOFs）since the rotor is suspended by magnetic bearings,and thus requires more efficient controllers.A modified sliding mode control law（SMC）to our novel nonlinear and coupled system is presented,which is interrupted by inertia matrix uncertainties and external disturbances.SMC law via Lyapunov method is improved,and a fuzzy control scheme is used to attenuate the chatting and control attitude accuracy and maintain the robustness of SMC.Simulation results are provided to illustrate the efficiency of our model by using our control law.

Method of simulating hybrid STT-MTJ/CMOS circuits based on MATLAB/Simulink

The spin-transfer-torque(STT)magnetic tunneling junction(MTJ)device is one of the prominent candidates for spintronic logic circuit and neuromorphic computing.Therefore,building a simulation framework of hybrid STT-MTJ/CMOS(complementary metal-oxide-semiconductor)circuits is of great value for designing a new kind of computing paradigm based on the spintronic devices.In this work,we develop a simulation framework of hybrid STT-MTJ/CMOS circuits based on MATLAB/Simulink,which is mainly composed of a physics-based STT-MTJ model,a controlled resistor,and a current sensor.In the proposed framework,the STT-MTJ model,based on the Landau-Lifshitz-Gilbert-Slonczewsk(LLGS)equation,is implemented using the MATLAB script.The proposed simulation framework is modularized design,with the advantage of simple-to-use and easy-to-expand.To prove the effectiveness of the proposed framework,the STT-MTJ model is benchmarked with experimental results.Furthermore,the pre-charge sense amplifier(PCSA)circuit consisting of two STT-MTJ devices is validated and the electrical coupling of two spin-torque oscillators is simulated.The results demonstrate the effectiveness of our simulation framework.