Synthesis of 3D Hexagram-Like Cobalt–Manganese Sulfides Nanosheets Grown on Nickel Foam: A Bifunctional Electrocatalyst for Overall Water Splitting

The exploration of low-cost and efficient bifunctional electrocatalysts for oxygen evolution reaction and hydrogen evolution reaction through tuning the chemical composition is strongly required for sustainable resources. Herein, we developed a bimetallic cobalt–manganese sulfide supported on Ni foam(CMS/Ni) via a solvothermal method. It has discovered that after combining with the pure Co_9S_8 and Mn S, the morphologies of CMS/Ni have modulated. The obtained three-dimensionally hexagram-like CMS/Ni nanosheets have a significant increase in electrochemical active surface area and charge transport ability. More than that, the synergetic effect of Co and Mn has also presented in this composite. Benefiting from these, the CMS/Ni electrode shows great performance toward hydrogen evolution reaction and oxygen evolution reaction in basic medium, comparing favorably to that ofthe pure Co_9S_8/Ni and Mn S/Ni. More importantly, this versatile CMS/Ni can catalyze the water splitting in a twoelectrode system at a potential of 1.47 V, and this electrolyzer can be efficiently driven by a 1.50 V commercial dry battery.

Effect of manganese sulfide on the precipitation behavior of tin in steel

Tramp elements such as tin are considered harmful to steel because of hot brittleness they induce at high temperatures. Because tramp elements retained in steel scrap will be enriched in new steel due to the difficultly of their removal, studies on the precipitation behavior of tin are essential. In this study, the effects of different inclusions on the precipitation behavior of tin in steel were studied. The results show that the tin-rich phase precipitates at austenite grain boundaries in an Fe-5%Sn alloy without MnS precipitates, whereas Sn precipitates at the boundaries of MnS inclusions in steel that contains MnS precipitates. MnS is more effective than silicon dioxide or aluminum oxide as a nucleation site for the precipitation of the tin phase, which is consistent with the disregistry between the lattice parameters of the tin phase and those of the inclusions.

Early-stage nucleation of manganese sulfide particle and its processing evolution in Fe-3wt.%Si alloys

Manganese sulfide is often referred to as one of important inhibitors in grain-oriented electrical steels, which is of great importance to yield strong Goss texture. However, the early stage of nucleation for such inhibitors and their evolution during the processing has not been well understood. In present work we selected a Fe-3.12wt.%Si- 0.11wt.%Mn-0.021wt.%S model system and used FE-SEM and atom probe tomography （APT） to investigate the precipitation behavior of MnS inhibitors at near atomic scale. It was found that the Si-S enriched clusters with sizes of 5-15 nm were formed close to the MnS particles. The density of inhibitors decreased after large pseudo-plane-strain compression because of the effect of dislocation motion, and then slightly increased again when sample was aged at 200℃ for 48 h. The dislocations and grain boundaries can act as fast diffusion paths and assist the reemergence of Si-S enriched clusters.

Morphology, size and distribution of MnS inclusions in non-quenched and tempered steel during heat treatment

This article reports the morphology, size, and distribution evolution of MnS inclusions in non-quenched and tempered steel during heat treatment. The variation of single large-sized MnS inclusions at high temperature was observed in situ using a confocal scanning laser microscope （CSLM）. The slender MnS inclusions first changed to pearl-like slrings. These small-sized pearls subsequently coalesced and became closer together as the temperature increased. Large-sized MnS inclusions in non-quenched and tempered steel samples with different thermal histories were investigated with respect to the evolution of their morphology, size, and distribution. After 30 min of ovulation at 1573 K, the percentage of MnS inclusions larger than 3 μm decreased from 50.5% to 3.0%. After a 3 h making period, Ostwald ripening occurred. Most MnS inclusions moved from the grain bounda- ries to the interior. The present study demonstrates that heat treatment is an effective method of changing the morphology, size, and distribution of MnS inclusions, especially large-sized ones.

Effects of cooling rate and Al on MnS formation in medium-carbon non-quenched and tempered steels

The effect of Al on the morphology of MnS in medium-carbon non-quenched and tempered steel was investigated at three different cooling rates of 0.24, 0.43, and 200°C·s^-1. The formation mechanisms of three types of MnS were elucidated based on phase diagram information combined with crystal growth models. The morphology of MnS is governed by the precipitation mode and the growth conditions. A monotectic reaction and subsequent fast solidification lead to globular Type I MnS. Type II MnS inclusions with different morphological characteristics form as a result of a eutectic reaction followed by the growth in the Fe matrix. Type III MnS presents a divorced eutectic morphology. At the cooling rate of 0.24°C·s^-1, the precipitation of dispersed Type III MnS is significantly enhanced by the addition of 0.044wt% acid-soluble Al（Als）, while Type II MnS clusters prefer to form in steels with either 0.034wt% or 0.052wt% Als. At the relatively higher cooling rates of 200°C·s^-1 and 0.43°C·s^-1, the formation of Type I and Type II MnS inclusions is promoted, and the influence of Al is negligible. The results of this work are expected to be employed in practice to improve the mechanical properties of non-quenched and tempered steels.

Superior machinability of steel enhanced with BN and MnS particles

The strategy that replacing part of MnS with BN was proposed in order to decrease the sulfur content in sulfur based free-cutting steel. The effects of BN and MnS inclusions on the microstructure and machinability of the steel were systematically investigated. The results show that most of the BN and MnS inclusions exist individually in the steel and only a small amount of them are in a composite state form- ing either isolated particles or clusters of particles. In the case of multi-phased steel, the theoretical calculation predicts that the volume of large BN particles should be 0.7 times of the volume of large MnS particles. The machinability of this type of BN and MnS alloy steel over a wide range of cutting speeds ranging from a low speed appropriate for drilling to a high speed appropriate for turning is confirmed as being equal to or superior to that of an MnS reference steel, even though the sulfur content in the composite steel is only half that of the MnS steel. The aptitude for cutting effect of 240 ppm nitrogen and 115 ppm boron in the composite steel is demonstrated to be equivalent or even better than 1000 ppm sulfur in MnS free-cutting steel.

Influence of sulfur on inclusion and pitting resistance of 316L stainless steel

The effect of the sulfur content on the microstructure and inclusions of 316 L stainless steel was studied by optical microscopy,scanning electron microscopy,and image analysis,and the effect of sulfur on the pitting corrosion resistance of 316 L stainless steel was studied by conducting ferric chloride immersion test and plotting the electrochemical polarization curves.The results show that the added sulfur is mainly in the form of manganese sulfide inclusions in 316 L stainless steel.With increases in the sulfur content,the grade and percentage of the sulfide in the steel gradually increased,and its distribution became increasingly dense.When the sulfur content exceeded0.1%,the number of sulfide inclusions in the sample increased sharply.When the sulfur content reached 0.199%,the sulfides in the steel were primarily in spindle form,and a large number of spindles were found to refine the grain size of 316 L stainless steel.The pitting corrosion weight loss rate of 316 L stainless steel increased with increases in the sulfur content,while the pitting potential gradually decreased.However,the pitting potential of 316 L stainless steel rebounded when the sulfur content reached 0.199%,which may be related to the grain refinement of the test steel and requires further study.